Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Frequency modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

The northern Utah satellite (NUSAT) communications link

During the planning Stages of the NUSAT satellite, an obvious issue to be discussed was the method of communications to be used. The frequencies would have to be high enough to pass through the atmosphere relatively unattenuated but low enough that antennas and transmission lines would not be so critical in length and properties that unexperienced students would have difficulty with handling them. In conversations with the Federal Communications Commission (FCC) in Washington D.C., the frequencies of 450.000 MHz and 137.900 MHz were decided upon and applied for licensing. The 450.000 MHt up-link is used on a "non-interference" basis to control the satellite while the 137.900 MHz frequency down-links data from the satellite. A reasonable amount of time was spent discussing the mods of transmission to be used in communication with the satellite. Representatives of the amateur radio satellite organization, AMSAT, were contacted for ides. This organization seems to favor AM types of emissions such as CW to control their OSCAR series of satellites and also the current Phase 111 unit. NUSAT personnel felt, however, that there would be merit in the improved signal to noise ratio usually obtained in an FM mode. Doppler shift of the transmitted information on the NUSAT also had to be considered. The final decision WBS to use Audio Frequency Shift Keying (AFSK) modulated on an FM carrier. In this mode the audio tones used would not shift frequency with Doppler - only the carrier would shift in frequency. If necessary, the receivers could be fitted with a form of AFC control or simply have enough bandwidth to handle the Doppler shift with an acceptable increase in noise.

Lee Barrett↗

Solar Irradiance Variability, Influenced by r Modes

A spectrum of the four-decade solar irradiance record has a prominent cluster of power for periodicities near 1 yr. Correlating irradiance with a bandpass filter showed that periodicity values were not constant, but varied sinusoidally with each cycle lasting 14 ± 1 yr. The large modulation amplitude makes solar frequencies ≥1 yr(exp −1) hard to detect at the solar surface. After removing the modulation, a Lomb–Scargle spectrum exposed two true periodicities: 1.006 and 0.920 yr. They are interpreted as the synodic rotation periods of r modes of lowest angular degree (ℓ = 1). The first propagates in the stable interior and the second in the convective envelope perturbed by its several flow fields. The rotational beat period of the two modes is about 10.9 yr. This is close to the average length of a solar cycle and possibly controls this average. The 1.006 yr periodicity dominates most of the filtered irradiance record but an abrupt change to about 0.8 yr occurs in mid-2010. Also found was evidence for higher-degree r modes (ℓ = 2 to 8) and a curious sawtooth modulation with a recurrence period of 2.6 yr.

Wolff, Charles L.↗

Signal simulator model A-111

A signal simulator designed to function as a signal source for Doppler tracking high data rate receivers is described. The simulator produces modulated signals whose carrier frequency can be varied between 200 and 900 MHz at rates greater than 20 MHz/sec. The modulation is phase shift keying with data rate up to 300 megabits per second.

Flattau, T.↗

Two-frequency laser-induced fluorescence technique for rapid velocity-field measurements in gas flows

A technique is presented for measurements of two-dimensional velocity fields in gas flows. The single-mode frequency of an argon-ion laser is fixed in the wing of an absorption line of iodine molecules that are seeded at low level in the flow of interest. The emitted fluorescence is detected with an image-intensified 100 x 100 photodiode-array camera. two pairs of counterpropagating laser sheets sequentially probe the flow to determine two velocity components. The frequency in one pair is shifted with respect to the other by an acousto-optic modulator. This two-frequency scheme eliminates the need to determine the slope of the line externally and offers the potential for combined pressure and velocity-field measurements.

Hiller, B.↗

Pseudomorphic InGaAs/AlGaAs modulation-doped FET's with reduced low-frequency noise and thermally stable performance

A high-performance MODFET structure grown by MBE with the incorporation of a single quantum well In(0.15)Ga(0.85)As layer for the transport of two-dimensional electron gas has been critically examined for its thermal stability at 80 K and low-frequency noise form 0.01 to 10 to the 8th Hz. Experimental results indicate that the behavior of this device in both these respects is much superior when compared with the same behavior of conventional MODFETs. A maximum low-field carrier mobility of 29,000 sq cm/s at 80 K and an average carrier saturation velocity of 2 x 10 to the 7th cm/s at 300 K in a 1-micron gate device clearly indicate that the quality of the pseudomorphic quantum well (InGaAs) layer is either comparable or better than that of the usual GaAs buffer layer. The deep level spectra, obtained through photo-FET measurements, and the low-frequency noise spectra at different temperatures obtained for the new pseudomorphic and conventional MODFET's have clearly indicated that contributions from various deep levels present in the new structure are significantly reduced.

Liu, Shih-Ming↗

In-Line Electromagnetic Actuator for Fuel Modulation

An in-line electromagnetic actuator with normally-open configuration has been developed for the purpose of exploring its application as a fuel modulator for the active control of combustor thermo-acoustic instabilities. The actuator is based on the spring-coil-plunger mechanism with the plunger designed to be suspended by crossed cantilever beam springs. Operational specification was set for a 1000 psi maximum inlet fuel pressure and modulation for a broad frequency bandwidth that encompasses frequencies that are typically associated with combustor thermo-acoustic instabilities. Various test results demonstrated fuel modulation up to 1200 Hz for coil excitation voltage between 2.3 and 4.6 V and current between 16 and 48 mA, respectively. The initial goal of this work was to demonstrate fuel modulation based on the concept of a normally-open fuel modulator with tethered plunger displacement.

Actuator↗

In-Line Electromagnetic Actuator for Fuel Modulation

An in-line electromagnetic actuator with normally-open configuration has been developed for the purpose of exploring its application as a fuel modulator for the active control of combustor thermo-acoustic instabilities. The actuator is based on the spring-coil-plunger mechanism with the plunger designed to be suspended by crossed cantilever beam springs. Operational specification was set for a 1000 psi maximum inlet fuel pressure and modulation for a broad frequency bandwidth that encompasses frequencies that are typically associated with combustor thermo-acoustic instabilities. Various test results demonstrated fuel modulation up to 1200 Hz for coil excitation voltage between 2.3 and 4.6 V and current between 16 and 48 mA, respectively. The initial goal of this work was to demonstrate fuel modulation based on the concept of a normally-open fuel modulator with tethered plunger displacement.

Okojie, Robert S.↗

Goldstone Solar System Radar Waveform Generator

Due to distances and relative motions among the transmitter, target object, and receiver, the time-base between any transmitted and received signal will undergo distortion. Pre-distortion of the transmitted signal to compensate for this time-base distortion allows reception of an undistorted signal. In most radar applications, an arbitrary waveform generator (AWG) would be used to store the pre-calculated waveform and then play back this waveform during transmission. The Goldstone Solar System Radar (GSSR), however, has transmission durations that exceed the available memory storage of such a device. A waveform generator capable of real-time pre-distortion of a radar waveform to a given time-base distortion function is needed. To pre-distort the transmitted signal, both the baseband radar waveform and the RF carrier must be modified. In the GSSR, this occurs at the up-conversion mixing stage to an intermediate frequency (IF). A programmable oscillator (PO) is used to generate the IF along with a time-varying phase component that matches the time-base distortion of the RF carrier. This serves as the IF input to the waveform generator where it is mixed with a baseband radar waveform whose time-base has been distorted to match the given time-base distortion function producing the modulated IF output. An error control feedback loop is used to precisely control the time-base distortion of the baseband waveform, allowing its real-time generation. The waveform generator produces IF modulated radar waveforms whose time-base has been pre-distorted to match a given arbitrary function. The following waveforms are supported: continuous wave (CW), frequency hopped (FH), binary phase code (BPC), and linear frequency modulation (LFM). The waveform generator takes as input an IF with a time varying phase component that matches the time-base distortion of the carrier. The waveform generator supports interconnection with deep-space network (DSN) timing and frequency standards, and is controlled through a 1 Gb/s Ethernet UDP/IP interface. This real-time generation of a timebase distorted radar waveform for continuous transmission in a planetary radar is a unique capability.

Quirk, Kevin J.↗

High frequency photodiodes.

P-n junction type photodiodes for rapidly modulated light detection discussing design, performance, frequency response and sensitivity

FREQUENCY RESPONSE↗

Flexible, reconfigurable, power efficient transmitter and method

A flexible, reconfigurable, power efficient transmitter device and method is provided. In one embodiment, the method includes receiving outbound data and determining a mode of operation. When operating in a first mode the method may include modulation mapping the outbound data according a modulation scheme to provide first modulation mapped digital data, converting the first modulation mapped digital data to an analog signal that comprises an intermediate frequency (IF) analog signal, upconverting the IF analog signal to produce a first modulated radio frequency (RF) signal based on a local oscillator signal, amplifying the first RF modulated signal to produce a first RF output signal, and outputting the first RF output signal via an isolator. In a second mode of operation method may include modulation mapping the outbound data according a modulation scheme to provide second modulation mapped digital data, converting the second modulation mapped digital data to a first digital baseband signal, conditioning the first digital baseband signal to provide a first analog baseband signal, modulating one or more carriers with the first analog baseband signal to produce a second modulated RF signal based on a local oscillator signal, amplifying the second RF modulated signal to produce a second RF output signal, and outputting the second RF output signal via the isolator. The digital baseband signal may comprise an in-phase (I) digital baseband signal and a quadrature (Q) baseband signal.

Bishop, James W.↗

Simultaneous amplification of terahertz difference frequencies by an injection-seeded semiconductor laser amplifier at 850 nm

Two-frequency operation of an 850 nm semiconductor optical amplifier was achieved by simultaneously injection seeding it with two diode lasers. The two frequencies could be independently amplified without strong interference when they were separated by more than 10 GHz, and the spectral purity was preserved by the amplification process. At frequency differences below 10 GHz, unbalanced two-frequency output was observed, which can be explained by a two-mode interaction driven by the refractive index modulation at the beat frequency. The laser system is suitable for the difference-frequency generation of coherent terahertz radiation in ultra-fast photoconductors or nonlinear optical media.

NASA Discipline Exobiology↗

Diode Laser Velocity Measurements by Modulated Filtered Rayleigh Scattering

The ability of solid-state lasers to be tuned in operating frequency at MHz rates by input current modulation, while maintaining a relatively narrow line-width, has made them useful for spectroscopic measurements. Their other advantages include low cost, reliability, durability, compact size, and modest power requirements, making them a good choice for a laser source in micro-gravity experiments in drop-towers and in flight. For their size, they are also very bright. In a filtered Rayleigh scattering (FRS) experiment, a diode laser can be used to scan across an atomic or molecular absorption line, generating large changes in transmission at the resonances for very small changes in frequency. The hyperfine structure components of atomic lines of alkali metal vapors are closely spaced and very strong, which makes such atomic filters excellent candidates for sensitive Doppler shift detection and therefore for high-resolution velocimetry. In the work we describe here we use a Rubidium vapor filter, and work with the strong D(sub 2) transitions at 780 nm that are conveniently accessed by near infrared diode lasers. The low power output of infrared laser diodes is their primary drawback relative to other laser systems commonly used for velocimetry. However, the capability to modulate the laser frequency rapidly and continuously helps mitigate this. Using modulation spectroscopy and a heterodyne detection scheme with a lock-in amplifier, one can extract sub-microvolt signals occurring at a specific frequency from a background that is orders of magnitude stronger. The diode laser modulation is simply achieved by adding a small current modulation to the laser bias current. It may also be swept repetitively in wavelength using an additional lower frequency current ramp.

Mach, J. J.↗

Summer Synoptic-Scale Waves over Tropical West Africa Observed by TRMM

A 5-year daily rainfall dataset (3B42) from TRMM (Tropical Rainfall Measuring Mission) is used to investigate the activity and properties of westward-propagating synoptic-scale waves over tropical West Africa. Evident wave signals appearing in wavenumber-frequency space show their modulations on the surface rainfall pattern during the boreal summer. Interannual variability exists in both their intensity and spectral properties, i. e., dominant frequency and wavenumber ranges. These variabilities can be partly ascribed to year-to-year variations of their embedded large-scale environment, especially the status of mid-tropospheric African easterly jet (AEJ). Generally, a stronger (weaker) AEJ indicates more (less) instability energy yielding a stronger (weaker) wave activity season. Seasonal mean rainfall has shown an impact on these waves in some years. However, the impact is not as clear and consistent as AEJ, implying the complexity of their relationship with large-scale environment. To fully understand interannual variability of synoptic-scale waves over tropical West Africa, including the variability in their preferred frequencies and wavenumbers, it is therefore necessary to examine possible intra-seasonal variations existing in both wave activity and large-scale fields, in addition to their structure, propagation, and associated convection.

Starr, David O.↗

A 100-kHz frequency divider, distribution amplifier

A frequency divider, distribution amplifier module having low phase noise and low phase drift with temperature and high isolation between outputs was developed for use in the hydrogen maser frequency standard, where it divides 1 MHz from the previous frequency divider down to 100 kHz and provides four transistor-transistor logic (TTL) outputs.

Lutes, G.↗

Multiple rate digital command detection system with range clean-up capability

A multi-rate digital command system is disclosed which uses the composite signal of a mu-type ranging system as a subcarrier to transmit range codes and data from a station to a receiver where the range codes are sequentially phase modulated on a subcarrier of frequency by one of its own subharmonics and data is phase modulated on a selected ranging component. A range cleanup loop in a spacecraft locks the phase of a locally generated reference component to a received ranging component and retransmits the component to a ground station. When the inverse phase of a ranging component is received and detected, the cleanup loop is modified to demodulate phase modulated command symbols while continuing tracking the same ranging component. The command symbol rate is coherently related to the ranging signal component bit rate.

Lesh, J. R.↗

Space-to-Space Communications System

The Space-to-Space Communications System (SSCS) is an Ultra High Frequency (UHF) Time-Division-Multiple Access (TDMA) system that is designed, developed, and deployed by the NASA Johnson Space Center (JSC) to provide voice, commands, telemetry and data services in close proximity among three space elements: International Space Station (ISS), Space Shuttle Orbiter, and Extravehicular Mobility Units (EMU). The SSCS consists of a family of three radios which are, Space-to-Space Station Radio (SSSR), Space-to-Space Orbiter Radio (SSOR), and Space-to-Space Extravehicular Mobility Radio (SSER). The SSCS can support up to five such radios at a time. Each user has its own time slot within which to transmit voice and data. Continuous Phase Frequency Shift Keying (CPFSK) carrier modulation with a burst data rate of 695 kbps and a frequency deviation of 486.5 kHz is employed by the system. Reed-Solomon (R-S) coding is also adopted to ensure data quality. In this paper, the SSCS system requirements, operational scenario, detailed system architecture and parameters, link acquisition strategy, and link performance analysis will be presented and discussed

Kwei tU↗

An electric noise component with density 1/f identified on ISEE 3

The properties of the 1/f noise detected at the terminals of ISEE 3 antennas are described and related to the solar wind parameters. The 1/f noise was observed with the radio receivers of the three-dimensional radio mapping experiment using the S and Z dipole antennas. The noise spectra contained a negative spectral index component at frequencies lower than 0.7 of the plasma frequency, and 5-10 times the predicted thermal noise for the Z antenna. S-antenna measurements of the 1/f component revealed it to be deeply spin modulated with a minimum electric field in the direction of the solar wind. Modulation increases with increasing frequency, becomes negligible when the 1/f intensity is negligible with respect to the thermal noise, and increases with solar wind velocity. The possibilities that the noise is due either to waves or currents are discussed.

Hoang, S.↗