Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optimal estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Estimation of characteristics and stochastic control of an aircraft flying in atmospheric turbulence

An adaptive control technique to improve the flying qualities of an aircraft in turbulence was investigated. The approach taken was to obtain maximum likelihood estimates of the unknown coefficients of the aircraft system and then, using these estimates along with the separation principle, to define the stochastic optimal control. The maximum likelihood estimation technique that accounted for the effects of turbulence provided good estimates of the unknown coefficients and of the turbulence. The assessment of the stochastic optimal control based on the maximum likelihood estimates showed that the desired effects were attained for the regulator problem of minimizing pitch angle and the tracking problem of requiring normal acceleration to follow the pilot input.

Iliff, K. W.↗
DOE OSTI2022

Connecting Material Properties and Redox Flow Cell Cycling Performance through Zero-Dimensional Models

Improvements in redox flow battery (RFB) performance and durability can be achieved through the development of new active materials, electrolytes, and membranes. While a rich design space exists for emerging materials, complex tradeoffs challenge the articulation of unambiguous target criteria, as the relationships between component selection and cycling performance are multifaceted. Here, we derive zero-dimensional, analytical expressions for mass balances and cell voltages under galvanostatic cycling, enabling direct connections between material/electrolyte properties, cell operating conditions, and resulting performance metrics (e.g., energy efficiency, capacity fade). To demonstrate the utility of this modeling framework, we highlight several considerations for RFB design, including upper bound estimation, active species decay, and membrane/separator conductivity-selectivity tradeoffs. Furthermore, we also discuss modalities for extending this framework to incorporate kinetic losses, distributed ohmic losses, and multiple spatial domains. Importantly, because the mass balances are solved analytically, hundreds of cycles can be simulated in seconds, potentially facilitating detailed parametric sweeps, system optimization, and parameter estimation from cycling experiments. More broadly, this approach provides a means for assessing the impact of cell components that simultaneously influence multiple performance-defining processes, aiding in the elucidation of key descriptors and the identification of favorable materials combinations for specific applications.

25 ENERGY STORAGE↗
NASA NTRS2009

Estimation of Faults in DC Electrical Power System

This paper demonstrates a novel optimization-based approach to estimating fault states in a DC power system. Potential faults changing the circuit topology are included along with faulty measurements. Our approach can be considered as a relaxation of the mixed estimation problem. We develop a linear model of the circuit and pose a convex problem for estimating the faults and other hidden states. A sparse fault vector solution is computed by using 11 regularization. The solution is computed reliably and efficiently, and gives accurate diagnostics on the faults. We demonstrate a real-time implementation of the approach for an instrumented electrical power system testbed, the ADAPT testbed at NASA ARC. The estimates are computed in milliseconds on a PC. The approach performs well despite unmodeled transients and other modeling uncertainties present in the system.

Gorinevsky, Dimitry↗
NASA NTRS2000

New Developments in Quaternion Estimation from Vector Observations

This paper contains a critical comparison of estimators minimizing Wahba's loss function. Some new results are presented for the QUaternion ESTimator (QUEST) and EStimators of the Optimal Quaternion (ESOQ and ESOQ2) to avoid the computational burden of sequential rotations in these algorithms. None of these methods is as robust in principle as Davenport's q method or the Singular Value Decomposition (SVD) method, which are significantly slower. Robustness is only an issue for measurements with widely differing accuracies, so the fastest estimators, the modified ESOQ and ESOQ2, are well suited to sensors that track multiple stars with comparable accuracies. More robust forms of ESOQ and ESOQ2 are developed that are intermediate in speed.

Markley, F. Landis↗
NASA NTRS1996

Development of Advanced Methods of Structural and Trajectory Analysis for Transport Aircraft

In this report the author describes: (1) development of advanced methods of structural weight estimation, and (2) development of advanced methods of flight path optimization. A method of estimating the load-bearing fuselage weight and wing weight of transport aircraft based on fundamental structural principles has been developed. This method of weight estimation represents a compromise between the rapid assessment of component weight using empirical methods based on actual weights of existing aircraft and detailed, but time-consuming, analysis using the finite element method. The method was applied to eight existing subsonic transports for validation and correlation. Integration of the resulting computer program, PDCYL, has been made into the weights-calculating module of the AirCraft SYNThesis (ACSYNT) computer program. ACSYNT bas traditionally used only empirical weight estimation methods; PDCYL adds to ACSYNT a rapid, accurate means of assessing the fuselage and wing weights of unconventional aircraft. PDCYL also allows flexibility in the choice of structural concept, as well as a direct means of determining the impact of advanced materials on structural weight.

Ardema, Mark D.↗
DOE OSTI2023

Sparse regression for plasma physics

Many scientific problems can be formulated as sparse regression, i.e., regression onto a set of parameters when there is a desire or expectation that some of the parameters are exactly zero or do not substantially contribute. This includes many problems in signal and image processing, system identification, optimization, and parameter estimation methods such as Gaussian process regression. Sparsity facilitates exploring high-dimensional spaces while finding parsimonious and interpretable solutions. In the present work, we illustrate some of the important ways in which sparse regression appears in plasma physics and point out recent contributions and remaining challenges to solving these problems in this field. Further, a brief review is provided for the optimization problem and the state-of-the-art solvers, especially for constrained and high-dimensional sparse regression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2006

Genetic Algorithm for Optimization: Preprocessing with n Dimensional Bisection and Error Estimation

A knowledge of the appropriate values of the parameters of a genetic algorithm (GA) such as the population size, the shrunk search space containing the solution, crossover and mutation probabilities is not available a priori for a general optimization problem. Recommended here is a polynomial-time preprocessing scheme that includes an n-dimensional bisection and that determines the foregoing parameters before deciding upon an appropriate GA for all problems of similar nature and type. Such a preprocessing is not only fast but also enables us to get the global optimal solution and its reasonably narrow error bounds with a high degree of confidence.

Sen, S. K.↗
NASA NTRS1991

Parameter estimation for distributed parameter models of complex, flexible structures

Distributed parameter modeling of structural dynamics has been limited to simple spacecraft configurations because of the difficulty of handling several distributed parameter systems linked at their boundaries. Although there is other computer software able to generate such models or complex, flexible spacecraft, unfortunately, neither is suitable for parameter estimation. Because of this limitation the computer software PDEMOD is being developed for the express purposes of modeling, control system analysis, parameter estimation and structure optimization. PDEMOD is capable of modeling complex, flexible spacecraft which consist of a three-dimensional network of flexible beams and rigid bodies. Each beam has bending (Bernoulli-Euler or Timoshenko) in two directions, torsion, and elongation degrees of freedom. The rigid bodies can be attached to the beam ends at any angle or body location. PDEMOD is also capable of performing parameter estimation based on matching experimental modal frequencies and static deflection test data. The underlying formulation and the results of using this approach for test data of the Mini-MAST truss will be discussed. The resulting accuracy of the parameter estimates when using such limited data can impact significantly the instrumentation requirements for on-orbit tests.

Taylor, Lawrence W., Jr.↗
DOE OSTI2021

Apparatus and method for optimizing quantifiable behavior in configurable devices and systems

An apparatus and method are provided to perform constrained optimization of a constrained property of an apparatus, which is complex due to having several components, and these components are configurable in real-time. The optimization is achieved by detecting values of the constrained property and a plurality of other properties of the apparatus when the apparatus is configured in a first subset of the plurality of configurations. A model is learned using the detected values of the constrained property. The model represents the constrained property and can also represent other properties as a function of the configurations. The model can also include estimated uncertainties of the constrained property in the model. Then, using the d model and the estimated uncertainties, the optimal configuration can be selected to minimize an error value (e.g., the difference between a desired value and an observed value of the at least one constrained property).

Hoffmann, Henry↗
NASA NTRS2007

Quaternion Averaging

Many applications require an algorithm that averages quaternions in an optimal manner. For example, when combining the quaternion outputs of multiple star trackers having this output capability, it is desirable to properly average the quaternions without recomputing the attitude from the the raw star tracker data. Other applications requiring some sort of optimal quaternion averaging include particle filtering and multiple-model adaptive estimation, where weighted quaternions are used to determine the quaternion estimate. For spacecraft attitude estimation applications, derives an optimal averaging scheme to compute the average of a set of weighted attitude matrices using the singular value decomposition method. Focusing on a 4-dimensional quaternion Gaussian distribution on the unit hypersphere, provides an approach to computing the average quaternion by minimizing a quaternion cost function that is equivalent to the attitude matrix cost function Motivated by and extending its results, this Note derives an algorithm that deterniines an optimal average quaternion from a set of scalar- or matrix-weighted quaternions. Rirthermore, a sufficient condition for the uniqueness of the average quaternion, and the equivalence of the mininiization problem, stated herein, to maximum likelihood estimation, are shown.

Markley, F. Landis↗
NASA NTRS1994

Natural frequency of uniform and optimized tetrahedral truss platforms

Qualitative and quantitative estimates for the fundamental frequency of uniform and optimized tetrahedral truss platforms are determined. A semiempirical equation is developed for the frequency of free-free uniform trusses as a function of member material properties, truss dimensions, and parasitic (nonstructural) mass fraction Mp/Mt. Optimized trusses with frequencies approximately two times those of uniform trusses are determined by varying the cross-sectional areas of member groups. Trusses with 3 to 8 rings, no parasitic mass, and member areas up to 25 times the minimum area are optimized. Frequencies computed for ranges of both Mp/Mt and the ratio of maximum area to minimum area are normalized to the frequency of a uniform truss with no parasitic mass. The normalized frequency increases with the number of rings, and both frequency and the ratio of maximum area to minimum area decrease with increasing Mp/Mt. Frequency improvements that are achievable with a limited number of member areas are estimated for a 3-ring truss by using Taguchi methods. Joint stiffness knockdown effects are also considered. Comparison of optimized and baseline uniform truss frequencies indicates that tailoring can significantly increase structural frequency; maximum gains occur for trusses with low values of Mp/Mt. This study examines frequency trends for ranges of structural parameters and may be used as a preliminary design guide.

Wu, K. Chauncey↗
NASA NTRS1994

A Numerical Comparison of Barrier and Modified Barrier Methods for Large-Scale Bound-Constrained Optimization

When a classical barrier method is applied to the solution of a nonlinear programming problem with inequality constraints, the Hessian matrix of the barrier function becomes increasingly ill-conditioned as the solution is approached. As a result, it may be desirable to consider alternative numerical algorithms. We compare the performance of two methods motivated by barrier functions. The first is a stabilized form of the classical barrier method, where a numerically stable approximation to the Newton direction is used when the barrier parameter is small. The second is a modified barrier method where a barrier function is applied to a shifted form of the problem, and the resulting barrier terms are scaled by estimates of the optimal Lagrange multipliers. The condition number of the Hessian matrix of the resulting modified barrier function remains bounded as the solution to the constrained optimization problem is approached. Both of these techniques can be used in the context of a truncated-Newton method, and hence can be applied to large problems, as well as on parallel computers. In this paper, both techniques are applied to problems with bound constraints and we compare their practical behavior.

Nash, Stephen G.↗
NASA NTRS1999

Melt Stabilization of PbSnTe in a Magnetic Field

Both the experimental observation and numerical simulation indicate that the Bridgman growth of PbSnTe under the microgravity environment in space is still greatly influenced by buoyancy-induced convection. The application of a magnetic field during the semiconductor growth can dampen the convective flow in the metal-like melt. However, for Bridgman growth of PbSnTe on earth (with either vertical or horizontal configuration), both experimental observation and numerical modeling suggest that even with a strong magnetic furnace (5-Tesla constant axial magnetic field), the convective flow in the melt still cannot be sufficiently suppressed to reach the diffusion-controlled level. In order to completely dampen the buoyancy-induced convection on earth, estimates based on scaling analysis indicate that for common experimental conditions, an extremely high magnetic field is required, far beyond the capacity of the experimental apparatus currently available. Therefore, it is proposed that only the combination of microgravity environment and magnetic damping will produce the desired diffusion-controlled growth state for this particular material. The primary objectives of this study are to provide a quantitative understanding of the complex transport phenomena during solidification of non-dilute binarys, to furnish a numerical tool for furnace design and growth condition optimization, to provide estimates of the required magnetic field strength for low gravity growth, and to assess the role of magnetic damping for space and earth control of the double-diffusive convection. As an integral part of a NASA research program, our numerical simulation supports both the flight and ground-based experiments in an effort to bring together a complete picture of the complex physical phenomena involved in the crystal growth process. For Bridgman growth of PbSnTe under microgravity (with both vertical and horizontal configurations), the simulations suggest that a moderate axial magnetic field of only a few kilo-Gauss in strength could effectively eliminate buoyancy-induced convection in the melt and control solute segregation. Therefore, this work confirms the idea that the combination of microgravity environment and the magnetic damping will indeed be sufficient to produce the desired diffusion-controlled growth state for PbSnTe.

Fripp, Archibald L.↗
NASA NTRS1997

Flight Test Validation of Optimal Input Design and Comparison to Conventional Inputs

A technique for designing optimal inputs for aerodynamic parameter estimation was flight tested on the F-18 High Angle of Attack Research Vehicle (HARV). Model parameter accuracies calculated from flight test data were compared on an equal basis for optimal input designs and conventional inputs at the same flight condition. In spite of errors in the a priori input design models and distortions of the input form by the feedback control system, the optimal inputs increased estimated parameter accuracies compared to conventional 3-2-1-1 and doublet inputs. In addition, the tests using optimal input designs demonstrated enhanced design flexibility, allowing the optimal input design technique to use a larger input amplitude to achieve further increases in estimated parameter accuracy without departing from the desired flight test condition. This work validated the analysis used to develop the optimal input designs, and demonstrated the feasibility and practical utility of the optimal input design technique.

Morelli, Eugene A.↗
DOE OSTI2021

SMART-COM – Scalable Multi-Agent Adaptive Resolution Tools for Collaborative Outage Management

The purpose of this grant was to conduct scientific research and prototype applications to support NPP outage staff in their adaptive decision-making in efficient scheduling and resource allocation while preventing violation of safety technical specifications. The project contributed to scientific knowledge and engineering methods in (1) user interface design, (2) scheduling optimization and risk estimation, and (2) natural language processing that would benefit the nuclear power plants in minimizing schedule overruns and even unexpected shutdowns. The research team conducted site visits at a test reactor facility and an operating nuclear power plant to gather necessary information and inputs for research and development of a software application to support NPP staff in executing their outages. The final software application consisted of three modules. First, the natural language processing module supports interactive processing of technical documentation to build a database for outage staff to query non-permissible actions on system components. This module can alleviate outage staff from reviewing extensive documentation and minimize violation of technical specifications, especially in time-sensitive situations. Second, the schedule optimization module schedules outage activities and compute risk indices that outperform existing software and current practice. This module can reduce completion time of an outage that typically have too many activities for human to optimize based on current practice that does not apply the latest operations research. Finally, the visualization module presents progress and risk information of the overall outage and individual activities, as well as enabling access to the natural language processing and schedule optimization modules. This module can provide outage staff with situation awareness that are necessary to make risk-informed decisions in response to unexpected events during the execution of an outage.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Physics-preserving enriched Galerkin method for a fully-coupled thermo-poroelasticity model

This paper proposes a new numerical method for a fully-coupled, quasi-static thermo-poroelasticity model in a unified enriched Galerkin (EG) method framework. In our method, the mechanics sub-problem is solved using a locking-free EG method, and the flow and heat sub-problems are solved using a locally-conservative EG method. The proposed method offers mass and energy conservation properties with much lower costs than other methods with the same properties, including discontinuous Galerkin methods and mixed finite element methods. The well-posedness and optimal a priori error estimates are carefully derived. Here, several numerical tests confirm the theoretical optimal convergence rates and the mass and energy conservation properties of the new method.

15 GEOTHERMAL ENERGY↗
NASA NTRS1997

Application of the Two-Step Filter to Process Ranging Measurements for Relative Navigation in an Elliptical Orbit

This estimator breaks a nonlinear estimation problem into a set of over determined 'first step' states which are linear in the observations and 'second step' states which are ultimately the states of interest. Linear estimation methods are applied to filter the observations and produce the optimal first step state estimate. The 'second step' states are obtained through iterative nonlinear parameter estimation considering the first step states as observations. It has been shown that this process exactly minimizes the least squares cost function for static problems and provides a better solution than the iterated extended Kalman filter (EKF) for dynamic problems. The two step filter is applied in this paper to process range and range rate measurements between the two spacecraft. Details of the application of the two step estimator to this problem will be given, highlighting the use of a test for ill-conditioned covariance estimates that can result from the first order covariance propagation. A comparison will be made between the performance of the two step filter and the IEKF.

Garrison, James L.↗