Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Logging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

AE33 Aethalometer Records at RMBL [AMF2] from April 2022 to October 2023

The dataset presents atmospheric mass loadings of black carbon (BC) and brown carbon (BrC), during the Surface Atmosphere Integrated Field Laboratory (SAIL) campaign that took place from 2021 – 2023 in Gothic, CO. A Magee Scientific aethalometer (model AE33) was deployed at the Rocky Mountain Biological Laboratory, 200 m north of AMF2 to monitor mass loadings of optically absorbing aerosols. The instrument inlet was equipped with a BGI SCC 1.829 ambient cyclone with a particle cutoff of 2.5 μm and placed 5 m above ground level. The dataset reports hour-resolved BC mass loadings at 370, 470, 520, 590, 660, 880, and 950 (BC370, BC470, BC 520, BC590, BC660, BC880, BC950 in ng/m3) reported by the instrument built-in algorithm, which calculates mass loadings from the rate of change of the attenuation of light transmitted through the aerosol-laden filter. BC880 is the operationally defined reference of the BC concentration. Hour-resolved absorbance at each wavelength were calculated from their respective mass absorption cross-section in inverse megameters (Mm-1). The absorption Angstrom exponent (AAE) for BrC and BC were calculated for each hour. BrC AAE (AAE_BrC) was calculated from the slope of Log(wavelength) versus Log(absorbance) based on the measurements at 370, 470, and 520 nm. BC AAE (AAE_BrC) was calculated from the slope of Log(wavelength) versus Log(absorbance) based on the measurements at 590, 660, 880, and 950 nm. The aethalometer record spans time periods of 4/5/2022 – 10/3/2022 and 12/8/2022 – 10/9/2023. The ambient CO2 concentration recorded by a Vaisala CARBOCAP carbon dioxide probe GMP343 is also reported in ppm.

54 ENVIRONMENTAL SCIENCES↗

BSEC Air Quality: Stationary Black and Brown Carbon Properties and Mass Concentration

Data is 1-min absorption/attenuation of aerosol collected on filter and sampled at seven wavelengths (950, 880, 660, 590, 520, 470, and 370 nm) with a Magee AE-33 dual spot aethalometer. The wavelength value for black carbon, as recommended by the manufacturer, is the 880 nm channel. The derived mass concentrations, using the factory default mass absorption cross-sections, are reported for all seven wavelengths. The absorption at all seven wavelengths are reported by dividing the derived mass concentrations by the factory default mass absorption cross-sections. The estimated mass concentration contribution from biomass burning and fossil fuel black carbon, using factory default values, are reported. The estimated brown carbon mass concentration is derived by finding the difference between the recommended black carbon wavelength (880 nm) and the ultra violet wavelength (370 nm), assuming that brown carbon absorption is strongest at 370 nm and minimal at 880 nm. Finally, the estimated absorption Angstrom exponent for black and brown carbon is derived. For black carbon, the slope between each minute log(AbsXXX), where XXX is the wavelength used versus log(XXX) is used, and the wavelengths are 590, 660, 880, and 950 nm. For brown carbon, the slope between each minute log(AbsXXX), where XXX is the wavelength used versus log(XXX) is used, and the wavelengths are 370, 470, and 520 nm.

aerosol↗

Investigation of Neutron Detector Response to Varying Temperature and Water Content for Geothermal Applications

Nuclear logging techniques have been used for oil well logging applications for decades. The basic principle is to use a neutron and/or photon source and neutron and photon detectors for characterization purposes. Although the technology has matured, it is not directly applicable to geothermal logging due to even more challenging environmental conditions, both in terms of temperature and pressure. For geothermal logging, the operating temperature can go up to 376 C for depths up to 10,000 km. In this paper, the preliminary computational results for thermal neutron detector response for varying temperature and water content for geothermal applications are presented. In this summary, preliminary results for neutron detector response for varying formation temperature and water content are presented. The analysis is performed for a steady state source (AmBe) and time dependent source (PNG) in pulsed mode. The computational results show significant sensitivity to water content as well as temperature changes for both steady state and time dependent measurements. As expected, the most significant change is due to the temperature change for S({alpha}, {beta}) nuclear data instead of individual isotope cross sections for the formation. Clearly, this is partially because of the fact that strong absorbers (i.e., chlorine) are not taken into account for the analysis at this time. The computational analysis was performed using the temperature dependent data in the ENDF/B-VII libraries, supplied with MCNP. Currently, the data for intermediate temperatures are being generated using NJOY and validated. A series of measurements are planned to validate the computational results. Further measurements are planned to determine the neutron and photon detector response as a function of temperature. The tests will be performed for temperatures up to 400 C.

02 PETROLEUM↗

3-Dimensional Root Cause Diagnosis via Co-analysis

With the growth of system size and complexity, reliability has become a major concern for large-scale systems. Upon the occurrence of failure, system administrators typically trace the events in Reliability, Availability, and Serviceability (RAS) logs for root cause diagnosis. However, RAS log only contains limited diagnosis information. Moreover, the manual processing is time-consuming, error-prone, and not scalable. To address the problem, in this paper we present an automated root cause diagnosis mechanism for large-scale HPC systems. Our mechanism examines multiple logs to provide a 3-D fine-grained root cause analysis. Here, 3-D means that our analysis will pinpoint the failure layer, the time, and the location of the event that causes the problem. We evaluate our mechanism by means of real logs collected from a production IBM Blue Gene/P system at Oak Ridge National Laboratory. It successfully identifies failure layer information for 219 failures during 23-month period. Furthermore, it effectively identifies the triggering events with time and location information, even when the triggering events occur hundreds of hours before the resulting failures.

Zheng, Ziming↗

DISPLACEMENT CASCADE SIMULATION IN TUNGSTEN AT 1025 K

Molecular dynamics simulation was employed to investigate the irradiation damage properties of bulk tungsten at 1025 K (0.25 melting temperature). A comprehensive data set of primary cascade damage was generated up to primary knock-on atom (PKA) energies 100 keV. The dependence of the number of surviving Frenkel pairs (NFP) on the PKA energy (E) exhibits three different characteristic domains presumably related to the different cascade morphologies that form. The low-energy regime < 0.2 keV is characterized by a hit-or-miss type of Frenkel pair (FP) production near the displacement threshold energy of 128 eV. The middle regime 0.3 – 30 keV exhibits a sublinear dependence of log(NFP) vs log(E) associated with compact cascade morphology with a slope of 0.73. Above 30 keV, the cascade morphology consists of complex branches or interconnected damage regions. In this extended morphology, large interstitial clusters form from superposition of interstitials from nearby damage regions. Strong clustering above 30 keV results in a superlinear dependence of log(NFP) vs log(E) with a slope of 1.365. At 100 keV, an interstitial cluster of size 92 and a vacancy cluster of size 114 were observed.

cascade↗

Cloud object store for archive storage of high performance computing data using decoupling middleware

Cloud object storage is enabled for archived data, such as checkpoints and results, of high performance computing applications using a middleware process. A plurality of archived files, such as checkpoint files and results, generated by a plurality of processes in a parallel computing system are stored by obtaining the plurality of archived files from the parallel computing system; converting the plurality of archived files to objects using a log structured file system middleware process; and providing the objects for storage in a cloud object storage system. The plurality of processes may run, for example, on a plurality of compute nodes. The log structured file system middleware process may be embodied, for example, as a Parallel Log-Structured File System (PLFS). The log structured file system middleware process optionally executes on a burst buffer node.

97 MATHEMATICS AND COMPUTING↗

The Potosi Reservoir Model 2013

As a part of a larger project co-funded by the United States Department of Energy (US DOE) to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon as potential targets for carbon sequestration in the Illinois and Michigan Basins, the Illinois Clean Coal Institute (ICCI) requested Schlumberger to evaluate the potential injectivity and carbon dioxide (CO2) plume size of the Cambrian Potosi Formation. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data from the US DOE-funded Illinois Basin–Decatur Project (IBDP) being conducted by the Midwest Geological Sequestration Consortium in Macon County, Illinois. In 2010, technical performance evaluations on the Cambrian Potosi Formation were performed through reservoir modeling. The data included formation tops from mud logs, well logs from the VW1 and the CCS1 wells, structural and stratigraphic formation from three dimensional (3D) seismic data, and field data from several waste water injection wells for Potosi Formation. Intention was for two million tons per annum (MTPA) of CO2 to be injected for 20 years. In the preceding, the 2010 Potosi heterogeneous model (referred to as the "Potosi Dynamic Model 2010" in this topical report) was re-run using a new injection scenario; 3.2 MTPA for 30 years. The extent of the Potosi Dynamic Model 2010, however, appeared too small for the new injection target. It was not sufficiently large enough to accommodate the evolution of the plume. The new model, Potosi Dynamic Model 2013a, was built by extending the Potosi Dynamic Model 2010 grid to 30 miles x 30 miles (48.3km x48.3km), while preserving all property modeling workflows and layering. This model was retained as the base case of Potosi Dynamic Model 2013a. The Potosi reservoir model was updated to take into account the new data from the verification well VW2 which was drilled in 2012. The new porosity and permeability modeling was performed to take into account the log data from the new well. Revisions of the 2010 modeling assumptions were also done on relative permeability, capillary pressures, formation water salinity, and the maximum allowable well bottomhole pressure. Dynamic simulations were run using the injection target of 3.2 MTPA for 30 years. This new dynamic model was named Potosi Dynamic Model 2013b. Due to the major uncertainties on the vugs permeability, two models were built; the Pessimistic and Optimistic Cases. The Optimistic Case assumes vugs permeability of 9,000 mD, which is analog to the vugs permeability identified in the pressure fall off test of a waste water injector in the Tuscola site, approx. 40 miles (64.4km) away from the IBDP area. The Pessimistic Case assumes that the vugs permeability is equal to the log data, which does not take into account the permeability from secondary porosity. The probability of such case is deemed low and could be treated as the worst case scenario, since the contribution of secondary porosity to the permeability is neglected and the loss circulation events might correspond to a much higher permeability. It is considered important, however, to identify the range of possible reservoir performance since there are no rigorous data available for the vugs permeability. The Optimistic Case gives an average CO2 injection rate of 0.8 MTPA and cumulative injection of 26 MT in 30 years, which corresponds to 27% of the injection target. The injection rate is approx. 3.2 MTPA in the first year as the well is injecting into the surrounding vugs, and declines rapidly to 0.8 MTPA in year 4 once the surrounding vugs are full and the CO2 start to reach the matrix. This implies that according to this preliminary model, a minimum of four (4) wells could be required to achieve the injection target. This result is lower than the injectivity estimated in the Potosi Dynamic Model 2013a (43 MT in 30 years), since the permeability model applied in the Potosi Dynamic Model 2013b is more conservative. This revision was deemed necessary to treat the uncertainty in a more appropriate manner. As the CO2 follows the paths where vugs interconnection exists, a reasonably large and irregular plume extent was created. For the Optimistic Case, the plume extends 17 miles (27.4km) in E-W and 14 miles (22.5km) in N-S directions after 30 years. After injection is completed, the plume continues to migrate laterally, mainly driven by the remaining pressure gradient. After 100 years post injection, the plume extends 20 miles (32.2km) in E-W and 15.5 miles (24.9km) in N-S directions. Should the targeted cumulative injection of 96 MT be achieved; a much larger plume extent could be expected. For the Optimistic Case, the increase of reservoir pressure at the end of injection is approximately 1200 psia (8,274 kPa) around the injector and gradually decreases away from the well. The reservoir pressure increase is less than 30 psia (206.8 kPa) beyond 14 miles (22.5km) away from injector. Should the targeted cumulative injection of 96 MT be achieved; a much larger areal pressure increase could be expected. The initial reservoir pressure is nearly restored after approximately 100 years post injection. The presence of matrix slows down the pressure dissipations. The Pessimistic Case gives an average CO2 injection rate of 0.2 MTPA and cumulative injection of 7 MT in 30 years, which corresponds to 7% of the injection target. This implies that in the worst case scenario, a minimum of sixteen (16) wells could be required to achieve the injection target. The present evaluation is mainly associated with uncertainty on the vugs permeability, distribution, and interconnectivity. The different results indicated by the Optimistic and Pessimistic Cases signify the importance of vugs permeability characterization. Therefore, injection test and pressure interference test among the wells could be considered to evaluate the local vugs permeability, extent, and interconnectivity. Porosity mapping derived from the seismic inversion could also be used in the succeeding task to characterize the lateral porosity distribution within the reservoir. With or without seismic inversion porosity mapping, it is worth exploring whether increased lateral heterogeneity plays a significant role in Potosi injectivity. Investigations on vugular, dolomitic outcrops suggest that there may be significantly greater lateral heterogeneity than what has been modeled here. Facies modeling within the Potosi has yet to be thoroughly addressed. The carbonates during the time of deposition are believed to be regionally extensive. However, it may be worth delineating the reservoir with other regional wells or modern day analogues to understand the extent of the Potosi. More specifically, the model could incorporate lateral changes or trends if deemed necessary to represent facies transition. Data acquisitions to characterize the fracture pressure gradient, the formation water properties, the relative permeability, and the capillary pressure could also be considered in order to allow a more rigorous evaluation of the Potosi storage performance. A simulation using several injectors could also be considered to determine the required number of wells to achieve the injection target while taking into account the pressure interference.

Adushita, Yasmin↗

The Potosi Reservoir Model 2013c, Property Modeling Update

As part of a larger project co-funded by the United States Department of Energy (US DOE) to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon as potential targets for carbon sequestration in the Illinois and Michigan Basins, the Illinois Clean Coal Institute (ICCI) requested Schlumberger to evaluate the potential injectivity and carbon dioxide (CO2) plume size of the Cambrian Potosi Formation. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data from this project as well as two other separately funded projects: the US DOE-funded Illinois Basin–Decatur Project (IBDP) being conducted by the Midwest Geological Sequestration Consortium (MGSC) in Macon County, Illinois, and the Illinois Industrial Carbon Capture and Sequestration (ICCS) project funded through the American Recovery and Reinvestment Act. In 2010, technical performance evaluations on the Cambrian Potosi Formation were performed through reservoir modeling. The data included formation tops from mud logs, well logs from the Verification Well #1 (VW1) and the Injection Well (CCS1), structural and stratigraphic formation from three dimensional (3D) seismic data, and field data from several waste water injection wells for Potosi Formation. The intention was for 2.2 million tons per annum (2 million tonnes per annum [MTPA]) of CO2 to be injected for 20 years. In the Task Error! Reference source not found., the 2010 Potosi heterogeneous model (referred to as the "Potosi Dynamic Model 2010") was re-run using a new injection scenario of 3.5 million tons per annum (3.2 MTPA) for 30 years. The extent of the Potosi Dynamic Model 2010, however, appeared too small for the new injection target. The models size was insufficient to accommodate the evolution of the plume. The new model, Potosi Dynamic Model 2013a, was built by extending the Potosi Dynamic Model 2010 grid to 30 by 30 mi (48 by 48 km), while preserving all property modeling workflows and layering. This model was retained as the base case. In the preceding Task [1], the Potosi reservoir model was updated to take into account the new data from the Verification Well #2 (VW2) which was drilled in 2012. The porosity and permeability modeling was revised to take into account the log data from the new well. Revisions of the 2010 modeling assumptions were also done on relative permeability, capillary pressures, formation water salinity, and the maximum allowable well bottomhole pressure. Dynamic simulations were run using the injection target of 3.5 million tons per annum (3.2 MTPA) for 30 years. This dynamic model was named Potosi Dynamic Model 2013b. In this Task, a new property modeling workflow was applied, where seismic inversion data guided the porosity mapping and geobody extraction. The static reservoir model was fully guided by PorosityCube interpretations and derivations coupled with petrophysical logs from three wells. The two main assumptions are: porosity features in the PorosityCube that correlate with lost circulation zones represent vugular zones, and that these vugular zones are laterally continuous. Extrapolation was done carefully to populate the vugular facies and their corresponding properties outside the seismic footprint up to the boundary of the 30 by 30 mi (48 by 48 km) model. Dynamic simulations were also run using the injection target of 3.5 million tons per annum (3.2 MTPA) for 30 years. This new dynamic model was named Potosi Dynamic Model 2013c. Reservoir simulation with the latest model gives a cumulative injection of 43 million tons (39 MT) in 30 years with a single well, which corresponds to 40% of the injection target. The injection rate is approx. 3.2 MTPA in the first six months as the well is injecting into the surrounding vugs, and declines rapidly to 1.8 million tons per annum (1.6 MTPA) in year 3 once the surrounding vugs are full and the CO2 start to reach the matrix. After, the injection rate declines gradually to 1.2 million tons per annum (1.1 MTPA) in year 18 and stays constant. This implies that a minimum of three (3) wells could be required in the Potosi to reach the injection target. The injectivity evaluated in this Task was higher compared to the preceding Task, since the current facies modeling (guided by the porosity map from the seismic inversion) indicated a higher density of vugs within the vugular zones. 5 As the CO2 follows the paths where vugs interconnection exists, a reasonably large and irregular plume extent was created. After 30 years of injection, the plume extends 13.7 mi (22 km) in E-W and 9.7 mi (16 km) in N-S directions. After injection finishes, the plume continues to migrate laterally, mainly driven by the remaining pressure gradient. After 60 years post-injection, the plume extends 14.2 mi (22.8 km) in E-W and 10 mi (16 km) in N-S directions, and remains constant as the remaining pressure gradient has become very low. Should the targeted cumulative injection of 106 million tons (96 MT) be achieved; a much larger plume extent could be expected. The increase of reservoir pressure at the end of injection is approximately 1,200 psia (8,274 kPa) around the injector and gradually decreases away from the well. The reservoir pressure increase is less than 10 psia (69 kPa) beyond 14 mi (23 km) away from injector. Should the targeted cumulative injection of 106 million tons (96 MT) be achieved; a much larger areal pressure increase could be expected. The reservoir pressure declines rapidly during the first 30 years post injection and the initial reservoir pressure is nearly restored after 100 years post-injection. The present evaluation is mainly associated with uncertainty on the vugs permeability and interconnectivity. The use of porosity mapping from seismic inversion might have reduced the uncertainty on the lateral vugs body distributions. However, major uncertainties on the Potosi vugs permeability remains. Therefore, injection test and pressure interference test among the wells could be considered to evaluate the local vugs permeability, extent, and interconnectivity. Facies modeling within the Potosi has yet to be thoroughly addressed. The carbonates during the time of deposition are believed to be regionally extensive. However, it may be worth delineating the reservoir with other regional wells or modern day analogues to understand the extent of the Potosi. More specifically, the model could incorporate lateral changes or trends if deemed necessary to represent facies transition. Data acquisitions to characterize the fracture pressure gradient, the formation water properties, the relative permeability, and the capillary pressure could also be considered in order to allow a more rigorous evaluation of the Potosi storage performance. A simulation using several injectors could also be considered to determine the required number of wells and appropriate spacing to achieve the injection target while taking into account the pressure interference.

Adushita, Yasmin↗

Gnawts

High Performance Computing (HPC) systems generate millions of inter-related event log lines per day from thousands of computers, providing feedback on both successful and unsuccessful operations within the system. Thorough analysis of these logs is often required for root cause analysis of problems and tuning for greatest performance. This "app" for the "Gnawts" log analysis software (http://www.gnawts.com) facilitates faster and deeper insights into HPC system logs.

Jon Stearley, Charles Snider↗

Cloud object store for checkpoints of high performance computing applications using decoupling middleware

Cloud object storage is enabled for checkpoints of high performance computing applications using a middleware process. A plurality of files, such as checkpoint files, generated by a plurality of processes in a parallel computing system are stored by obtaining said plurality of files from said parallel computing system; converting said plurality of files to objects using a log structured file system middleware process; and providing said objects for storage in a cloud object storage system. The plurality of processes may run, for example, on a plurality of compute nodes. The log structured file system middleware process may be embodied, for example, as a Parallel Log-Structured File System (PLFS). The log structured file system middleware process optionally executes on a burst buffer node.

97 MATHEMATICS AND COMPUTING↗

A New Record Census of Dwarf AGN and a Bimodal $M_{\rm BH}$-$M_{\star}$ Scaling Relation with DESI DR1

Using the first spectroscopic data release from the Dark Energy Spectroscopic Instrument (DESI DR1), we search for AGN signatures in 1,678,787 low-redshift ($0.001 \le z \le 0.45$) line-emitting galaxies. Based on the [NII]-BPT emission-line ratio diagnostic, we identify AGN in 314,245/1,211,573 (25.9%) high-mass ($\log (M_{\star}/M_{\odot}) > 9.5$) and 9648/467,214 (2.1%) dwarf ($\log (M_{\star}/M_{\odot}) \le 9.5$) galaxies. Among these AGN, 17,949 are broad-line candidates (BL-AGN) with broad H$α$ emission, enabling black hole (BH) mass estimates using single-epoch virial methods. We find that the AGN fraction in line-emitting galaxies increases monotonically with stellar mass, rising from $\sim$1.4% at the low-mass end to $\sim$93.3% at the high-mass end. Using the large BL-AGN sample, we extend the $M_{\rm BH} - M_{\star}$ scaling relation down to $\log (M_{\star}/M_{\odot}) \approx 7.8$ and $\log (M_{\rm BH}/M_{\odot}) \approx 4.4$. In the context of high-redshift overmassive BHs, our results suggest that galaxies and their central BHs may follow two distinct evolutionary pathways across cosmic time. With this paper, we release the EmFit value-added catalog, containing emission-line flux and width measurements for $\sim$7.4 million galaxies, the largest catalog with emission-line decomposition into narrow, broad, and outflow components to date. This work significantly expands upon the early DESI results and provides a statistical sample for probing the galaxy$-$BH connection in the low-mass galaxy regime.

Pucha, Ragadeepika [Utah U.; Arizona U., Astron. D↗

EFFECT OF TEMPERATURE AND HUMIDITY ON FORMALDEHYDE EMISSIONS IN TEMPORARY HOUSING UNITS

The effect of temperature and humidity on formaldehyde emissions from samples collected from temporary housing units (THUs) was studied. The THUs were supplied by the U.S Federal Emergency Management Administration (FEMA) to families that lost their homes in Louisiana and Mississippi during the Hurricane Katrina and Rita disasters. Based on a previous study 1, 2, four of the composite wood surface materials that dominated contributions to indoor formaldehyde were selected to analyze the effects of temperature and humidity on the emission factors. Humidity equilibration experiments were carried out on two of the samples to determine how long the samples take to equilibrate with the surrounding environmental conditions. Small chamber experiments were then conducted to measure emission factors for the four surface materials at various temperature and humidity conditions. The samples were analyzed for formaldehyde via high performance liquid chromatography. The experiments showed that increases in temperature or humidity contributed to an increase in emission factors. A linear regression model was built using natural log of percentage relative humidity (RH) and inverse of temperature (in K) as predictor variables, and natural log of emission factors as the target variable. The coefficients of both inverse temperature and log relative humidity with log emission factor were found to be statistically significant for all the samples at the 95percent confidence level. This study should assist to retrospectively estimate indoor formaldehyde exposures of occupants of temporary housing units (THUs).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Counting independent sets using the Bethe approximation

The authors consider the problem of counting the number of independent sets or the partition function of a hard-core model in a graph. The problem in general is computationally hard (P hard). They study the quality of the approximation provided by the Bethe free energy. Belief propagation (BP) is a message-passing algorithm can be used to compute fixed points of the Bethe approximation; however, BP is not always guarantee to converge. As the first result, they propose a simple message-passing algorithm that converges to a BP fixed pont for any grapy. They find that their algorithm converges within a multiplicative error 1 + {var_epsilon} of a fixed point in {Omicron}(n{sup 2}E{sup -4} log{sup 3}(nE{sup -1})) iterations for any bounded degree graph of n nodes. In a nutshell, the algorithm can be thought of as a modification of BP with 'time-varying' message-passing. Next, they analyze the resulting error to the number of independent sets provided by such a fixed point of the Bethe approximation. Using the recently developed loop calculus approach by Vhertkov and Chernyak, they establish that for any bounded graph with large enough girth, the error is {Omicron}(n{sup -{gamma}}) for some {gamma} > 0. As an application, they find that for random 3-regular graph, Bethe approximation of log-partition function (log of the number of independent sets) is within o(1) of corret log-partition - this is quite surprising as previous physics-based predictions were expecting an error of o(n). In sum, their results provide a systematic way to find Bethe fixed points for any graph quickly and allow for estimating error in Bethe approximation using novel combinatorial techniques.

97 MATHEMATICS AND COMPUTING↗

Machine learning and deep learning for mineralogy interpretation and CO 2 saturation estimation in geological carbon Storage: A case study in the Illinois Basin

Carbon capture and storage (CCS) is a promising approach to simultaneously maintaining energy security and reducing carbon dioxide (CO 2 ) emissions under the current energy portfolio that is dominated by fossil fuel energy. Pre-injection formation characterization and post-injection CO 2 monitoring are two critical tasks to guarantee storage efficiency in CCS. The CCS projects in the Illinois Basin, the first large-scale CO 2 injection into saline aquifers in the United States, employed conventional and the latest pulsed neutron logging (PNL) tools for mineralogy interpretation and CO 2 saturation estimation, which provide valuable references for future CCS projects. Because of the inherent fuzziness of petrophysical measurements and complex subsurface heterogeneity, interpreting well-logging data is time-consuming, and its accuracy can be user-biased. In recent years, data-driven methods have been widely used to capture the non-linear patterns between input features and interpretation results. This work applied and evaluated four commonly used machine learning (ML) models, including ridge regression (RR), random forest (RF), gradient boosting regression (GBR), support vector regression (SVR), and one deep learning (DL) model, the artificial neural network (ANN). We optimized the hyperparameters of the four ML models and the DL model using the simulated annealing algorithm and the grid search strategy, respectively. The input features of the mineralogy interpretation models were eleven conventional well-logging parameters, and the label data (i.e., ground truth) were the porosity and volumetric fractions of six minerals, including quartz, feldspar, dolomite, calcite, clay, and iron minerals. The results demonstrated that the GBR and RF models were superior in predicting volumetric fractions of minerals and porosity; label data with low coefficient of variation (CV) values tended to yield better performance. For CO 2 saturation estimation, the RF was the best-performing model, followed by SVR, ANN, GBR, and RR. Furthermore, we conducted feature importance ranking using the permutation importance algorithm and found that the formation sigma and well pressure were the most important features in this study. In conclusion, the study of CCS projects in the Illinois Basin bridges the gap between the limited knowledge and understanding of geological carbon storage and the increasing demand for reliable, cost-effective, and sustainable energy solutions.

58 GEOSCIENCES↗

Hawthorne Nevada Deep Direct-Use Feasibility Study - Data Used for Geothermal Resource Conceptual Modeling and Power Capacity Estimates

This data submission includes several data components that were used to develop a conceptual model and power capacity-estimates of two low-temperature geothermal resources that define geothermal prospect A at Hawthorne, Nevada. Data are sourced from a combination of legacy publicly-available data and more recent data acquisition conducted by the US Navy Geothermal Program Office (2008-2013) and the Great Basin Center for Geothermal Energy at the University of Nevada, Reno (2008-2010). Data sets include compiled fluid geochemistry data, down-hole temperature logs for wells in the vicinity of prospect A, 2 meter temperature survey data, temperature-spinner logs acquired in well HWAAD-2A, fracture picks from image log data acquired in wells HWAAD-2 and HWAAD-3, and X-Ray Diffraction (XRD) analyses on cuttings from wells HWAAD-2A and HWAAD-3. These data have been reviewed for errors and inconsistencies, but it is possible that few errors could still remain. The resource conceptual model and power capacity estimates are included in the final report to the US Department of Energy, and are presented in a manuscript by Ayling and Hinz. A link to the manuscript published in Geothermics is linked below in this submission.

15 GEOTHERMAL ENERGY↗

The hydrogen-poor superluminous supernova iPTF 13ajg and its host galaxy in absorption and emission

We present imaging and spectroscopy of a hydrogen-poor superluminous supernova (SLSN) discovered by the intermediate Palomar Transient Factory, iPTF 13ajg. At a redshift of z = 0.7403, derived from narrow absorption lines, iPTF 13ajg peaked at an absolute magnitude of M {sub u,} {sub AB} = –22.5, one of the most luminous supernovae to date. The observed bolometric peak luminosity of iPTF 13ajg is 3.2 × 10{sup 44} erg s{sup –1}, while the estimated total radiated energy is 1.3 × 10{sup 51} erg. We detect narrow absorption lines of Mg I, Mg II, and Fe II, associated with the cold interstellar medium in the host galaxy, at two different epochs with X-shooter at the Very Large Telescope. From Voigt profile fitting, we derive the column densities log N(Mg I) =11.94 ± 0.06, log N(Mg II) =14.7 ± 0.3, and log N(Fe II) =14.25 ± 0.10. These column densities, as well as the Mg I and Mg II equivalent widths of a sample of hydrogen-poor SLSNe taken from the literature, are at the low end of those derived for gamma-ray bursts (GRBs) whose progenitors are also thought to be massive stars. This suggests that the environments of hydrogen-poor SLSNe and GRBs are different. From the nondetection of Fe II fine-structure absorption lines, we derive a lower limit on the distance between the supernova and the narrow-line absorbing gas of 50 pc. The neutral gas responsible for the absorption in iPTF 13ajg exhibits a single narrow component with a low velocity width, ΔV = 76 km s{sup –1}, indicating a low-mass host galaxy. No host galaxy emission lines are detected, leading to an upper limit on the unobscured star formation rate (SFR) of SFR{sub [O} {sub II]}<0.07M{sub ⊙}yr{sup −1}. Late-time imaging shows the iPTF 13ajg host galaxy to be faint, with g {sub AB} ≈ 27.0 and R {sub AB} ≥ 26.0 mag, corresponding to M {sub B,} {sub Vega} ≳ –17.7 mag.

79 ASTRONOMY AND ASTROPHYSICS↗

Subsurface Characterization of Hydraulic Fracture Test Site-2 (HFTS-2), Delaware Basin

Hydraulic Fracturing Test Site-2 (HFTS-2) is a field-based research experiment performed in the Wolfcamp Formation of the Permian (Delaware) Basin. This paper focuses on integration, advanced geological characterization, and 3D subsurface modeling of the comprehensive HFTS-2 dataset. The study showcases a multidisciplinary reservoir characterization approach that incorporates geology, petrophysics, geochemistry, geomechanics, microseismic, and subsurface engineering analysis. Subsurface characterization of organic-rich mudstone formations requires understanding complex hydraulic fracture network growth in relation to inherent lithology, geomechanical properties, and interaction with pre-existing natural fractures. This paper presents a characterization workflow incorporating pre- and post-stimulation subsurface data, unique to the HFTS-2 dataset. The study integrated: (1) rock properties from logs, cores, and thin sections; (2) natural and hydraulic fracture descriptions from cores and image logs; (3) local and regional stresses; (4) geomechanics; (5) microseismic; (6) fiber optic (FO) and bottomhole pressure gauge (BHPG) response; and (7) produced fluids analysis. During a stimulation treatment, creation of the stimulated rock volume (SRV) is influenced by several subsurface factors. Key contributing factors include structural context, stress conditions, lithology, facies architecture, pre-existing natural fractures, and geomechanical properties. The HFTS-2 subsurface data integration indicates that the SRV is comprised of a complex juxtaposition of hydraulic fracture swarms, as evidenced by image logs analysis, core description, and microseismic monitoring. The HFTS-2 microseismic event density was used to generate 3D heat maps that serve as a representative SRV footprint, corroborated by secondary datasets. These maps were further integrated with petrophysical and geomechanical characteristics, as well as responses from FO and BHPG, to estimate the lateral and vertical dimensions of the effective fractures. The geological characterization for the HFTS-2 dataset combined with 3D modeling for petrophysical and geomechanical properties provides a strong foundation for subsurface simulation and optimization studies. Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/1-21URTC/D011S005R001/2477501/urtec-2021-5243-ms.pdf/1 by Carol Worster on 28 February 2022 URTeC 5243 The workflow improved our understanding of HFTS-2 hydraulic fracture propagation and characteristics in relation to offset pressure depletion and interaction with pre-existing natural fractures. Analysis showed that fracture geometry varies by stage and by well, and a complex fracture network is generated with varying fracture density. The multidisciplinary workflow presented herein for integration and characterization serves as a foundation to evaluate completion efficiency and estimate areal and vertical stimulation and depletion extent for the project. Furthermore, the workflow and learnings can also be transferred to other unconventional plays.

58 GEOSCIENCES↗

Offshore CO2 Saline Storage Assessment Dataset

Dataset containing 646 petrophysical well log interpretations spanning multiple geologic domains (as defined by Subsurface Trend Analysis™) in the Gulf of Mexico. Well logs were manually interpreted by geologic researchers at NETL and were derived from BOEM Sands and IHS data raster logs. This interpretation dataset underpins the Offshore CO2 Saline Storage Calculator.

Petrophyiscal↗