SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS1996

Effects of Nonequilibrium at Edge of Boundary Layer on Convective Heat Transfer to a Blunt Body

This investigation is a continuation of a previous study on nonequilibrium convective heat transfer to a blunt body. In the previous study, for relatively high Reynolds number flows, it was found that: nonequilibrium convective heat transfer to a blunt body is not strongly dependent on freestream parameters, provided that the thermochemical equilibrium is reached at the edge of boundary layer; and successful testing of convective heat transfer in an arc-jet environment is possible by duplicating the surface pressure and total enthalpy. The nonequilibrium convective heat transfer computations are validated against the results of Fay and Riddell/Goulard theory. Present work investigates low Reynolds number conditions which are typical in an actual arc-jet flow environment. One expects that there will be departures from the Fay and Riddell/Goulard result since certain assumptions of the classical theory are not satisfied. These departures are of interest because the Fay and Riddell/Goulard formulas are extensively used in arc-jet testing (e.g., to determine the enthalpy of the flow and the catalytic efficiency of heat shield materials). For practical sizes of test materials, density of the test flow (and Reynolds number) in an arc-jet is such that thermochemical equilibrium may not be reached at the edge of boundary layer. For blunt body flows of nitrogen and air, computations will be presented to show the effects of thermochemical nonequilibrium at the boundary layer edge on nonequilibrium heat transfer.

Goekcen, Tahir↗

NASA NTRS2002

Virtual Shaping of a Two-dimensional NACA 0015 Airfoil Using Synthetic Jet Actuator

The Aircraft Morphing Program at NASA Langley envisions an aircraft without conventional control surfaces. Instead of moving control surfaces, the vehicle control systems may be implemented with a combination of propulsive forces, micro surface effectors, and fluidic devices dynamically operated by an intelligent flight control system to provide aircraft maneuverability over each mission segment. As a part of this program, a two-dimensional NACA 0015 airfoil model was designed to test mild maneuvering capability of synthetic jets in a subsonic wind tunnel. The objective of the experiments is to assess the applicability of using unsteady suction and blowing to alter the aerodynamic shape of an airfoil with a purpose to enhance lift and/or to reduce drag. Synthetic jet actuation at different chordwise locations, different forcing frequencies and amplitudes, under different freestream velocities are investigated. The effect of virtual shape change is indicated by a localized increase of surface pressure in the neighborhood of synthetic jet actuation. That causes a negative lift to the airfoil with an upper surface actuation. When actuation is applied near the airfoil leading edge, it appears that the stagnation line is shifted inducing an effect similar to that caused by a small angle of attack to produce an overall lift change.

Chen, Fang-Jenq↗

NASA NTRS1991

Phenomenological and experimental study of the thermal response of low density silica ablators to high enthalpy plasma flows

A complete analysis of the melting-ablator governing equations is carried out for porous ablators with the purpose of establishing an approximate analytical model capable of determining surface recession, temperature, and heat flux as well as in-depth temperature profiles. A detailed dimensional analysis of the melt-flow governing equations is performed for parameters applicable to high-enthalpy flows. Results of arc-jet flow experiments performed on NASA Reusable Surface Insulation materials of different densities and over a range of stagnation pressures and heat fluxes are discussed. A dimensionless correlation for melt run-offs is derived in terms of material and flow parameters; however, it is pointed out that the accuracy of the current data is sufficient to conclude the compliance with the model.

Henline, William D.↗

NASA NTRS1976

Measurements in the mixing region of a turbulent jet in a coflowing airstream

The mixing region of a turbulent jet is an important example of an intermittent turbulent shear flow. There are a great deal of interest in this region because of interest in jet noise and STOL aircraft which use upper surface blowing or externally blown flap configurations to increase lift. A detailed study of the one point statistical properties of a smoke laden jet was made using a combination of a laser velocimeter and a light scattering system. The jet, with a 14 to 1 contraction, was placed inside a wind tunnel where the ratio of the jet exit velocity to free stream was 5.1 to 1. All measurements are made for a jet Reynolds number of 22,600. Among the quantities measured are mean axial and radial velocities, axial and radial intensities, power spectra, mean smoke concentration, concentration intensities, concentration spectra, intermittencies and velocity-concentration correlations. The results are compared with hot-wire data where available.

Morton, J. B.↗

NASA NTRS1975

Mean flow characteristics for the oblique impingement of an axisymmetric jet

The oblique impingement of an axisymmetric jet has been investigated. A summary of the data and the analytical interpretations of the dominant mechanisms which influence the flow are reported. The major characteristics of the shallow angle oblique jet impingement flow field are: (1) minimal dynamic spreading as revealed by the surface pressure field, (2) pronounced kinematic spreading as revealed by the jet flow velocity field, (3) a pronounced upstream shift of the stagnation point from the maximum pressure point, (4) the production of streamwise vorticity by the impingement process.

Foss, J. F.↗

NASA NTRS2006

3-D GRMHD Simulations of Disk-Jet Coupling and Emission

We have performed a fully 3-D GRMHD simulation of jet formation from a thin accretion disk around a Schwarzschild black hole with a free-falling corona. The simulation results show that a bipolar jet is initially created. At later times, the accretion disk becomes thick and the jet fades resulting in a wind that is ejected from the surface of the thickened (torus-like) disk. This evolution of disk-jet coupling suggests that the jet fades with a thickened accretion disk. Recently we have developed two new codes: 3 -D GRMHD: RelAtivIStic magnetoHydrodynamica1 sImulatioN (RAISHIN) code constructed by modern high-resolution shock-capturing (HRSC) techniques and 3-D GRPIC code. We have calculated free-free and synchrotron emission from the disks and jet/outflows obtained from our GRMHD simulations using a fully covariant radiative transfer formulation.

Nishikawa, K.-I.↗

DOE OSTI2025

Toward Verification of RANS Simulations of the T-Tube Modular Divertor Using Large Eddy Simulations of Impinging Turbulent Plane Jets

Turbulent impinging jets have been proposed to cool high heat flux plasma-facing components such as the solid tungsten target plates of the divertor in long-pulse magnetic fusion energy reactors. In particular, the T-tube modular divertor, originally developed by the ARIES Team, consists of two concentric cylindrical tubes where helium flows through a slot in the inner tube, forming an approximately planar jet that impinges upon and cools the inner surface of the pressure boundary (namely, the outer tube) and the ~15-cm 2 plasma-facing W target. The objective of this work is to demonstrate that large eddy simulations (LESs) accurately simulate the thermal transport in canonical flows that comprise the cooling flow in the T-tube, as well as validate temperatures from LES with experimental measurements in a simplified T-tube geometry. Wall‑resolved LESs, validated by experimental data and verified by direct numerical simulations (DNSs), provide benchmark data for two canonical flows in the T‑tube, namely, planar impinging and wall jets, for Reynolds numbers Re B = 4 × 10 3 to 2 × 10 4 . Our LES results are within 4% to 12% root-mean-square error (RMSE) of surface Nusselt number distributions (Nu) from experiments and DNSs. The validated LES results are then used as the ground truth to evaluate four Reynolds‑averaged Navier-Stokes (RANS) turbulence closures, namely, the k‑ω SST, realizable k‑ε, GEKO, and γ‑SST models. The k‑ω SST model has the best overall performance in terms of heat transfer, giving surface Nu within 12% RMSE of the LES results for high‑ReB impinging jets and reduced overprediction in the wall‑jet region. The GEKO model with default constants has the next best performance, providing slightly better Nu predictions for low ReB impinging jets (versus k-ω SST) but worse overall performance over the full range of ReB studied here. The realizable k‑ε turbulence model significantly overestimates turbulence near the stagnation point, while the γ‑SST model suppresses near‑wall production, biasing the simulations toward simulating laminar surface heat transfer. Simulations of the simplified T‑tube show that LES and RANS simulations with the k‑ω SST model give nearly identical average heat transfer coefficients (HTCs) over the impingement surface. The realizable k‑ε model predicts significantly lower wall temperatures due to overestimation of HTC in the outlet flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1972

Wind-tunnel investigation at low speeds of a model of the Kestrel (XV-6A) vectored-trust V/STOL airplane

Longitudinal and lateral stability data were obtained with the model out of and in ground effect over a moving ground plane for a range of model angles of attack and sideslip at various thrust coefficients. These data were taken primarily at thrust coefficients which simulate transition speeds on the airplane between hover and 200 knots. Some data, however, represent the effect of thrust deflection at speeds up to 350 knots. Also presented are the effects of control-surface deflections and interference between the jets and free stream.

Margason, R. J.↗

NASA NTRS1973

Effect of gage size on the measurement of local heat flux

General formulas are derived for determining gage averaging errors of strip-type heat flux meters used in the measurement of one-dimensional heat flux distributions. In addition, a correction procedure is presented which allows a better estimate for the true value of the local heat flux. As an example of the technique, the formulas are applied to the cases of heat transfer to air slot jets impinging on flat and concave surfaces. It is shown that for many practical problems, the use of very small heat flux gages is often unnecessary.

Baumeister, K. J.↗

NASA NTRS1973

Aerodynamic characteristics of a large-scale model with a swept wing and a jet flap having an expandable duct

The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.

Aiken, T. N.↗

NASA NTRS1974

A review of air transport noise

Flight vehicles are characterized according to their manner of operation and type of propulsion system, and their associated sources of noise are identified. Available noise reduction technology as it relates to engine cycle design and to power plant component design is summarized. Such components as exhaust jets, fans, propellers, rotors, airflow-surface interactions, and reciprocating engine exhausts are discussed, along with their noise reduction potentials. Significant aircraft noise reductions are noted to have been accomplished by the application of available technology in support of noise certification rules. Improved analytical prediction methods, and well controlled validation experiments supported by advanced design aeroacoustic facilities, are required as a basis for an effective integrated systems approach to aircraft noise control.

Hubbard, H. H.↗

NASA NTRS1976

A theoretical investigation of over-wing-blowing aerodynamics

A theoretical method is established for determining the aerodynamic characteristics of over-wing-blowing configurations. The method accounts for both jet entrainment and jet interaction effects because of the differences in freestream and jet dynamic pressures and Mach numbers. The predicted lift increments agree well with available data. It is shown that the lift is underpredicted with entrainment effect alone when the jet is close to the wing surface.

Lan, C. E.↗

NASA NTRS1976

Oil-air mist lubrication for helicopter gearing

The applicability of a once-through oil mist system to the lubrication of helicopter spur gears was investigated and compared to conventional jet spray lubrication. In the mist lubrication mode, cooling air was supplied at 366K (200 F) to the out of mesh location of the gear sets. The mist air was also supplied at 366K (200 F) to the radial position mist nozzle at a constant rate of 0.0632 mol/s (3 SCFM) per nozzle. The lubricant contained in the mist air varied between 32 - 44 cc/hour. In the recirculating jet spray mode, the flow rate was varied between 1893 - 2650 cc/hour. Visual inspection revealed the jet spray mode produced a superior surface finish on the gear teeth but a thermal energy survey showed a 15 - 20% increase in heat generated. The gear tooth condition in the mist lubrication mode system could be improved if the cooling air and lubricant/air flow ratio were increased. The test gearbox and the procedure used are described.

Mcgrogan, F.↗

NASA NTRS1979

In situ oxygen conditioning of /001/ MgO thin film substrates for film growth studies by electron microscopy

It was found that the in situ treatment of 001-plane single-crystal films of MgO (prepared by epitaxial growth from the vapor phase) at high temperatures with a jet of oxygen will produce a surface that is almost equivalent, for epitaxial studies, to surfaces with the same orientation prepared by vacuum cleavage of bulk single crystals. The effectiveness of the process is demonstrated by its impact on the epitaxy of silver.

Moorhead, R. D.↗

NASA NTRS1979

An investigation of corner separation within a thrust augmenter having Coanda jets

The development of separation in corners of thrust augmentor wings having Coanda jets was investigated using hot film surface sensors and pressure transducers. Separation on the test augmentor began at a corner very close to the augmentor exit and then rapidly proceeded upstream. Measurements of the pressure fields in the corner region indicated that a modified form of the Stratford criterion could be used to predict the onset of separation. Testing was conducted over a range of nozzle pressure ratios, aspect ratios, diffuser angles, and designs of the boundary layer and Coanda nozzles.

Seiler, M. R.↗

NASA NTRS1980

Experimental Study of the Stability of Aircraft Fuels at Elevated Temperatures

An experimental study of fuel stability was conducted in an apparatus which simulated an aircraft gas turbine fuel system. Two fuels were tested: Jet A and Number 2 Home Heating oil. Jet A is an aircraft gas turbine fuel currently in wide use. No. 2HH was selected to represent the properties of future turbine fuels, particularly experimental Reference Broad Specification, which, under NASA sponsorship, was considered as a possible next-generation fuel. Tests were conducted with varying fuel flow rates, delivery pressures and fuel pretreatments (including preheating and deoxygenation). Simulator wall temperatures were varied between 422K and 672K at fuel flows of 0.022 to 0.22 Kg/sec. Coking rate was determined at four equally-spaced locations along the length of the simulator. Fuel samples were collected for infrared analysis. The dependence of coking rate in Jet A may be correlated with surface temperature via an activation energy of 9 to 10 kcal/mole, although the results indicate that both bulk fluid and surface temperature affect the rate of decomposition. As a consequence, flow rate, which controls bulk temperature, must also be considered. Taken together, these results suggest that the decomposition reactions are initiated on the surface and continue in the bulk fluid. The coking rate data for No. 2 HH oil are very highly temperature dependent above approximately 533K. This suggests that bulk phase reactions can become controlling in the formation of coke.

Vranos, A.↗

NASA NTRS1986

Powder Extinguishants for Jet-Fuel Fires

Mixtures of alkali metal dawsonite and metal halide show superior performance. In tests of new dry powder fire extinguishants, mixtures of potassium dawsonite with either stannous iodide or potassium iodide found effective for extinguishing jet-fuel fires on hot metal surfaces (up to 900 degrees C). Mixtures performed more effectively than either compound alone.

Altman, R. L.↗

NASA NTRS1987

Corrosion of SiC by Molten Salt

Advanced ceramic materials considered for wide range of applications as in gas turbine engines and heat exchangers. In such applications, materials may be in corrosive environments that include molten salts. Very corrosive to alloys. In order to determine extent of problem for ceramic materials, corrosion of SiC by molten salts studied in both jet fuel burners and laboratory furnaces. Surface of silicon carbide corroded by exposure to flame seeded with 4 parts per million of sodium. Strength of silicon carbide decreased by corrosion in flame and tube-furnace tests.

Jacobson, Nathan S.↗