Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GAN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Semiconductor Thermal and Electrical Properties Decoupled by Localized Phonon Resonances

Abstract Thermoelectric materials convert heat into electricity through thermally driven charge transport in solids or vice versa for cooling. To compete with conventional energy‐conversion technologies, a thermoelectric material must possess the properties of both an electrical conductor and a thermal insulator. However, these properties are normally mutually exclusive because of the interconnection between scattering mechanisms for charge carriers and phonons. Recent theoretical investigations on sub‐device scales have revealed that nanopillars attached to a membrane exhibit a multitude of local phonon resonances, spanning the full spectrum, that couple with the heat‐carrying phonons in the membrane and cause a reduction in the in‐plane thermal conductivity, with no expected change in the electrical properties because the nanopillars are outside the pathway of voltage generation and charge transport. Here this effect is demonstrated experimentally for the first time by investigating device‐scale suspended silicon membranes with GaN nanopillars grown on the surface. The nanopillars cause up to 21% reduction in the thermal conductivity while the power factor remains unaffected, thus demonstrating an unprecedented decoupling in the semiconductor's thermoelectric properties. The measured thermal conductivity behavior for coalesced nanopillars and corresponding lattice‐dynamics calculations provide evidence that the reductions are mechanistically tied to the phonon resonances. This finding paves the way for high‐efficiency solid‐state energy recovery and cooling.

Spann, Bryan T.↗
DOE OSTI2024

Nonequivalent Atomic Vibrations at Interfaces in a Polar Superlattice

In heterostructures made from polar materials, e.g., AlN–GaN–AlN, the nonequivalence of the two interfaces is long recognized as a critical aspect of their electronic properties; in that, they host different 2D carrier gases. Interfaces play an important role in the vibrational properties of materials, where interface states enhance thermal conductivity and can generate unique infrared-optical activity. The nonequivalence of the corresponding interface atomic vibrations, however, is not investigated so far due to a lack of experimental techniques with both high spatial and high spectral resolution. Herein, the nonequivalence of AlN–(Al 0.65 Ga 0.35 )N and (Al 0.65 Ga 0.35 )N–AlN interface vibrations is experimentally demonstrated using monochromated electron energy-loss spectroscopy in the scanning transmission electron microscope (STEM-EELS) and density-functional-theory (DFT) calculations are employed to gain insights in the physical origins of observations. It is demonstrated that STEM-EELS possesses sensitivity to the displacement vector of the vibrational modes as well as the frequency, which is as critical to understanding vibrations as polarization in optical spectroscopies. The combination enables direct mapping of the nonequivalent interface phonons between materials with different phonon polarizations. Furthermore, the results demonstrate the capacity to carefully assess the vibrational properties of complex heterostructures where interface states dominate the functional properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D‐Mapping and Manipulation of Photocurrent in an Optoelectronic Diamond Device

Abstract Establishing connections between material impurities and charge transport properties in emerging electronic and quantum materials, such as wide‐bandgap semiconductors, demands new diagnostic methods tailored to these unique systems. Many such materials host optically‐active defect centers which offer a powerful in situ characterization system, but one that typically relies on the weak spin‐electric field coupling to measure electronic phenomena. In this work, charge‐state sensitive optical microscopy is combined with photoelectric detection of an array of nitrogen‐vacancy (NV) centers to directly image the flow of charge carriers inside a diamond optoelectronic device, in 3D and with temporal resolution. Optical control is used to change the charge state of background impurities inside the diamond on‐demand, resulting in drastically different current flow such as filamentary channels nucleating from specific, defective regions of the device. Conducting channels that control carrier flow, key steps toward optically reconfigurable, wide‐bandgap optoelectronics are then engineered using light. This work might be extended to probe other wide‐bandgap semiconductors (SiC, GaN) relevant to present and emerging electronic and quantum technologies.

Wood, Alexander A.↗
DOE OSTI2020

Anharmonic multi-phonon nonradiative transition: An ab initio calculation approach

Nonradiative carrier recombinations at deep centers in semiconductors are of great importance for both fundamental physics and device engineering. Here, we provide a revised analysis of Huang’s original nonradiative multi-phonon (NMP) theory with ab initio calculations. First, we confirmed at the first-principles level that Huang’s concise formula gives the same results as the matrix-based formula, and that Huang’s high-temperature formula provides an analytical expression for the coupling constant in Marcus theory. Secondly, we correct for anharmonic effects by taking into account local phonon-mode variations for different charge states of a defect. The corrected capture rates for defects in GaN and SiC agree well with experiments.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Parameters, Properties, and Process: Conditional Neural Generation of Realistic SEM Imagery Toward ML-Assisted Advanced Manufacturing

Abstract The research and development cycle of advanced manufacturing processes traditionally requires a large investment of time and resources. Experiments can be expensive and are hence conducted on relatively small scales. This poses problems for typically data-hungry machine learning tools which could otherwise expedite the development cycle. We build upon prior work by applying conditional generative adversarial networks (GANs) to scanning electron microscope (SEM) imagery from an emerging advanced manufacturing process, shear-assisted processing and extrusion (ShAPE). We generate realistic images conditioned on temper and either experimental parameters or material properties. In doing so, we are able to integrate machine learning into the development cycle, by allowing a user to immediately visualize the microstructure that would arise from particular process parameters or properties. This work forms a technical backbone for a fundamentally new approach for understanding manufacturing processes in the absence of first-principle models. By characterizing microstructure from a topological perspective, we are able to evaluate our models’ ability to capture the breadth and diversity of experimental scanning electron microscope (SEM) samples. Our method is successful in capturing the visual and general microstructural features arising from the considered process, with analysis highlighting directions to further improve the topological realism of our synthetic imagery.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Leveraging generative AI for urban digital twins: a scoping review on the autonomous generation of urban data, scenarios, designs, and 3D city models for smart city advancement

The digital transformation of modern cities by integrating advanced information, communication, and computing technologies has marked the epoch of data-driven smart city applications for efficient and sustainable urban management. Despite their effectiveness, these applications often rely on massive amounts of high-dimensional and multi-domain data for monitoring and characterizing different urban sub-systems, presenting challenges in application areas that are limited by data quality and availability, as well as costly efforts for generating urban scenarios and design alternatives. As an emerging research area in deep learning, Generative Artificial Intelligence (GenAI) models have demonstrated their unique values in content generation. This paper aims to explore the innovative integration of GenAI techniques and urban digital twins to address challenges in the planning and management of built environments with focuses on various urban sub-systems, such as transportation, energy, water, and building and infrastructure. The survey starts with the introduction of cutting-edge generative AI models, such as the Generative Adversarial Networks (GAN), Variational Autoencoders (VAEs), Generative Pre-trained Transformer (GPT), followed by a scoping review of the existing urban science applications that leverage the intelligent and autonomous capability of these techniques to facilitate the research, operations, and management of critical urban subsystems, as well as the holistic planning and design of the built environment. Based on the review, we discuss potential opportunities and technical strategies that integrate GenAI models into the next-generation urban digital twins for more intelligent, scalable, and automated smart city development and management.

3D city modeling↗
DOE OSTI2024

STSR-INR: Spatiotemporal super-resolution for multivariate time-varying volumetric data via implicit neural representation

Implicit neural representation (INR) has surfaced as a promising direction for solving different scientific visualization tasks due to its continuous representation and flexible input and output settings. We present STSR-INR, an INR solution for generating simultaneous spatiotemporal super-resolution for multivariate time-varying volumetric data. Inheriting the benefits of the INR-based approach, STSR-INR supports unsupervised learning and permits data upscaling with arbitrary spatial and temporal scale factors. Unlike existing GAN- or INR-based super-resolution methods, STSR-INR focuses on tackling variables or ensembles and enabling joint training across datasets of various spatiotemporal resolutions. Here we achieve this capability via a variable embedding scheme that learns latent vectors for different variables. In conjunction with a modulated structure in the network design, we employ a variational auto-decoder to optimize the learnable latent vectors to enable latent-space interpolation. To combat the slow training of INR, we leverage a multi-head strategy to improve training and inference speed with significant speedup. We demonstrate the effectiveness of STSR-INR with multiple scalar field datasets and compare it with conventional tricubic+linear interpolation and state-of-the-art deep-learning-based solutions (STNet and CoordNet).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

X-ray topography characterization of gallium nitride substrates for power device development

Gallium nitride substrates grown by the hydride vapor phase epitaxy (HVPE) method using a patterned growth process have been characterized by synchrotron monochromatic beam X-ray topography in the grazing incidence geometry. Images reveal a starkly heterogeneous distribution of dislocations with areas as large as 0 3 mm 2 containing threading dislocation densities below 10 3 cm -2 in between a grid of strain centers with higher threading dislocation densities (> 10 4 cm -2 ). Basal plane dislocation densities in these areas are as low as 104 cm -2 . By comparing the recorded images of dislocations with ray tracing simulations of expected dislocations in GaN, the Burgers vectors of the dislocations have been determined. The distribution of threading screw/mixed dislocations (TSDs/TMDs), threading edge dislocations (TEDs) and basal plane dislocations (BPDs) is discussed with implications for fabrication of power devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Role of V-defect density on the performance of III-nitride green LEDs on sapphire substrates

In this paper, we experimentally investigated the role of V-defect density on the performance of green III-nitride LEDs grown on sapphire substrates by metalorganic chemical vapor deposition. We systematically varied the threading dislocation (TD) density from 4 × 10 8 to 1 × 10 9 cm -2 by changing the V/III ratio during initial high temperature GaN growth. A 30-period InGaN/GaN superlattice promoted V-defect formation and growth at TDs, where the density of V-defects was correlated to the TD density. By interrupting the LED growth and examining the surface of the active region, we quantified the average size and density of V-defects. In a series of LEDs, we measured a systematic decrease in forward voltage (V F ) with V-defect density. At a V-defect density of 5.0 × 10 8 cm -2 and TD density of 1 × 10 9 cm -2 , green LED devices were demonstrated with λ = 523 nm and V F = 2.94 V at 20 A cm -2 . These results highlight the potential of using V-defect engineering to achieve low V F long wavelength LEDs on sapphire substrates, where opening of remaining threading dislocations into V-defects presents an opportunity for further V F reduction.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Status and new features of the topography beamline 1-BM after the Advanced Photon Source upgrade

The beamline 1-BM of the Advanced Photon Source (APS), a bending-magnet beamline with an effective X-ray beam size of ~100×4 mm2, has relatively comprehensive synchrotron topography and rocking curve imaging capabilities for characterization of crystals (particularly wide-bandgap semiconductors SiC, AlN, GaN, Ga2O3 etc). It is equipped with a white-beam topography stage for imaging large wafers up to 8 inches. It also has a double-crystal setup, of which the second stage can be used for monochromatic-beam topography. The first stage has different beam conditioners in the grazing-incidence geometry that can expand the vertical beam size from 4 to ~100 mm for double-crystal rocking curve imaging when it is combined with the second stage. Recently APS has been upgraded to a modern 4th-generation light source, and 1-BM has been recommissioned to its normal operation for general users with better performance. The upgraded APS leads to new features at 1-BM. The much smaller source size and higher X-ray coherence significantly improve the image resolution and contrast. The higher flux and brightness of the new source reduce exposure time, which mitigates the mechanical drifting and vibration issues. Here the main capabilities and status of 1-BM together with these new features are introduced.

X-ray topography↗
DOE OSTI2025

A high-throughput approach for statistical process optimization in Laser Powder Bed Fusion

Process variability is inherent in metal additive manufacturing (AM). However, it is often overlooked in process optimization frameworks, constraining the understanding of process uncertainties and their influence on parameter selection. To address this, we present an integrated framework that combines high-throughput single-track experiments, GAN-based melt pool geometry extraction, robust statistical and machine learning modeling, and uncertainty-quantified process mapping. Process variability is characterized through single-track melt pool behaviors, and its influence on defect formation is systematically quantified to enable statistically guided process parameter optimization. This approach is demonstrated on Laser Powder Bed Fusion (L-PBF) of stainless steel 316L, effectively capturing the interplay between process parameters, melt pool variability, and defect probability. By integrating uncertainty quantification into process optimization, this study provides a structured methodology for addressing variability challenges in AM quality control, ultimately contributing to enhanced manufacturing reliability.

Laser Powder Bed Fusion↗
DOE OSTI2024

Microscopy modality transfer of steel microstructures: Inferring scanning electron micrographs from optical microscopy using generative AI

Scanning electron microscopy (SEM) is resource intensive, which limits its throughput in some applications. As an alternative, we propose applying computer vision and machine learning to generate high-quality synthetic SEM micrographs from micrographs obtained using light optical microscopy (LOM). Working with a correlated LOM/SEM dataset of dual-phase steel images, we test generative models of various architectures, including encoder-decoder networks, generative adversarial networks (GANs), and diffusion-based models. We find that the diffusion models significantly outperform other methods on both qualitative and quantitative assessments, while preserving key metallurgical meaning. This work establishes diffusion as the state-of-the-art for microscopy modality transfer and demonstrates the potential of AI-powered microscopy to enhance LOM with micron scale structural recreation.

Computer vision↗
DOE OSTI2022

Explainable machine learning of the underlying physics of high-energy particle collisions

We present an implementation of an explainable and physics-aware machine learning model capable of inferring the underlying physics of high-energy particle collisions using the information encoded in the energy-momentum four-vectors of the final state particles. We demonstrate the proof-of-concept of our White Box AI approach using a Generative Adversarial Network (GAN) which learns from a DGLAP-based parton shower Monte Carlo event generator. The constrained generator network architecture mimics the structure of a parton shower exhibiting similarities with Recurrent Neural Networks (RNNs). We show, for the first time, that our approach leads to a network that is able to learn not only the final distribution of particles, but also the underlying parton branching mechanism, i.e. the Altarelli-Parisi splitting function, the ordering variable of the shower, and the scaling behavior. While the current work is focused on perturbative physics of the parton shower, we foresee a broad range of applications of our framework to areas that are currently difficult to address from first principles in QCD. Examples include nonperturbative and collective effects, factorization breaking and the modification of the parton shower in heavy-ion, and electron-nucleus collisions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Influence of Polymorphism on the Electronic Structure of Ga 2 O 3

The search for new wide-band-gap materials is intensifying to satisfy the need for more advanced and energy-efficient power electronic devices. Ga 2 O 3 has emerged as an alternative to SiC and GaN, sparking a renewed interest in its fundamental properties beyond the main β-phase. Here, three polymorphs of Ga 2 O 3 , α, β, and ε, are investigated using X-ray diffraction, X-ray photoelectron and absorption spectroscopy, and ab initio theoretical approaches to gain insights into their structure–electronic structure relationships. Valence and conduction electronic structure as well as semicore and core states are probed, providing a complete picture of the influence of local coordination environments on the electronic structure. State-of-the-art electronic structure theory, including all-electron density functional theory and many-body perturbation theory, provides detailed understanding of the spectroscopic results. The calculated spectra provide very accurate descriptions of all experimental spectra and additionally illuminate the origin of observed spectral features. This paper provides a strong basis for the exploration of the Ga 2 O 3 polymorphs as materials at the heart of future electronic device generations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Wide Band Gap Chalcogenide Semiconductors

Wide band gap semiconductors are essential for today’s electronic devices and energy applications because of their high optical transparency, controllable carrier concentration, and tunable electrical conductivity. The most intensively investigated wide band gap semiconductors are transparent conductive oxides (TCOs), such as tin-doped indium oxide (ITO) and amorphous In–Ga–Zn–O (IGZO), used in displays and solar cells, carbides (e.g., SiC) and nitrides (e.g., GaN) used in power electronics, and emerging halides (e.g., γ-CuI) and 2D electronic materials (e.g., graphene) used in various optoelectronic devices. Compared to these prominent materials families, chalcogen-based (Ch = S, Se, Te) wide band gap semiconductors are less heavily investigated but stand out because of their propensity for p-type doping, high mobilities, high valence band positions (i.e., low ionization potentials), and broad applications in electronic devices such as CdTe solar cells. This manuscript provides a review of wide band gap chalcogenide semiconductors. First, we outline general materials design parameters of high performing transparent semiconductors, as well as the theoretical and experimental underpinnings of the corresponding research methods. We proceed to summarize progress in wide band gap (EG > 2 eV) chalcogenide materials—namely, II–VI MCh binaries, CuMCh 2 chalcopyrites, Cu 3 MCh 4 sulvanites, mixed-anion layered CuMCh(O,F), and 2D materials—and discuss computational predictions of potential new candidates in this family, highlighting their optical and electrical properties. Then, we finally review applications—for example, photovoltaic and photoelectrochemical solar cells, transistors, and light emitting diodes—that employ wide band gap chalcogenides as either an active or passive layer. Overall, by examining, categorizing, and discussing prospective directions in wide band gap chalcogenides, this Review aims to inspire continued research on this emerging class of transparent semiconductors and thereby enable future innovations for optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Gate-Tunable Semiconductor Heterojunctions from 2D/3D van der Waals Interfaces

Van der Waals (vdW) semiconductors are attractive for highly scaled devices and heterogeneous integration since they can be isolated into self-passivated, two-dimensional (2D) layers that enable superior electrostatic control. These attributes have led to numerous demonstrations of field-effect devices ranging from transistors to triodes. By exploiting the controlled, substitutional doping schemes in covalently-bonded, three-dimensional (3D) semiconductors and the passivated surfaces of 2D semiconductors, one can construct devices that can exceed performance metrics of “all-2D” vdW heterojunctions. Here, we demonstrate, 2D/3D semiconductor heterojunctions using MoS2 as the prototypical 2D semiconductor laid upon Si and GaN as the 3D semiconductor layers. By tuning the Fermi levels in MoS2, we demonstrate devices that concurrently exhibit over seven orders of magnitude modulation in rectification ratios and conductance. Our results further suggest that the interface quality does not necessarily affect Fermi-level tuning at the junction opening up possibilities for novel 2D/3D heterojunction device architectures

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Single-Atom-Resolved Vibrational Spectroscopy of a Dislocation

Dislocations in III-nitride semiconductors impede heat transport, leading to localized overheating, which severely limits the performance and reliability of optoelectronic and power devices. Current research on phonon–dislocation interactions primarily addresses bulk materials, focusing on the average effects at specific dislocation densities. However, phonon resistance from dislocation scattering arises from both short-range core interactions and long-range strain field interactions, which remain largely unexplored. Here, in this study, electron energy-loss spectroscopy is used to investigate a GaN dislocation. Vibrational modes localized on specific core atoms are revealed, reflecting short-range interactions. Additionally, phonon energy shifts driven by strain fields surrounding the dislocation are observed, reflecting long-range interactions. Ab initio calculations support these findings and draw out additional details. This work establishes a paradigm for probing defect-induced phonon scattering at the single-atom level, revealing how dislocations affect phonon behavior through atomic reconstruction and strain engineering, thus offering insights for designing improved material functionalities.

III-nitride semiconductors↗
DOE OSTI2020

Selective-Area Remote Epitaxy of ZnO Microrods Using Multilayer–Monolayer-Patterned Graphene for Transferable and Flexible Device Fabrications

Here, selective-area remote epitaxy (SA-REpi) is demonstrated for fabricating mechanically releasable position-controlled ZnO microrod (MR) arrays from donor wafers in an arrayed form. Intaglio-patterned graphene, consisting of basal single-layer graphene (SLG) overlayered with multilayer graphene (MLG) patterned with perforated holes, is transferred onto a GaN/Al 2 O 3 wafer on which the hydrothermal synthesis is performed for growing ZnO MRs. The basal SLG area exposed through the MLG pattern yields ZnO MRs, whereas the MLG plateau inhibits the growth. The noncovalent remote epitaxial heterointerface enables the release of the MR overlayer in the arrayed form, and the original source wafer is refurbished for reproducibly repeating the SA-REpi. Density-functional theory calculations suggest that localized surface charge density is induced on the surface of SLG by the underlying GaN across ultrathin SLG, which possibly provides a driving force for precursor adatoms and the following remote epitaxy of ZnO. In contrast, the induction of the charge density redistribution does not clearly occur through MLG; so, that keeps the surface of MLG nearly charge-neutral. The diameter and spacing of ZnO MRs are controlled in a designed way by changing the pattern geometries. High-resolution scanning transmission electron microscopy reveals the remote heteroepitaxial relationship at an atomic level. The remote epitaxy is expected to provide an ideal platform to transfer the addressable spatial arrays of nano- or micro-architecture semiconductor components to arbitrary target surfaces directly after the growth without the assembly procedures.

36 MATERIALS SCIENCE↗