Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Downlink”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

LITE data processing

The Lidar In-space Technology Experiment (LITE) was a payload onboard the Space Shuttle Discovery as part of the September 1994 STS-64 mission. LITE successfully made both atmospheric and surface measurements at the 355 nm, 532 nm, and 1064 nm wavelengths [Winker et al., 1996]. At mission completion, nearly 45 Gbytes of data had been obtained. As the data were collected they were organized into three data sets. The largest of these data sets contained the single-shot full resolution digitized lidar signals for all three wavelengths. The other two data sets contained the instrument status data block (ISDB) and the quick look science data (QLSD). ISDB information was generated once per second and contained timing parameters and engineering data related to the health, status, and configuration of the instrument. The QLSD are 100shot averages of the 355 nm and 532 nm lidar signals and were generated at ten second intervals. As the LITE data were generated, they were output to low-rate and high-rate telemetry streams. The low-rate data contained the ISDB and QLSD. The lowrate data were transmitted to the ground by the Shuttle S-band system through the Tracking and Data Relay Satellite System (TDRSS). The high-rate data contained the full resolution digitized lidar signals for all three wavelengths, the ISDB, and QLSD. The high-rate data were transmitted in real time by the Ku-band system through TDRSS downlink to the LITE operations center at the Johnson Space Center (JSC). High-rate data were only obtained when the orbiter and TDRSS telemetry link coincided with the real-time operations of LITE. The low-rate data were backed up by a Shuttle recorder during periods when the telemetry link was unavailable, and the entire lowrate data stream was transferred to the ground over the course of the mission. A total of 53 hours of lowrate data and 45.5 hours of high-rate data were acquired. All of the LITE raw telemetry data have been archived at the NASA Langley Research Center (LaRC), and the LITE high-rate data have been processed to the level 1 data product. This paper describes the data processing steps required to convert the LITE raw, high-rate telemetry data to the LITE level 1 data product.

Powell, Kathleen A.↗

X-33 Integrated Test Facility Extended Range Simulation

In support of the X-33 single-stage-to-orbit program, NASA Dryden Flight Research Center was selected to provide continuous range communications of the X-33 vehicle from launch at Edwards Air Force Base, California, through landing at Malmstrom Air Force Base Montana, or at Michael Army Air Field, Utah. An extensive real-time range simulation capability is being developed to ensure successful communications with the autonomous X-33 vehicle. This paper provides an overview of various levels of simulation, integration, and test being developed to support the X-33 extended range subsystems. These subsystems include the flight termination system, L-band command uplink subsystem, and S-band telemetry downlink subsystem.

Sharma, Ashley↗

Cassini/Huygens Science Instruments, Spacecraft, and Mission

The Cassini spacecraft will take 18 scientific instruments to Saturn. After launch and a seven-year cruise, Cassini will arrive at Saturn and separate into a Saturn orbiter and an atmospheric probe, called Huygens, which will descend to the surface of Titan. The orbiter will orbit the planet for four years, making close flybys of five satellites, including multiple flybys of Titan. Communication with Earth is at X-band; the maximum downlink rate from Saturn is 166 x 10(exp 3) bps. Orbiter instruments are body mounted; the spacecraft must be turned to point some of them toward objects of interest. The orbiter carries 12 instruments. Optical instruments provide imagery and spectrometry. Radar supplies imaging, altimetry, and radiometry. Radio links contribute information about intervening material and gravity fields. Other instruments measure electromagnetic fields and the properties of plasma, energetic particles, and dust particles. The probe is spin stabilized. It returns data via an S-band link to the orbiter. The probe's six instruments include sensors to determine atmospheric physical properties and composition. Radiometric and optical sensors will produce data on thermal balance and obtain images of Titan's atmosphere and surface. Doppler measurements between probe and orbiter will provide wind profiles. Surface sensors will measure impact acceleration, thermal and electrical properties, and, if the surface is liquid, density and refractive index. This design will enable Cassini to determine the composition; the physical, morphological, and geological nature; and the physical and chemical processes of the atmospheres, surfaces, and magnetosphere of the Saturnian system. This paper briefly describes the Cassini mission and spacecraft and, in somewhat more detail, the scientific instruments.

Jaffe, Leonard D.↗

Pioneer Venus Orbiter Ultraviolet Spectrometer: Operations and Data Analysis

The Pioneer Venus spacecraft orbited Venus 5,055 times between 4th December 1978 and 6th October 1992, before entering Venus' atmosphere and burning up on the latter date. On 255 of these orbits, science operations were suspended because of superior conjunction (Venus' proximity to the Sun as seen from Earth). Of the remaining 4800 orbits, about 85% yielded good-quality OUVS science data; 15% were lost to various problems, including loss of uplink (commands) to and downlink (data) from the spacecraft, errors in commanding OUVS, and one or other of the two instrument anomalies mentioned below.

Stewart, A. I. F.↗

One Year Report for SAMS and OARE on STS-73/USML-2

The Second United States Microgravity Laboratory (USML-2) payload flew on the orbiter Columbia on mission STS-73 from October 20 to November 5, 1995. The USML-2 payload on STS-73 was dedicated to microgravity experiments. Two accelerometer systems managed by the NASA Lewis Research Center (LeRC) flew to support these experiments, namely the Orbital Acceleration Research Experiment (OARE) and the Space Acceleration Measurements System (SAMS). OARE downlinked real-time quasi-steady acceleration data, which were provided to the investigators. The SAMS recorded higher frequency data onboard for post-mission analysis. The Principal Investigator Microgravity Services (PIMS) project at NASA LeRC supports principal investigators of microgravity experiments as they evaluate the effects of varying acceleration levels on their experiments. A summary report was prepared by PIMS to furnish interested experiment investigators with a guide to evaluate the acceleration environment during STS-73, and as a means of identifying areas which require further study. The summary report provides an overview of the STS-73 mission, describes the accelerometer systems flown on this mission, discusses some specific analyses of the accelerometer data in relation to the various activities which occurred during the mission, and presents plots resulting from these analyses as a snapshot of the environment during the mission. Numerous activities occurred during the STS-73 mission that are of interest to the low-gravity community. Specific activities of interest during this mission were crew exercise, payload bay door motion, Glovebox fan operations, water dumps, Ku band antenna activity, orbital maneuvering system, and primary reaction control system firings, and attitude changes. The low-gravity environment related to these activities is discussed in the summary report.

Hakimzadeh, Roshanak↗

STS-88 Day 02 Highlights

On this second day of the STS-88 mission, the flight crew, Commander Robert D. Cabana, Pilot Frederick W. Sturckow, and Mission Specialists Nancy J. Currie, James H. Newman, Jerry L. Ross, and Sergei Krikalev are awakened with the song "Get Ready" by the Temptations. Ross and Newman perform a checkout of the SAFER or Simplified Aid for EVA Rescue unit. SAFER is a mini maneuvering system that can provide self-rescue capability for a spacewalker if they inadvertently become separated from the spacecraft during a spacewalk. The crew then downlinks video taken inside the crew cabin during their ascent to orbit.

Source record↗

An Integrated Architecture for Onboard Spacecraft

As increasingly complex scientific and environmental observation spacecraft are deployed, the burden on the downlink assets, and ground-based systems complexity and cost is becoming a major problem. Already, the limitations of communications bandwidth and processing throughput limit the science data gathering, both in volume and in rate. This poses a dilemma to the scientist experimenter forcing choices between data collection and bandwidth/processing/archiving. Advances in ground based processing and space-to-Earth links have fallen behind the requirements for observation data, at increasing rates, over the last few decades. As NASA achieves its 40th anniversary, the ability to observe and capture phenomena of theoretical and practical interest to life on Earth far outstrips the ability to transfer, process, or store these data. NASA recognizes the need to invest on technological advancements that will enable both the space and ground systems to address the limitations. Spacecraft onboard computing power is a clear one. The capability of creating data products onboard the spacecraft adds a new level of flexibility to address the more demanding observation needs. Current spacecraft computing power is limited and incapable of addressing the needs of the new generation of observation satellites because extensive onboard data processing is required. Traditional spacecraft architectures only collect, package, and transmit to Earth the data acquired by multiple instruments. Conversely, the experience on developing ground data systems shows the need for high performance computing systems to process and create information from the instrumentation data. The expectation is that supercomputing technology is required to enable spacecraft to create information onboard. Moving supercomputing capability onboard spacecraft requires an approach that considers an integrated data architecture. Otherwise, it may simply convert a compute-bound problem into a communications bound problem, as has been shown numerous times in the context of massively parallel architectures. What is left to determine are the technologies that will enable spacecraft high performance computing.

Figueiredo, Marco A.↗

NASA Langley Teacher Resource Center at the Virginia Air and Space Center

Nation's education goals through expanding and enhancing the scientific an technological competence of students and educators. To help disseminate NASA instructional materials and educational information, NASA's Education Division has established the Educator Resource Center Network. Through this network (ERCN), educators are provided the opportunity to receive free instructional information, materials, consultation, and training workshops on NASA educational products. The Office of Education at NASA Langley Research Center offers an extension of its Precollege Education program by supporting the NASA LARC Educator Resource Center at the Virginia Air & Space Center, the official visitor center for NASA LARC. This facility is the principal distribution point for educators in the five state service region that includes Virginia, West Virginia, Kentucky, North Carolina and South Carolina. The primary goal, to provide expertise and facilities to help educators access and utilize science, mathematics, and technology instructional products aligned with national standards and appropriate state frameworks and based on NASA's unique mission and results, has been accomplished. This ERC had 15,200 contacts and disseminated over 190,000 instructional items during the period of performance. In addition the manager attended 35 conferences, workshops, and educational meetings as an GR, presenter, or participant. The objective to demonstrate and facilitate the use of educational technologies has been accomplished through the following: The ERC's web page has been developed as a cyber-gateway to a multitude of NASA and other educational resources as well as to Our own database of current resource materials. NASA CORE CD-ROM technology is regularly demonstrated and promoted using the center's computers. NASA TV is available, demonstrated to educators, and used to facilitate the downlinking of NASA educational programming.

Maher, Kim L.↗

A Photo Album of Earth Scheduling Landsat 7 Mission Daily Activities

Landsat7 is a member of a new generation of Earth observation satellites. Landsat7 will carry on the mission of the aging Landsat 5 spacecraft by acquiring high resolution, multi-spectral images of the Earth surface for strategic, environmental, commercial, agricultural and civil analysis and research. One of the primary mission goals of Landsat7 is to accumulate and seasonally refresh an archive of global images with full coverage of Earth's landmass, less the central portion of Antarctica. This archive will enable further research into seasonal, annual and long-range trending analysis in such diverse research areas as crop yields, deforestation, population growth, and pollution control, to name just a few. A secondary goal of Landsat7 is to fulfill imaging requests from our international partners in the mission. Landsat7 will transmit raw image data from the spacecraft to 25 ground stations in 20 subscribing countries. Whereas earlier Landsat missions were scheduled manually (as are the majority of current low-orbit satellite missions), the task of manually planning and scheduling Landsat7 mission activities would be overwhelmingly complex when considering the large volume of image requests, the limited resources available, spacecraft instrument limitations, and the limited ground image processing capacity, not to mention avoidance of foul weather systems. The Landsat7 Mission Operation Center (MOC) includes an image scheduler subsystem that is designed to automate the majority of mission planning and scheduling, including selection of the images to be acquired, managing the recording and playback of the images by the spacecraft, scheduling ground station contacts for downlink of images, and generating the spacecraft commands for controlling the imager, recorder, transmitters and antennas. The image scheduler subsystem autonomously generates 90% of the spacecraft commanding with minimal manual intervention. The image scheduler produces a conflict-free schedule for acquiring images of the "best" 250 scenes daily for refreshing the global archive. It then equitably distributes the remaining resources for acquiring up to 430 scenes to satisfy requests by international subscribers. The image scheduler selects candidate scenes based on priority and age of the requests, and predicted cloud cover and sun angle at each scene. It also selects these scenes to avoid instrument constraint violations and maximizes efficiency of resource usage by encouraging acquisition of scenes in clusters. Of particular interest to the mission planners, it produces the resulting schedule in a reasonable time, typically within 15 minutes.

Potter, William↗

X-33 Integrated Test facility, Extended Range Simulation

In support of the X-33 Single Stage To Orbit program, NASA Dryden Flight Research Center was selected to provide continuous communications coverage of the X-33 vehicle from launch, through landing at Malmstrom Air Force Base, Montana and Michaels Army Air Field, Utah. An extensive real-time range simulation capability is being developed to ensure successful communications with the autonomous X-33 vehicle. This paper will provide an overview of the various levels of simulation being developed to support the X-33 extended range subsystems. These subsystems include the Flight Termination System, L-Band command uplink subsystem and the S-Band telemetry downlink subsystem. In addition, the radar model developed provides continuous azimuth, elevation and range information based on the flight trajectory. The Dynamic Ground Station Analysis model developed by NASA Goddard Space Flight Center, calculate the received signal strength at each ground station. This model takes into consideration Radio Frequency (RF) link parameters such as frequency, antenna gain, space loss, plasma effects and the vehicle's position and attitude at any point in time during the flight path. All three RF links are then attenuated based on this calculated level and the RF signals are sent into telemetry receivers to emulate remote sites, or the power incident on the vehicle from uplinked signals. The best source received telemetry data is then passed back to the Launch and Mission Control Monitoring System (LMCMS) resident in the Operations Control Center. The LMCMS also provides the range simulation system the uplink command combined with differential GPS corrections. Later stages will require the progressive integration of actual range hardware with this simulation effort, leading to communication between telemetry, uplink and FTS antennas at NASA Dryden Flight Research Center, with vehicle antennas mounted on the Walter C. Williams Research Aircraft Integration Facility (RAIF). Decommutated Pulse Code Modulated (PCM) data is displayed on one of the four monitors that comprise the Range Safety Officer's (RSO) station. Also displayed are instantaneous impact prediction models, and Federal Aviation Administration (FAA) data for notification of other traffic in the area. Aside from initiating the flight termination command and validating communication links, the RSO station with the range simulation will be used to provide both range control and range safety officers training. The training is necessary to perform their respective functions with greater levels of confidence prior to first flight.

Sharma, Ashley↗

Solar-B X-ray Telescope (XRT) Concept Study Report

The X-ray observations from the Yohkoh SXT provided the greatest step forward in our understanding of the solar corona in nearly two decades. Expanding on the accomplishments of Yohkoh, we believe that the scientific objectives of the Solar-B mission are achieved with a significantly improved X-ray telescope (XRT) similar to the SXT. The Solar-B XRT will have twice the spatial resolution and a broader temperature response, while building on the knowledge gained from the successful Yohkoh mission. We present the scientific justification for this view, discuss the instrumental requirements that flow from the scientific objectives, and describe the instrumentation to meet these requirements. We then provide a detailed discussion of the design activities carried out during Phase A, noting the conclusions that were reached in terms of their implications for the detailed design activities which are now commencing. Details of the instrument that have changed as a result of the Phase A studied are specifically noted, and areas of concern going into Phase B are highlighted. XRT is a grazing-incidence (GI) modified Wolter I X-ray telescope, of 35cm inner diameter and 2.7m focal length. The 2048x2048 back-illuminated CCD (now an ISAS responsibility) has 13.5 micron pixels, corresponding to 1.0 arcsec and giving full Sun field of view. This will be the highest resolution GI X-ray telescope ever flown for Solar coronal studies, and it has been designed specifically to observe both the high and low temperature coronal plasma. A small optical telescope provides visible light images for co-alignment with the Solar-B optical and EUV instruments. The XRT science team is working in close cooperation with our Japanese colleagues in the design and construction of this instrument. All of the expertise and resources of the High Energy and Solar/Stellar Divisions of the Center for Astrophysics are being made available to this program, and our team will carry its full share of responsibility for mission operations, data reduction and education and public outreach. All aspects of the XRT design were reviewed during Phase A. The study focussed particularly on those aspects that have the greatest affect on instrument performance and extended lifetime, on the image quality error budget, and on the camera (mechanical and electrical) interface and the instrument mounting interfaces. The present instrument design differs in some details from that originally proposed. Selection of the XRT for Phase A study was contingent upon the removal of the camera and its associated electronics, and the acceptance of a stringent cost cap. The removal of the electronics left the XRT without control electronics for the instrument mechanisms. A mechanism controller was therefore added. The removal of the camera resulted in major complications to the integration and test plan. After many discussions, it was decided that the system would be less expensive, and the risk of unacceptable performance lower, if we include a focus mechanism. The remainder of the XRT design baseline matches the proposed configuration. Data requirements for the XRT are driven by the science plans, which are based on the physical processes in the solar outer atmosphere. Discussions to date of the XRT observing plan, both alone and in conjunction with the other Solar-B instruments, shows that the XRT needs 2 Gbits of on-board storage, at least one circulating buffer of 640 Mbits, and twelve 10- minute downlinks per day in order to carry out its required programs.

Golub, Leon↗

The Influence of Loss of Visual Cues on Pilot Performance During the Final Approach and Landing Phase of a Remotely Piloted Vehicle Mission

Remotely piloted research vehicles (RPRVS) are currently being flown from fixed-base control centers, and visual information is supplied to the remote pilot by a TV camera mounted in the vehicle. In these circumstances, the possibility of a TV failure or an interruption in the downlink to the pilot must be considered. To determine the influence of loss of TV information on pilot performance during the final approach and landing phase of a mission, an experiment was conducted in which pilots were asked to fly a fixed-base simulation of a Piper PA-30 aircraft with loss of TV information occurring at altitudes of 15.24, 30.48, and 45.72 m (50, 100, and 150 ft). For this experiment, a specially designed display configuration was presented to four pilots in accordance with a Latin square design. Initial results indicate that pilots could not ensure successful landings from altitudes exceeding 15.24 m (.50 ft) without the visual cues supplied by the TV picture.

Howard, James C.↗

STS-99 Crew Interviews: Janet L. Kavandi

This NASA JSC video release is one in a series of space shuttle astronaut interviews and was recorded Aug. 9, 1999. Mission Specialist, Janet L. Kavandi, Ph.D. provides answers to questions regarding her role in the Shuttle Radar Topography Mission (SRTM), mission objectives, which center on the three-dimensional mapping of the entire Earth's surface, shuttle imaging radar, payload mast deploy and retraction, data recording vs. downlinking, the fly cast maneuver, applications of recorded data, international participation (DLR), the National Imaging and Mapping Agency (NIMA), and EarthCam (educational middle school project). The interview is summed up by Dr. Kavandi explaining that the mission's objective, if successful, will result in the the most complete high-resolution digital topographic database of the Earth.

Source record↗

Design Description of the X-33 Avionics Architecture

In this paper, we provide a design description of the X-33 avionics architecture. The X-33 is an autonomous Single Stage to Orbit (SSTO) launch vehicle currently being developed by Lockheed Martin for NASA as a technology demonstrator for the VentureStar Reusable Launch Vehicle (RLV). The X-33 avionics provides autonomous control of die vehicle throughout takeoff, ascent, descent, approach, landing, rollout, and vehicle safing. During flight the avionics provides communication to the range through uplinked commands and downlinked telemetry. During pre-launch and post-safing activities, the avionics provides interfaces to ground support consoles that perform vehicle flight preparations and maintenance. The X-33 Avionics is a hybrid of centralized and distributed processing elements connected by three dual redundant Mil-Std 1553 data buses. These data buses are controlled by a central processing suite located in the avionics bay and composed of triplex redundant Vehicle Mission Computers (VMCs). The VMCs integrate mission management, guidance, navigation, flight control, subsystem control and redundancy management functions. The vehicle sensors, effectors and subsystems are interfaced directly to the centralized VMCs as remote terminals or through dual redundant Data Interface Units (DIUs). The DIUs are located forward and aft of the avionics bay and provide signal conditioning, health monitoring, low level subsystem control and data interface functions. Each VMC is connected to all three redundant 1553 data buses for monitoring and provides a complete identical data set to the processing algorithms. This enables bus faults to be detected and reconfigured through a voted bus control configuration. Data is also shared between VMCs though a cross channel data link that is implemented in hardware and controlled by AlliedSignal's Fault Tolerant Executive (FTE). The FTE synchronizes processors within the VMC and synchronizes redundant VMCs to each other. The FTE provides an output-voting plane to detect, isolate and contain faults due to internal hardware or software faults and reconfigures the VMCs to accommodate these faults. Critical data in the 1553 messages are scheduled and synchronized to specific processing frames in order to minimize data latency. In order to achieve an open architecture, military and commercial off-the-shelf equipment is incorporated using common processors, standard VME backplanes and chassis, the VxWorks operating system, and MartixX for automatic code generation. The use of off-the-shelf tools and equipment helps reduce development time and enables software reuse. The open architecture allows for technology insertion, while the distributed modular elements allow for expansion to increased redundancy levels to meet the higher reliability goals of future RLVs.

Reichenfeld, Curtis J.↗

First Look at Landsat-7 Mission Performance: Technical and Operational Results to Date

A primary goal of the current Landsat-7 mission, launched on April 15, 1999, is to acquire and refresh on a seasonal basis, calibrated ata sets of multispectral digital imagery of the landmass of the Earth The Enhanced Thematic Mapper Plus (ETM+) imager flown on Landsat-7 provides ground spatial resolutions in the panchromatic, reflective and emissive bands of 15, 30 and 60 meters, respectively, for a nominal scene 183 km wide by 170 km long. This mission not only builds on the invaluable 27-year continuous archive of thematic images of the Earth provided by previous Landsat satellites, it also inaugurates a new era of robust data acquisition with an emphasis on global change science. The newly developed Long Term Acquisition Plan (LTAP) is being used to optimize the systematic collection of data from all parts of the globe, populating the U.S.-held archive at the USGS EROS Data Center (EDC) with over 90,000 Landsat scene per year . An additional 73,000 Images are expected to be acquired each year by several international ground stations, for a total downlink of Landsat7 data in excess of 100 terabytes per year. Nearly 20,000 scan of Landsat-7 ETM+ data have already been acquired in the first 100 days of the mission. Early results derived from assessments of the ETM+ instrument, the spacecraft, and the ground processing systems indicate that the image quality is outstanding, clearly the best ever provided by any Landsat mission. Sensor radiometric background stability after the first 100 days in orbit is approximately 0.1 percent. Stability of the Full Aperture Solar Calibrator is approximately 0.3 percent, and mid-scale per pixel noise is approximately 0.6 percent. A ground processing system has been implemented at EDC which is capable of capturing, processing and archiving 250 Landsat scenes 9 per day, and delivering 100 scene products to seems each day. The cost of a systematically-processed Level 1 product has been dropped dramatically to $600, end there is no longer any copyright protection an the data. The net result is that the use of Landsat ETM+ data is expected to grow dramatically, and this growth is expected to benefit all facets of the land remote sensing community.

Williams, Darrel L.↗

Optical Communications Study for the Next Generation Space Telescope

The Next Generation Space Telescope (NGST), part of NASA's Origins program, is a follow on to the Hubble Space Telescope expected to provide timely new science along with answering fundamental questions. NGST is a large diameter, infrared optimized telescope with imaging and spectrographic detectors which will be used to help study the origin of galaxies. Due to the large data NGST will collect, Goddard Space Flight Center has considered the use of optical communications for data downlink. The Optical Communications Group at the Jet Propulsion Laboratory has performed a study on optical communications systems for NGST. The objective of the study was to evaluate the benefits gained through the use of optical communication technologies. Studies were performed for each of four proposed NGST orbits. The orbits considered were an elliptical orbit about the semi stable second Lagrangian point, a 1 by 3 AU elliptic orbit around the sun, a 1 AU drift orbit, and a 1 AU drift orbit at a 15 degree incline to the ecliptic plane. An appropriate optical communications system was determined for each orbit. Systems were evaluated in terms of mass, power consumption, size, and cost for each of the four proposed orbits.

Ceniceros, Juan M.↗

A Flight/Ground/Test Event Logging Facility

The onboard control software for spacecraft such as Mars Pathfinder and Cassini is composed of many subsystems including executive control, navigation, attitude control, imaging, data management, and telecommunications. The software in all of these subsystems needs to be instrumented for several purposes: to report required telemetry data, to report warning and error events, to verify internal behavior during system testing, and to provide ground operators with detailed data when investigating in-flight anomalies. Events can range in importance from purely informational events to major errors. It is desirable to provide a uniform mechanism for reporting such events and controlling their subsequent processing. Since radiation-hardened flight processors are several years behind the speed and memory of their commercial cousins, and since most subsystems require real-time control, and since downlink rates to earth can be very low from deep space, there are limits to how much of the data can be saved and transmitted. Some kinds of events are more important than others and should therefore be preferentially retained when memory is low. Some faults can cause an event to recur at a high rate, but this must not be allowed to consume the memory pool. Some event occurrences may be of low importance when reported but suddenly become more important when a subsequent error event gets reported. Some events may be so low-level that they need not be saved and reported unless specifically requested by ground operators.

Dvorak, Daniel↗

An AI Approach to Ground Station Autonomy for Deep Space Communications

This paper describes an architecture for an autonomous deep space tracking station (DS-T). The architecture targets fully automated routine operations encompassing scheduling and resource allocation, antenna and receiver predict generation. track procedure generation from service requests, and closed loop control and error recovery for the station subsystems. This architecture has been validated by the construction of a prototype DS-T station, which has performed a series of demonstrations of autonomous ground station control for downlink services with NASA's Mars Global Surveyor (MGS).

Fisher, Forest↗