SEARCH · Engineering Papers

Results for “Grain boundary structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Investigation of the fracture mechanism of Ti-5Al-2.5Sn at cryogenic temperatures

Fractography and metallographic sectioning were used to investigate the influence of microstructure on the fracture mechanism and fracture toughness (KIC) of normal interstitial and extra low interstitial (ELI) Ti-5Al-25Sn at 20 K (-423 F) and 77 K (-320 F). Plates of each grade were mill annealed at 815 C followed by either air or furnace cooling. These variations in composition and cooling rate resulted in differences in the volume fraction and internal structure of the dispersed beta phase and in the ordering of the alpha matrix. The ELI alloys were tougher than the normal interstitial plates. KIC of the furnace-cooled ELI plate was 25% lower than that of the air-cooled ELI material. Variations in cooling rate had no influence of KIC of the normal interstitial alloys. Fractography showed that a large portion of the fracture surfaces were covered with elongated dimples. Metallographic sections of specimens deformed at 77 K showed that these features form at the intersections of slip bands or deformation twins with grain or twin boundaries. Ordering and higher interstitial levels increase the local strain in slip bands resulting in void nucleation at lower macroscopic strains and lower KIC values.

Van Stone, R. H.↗

NASA NTRS2011

High temperature strain gages

A ceramic strain gage based on reactively sputtered indium-tin-oxide (ITO) thin films is used to monitor the structural integrity of components employed in aerospace propulsion systems operating at temperatures in excess of 1500.degree. C. A scanning electron microscopy (SEM) of the thick ITO sensors reveals a partially sintered microstructure comprising a contiguous network of submicron ITO particles with well defined necks and isolated nanoporosity. Densification of the ITO particles was retarded during high temperature exposure with nitrogen thus stabilizing the nanoporosity. ITO strain sensors were prepared by reactive sputtering in various nitrogen/oxygen/argon partial pressures to incorporate more nitrogen into the films. Under these conditions, sintering and densification of the ITO particles containing these nitrogen rich grain boundaries was retarded and a contiguous network of nano-sized ITO particles was established.

Gregory, Otto J.↗

NASA NTRS1985

Na2SO4 induced corrosion of nickel at high temperature

Sodium sulfate-induced corrosion of nickel was studied at 900 C as a function of oxygen partial pressure. For high O2 partial pressures, accelerated corrosion during the first few minutes occurred by rapid penetration of the melt along the metal grain boundaries. A mechanism is proposed to explain this phenomenon. Repetitive scale metal detachment was observed for corrosion in lower O2 partial pressures and during the later period of corrosion in higher O2 partial pressures. The effect of preoxidation on the hot corrosion has also been studied. An induction period is observed before the onset of rapid corrosion for the preoxidized samples; the onset of rapid corrosion is associated with sudden cracking of the scale. The length of the induction period for the preoxidized samples is a function of the length of preoxidation, and appears to be related to the structure of the oxide scale after the preoxidation treatment.

Misra, A. K.↗

DOE OSTI2020

The Role of Secondary Particle Structures in Surface Phase Transitions of Ni-Rich Cathodes

Nanometer-thick reconstruction layers on layered cathode surfaces have been widely observed on both pristine and cycled materials. However, the mechanisms of reconstruction and the role that these structures play in electrochemical performance are not fully understood. From a crystallographic perspective, such surface reconstruction layers result from cation site-mixing between Li and transition-metal ions, but it remains far from clear as to what the critical factors are that control such cation mixing for various cathode chemistries. In this paper, we report observations on surface transformations during cycling of a Ni-rich cathode-oxide that are governed by direct contact with the liquid electrolyte. Specifically, within a secondary particle, the three-dimensional hierarchical aggregate of primary particles leads to the formation of grain boundaries of different characteristics, including open grain boundaries that allow the permeation of liquid electrolyte, and closed grain boundaries that exclude liquid electrolyte penetration. Upon battery cycling, surfaces in direct contact with the liquid electrolyte showed a surface reconstruction layer while the surfaces that did not have contact with the electrolyte showed no such reconstructions. In addition, the critical role of oxygen in reconstruction of grain boundaries is demonstrated, and the unexpected oxygen depletion at twin boundaries result in severe phase transitions. The present work provides further insights into phase transitions at solid-solid and solid-liquid interfaces within secondary cathode particles and suggests strategies for mitigating surface/interfacial degradation.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Electronic Structure and Spin Correlations in Novel Magnetic Structures

The research has advanced understanding of the interrelation between the crystal structure and magnetism in several materials which are or can be of interest for the development of improved, specialized or more cost-effective permanent magnets, as well as in selected materials for biomedical and catalytic applications. Fundamental aspects of ferromagnetism were investigated for Mn-Ge, Co-V and Co-Ge nanoclusters and for melt-spun Co-Sn alloys. New solution-chemistry synthesis methods were designed and tested for Fe-Pt, Fe3C and Fe3O4 nanoparticles. Off-stoichiometric Laves phases in the Fe-Si-Zr, Fe-Nb and Fe-Ta systems, as well as Fe5(Si,Ge)B2 compounds were assessed as new rare-earth-free permanent magnet materials; all except the Fe-Si-Zr Laves phases were found to be promising enough to merit a further exploration. A new method for manufacturing rare-earth-free magnets based on the MnBi compound was developed; by purposely avoiding oxidation-sensitive fine single-crystalline powders, the new method yields magnets with a 50% larger energy storage capacity. Studies of rare-earth-lean permanent-magnet materials (lean compared to the currently predominant Nd-Fe-B materials) were focused on the tetragonal compound of the ThMn12 structure type and included both discovery and characterization of new formulations and exploration of new fabrication/processing techniques. Among the most significant achievements were successful preparation of a vanadium-lean SmFe11V compound, the first observation of thermomechanically induced texture in nanocrystalline Sm(Fe,V)12 alloys, and a breakthrough reduction-diffusion synthesis of Sm1-xZrx(Fe0.8Co0.2)11.2Ti0.8 single-crystal particles with a coercivity as high as 12.6 kOe. Several experiments aimed at improvement of the Nd-Fe-B magnet have also been undertaken including a five-fold increase of the coercivity through a grain-boundary diffusion treatment of a Nd10Fe84B6 nanocrystalline alloy.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Modeling the Impact of Grain Size on Corrosion Behavior of Ni-Based Alloys in Molten Chloride Salt via Cellular Automata

Molten chloride salts hold significant promise as both thermal transfer and storage media for next-generation concentrated solar power (CSP) systems. However, molten chlorides pose a considerable corrosion risk to structural materials, particularly Ni-based alloys. One approach to enhancing corrosion resistance is through the optimization of grain structure; however, it remains uncertain whether increasing or decreasing grain size enhances corrosion resistance. A cellular automata (CA) program was developed to evaluate the interplay between grain size and corrosion in Ni-based alloy. Our CA program tracks alloy composition, surface roughness, and thickness loss via a graphical user interface, displaying corrosion and diffusion status, and multiple user input cards for tuning the simulation. CA simulations of Inconel 625 indicate enhanced corrosion resistance with increased grain size, with passivating oxides offering limited protection. Additionally, the temporal evolution of alloy surface roughness demonstrates notable fluctuations, with abrupt increases attributed to corrosion along vertical grain boundaries and sudden decreases to grain detachment from the protective film.

Materials Science↗

NASA NTRS1991

Diffusion mechanisms in Ir-coated Re for high-temperature, radiation-cooled rocket thrusters

Materials used for radiation-cooled rocket thrusters must be capable of surviving under extreme conditions of high temperatures and oxidizing environments. Thruster chambers were developed using chemical-vapor-deposited (CVD) Re coated with CVD Ir on the inside surface which is exposed to hot combustion gases. Ir serves as an oxidation barrier protecting the Re which maintains structural integrity at high temperatures. In order to predict and extend the performance limits of these Ir-coated Re thrusters, the diffusion kinetics of CVD materials at temperature are studied. Thruster end ring sections were examined using electron microprobe analysis both before and after exposure to high temperature vacuum environments. The resulting elemental maps for Re, Ir, and Mo in the near-surface region allow identification of diffusion mechanisms operating at these temperatures. Line scans for Ir and Re were fit using a diffusion model to extract relevant diffusion constants. The fastest diffusion process is seen to be grain boundary diffusion with Re diffusing down grain boundaries in the Ir overlayer. The measured dependence of the diffusion rate on temperature will allow prediction of operating lifetimes for these thrusters.

Hamilton, J. C.↗

DOE OSTI2024

Response of 11 B enriched ZrB 2 ultra-high temperature ceramic to neutron irradiation at elevated temperatures

ZrB 2 , an ultra-high temperature ceramic (UHTC) is being considered for use in fusion reactor first-wall structures, yet its response to irradiation remains poorly understood. This study employed scanning/transmission electron microscopy (S/TEM), synchrotron X-ray diffraction (XRD), finite element calculations, and thermal property measurements to thoroughly investigate the neutron-irradiation effects on 11 B-enriched ZrB 2 . Neutron irradiations were conducted at 220 °C and 620 °C, with a neutron fluence of 2.2 × 10 25 neutron/m 2 (energy > 0.1 MeV), resulting in 3.9 dpa and 4200 appm He. The study revealed the unusual prevalence of prism loops and a > c anisotropic lattice swelling, likely linked to the low c/a ratio of ZrB 2 , leading to grain boundary microcracking. Reducing the grain sizes was effective in reducing intergranular cracking and macroscopic swelling. The observation of cavities in ZrB 2 irradiated at 620 °C, as opposed to 220 °C, prompts questions about the temperature at which vacancies in ZrB 2 become mobile, and the role of neutron absorption by 10 B in elevating irradiation temperatures. Isotopic enrichment in 11 B proves to be a viable strategy for mitigating helium production in transition-metal diborides, which is a critical consideration for nuclear applications. Irradiation-induced defects reduce the thermal diffusivity and conductivity of ZrB 2 by a factor of 4–9, which has important implications for its role as a plasma-facing material in fusion reactors that drive high heat fluxes through first-wall materials. Here, this comprehensive study lays the foundation for understanding ZrB 2 behavior under neutron irradiation and highlights important phenomena to consider for various material applications.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Additively manufactured novel Al-Cu-Sc-Zr alloy: Microstructure and mechanical properties

An in-depth understanding of microstructure and resultant properties is paramount in the design of a novel alloy system, especially for additive manufacturing (AM). The present investigation aims to characterize a prototypical AM Al alloy with great potential for structural applications. An Al-1.5Cu-0.8Sc-0.4Zr alloy designed using integrated computational material engineering was printed using the laser powder bed fusion AM process. This novel alloy shows promising combination of strength and ductility in as-built and peak-aged conditions. This improvement in the tensile properties is attributed to the presence of both coherent L1 2 Al 3 Sc/Al 3 (Sc,Zr) precipitates and Cu-rich regions. The microstructures were studied via extensive microscopy at different length scales using X-ray microscopy, scanning electron microscopy, and transmission electron microscopy. Fractography revealed that the columnar grain boundaries in as-built condition allow easy slip transfer as compared to the equiaxed grains, with the apex of the melt pool acting as the crack nucleation site. Furthermore, the peak aged condition resulted in improved strength while marginally sacrificing ductility due to precipitates decorating dislocations, grain boundaries and melt pool boundaries thus acting as obstacles to slip transfer.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Mechanical properties and strengthening mechanisms of cold sprayed Al-Mg alloys

This paper investigates the mechanical properties and strengthening mechanisms of cold sprayed Al-Mg alloys as a function of Mg content. Cold spray (CS) is a solid-state deposition process that can be used as a repair technique for structural components. However, the limited ductility of cold sprayed materials is an unsettled issue in CS community. Herein, reproducible, and significantly increased elongation to failure (∼15%) in as-deposited conditions is reported in CS Al-Mg binary alloys with low Mg content (≤ 2.5 wt%). Furthermore, reducing Mg content down to 2.5 wt% in CS Al-Mg binary alloys demonstrated comparable mechanical strength to its wrought counterparts. Strengthening mechanisms were analyzed in wrought and CS Al-Mg alloys based upon microstructural characteristics, such as grain size, Mg solute concentration, and dislocation density. A quantitative evaluation of yield strength revealed that grain boundary strengthening is predominant in CS Al-Mg alloys as compared with their wrought counterparts. When comparing among CS Al-Mg binary alloys of different compositions, Mg solute concentration, and dislocation density governed mechanical strength. In conclusion, the underlying mechanism for the variation of mechanical properties and strengthening mechanisms is discussed in terms of these microstructural characteristics.

Additive manufacturing↗

DOE OSTI2026

Thermal Stability and Ion Irradiation Response of Refined Grained V – 4Cr – 4Ti

Since the 1960’s, there has been interest in V-4Cr-4Ti and similar alloys as candidates for low activation structural materials for advanced nuclear reactors. V-4Cr-4Ti was produced using arc melting and subsequently subjected to large strain extrusion machining to produce a multimodal microstructure largely composed of nanocrystalline and ultrafine grain sizes. In-situ thermal stability of the multimodal V-4Cr-4Ti to 800 °C shows the formation of vanadium carbides with negligible grain growth. In-situ dual-beam 16 KeV He+ and 1 MeV Kr2+ ion irradiation performed at 700 °C to a final dose of ~5 displacements per atom show the formation of small He cavities well distributed throughout the system, with preferential clustering at grain boundaries. This work provides insight into how the increased fraction of grain boundaries affect the simultaneous dual beam ion irradiation response of multimodal V – 4 wt.% Cr – 4 wt.% Ti at elevated temperatures. Analysis of the cavities reveal an areal density of 0.024±0.007 cavities/nm2 and swelling of 0.236% after the dual-beam ion irradiation. Nanoindentation shows a ~50% increase in hardening after the ion irradiation at 700 °C.

TEM↗

DOE OSTI2023

Understanding process-microstructure-property relationships in laser powder bed fusion of non-spherical Ti-6Al-4V powder

Powder feedstock is a major cost driver in metal additive manufacturing (AM). Replacing the spherical powder with the cost-efficient non-spherical one can reduce the feedstock cost up to 50% and attract more interest to adopt AM in production and new alloy development. Here, for this paper, a comprehensive study was conducted to understand process-microstructure-property relationships in laser powder bed fusion of hydride-dehydride Ti-6Al-4V powder. We demonstrated that variation of laser scan speed had a significant impact on the grain structure, pore evolution and properties compared to laser power. Dynamic X-ray radiography showed that with decreasing scan speed at a constant laser power, a transition from conduction to keyhole mode laser processing occurred, in which a deeper melt pool at lower scan speed intensified texture. In other words, an increase in laser scan speed resulted in formation of the refined prior β grains with shape factor of ~5, lowering the anisotropy. Furthermore, the degree of variant selection was evaluated based on the analyzed texture as a function of laser power and scan speed. With increasing laser scan speed, the dominant α/α boundary type was altered from type 2 to 4 and the degree of variant selection was noticeably decreased. On the other hand, increasing laser power left the morphology of prior β grains, their size, and the dominant α/α boundary (type 4) unchanged, while the texture and anisotropy were intensified, and the degree of variant selection was slightly decreased. Finally, dependency of surface roughness and microhardness were discussed as a function of laser processing parameters.

variant selection↗

DOE OSTI2023

Development of bubble evolution model for new mechanistic transient fission gas release capability in BISON

This report summarizes efforts within NEAMS to investigate the mechanisms that govern fission gas behavior in UO 2 . In particular, the focus is on understanding how fission gas behavior causes transient fission gas release and fragmentation/pulverization of high burnup structure (HBS) in UO 2 . HBS forms in the periphery of the pellet where temperatures are relatively low. Previously, MD simulations were performed to determine the reaction energies for various Xe and U defects with bubbles, as a function of Xe to vacancy ratio or, equivalently, pressure. As had been shown in FY22, it was found that the unmodified version of the Simple Integrated Fission Gas Release and Swelling (SIFGRS) model within BISON greatly over-predicted the number gas atoms per vacancy in the bubbles in the outer rim of the pellet (a ratio of > 1 million). This was due to slow grain boundary vacancy diffusivity and not accounting for the pressure-dependent reaction energy for Xe interstitials with bubbles. The application of the pressure dependent reaction energies was able to restrict Xe to vacancy ratios to 2:1, which is far more realistic than those originally obtained from SIFGRS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1990

Elliptical flux vortices in polycrystalline YBa2Cu3O7

The formation of an Abrikosov flux vortex with its core axis perpendicular to an anisotropic (a-c or b-c) plane in YBa2Cu3O7 requires only 1/10 of the energy required by the formation of a vortex with its core axis perpendicular to an isotropic (a-b) plane. It is not unusual for 18 to 35 percent of shake and bake bulk YBa2Cu3O7 to consist of empty pockets or voids inside the material. Studies estimate that 75 percent of the internal grain boundaries contain a-b planes. If many of the a-b planes are incident upon other grains, then many of the a-c and/or b-c planes must be incident on the voids. Evidently there are a large number of exposed anisotropic planes inside the bulk material. This condition is conducive to the formation of vortices that are perpendicular to the anisotropic planes. The magnetic flux density around such a vortex is constant along contour lines that are elliptical in shape, while the circulating supercurrent density must vary in magnitude along the same contour lines. The impact of this elliptical structure on the possibility of a Kosterlitz-Thouless type phase transition as the bulk material goes from superconducting to normal conducting is discussed. Implications with regard to the excess low frequency electrical noise that occurs at the temperature induced transition are also examined.

Hickman, H.↗

DOE OSTI2024

Microstructural Coarsening Kinetics and Mechanical Property Changes in Long-Term Aged Sn–Pb–Sb Solder Joints

Tin-lead-antimony (50Sn–47Pb–3Sb wt.%) soldered assemblies were mechanically tested approximately 30 years after initial production and found to have solder joints of reduced strength. The microstructure of this solder alloy exhibits a ternary eutectic structure with Sn-rich, Pb-rich, and SnSb phases. Accelerated aging was performed to evaluate solder microstructural coarsening and associated strength of laboratory solder joints to correlate these properties to the “naturally aged” solder joints. Isothermal aging was conducted at room temperature, 55, 70, 100, and 135 °C and aging times that ranged from 0.1 to 365 days. The coarsening kinetics of the Pb-rich phase were determined through optical microscopy and image analysis methods established in previous studies on binary Sn–Pb solder. A kinetic equation was developed with time exponent n of 0.43 and activation energy of 24000 J/mol, suggesting grain boundary diffusion or other fast diffusion pathways controlling the microstructural evolution. Compression testing and Vickers microhardness showed significant strength loss within the first 20–30 days after soldering; then, the microstructure and mechanical properties changed more slowly over long periods of time. Further, by combining accelerated aging data and the microstructure-based kinetics, strength predictions were made that match well with the properties of the actual soldered assemblies naturally aged for 30 years. However, aging at the highest temperature of 135 °C produced anomalous behavior suggesting that extraneous aging mechanisms are active. Therefore, data obtained at this temperature or higher should not be used. Overall, the combined microstructural and mechanical property methods used in this study confirmed that the observed reduction in strength of ~ 30-year-old solder joints can be accounted for by the microstructural coarsening that takes place during long-term solid-state aging.

36 MATERIALS SCIENCE↗

DOE OSTI2024

An Engineering Approach for Weld Creep Lifetime Assessment Based on Local Property Measurement

The localized creep failure in the heat-affected zone (HAZ) of Grade 91 steel weldments has been identified as one of the most important factors causing significantly shortened service lifetime and structural integrity issues of welded components in advanced fossil and nuclear power plants. To conduct a reliable creep lifetime assessment, a new engineering assessment approach has been developed by incorporating the experimentally determined local properties of the heterogeneous HAZ. By creep testing a purposely simulated HAZ specimen with in situ digital image correlation (DIC) technique, the highly gradient creep properties across the HAZ of Grade 91 steel was quantitatively measured. A physical creep cavitation constitutive model was proposed to investigate the local creep deformation and damage accumulation within the heterogeneous HAZ, which takes into account the nucleation of creep cavities and their growth by both grain boundary diffusion and creep deformation. The relationship among the local material property, creep strain accumulation, and evolution characteristic of creep cavities was established. The approach was then utilized to investigate the creep response and subsequent life for an ex-service 9% Cr steel weldment by incorporating the effects of pre-existing damages which developed and accumulated during long-term services. The predicted results exhibited quantitative agreement with the DIC measurement in terms of both nominal/local creep deformation as well as the subsequent life under the test conditions at 650 and 80 MPa.

Zhang, Wei↗

DOE OSTI2020

An Overview of Neutron Irradiated SiC Layer Behavior using Micro-and Nano-Characterization Techniques

The complexity of fission product distribution and composition within the SiC layer of tristructural isotropic (TRISO) coated particles, irradiation effects on the SiC structure as well as the variable nature of metallic fission product release, has led to the exploration of multiple micro- and nano-characterization techniques. The fine scale of the fission product precipitates necessitates unique learnings and application of electron microscopic techniques with irradiated fuel during the Advanced Gas Reactor (AGR)-1 experiment analysis. A summarized discussion on the specific advanced techniques with associated method development for TRISO coated particles is provided followed by the down selected techniques currently considered to provide the highest impact. Techniques considered are electron probe micro-analyzer (EPMA), scanning transmission electron microscopy (STEM), and Precession electron diffraction (PED). SiC grain boundary characteristics are evaluated due to the mobility of specific fission products through grain boundaries. PED was performed for understanding the role of grain boundary character on fission product transport. One set of comparative analyses between AGR-1 and AGR-2 particles leads to a finding that the AGR-1, high-Ag-retention particle, had statistically more coincidence site lattice (CSL)-related grain boundaries (but fewer low-angle grain boundaries), compared to the AGR-2 particle. This implies that CSL-related grain boundaries may have a direct influence on Ag retention. However, precipitates were found on a relatively small fraction of CSL-related grain boundaries in both particles. In another set of comparison between AGR-1 and AGR-2 particles that were subjected to safety testing, there is significant differences in average SiC grain boundary distributions, but the fission product distributions on these grain boundaries are very similar.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Micro- and Nano-techniques for the Study of Fission Product Precipitation in SiC Layer

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗