Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flow loop”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Pulse thermal loop

A pulse thermal loop heat transfer system includes a means to use pressure rises in a pair of evaporators to circulate a heat transfer fluid. The system includes one or more valves that iteratively, alternately couple the outlets the evaporators to the condenser. While flow proceeds from one of the evaporators to the condenser, heating creates a pressure rise in the other evaporator, which has its outlet blocked to prevent fluid from exiting the other evaporator. When the flow path is reconfigured to allow flow from the other evaporator to the condenser, the pressure in the other evaporator is used to circulate a pulse of fluid through the system. The reconfiguring of the flow path, by actuating or otherwise changing the configuration of the one or more valves, may be triggered when a predetermined pressure difference between the evaporators is reached.

Weislogel, Mark M.↗

Active Control of High Frequency Combustion Instability in Aircraft Gas-Turbine Engines

Active control of high-frequency (greater than 500 Hz) combustion instability has been demonstrated in the NASA single-nozzle combustor rig at United Technologies Research Center. The combustor rig emulates an actual engine instability and has many of the complexities of a real engine combustor (i.e. actual fuel nozzle and swirler, dilution cooling, etc.) In order to demonstrate control, a high-frequency fuel valve capable of modulating the fuel flow at up to 1kHz was developed. Characterization of the fuel delivery system was accomplished in a custom dynamic flow rig developed for that purpose. Two instability control methods, one model-based and one based on adaptive phase-shifting, were developed and evaluated against reduced order models and a Sectored-1-dimensional model of the combustor rig. Open-loop fuel modulation testing in the rig demonstrated sufficient fuel modulation authority to proceed with closed-loop testing. During closed-loop testing, both control methods were able to identify the instability from the background noise and were shown to reduce the pressure oscillations at the instability frequency by 30%. This is the first known successful demonstration of high-frequency combustion instability suppression in a realistic aero-engine environment. Future plans are to carry these technologies forward to demonstration on an advanced low-emission combustor.

Corrigan, Bob↗

Pump, and earth-testable spacecraft capillary heat transport loop using augmentation pump and check valves

A spacecraft includes heat-generating payload equipment, and a heat transport system with a cold plate thermally coupled to the equipment and a capillary-wick evaporator, for evaporating coolant liquid to cool the equipment. The coolant vapor is coupled to a condenser and in a loop back to the evaporator. A heated coolant reservoir is coupled to the loop for pressure control. If the wick is not wetted, heat transfer will not begin or continue. A pair of check valves are coupled in the loop, and the heater is cycled for augmentation pumping of coolant to and from the reservoir. This augmentation pumping, in conjunction with the check valves, wets the wick. The wick liquid storage capacity allows the augmentation pump to provide continuous pulsed liquid flow to assure continuous vapor transport and a continuously operating heat transport system. The check valves are of the ball type to assure maximum reliability. However, any type of check valve can be used, including designs which are preloaded in the closed position. The check valve may use any ball or poppet material which resists corrosion. For optimum performance during testing on Earth, the ball or poppet would have neutral buoyancy or be configured in a closed position when the heat transport system is not operating. The ball may be porous to allow passage of coolant vapor.

Baker, David↗

Redesigned Human Metabolic Simulator

A design has been formulated for a proposed improved version of an apparatus that simulates atmospheric effects of human respiration by introducing controlled amounts of carbon dioxide, water vapor, and heat into the air. Denoted a human metabolic simulator (HMS), the apparatus is used for testing life-support equipment when human test subjects are not available. The prior version of the HMS, to be replaced, was designed to simulate the respiratory effects of as many as four persons. It exploits the catalytic combustion of methyl acetate, for which the respiratory quotient (the molar ratio of carbon dioxide produced to oxygen consumed) is very close to the human respiratory quotient of about 0.86. The design of the improved HMS provides for simulation of the respiratory effects of as many as eight persons at various levels of activity. The design would also increase safety by eliminating the use of combustion. The improved HMS (see figure) would include a computer that would exert overall control. The computer would calculate the required amounts of oxygen removal, carbon dioxide addition, water addition, and heat addition by use of empirical equations for metabolic profiles of respiration and heat. A blower would circulate air between the HMS and a chamber containing a life-support system to be tested. With the help of feedback from a mass flowmeter, the blower speed would be adjusted to regulate the rate of flow according to the number of persons to be simulated and to a temperature-regulation requirement (the air temperature would indirectly depend on the rate of flow, among other parameters). Oxygen would be removed from the circulating air by means of a commercially available molecular sieve configured as an oxygen concentrator. Oxygen, argon, and trace amounts of nitrogen would pass through a bed in the molecular sieve while carbon dioxide, the majority of nitrogen, and other trace gases would be trapped by the bed and subsequently returned to the chamber. If, as recommended, the oxygen concentrator were of a rotating twelve-bed design, then variations in the product stream could be made very small. Carbon dioxide would be added directly to the circulating air by simple injection from a supply tank. The rate of injection would be maintained at the required rate by use of a mass flowmeter/controller. In the same way, nitrogen would be added to make up for the small amount of nitrogen lost through the oxygen concentrator. Water vapor would be added to the circulating air by heating the corresponding required flow of water to steam in a heat exchanger. More heat, required to complete the simulation of the thermal effect of respiration, would be added through another heat exchanger. Heat would be supplied to both heat exchangers via a hot-oil loop.

Duffield, Bruce↗

Design and Modeling of a Variable Heat Rejection Radiator

Variable Heat Rejection Radiator technology needed for future NASA human rated & robotic missions Primary objective is to enable a single loop architecture for human-rated missions (1) Radiators are typically sized for maximum heat load in the warmest continuous environment resulting in a large panel area (2) Large radiator area results in fluid being susceptible to freezing at low load in cold environment and typically results in a two-loop system (3) Dual loop architecture is approximately 18% heavier than single loop architecture (based on Orion thermal control system mass) (4) Single loop architecture requires adaptability to varying environments and heat loads

fluid flow↗

Requirements and Design Reference Mission for the WFIRST-AFTA Coronagraph Instrument

The WFIRST-AFTA coronagraph instrument take s advantage of AFTA s 2.4 -meter aperture to provide novel exoplanet imaging science at approximately the same instrument cost as an Explorer mission. The AFTA coronagraph also matures direct imaging technologies to high TRL for an Exo-Earth Imager in the next decade. The coronagraph Design Reference Mission (DRM) optical design is based on the highly successful High Contrast Imaging Testbed (HCIT), with modifications to accommodate the AFTA telescope design, service-ability, volume constraints, and the addition of an Integral Field Spectrograph (IFS). In order to optimally satisfy the three science objectives of planet imaging, planet spectral characterization and dust debris imaging, the coronagraph is designed to operate in two different modes : Hybrid Lyot Coronagraph or Shaped Pupil Coronagraph. Active mechanisms change pupil masks, focal plane masks, yot masks, and bandpass filters to shift between modes. A single optical beam train can thus operate alternatively as two different coronagraph architecture s. Structural Thermal Optical Performance (STOP) analysis predict s the instrument contrast with the Low Order Wave Front Control loop closed. The STOP analysis was also used to verify that the optical/structural/thermal design provides the extreme stability required for planet characterization in the presence of thermal disturbances expected in a typical observing scenario. This paper describes the instrument design and the flow down from science requirements to high level engineering requirements.

contrast↗

A Correction Method for Unsteady Transonic Aerodynamics

This paper presents a new method for transonic pitching airfoils based on a RANS CFD study and the Theodorsen model of an oscillating pitching flat plate. This study quantifies the deviation of the lift coefficient predictions using CFD from that obtained using the Theodorsen model, which is based on the incompressible potential flow assumption. The present method corrects this theoretical model by modulating the Theodorsen functions by coefficient functions that depend on the reduced frequency and the Mach number. It is demonstrated that the modified theoretical model predicts lift coefficient in good agreement with the CFD results in the Mach number range from incompressible (M =0.2) to transonic (M =0.755) flow for a range of reduced frequencies typical of transonic flutter. The simulations are first validated by comparing pitching NACA0012 airfoil results with experimental results at transonic flight conditions, which establishes the requirements for a grid converged unsteady transonic solution. The hysteresis loop, Cl versus α, attains a grid independent solution that compares well with experiment. The present correction method will guide the development of a new state space model for the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system and eventually a new transfer function that will be incorporated in a new aeroelastic framework leading to an appropriate transonic flutter model for use in the future aircraft systems in development under the NASA Advanced Air Transportation Technologies (AATT) project.

Kaul, Upender K.↗

Numerical Simulation of AFP Nip Point Temperature Prediction for Complex Geometries

Material placement at the ideal nip point temperature over complex surfaces with uniformity across the width of the compaction rollers results in optimized part properties for Automated Fiber Placement (AFP) processes. However, current AFP systems utilize heat control models and methodologies, based on multiple process parameters such as feed-rate and orientation, that are mostly open-loop. Here, infrared (IR) heater input is calibrated as a function of process parameters during machine qualification. This work presents a numerical simulation to predict arrayed-infrared (AIR) emitter radiation onto a substrate that includes view factor implementation, IR radiative heat flow calculation, energy rate balance, and a transient heat transfer model. The purpose of this numerical model is to predict nip point temperature on complex surfaces, serving as a baseline for a new arrayed-infrared (AIR) thermoset heater to improve AFP process control. It is anticipated that this simulation will accurately control the temperature for high-speed AFP layup of complex geometries. An anticipated result of an AIR heater system is that material calibration and testing will be reduced as temperature is instantaneously monitored and controlled. Therefore, temperature across the roller width will be uniform during placement of complex parts, independent of their geometry.

Xia, Kaishu↗

A Simplified Model of VIPER Thermal Management System. Part I: Loop Heat Pipe

NASA’s Volatiles Investigating Polar Exploration Rover (VIPER) uses a combination of loop heat pipes (LHPs) and heaters as the primary hardware to modulate the temperature of the electronic boxes and payloads instruments. LHPs have been designed and instrumented to be capable of passive and active shutdown. The goal of the passive shutdown, using a thermal control valve (TCV) to limit the flow of the working fluid, is to preserve thermal energy and avoid unnecessary heat leaks during lunar night. The goal of the active shutdown on the other hand, is to forcefully increase the vehicle internal temperature to bakeout the payload instruments. Several numerical modeling tools are available to analyze LHP performance under the complex set of operational requirements and environments levied on the VIPER Thermal Management System (TMS). Yet, while those numerical modeling tools are capable of detailed performance analysis, they tend to take large computational resources and long computational time. In this paper, a model of a single LHP developed based on control volume approach is presented. By using the control volume approach, the complex geometry of the LHP, and the components attached to it, are reduced to thermal lump capacitances, thus reducing the computation effort. This paper also describes the effort to correlate the proposed LHP model using thermal vacuum (TVAC) test data.

Loop Heat Pipe↗

A Simplified Model of VIPER Thermal Management System. Part I: Loop Heat Pipe

NASA’s Volatiles Investigating Polar Exploration Rover (VIPER) uses a combination of loop heat pipes (LHPs) and heaters as the primary hardware to modulate the temperature of the electronic boxes and payloads instruments. LHPs have been designed and instrumented to be capable of passive and active shutdown. The goal of the passive shutdown, using a thermal control valve (TCV) to limit the flow of the working fluid, is to preserve thermal energy and avoid unnecessary heat leaks during lunar night. The goal of the active shutdown on the other hand, is to forcefully increase the vehicle internal temperature to bakeout the payload instruments. Several numerical modeling tools are available to analyze LHP performance under the complex set of operational requirements and environments levied on the VIPER Thermal Management System (TMS). Yet, while those numerical modeling tools are capable of detailed performance analysis, they tend to take large computational resources and long computational time. In this paper, a model of a single LHP developed based on control volume approach is presented. By using the control volume approach, the complex geometry of the LHP, and the components attached to it, are reduced to thermal lump capacitances, thus reducing the computation effort. This paper also describes the effort to correlate the proposed LHP model using thermal vacuum (TVAC) test data.

Loop Heat Pipe↗

Development of a multicomponent force and moment balance for water tunnel applications, volume 2

The principal objective of this research effort was to develop a multicomponent strain gauge balance to measure forces and moments on models tested in flow visualization water tunnels. Static experiments (which are discussed in Volume 1 of this report) were conducted, and the results showed good agreement with wind tunnel data on similar configurations. Dynamic experiments, which are the main topic of this Volume, were also performed using the balance. Delta wing models and two F/A-18 models were utilized in a variety of dynamic tests. This investigation showed that, as expected, the values of the inertial tares are very small due to the low rotating rates required in a low-speed water tunnel and can, therefore, be ignored. Oscillations in pitch, yaw and roll showed hysteresis loops that compared favorably to data from dynamic wind tunnel experiments. Pitch-up and hold maneuvers revealed the long persistence, or time-lags, of some of the force components in response to the motion. Rotary-balance experiments were also successfully performed. The good results obtained in these dynamic experiments bring a whole new dimension to water tunnel testing and emphasize the importance of having the capability to perform simultaneous flow visualization and force/moment measurements during dynamic situations.

Suarez, Carlos J.↗

The structure of extruded NiAl

The deformation structure of Ni-rich NiAl extruded at 550 C has been characterized by transmission electron microscopy and by optical microscopy. Dislocations having a(100) Burgers vectors were found as complex networks, tangles, and prismatic loops. a(110) dislocations, which were rare, were concluded to arise from reactions of a(100) dislocations. Evidence of recovery and recrystallization was obtained. Extrusion was deemed to have been possible by the operation of (hko)(001) slip systems (often in plane strain flow) plus diffusion-assisted processes.

Baker, I.↗

Enthalpy By Energy Balance for Aerodynamic Heating Facility at NASA Ames Research Center Arc Jet Complex

The NASA Ames Research Center (ARC) Arc Jet Facilities' Aerodynamic Heating Facility (AHF) has been instrumented for the Enthalpy By Energy Balance (EB2) method. Diagnostic EB2 data is routinely taken for all AHF runs. This paper provides an overview of the EB2 method implemented in the AHF. The chief advantage of the AHF implementation over earlier versions is the non-intrusiveness of the instruments used. For example, to measure the change in cooling water temperature, thin film 1000 ohm Resistance Temperature Detectors (RTDs) are used with an Anderson Current Loop (ACL) as the signal conditioner. The ACL with 1000 ohm RTDs allows for very sensitive measurement of the increase in temperature (Delta T) of the cooling water to the arc heater, which is a critical element of the EB2 method. Cooling water flow rates are measured with non-intrusive ultrasonic flow meters.

Hightower, T. Mark↗

A Multi-Disciplinary Analysis Framework for the Design of Small Launch Vehicles

Between the years of 1995 and 2014 the number of small satellites (1-500 kg) went up from 20 to 180. [1] Out of the 180 launched in 2014 66% were Nano satellites (1-10 kg). [1] With this trend of smaller satellites, one would expect a rise in number of small launch vehicles (SLVs are defined by capability to carry 1-100 kg to orbit), but this has not happened: [3] only 8% of all small satellites are launched on SLVs and the others become secondary payloads on regular launch vehicles. [1] This results in small satellites being placed into either suboptimal orbits or waiting for launch schedules to align with bigger launches, resulting in long waiting times. Dedicated SLVs could improve the responsiveness of small satellite launches, but SLV design is complicated by the large architecture space needed to be explored in order to find efficient and affordable designs. The SLV architecture trade space contains many discrete options, e.g. solid vs. liquid fuels, air launch vs. ground launch, number of stages, etc. [2][3] Performing detailed analysis for all the options at once would be prohibitive. Thus, a sizing environment/framework that is capable of providing necessary information for conceptual-level trade studies and can rapidly explore the vast SLV architecture space is necessary. The framework, illustrated in Figure 1, consists of four disciplines central to the sizing and synthesis of launch vehicles: propulsion, aerodynamics, structures, and trajectory. For the aerodynamics and trajectory disciplines, Missile DATCOM and POST2 are used, respectively. The propulsion and structures disciplines are represented in the framework with tools developed at ASDL Georgia Tech. For propulsion, the Solid Motor Analysis Code (SMAC) is a physics-based conceptual design tool for solid rocket motors. SMAC is capable of geometric burn simulation, ballistic analysis, and prediction of thrust performance. [4] For structures, Launch Vehicle Structural Analysis (LVSA) tool is a physics-based tool that focuses on structural dynamic analysis with sizing capability. These tools are integrated into the framework illustrated in Figure 1 with the corresponding connections described in Table 1. The process flow is as follows: first, SMAC sizes insulation and calculates maximum operating pressures for each vehicle stage. The MEOP and insulation thickness values from SMAC are fed to LVSA which then utilizes this information to size the motor casing. This creates a feedback loop between LVSA and SMAC that converges on the radius available for fuel, casing, and insulation thickness. Once the stage sizing is converged on SMAC creates an engine deck that is passed to POST2. Next, the data from SMAC and LVSA goes into Missile DATCOM which generates an aerodynamics database for POST2. Finally, POST2 performs a targeting optimization while maximizing the payload mass to orbit. Within the framework, POST2 is automated in order to be robust to a wide variety of possible designs by performing a Monte Carlo simulation over the initialization vector of the POST2 optimization variables. To demonstrate the capability of this framework, a sample problem of exploring the design space of an SLV capable of placing satellites into a low Earth orbit (inclination=47 deg, 196.5 by 211.3 nm) is used. This sample problem is a ground-launched SLV consisting of four in-line SRM stages. The multidisciplinary design analysis (MDA) environment is utilized to explore a design space consisting of 22 continuous and 12 discrete variables, shown by Table 1 by blocks 1,2,3. Running a full factorial design of experiments (DOE) would have been prohibitively expensive even with this reduced design space, thus a space filling design with 3,502 and then additional expansion of 2,602 cases was used. The first DOE consisted of 3,502 cases, and all of the variables were varied. These input variables are listed in blocks 1, 2, and 3 in Table 1. Most of the variables are propulsion related with stage lengths determining the delta-V split of the SLV. The expansion consisted of 2,602 cases, and the continuous variables were set to be equal to the most promising designs from the sizing of first DOE. For each set of continuous variables, the discrete variables (grain type, star points, and propellant) were to varied. The results of the DOE can be seen in Figure 2; each of the points in this plot represents a closed launch vehicle that reaches the targeted orbit. For each of the cases, there is information on flown trajectory, structural, and propulsion properties of the SLV. For example, Figure 3 shows changes in altitude and velocity with time for a particular case. The right side of Figure 3 clearly shows the coasting (slow decrease) and burning phases (sharp increase) of the SLV mission. LV mass is positively correlated with the optimized payload mass to orbit because heavier LVs carry more fuel and thus have more stored chemical energy. Furthermore, for any given payload mass to orbit, the most efficient design would result in the smallest LV. The results as visualized in Figure 2 shows this tradeoff, and the Pareto frontier of the efficient designs can be seen along the dotted line. Figure 2 can be divided into regions with the lowest mass vehicles corresponding to the minimum bound on radius, and the highest mass vehicles corresponding to the maximum bound on radius. Within a mass region, the discrete variables, such as propellant type and propellant grain arrangement, have the most effect on payload mass. This paper presents an MDA framework that can perform an automated physics-based sizing of SLV designs and a corresponding methodology to utilize the MDA to explore the design space of SLVs. The proposed methodology was applied to a perform a design space exploration for a four stage SLV. The outputs show the expected pareto frontier forming and provide detailed information about the SLV performance and staging. Using the produced data, it will be possible to select a set of pareto optimal designs that can then be further explored in subsequent design cycles. This demonstration shows that automated design space exploration should be used in the early phase design of future SLV concepts.

Nikita S Birbasov↗

Advanced Hybrid Spacesuit Concept Featuring Integrated Open Loop and Closed Loop Ventilation Systems

A document discusses the design and prototype of an advanced spacesuit concept that integrates the capability to function seamlessly with multiple ventilation system approaches. Traditionally, spacesuits are designed to operate both dependently and independently of a host vehicle environment control and life support system (ECLSS). Spacesuits that operate independent of vehicle-provided ECLSS services must do so with equipment selfcontained within or on the spacesuit. Suits that are dependent on vehicle-provided consumables must remain physically connected to and integrated with the vehicle to operate properly. This innovation is the design and prototype of a hybrid spacesuit approach that configures the spacesuit to seamlessly interface and integrate with either type of vehicular systems, while still maintaining the ability to function completely independent of the vehicle. An existing Advanced Crew Escape Suit (ACES) was utilized as the platform from which to develop the innovation. The ACES was retrofitted with selected components and one-off items to achieve the objective. The ventilation system concept was developed and prototyped/retrofitted to an existing ACES. Components were selected to provide suit connectors, hoses/umbilicals, internal breathing system ducting/ conduits, etc. The concept utilizes a lowpressure- drop, high-flow ventilation system that serves as a conduit from the vehicle supply into the suit, up through a neck seal, into the breathing helmet cavity, back down through the neck seal, out of the suit, and returned to the vehicle. The concept also utilizes a modified demand-based breathing system configured to function seamlessly with the low-pressure-drop closed-loop ventilation system.

Daniel, Brian A.↗

Dynamic stall of an oscillating wing. Part 1: Evaluation of turbulence models

Unsteady flowfields of a two-dimensional oscillating wing are calculated using an implicit, finite-difference, Navier-Stokes numerical scheme using five widely used turbulence models. The objective of this study is to identify an appropriate turbulence model for accurate simulation of three-dimensional dynamic stall. Three unsteady flow conditions corresponding to attached flow, light-stall, and deep-stall of an oscillating wing experiment were chosen as test cases for computations. Results of unsteady airload hysteresis curves, harmonics of unsteady pressures, and instantaneous flow pictures are presented. Comparison of unsteady airloads with experiment show that all models are deficient in some sense and not a single model predicts all airloads consistently and in agreement with experiment for all flow conditions. For the attached flow condition, the Renormalization Group Theory (RNG), the Johnoson-King (J-K), and the Spalart-Allmaras (S-A) models have better performance. The Baldwin-Lomax (B-L) and the Baldwin-Barth (B-B) models fair poorly. At the light-stall condition, the results for the RNG, the J-K, and S-A models are in agreement with experiment for the upstroke but they all over predict the separation shown by the experiment and therefore have bigger hysteresis loops than experimental results. The B-B model results are also in good agreement for upstroke but have poor lift hysteresis for downstroke. It has superior drag and pitching-moment predictions. For deep-stall conditions, the airloads for the RNG, the B -B, and the S-A models have fair agreement with experiment, but the B-B model performed better at the extreme deep-stall condition. Overall, the RNG model provides significant improvement over the B-L model in all flow regimes with no additional computational cost. The Baldwin-Barth model is the most expensive of the models considered here, costing about 2.5 times that of the Baldwin-Lomax model. Finally, a brief discussion of the effects of grid density, time-step size, and numerical dissipation on the unsteady solutions are also presented.

Srinivasan, G. R.↗

Ultraviolet observations of the Cygnus Loop

The analysis of IUE observations of a filament on the western edge of the Cygnus Loop yields a shock velocity of about 130 km/sec, significantly higher than the velocity estimated from the optical spectrum. This velocity together with the high forbidden O III/H-beta ratio reported by Miller (1974) indicates that much of the hydrogen recombination region predicted by steady flow shock models is absent. This situation may occur because this part of the supernova remnant is in the shell-formation phase that accompanies the transition from the adiabatic to the snowplow phase or because the observed filament is a recently shocked cloud.

Raymond, J. C.↗

Magnetohydrodynamic modeling of the solar corona

The ideal and resistive magnetohydrodynamic (MHD) model is used to examine the dynamics and structure of the solar corona. When the coronal magnetic field is deformed by photospheric flow it can evolve to states that become unstable to ideal MHD modes. The nonlinear evolution of these instabilities can lead to the generation of current sheets, field line reconnection, and energy release. The disruption of an arcade field and the kinking of coronal loops is described. The braiding of the large-scale coronal field by convective photospheric motions develops fine-scale structure in the magnetic field and leads to the development of intense current filaments. The resistive dissipation of these currents can provide an efficient coronal heating mechanism.

Mikic, Zoran↗