Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Edge Computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Some Effects of Bluntness on Boundary-Layer Transition and Heat Transfer at Supersonic Speeds

Large downstream movements of transition observed when the leading edge of a hollow cylinder or a flat plate is slightly blunted are explained in terms of the reduction in Reynolds number at the outer edge of the boundary layer due to the detached shock wave. The magnitude of this reduction is computed for cones and wedges for Mach numbers to 20. Concurrent changes in outer-edge Mach number and temperature occur in the direction that would increase the stability of the laminar boundary layer. The hypothesis is made that transition Reynolds number is substantially unchanged when a sharp leading edge or tip is blunted. This hypothesis leads to the conclusion that the downstream movement of transition is inversely proportional to the ratio of surface Reynolds number with blunted tip or leading edge to surface Reynolds number with sharp tip or leading edge. The conclusion is in good agreement with the hollow-cylinder result at Mach 3.1.

Moeckel, W E↗
DOE OSTI2020

Electronic Bottleneck Suppression in Next‐Generation Networks with Integrated Photonic Digital‐to‐Analog Converters

Digital‐to‐analog converters (DAC) are indispensable functional units in signal processing instrumentation and wide‐band telecommunication links for both civil and military applications. As photonic systems are capable of high data throughput and low latency, an increasingly found system limitation stems from the required domain crossing such as digital to analog and electronic to optical. A photonic DAC implementation, in contrast, enables a seamless signal conversion with respect to both energy efficiency and short signal delay, often requiring bulky discrete optical components and electric–optic transformation, hence introducing inefficiencies. Herein, a novel coherent parallel photonic DAC concept along with a 4‐bit experimental prototype capable of performing this DAC without optic–electric–optic domain crossing is introduced. This new paradigm guarantees a linear intensity weighting among bits when operating at high sampling rates (50 GHz), featuring an exceptional sampling efficiency (> 100 GS ) and small footprint (≈1 mm 2 ) in an 8‐bit implementation. Importantly, this photonic DAC enables seamless interfaces of next‐generation data processing hardware with high relevance in data centers, task‐specific compute accelerators such as neuromorphic engines, and network edge processing applications.

Meng, Jiawei↗
DOE OSTI2023

Mechanics of Dynamic and Deformable DNA Nanostructures

In DNA nanotechnology, DNA molecules are designed, engineered, and assembled into arbitrary-shaped architectures with predesigned functions. Static DNA assemblies often have delicate designs with structural rigidity to overcome thermal fluctuations. Dynamic structures reconfigure in response to external cues, which have been explored to create functional nanodevices for environmental sensing and other applications. However, the precise control of reconfiguration dynamics has been a challenge due partly to flexible single-stranded DNA connections between moving parts. Deformable structures are special dynamic constructs with deformation on double-stranded parts and single-stranded hinges during transformation. These structures often have better control in programmed deformation. However, related deformability and mechanics including transformation mechanisms are not well understood or documented. In this review, we summarize the development of dynamic and deformable DNA nanostructures from a mechanical perspective. We present deformation mechanisms such as single-stranded DNA hinges with lock-and-release pairs, jack edges, helicity modulation, and external loading. Theoretical and computational models are discussed for understanding their associated deformations and mechanics. We elucidate the pros and cons of each model and recommend design processes based on the models. The design guidelines should be useful for those who have limited knowledge in mechanics as well as expert DNA designers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Simulated field-modulated x-ray absorption in titania

Here, we present a method to compute the x-ray absorption near-edge structure (XANES) spectra of solid-state transition metal oxides using real-time time-dependent density functional theory, including spin–orbit coupling effects. This was performed on bulk-mimicking anatase titania (TiO 2 ) clusters, which allows for the use of hybrid functionals and atom-centered all electron basis sets. Furthermore, this method was employed to calculate the shifts in the XANES spectra of the Ti L-edge in the presence of applied electric fields to understand how external fields can modify the electronic structure, and how this can be probed using x-ray absorption spectroscopy. Specifically, the onset of t 2g peaks in the Ti L-edge was observed to red shift and the e g peaks were observed to blue shift with increasing fields, attributed to changes in the hybridization of the conduction band (3d) orbitals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

SWARM: Reimagining scientific workflow management systems in a distributed world

Modern scientific workflows process massive amounts of data from diverse instruments and sensors, leveraging geographically distributed, heterogeneous compute and storage resources—from leadership-class systems to edge devices—connected by high-performance networks. The diversity of resources introduces challenges in harnessing their full potential, with resilience issues arising across applications, system software, networks, storage, and hardware. Today, workflow management systems (WMS) coordinate the execution of computation and data management tasks across target resources. However, WMS’s centralized nature makes them vulnerable to faults and scalability issues that may result in failures of entire computational campaigns. In conclusion, this paper introduces a novel agentic framework for workflow management, fully distributing and decentralizing the WMS functions and modeling them as swarm intelligence agents infused with advanced artificial intelligence solutions and traditional distributed computing algorithms that can make coordinated decisions in the presence of failures of the underlying cyberinfrastructure.

Swarm intelligence↗
DOE OSTI2022

Real-time GIS Programming and Geocomputation

Streaming data generated continuously from sensor networks, mobile devices, social media platforms and other edge devices have posed significant challenges to existing computing platforms for achieving both high throughput and low latency data processing in addition to scalable computing. This entry introduces a real-time computing and programming platform for time-critical GIS (Geographic Information System) applications. In this platform, advanced streaming data processing software, such as Apache Kafka and Spark Streaming, are integrated to enable data analytics in real-time. This computing platform can also be extended to integrate GeoAI (Geospatial Artificial Intelligence) based machine learning models to leverage both historical and streaming data to achieve real-time prediction and intelligent geospatial analytics. Two real-time geospatial applications in terms of flood simulation and climate data visualization are introduced to demonstrate how real-time programming and computing can help tackle real-world problems with important societal impacts.

Liu, Yan↗
NASA NTRS1971

The Determination of the Geometries of Multiple-Element Airfoils Optimized for Maximum Lift Coefficient

Optimum airfoils in the sense of maximum lift coefficient are obtained by a newly developed method. The maximum lift coefficient is achieved by requiring that the turbulent skin friction be zero in the pressure rise region on the upper surface. Under this constraint, the pressure distribution is optimized. The optimum pressure distribution consists of a uniform stagnation pressure on the lower surface, a uniform minimum pressure on the upper surface immediately downstream of the front stagnation point followed by a Stratford zero skin friction pressure rise. When multiple-element airfoils are under consideration, this optimum pressure distribution appears on every element. The parameters used to specify the pressure distribution on each element are the Reynolds number and the normalized trailing edge velocity. The newly developed method of design computes the velocity distribution on a given airfoil and modifies the airfoil contour in a systematic manner until the desired velocity distribution is achieved. There are no limitations on how many elements the airfoil to be designed can have.

Chen, A. W.↗
NASA NTRS1974

Boundary and object detection in real world images

A solution to the problem of automatic location of objects in digital pictures by computer is presented. A self-scaling local edge detector which can be applied in parallel on a picture is described. Clustering algorithms and boundary following algorithms which are sequential in nature process the edge data to locate images of objects.

Yakimovsky, Y.↗
NASA NTRS1976

Difference thresholds for judgments of sink rate during the flare

Past studies have shown that touchdown rates of descent (sink rates) are higher in aircraft simulators than in aircraft under similar conditions. The objective of this paper was to use a psychophysical technique to investigate a pilot's ability to distinguish between two different sink rates close to the ground. The pilots observed a collimated computer graphics display of a typical runway with edge, zone, and centerline lights. The results showed that with a forward velocity of 120 knots, pilots could reliably distinguish between a sink rate of 0.5 m/sec (1.7 ft/sec) and 0.9 m/sec (2.9 ft/sec). The results also showed that the absolute rate of sink did not significantly affect the perception of sink rate. Time of sink and total height drop during the sink did affect the minimum detectable difference between sink rates (the differential threshold). The effects were such that a greater time of sink and greater height drop produced lower thresholds

Palmer, E.↗
NASA NTRS1978

Computer quantitation of coronary angiograms

A computer technique is being developed at the Jet Propulsion Laboratory to automate the measurement of coronary stenosis. A Vanguard 35mm film transport is optically coupled to a Spatial Data System vidicon/digitizer which in turn is controlled by a DEC PDP 11/55 computer. Programs have been developed to track the edges of the arterial shadow, to locate normal and atherosclerotic vessel sections and to measure percent stenosis. Multiple frame analysis techniques are being investigated that involve on the one hand, averaging stenosis measurements from adjacent frames, and on the other hand, averaging adjacent frame images directly and then measuring stenosis from the averaged image. For the latter case, geometric transformations are used to force registration of vessel images whose spatial orientation changes.

Ledbetter, D. C.↗
NASA NTRS1985

Lift due to thickness for low aspect ratio wings in incompressible flow

The problem under consideration is a numerical study of the effects of thickness on lift for low aspect ratio wings in steady incompressible inviscid flow at moderate angles of attack. At these angles of attack the flow separates along the leading edge giving rise to a lift substantially higher than that computed by classical attached flow potential theory. The problem is treated as a perturbation expansion in a small thickness parameter. The lifting elements of the flow are modeled using a nonlinear vortex lattice method which replaces the leading and trailing edge vortex sheets by segmented straight vortex filaments. The thickness elements of the flow are modeled with a mean plane source distribution and a modification to the wing boundary conditions. Results are obtained for wings with biconvex and NACA 0012 sections which compare well with available experimental data. The important observation that the effect of thickness is to decrease the lift is made.

Dodbele, S. S.↗
NASA NTRS1986

User's manual for semi-circular compact range reflector code

A computer code was developed to analyze a semi-circular paraboloidal reflector antenna with a rolled edge at the top and a skirt at the bottom. The code can be used to compute the total near field of the antenna or its individual components at a given distance from the center of the paraboloid. Thus, it is very effective in computing the size of the sweet spot for RCS or antenna measurement. The operation of the code is described. Various input and output statements are explained. Some results obtained using the computer code are presented to illustrate the code's capability as well as being samples of input/output sets.

Gupta, Inder J.↗
NASA NTRS1987

Computer-aided analysis for the Mechanics of Granular Materials (MGM) experiment, part 2

Computer vision based analysis for the MGM experiment is continued and expanded into new areas. Volumetric strains of granular material triaxial test specimens have been measured from digitized images. A computer-assisted procedure is used to identify the edges of the specimen, and the edges are used in a 3-D model to estimate specimen volume. The results of this technique compare favorably to conventional measurements. A simplified model of the magnification caused by diffraction of light within the water of the test apparatus was also developed. This model yields good results when the distance between the camera and the test specimen is large compared to the specimen height. An algorithm for a more accurate 3-D magnification correction is also presented. The use of composite and RGB (red-green-blue) color cameras is discussed and potentially significant benefits from using an RGB camera are presented.

Parker, Joey K.↗
NASA NTRS1991

Effect of non-equilibrium flow chemistry and surface catalysis on surface heating to AFE

The effect of nonequilibrium flow chemistry on the surface temperature distribution over the forebody heat shield on the Aeroassisted Flight Experiment (AFE) vehicle was investigated using a reacting boundary-layer code. Computations were performed by using boundary-layer-edge properties determined from global iterations between the boundary-layer code and flow field solutions from a viscous shock layer (VSL) and a full Navier-Stokes solution. Surface temperature distribution over the AFE heat shield was calculated for two flight conditions during a nominal AFE trajectory. This study indicates that the surface temperature distribution is sensitive to the nonequilibrium chemistry in the shock layer. Heating distributions over the AFE forebody calculated using nonequilibrium edge properties were similar to values calculated using the VSL program.

Stewart, David A.↗
NASA NTRS1992

Dynamic analysis of a pre-and-post ice impacted blade

The dynamic characteristics of an engine blade are evaluated under pre-and-post ice impact conditions using the NASA in-house computer code BLASIM. The ice impacts the leading edge of the blade causing severe local damage. The local structural response of the blade due to the ice impact is predicted via a transient response analysis by modeling only a local patch around the impact region. After ice impact, the global geometry of the blade is updated using deformations of the local patch and a free vibration analysis is performed. The effects of ice impact location, size and ice velocity on the blade mode shapes and natural frequencies are investigated. The results indicate that basic nature of the mode shapes remains unchanged after impact and that the maximum variation in natural frequencies occurs for the twisting mode of the blade.

Abumeri, G. H.↗
NASA NTRS1992

Dynamic analysis of a pre-and-post ice impacted blade

The dynamic characteristics of an engine blade are evaluated under pre-and-post ice impact conditions using the NASA in-house computer code BLASIM. The ice impacts the leading edge of the blade causing severe local damage. The local structural response of the blade due to the ice impact is predicted via a transient response analysis by modeling only a local patch around the impact region. After ice impact, the global geometry of the blade is updated using deformations of the local patch and a free vibration analysis is performed. The effects of ice impact location, ice size and ice velocity on the blade mode shapes and natural frequencies are investigated. The results indicate that basic nature of the mode shapes remains unchanged after impact and that the maximum variation in natural frequencies occurs for the twisting mode of the blade.

Abumeri, G. H.↗
NASA NTRS1923

Lift and drag effects of wing-tip rake

This report deals with a description and report of tests carried out at the Washington Navy Yard on models of the RAF-6, albatross and Slone airfoils to determine the effectiveness of the conventional wing-trailing edge being always longer than the leading edge. The results are compared with the values computed by standard formulae in use at the time the tests were conducted.

Zahm, A F↗
NASA NTRS1993

Computation of turbulent flows over backward and forward-facing steps using a near-wall Reynolds stress model

Separation and reattachment of turbulent shear layers is observed in many important engineering applications, yet it is poorly understood. This has motivated many studies on understanding and predicting the processes of separation and reattachment of turbulent shear layers. Both of the situations in which separation is induced by adverse pressure gradient, or by discontinuities of geometry, have attracted attention of turbulence model developers. Formulation of turbulence closure models to describe the essential features of separated turbulent flows accurately is still a formidable task. Computations of separated flows associated with sharp-edged bluff bodies are described. For the past two decades, the backward-facing step flow, the simplest separated flow, has been a popular test case for turbulence models. Detailed studies on the performance of many turbulence models, including two equation turbulence models and Reynolds stress models, for flows over steps can be found in the papers by Thangam & Speziale and Lasher & Taulbee). These studies indicate that almost all the existing turbulence models fail to accurately predict many important features of back step flow such as reattachment length, recovery rate of the redeveloping boundary layers downstream of the reattachment point, streamlines near the reattachment point, and the skin friction coefficient. The main objectives are to calculate flows over backward and forward-facing steps using the NRSM and to make use of the newest DNS data for detailed comparison. This will give insights for possible improvements of the turbulence model.

Ko, Sung HO↗