Results for “CFD” — Page 37

NASA NTRSDate not supplied

CFD Evaluation Of Sustainable Aviation Fuel Blends for Commercial Supersonics Technology

An overview is provided of a CFD study on the impacts of fuel blends on NOx emissions and flame structure in an axially staged combustor operating at a supersonic cruise condition. The Open version of the National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with various blending ratios of an ‘average’ Jet-A (A2) and Gevo Alcohol-to-Jet (C1) for RTRC’s Axially Controlled Stoichiometry (ACS) combustor. The predicted flame structures in the ACS combustor with three different blending ratios of the A2 and C1 fuel were very similar. The predicted NOx emissions for all fuel blends were within 10% of the experimentally measured range of NOx emissions for 100% A2 fuel.

gas turbine combustion↗

NASA NTRSDate not supplied

Analysis of Mars 2020 Entry with Coupled Material Response and CFD

When computing the response of an ablating thermal protection system during entry, the aerothermal environment and material response are traditionally computed independently, with the introduction of a blowing correction term in the material response model to account for the outgassing of char and pyrolysis gases. This study presents an approach, where the pyrolysis blowing gases, calculated within the PATO material response code [1], are integrated into the DPLR hypersonic CFD code [2] via a blowing boundary condition. This methodology employs an iterative process, whereby the blown pyrolysis gas products from PATO are incorporated into DPLR, refining surface heating predictions. The NEQAIR code is used to compute radiative heating [3]. The method is applied in computing 3D material response of the Mars 2020 entry. When compared with uncoupled material response, the coupled simulations show a lower surface heat flux initially and a higher heat flux at peak heating as shown in Fig. 1. This is in agreement with previous work using a sphere case with environments from MSL [4].

Heat Transfer↗

NASA NTRSDate not supplied

In Pursuit of CFD-based Wind Tunnel Calibrations

Computational fluid dynamic simulations of models tested in wind tunnels require a high level of fidelity and accuracy, particularly for the purposes of CFD validation efforts. Considerable effort is required to ensure a sufficient characterization of both the physical geometry of the wind tunnel, the thermodynamics of the tunnel, and flow conditions in the test section. The condition setting process among subsonic wind tunnels, closed or open throat, is generally the same, though they can differ in specific details of the thermodynamics. The derivation, application, and error estimation of condition setting and calibration is discussed. Computational flow solutions of the high-speed leg of the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel are used to evaluate the calibration process and discuss calibration curve sensitivities. Duplicating the characteristics of a particular wind tunnel is difficult at best. A calibration curve derived from the computational method is the most consistent method to use for tunnel condition setting.

wind tunnel↗

NASA NTRSDate not supplied

Analysis of Mars 2020 Entry with Coupled Material Response and CFD

When computing the response of an ablating thermal protection system during entry, the aerothermal environment and material response are traditionally computed independently, with the introduction of a blowing correction term in the material response model to account for the outgassing of char and pyrolysis gases. This study presents an approach, where the pyrolysis blowing gases, calculated within the PATO material response code, are integrated into the DPLR hypersonic CFD code via a blowing boundary condition. This methodology employs an iterative process, whereby the blown pyrolysis gas products from PATO are incorporated into DPLR, refining surface heating predictions. The NEQAIR code is used to compute radiative heating. The method is applied in computing 3D material response of the Mars 2020 entry. When compared with uncoupled material response, the coupled simulations show a lower surface heat flux initially and a higher heat flux at peak heating as shown in Fig. 1. This is in agreement with previous work using a sphere case with environments from MSL.

Heat Transfer↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Validation of the Hypersolve CFD Solver for Entry Descent and Landing Applications

The functional equivalence of the HyperSolve unstructured edge-based, finite-volume computational fluid dynamics code to the Langley Aerothermodynamic Upwind Relaxation Algorithm multiblock structured grid code is documented for applications of interest to the Entry, Descent, and Landing community. A suite of cases using a range of thermochemical gas models on relevant vehicle configurations were analyzed with both codes and the results compared. A tolerance of ±4% difference in surface pressure and surface heat flux from a benchmark LAURA solution was used as the criterion for functional equivalence, and comparisons of flowfield quantities are also included to verify that the thermochemical nonequilibrium capabilities in HyperSolve match those of the LAURA code. The functional equivalence of the HyperSolve unstructured edge-based finite-volume computational fluid dynamics (CFD) code to the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) multiblock structured grid code is documented for applications of interest to the Entry, Descent, and Landing (EDL) community. A suite of cases using a range of thermochemical gas models on EDL-relevant vehicle configurations were analyzed with both codes and the results compared. A tolerance of ±4% difference in surface pressure and surface heat flux from a benchmark LAURA solution was used as the criterion for functional equivalence, and comparisons of flow field quantities are also included to verify that the thermochemical nonequilibrium capabilities in HyperSolve match those of the LAURA code. In general, HyperSolve predictions for surface pressure and surface heat flux are in close agreement with those predicted by LAURA.

hypersolve↗

NASA NTRSDate not supplied

CFD Predictions of Fluctuating Pressure Environments on NASA’s SLS Ascent Unsteady Aerodynamics Wind Tunnel Test

This paper details work that is being conducted on predicting fluctuating pressure environments on NASA launch vehicles using computational fluid dynamics (CFD). The accurate characterization of these aeroacoustics environments is necessary in the analysis of vehicle structural health and aerodynamic performance and in the vehicle design process. High-fidelity simulations of the unsteady flow over NASA’s SLS Ascent Unsteady Aerodynamics wind tunnel Test (AUAT) using the hybrid Reynolds-averaged Navier-Stokes (RANS)-large eddy simulations (LES) methodologies in Mississippi States’ Loci/CHEM solver are presented. The two available methods, Nelson-Nichols and dynamic hybrid RANS-LES (DHRL), are compared head-to-head on identical grids at two Mach numbers. At the high-subsonic Mach number, locally supersonic flow expanding over a shoulder induces a separation-reattachment system that is predicted poorly by the Nelson-Nichols method due to an under-prediction in unsteady content. The DHRL solution predicts the spatial extent and frequency domain response of this system well but under-predicts the peak noise levels due to a delay in the RANS-to-LES transition. At the low-supersonic Mach number, compression corner dynamics dominate the unsteady flow. While the Nelson Nichols solution captures this phenomenon well, another solution on a refined grid indicates that some model stress depletion is occurring. The DHRL solution again performs well at this Mach number and matches the wind tunnel data fairly closely, but perhaps most impressively, is fairly agnostic to increasing grid resolution. The findings in this paper are expected to be generally applicable and will be used to guide the prediction of aeroacoustics environments of other NASA launch vehicles.

CFD↗

NASA NTRSDate not supplied

Validation of the HyperSolve CFD Solver for Entry Descent and Landing Applications

The functional equivalence of the HyperSolve unstructured edge-based, finite-volume computational fluid dynamics code to the Langley Aerothermodynamic Upwind Relaxation Algorithm multiblock structured grid code is documented for applications of interest to the Entry, Descent, and Landing community. A suite of cases using a range of thermochemical gas models on relevant vehicle configurations were analyzed with both codes and the results compared. A tolerance of ±4% difference in surface pressure and surface heat flux from a benchmark LAURA solution was used as the criterion for functional equivalence, and comparisons of flowfield quantities are also included to verify that the thermochemical nonequilibrium capabilities in HyperSolve match those of the LAURA code. The functional equivalence of the HyperSolve unstructured edge-based finite-volume computational fluid dynamics (CFD) code to the Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) multiblock structured grid code is documented for applications of interest to the Entry, Descent, and Landing (EDL) community. A suite of cases using a range of thermochemical gas models on EDL-relevant vehicle configurations were analyzed with both codes and the results compared. A tolerance of ±4% difference in surface pressure and surface heat flux from a benchmark LAURA solution was used as the criterion for functional equivalence, and comparisons of flow field quantities are also included to verify that the thermochemical nonequilibrium capabilities in HyperSolve match those of the LAURA code. In general, HyperSolve predictions for surface pressure and surface heat flux are in close agreement with those predicted by LAURA.

hypersolve↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Performance Characteristics of a Boundary Layer Ingesting Inlet - Distortion Tolerant Fan Through CFD Code Coupling

A method of constructing a high-fidelity simulation using two NASA CFD codes, Launch Ascent and Vehicle Aerodynamics (LAVA), which is the general-purpose solver, and a turbomachinery specific code NASA-TURBO (TURBO), will be presented. Validation of the code coupling is performed through comparison to experimental data obtained in the 2017 wind tunnel test of NASA’s Boundary Layer Ingesting Inlet - Distortion Tolerant Fan (BLI2DTF). For the simulation, the external flow field is computed by LAVA utilizing a steady-state Reynolds-averaged Navier-Stokes (RANS) methodology. Data from LAVA is exchanged with TURBO, which simulated the propulsor utilizing an unsteady-RANS methodology. A sensitivity analysis is performed using averaged and instantaneous data transfer between the two codes, as well as varying the amount of simulation time TURBO computes between updates. The results of the coupled simulations appear to replicate the BLI2DTF experiment correctly. Static pressure taps leading into and around the nacelle, total pressure ratio and efficiency of the propulsor, and profiles of total temperature, pressure, and Mach number at the rear measurement plane, aft of the propulsor, are in good agreement with experimental data. These results provide confidence that the coupled simulation is behaving in a physically realizable manner.

CFD↗

NASA NTRSDate not supplied

CFD Evaluation of Radial Airflow Lean Direct Injectors for Commercial Supersonics Technology

An overview is provided of the impact on NOx emissions of replacing the six axial airflow Main swirlers of a seven-element lean-direct injection (LDI) module with radial airflow swirlers. The CFD study was motivated by the goal of reducing EINOx emissions of a combustor operating at supersonic cruise condition to a nominal value of 10 or below. The Open version of the National Combustion Code (OpenNCC) was used to perform two-phase reacting flow computations with various radial airflow swirler LDI flametube designs with an ‘average’ Jet-A (A2) fuel. The predicted EINOx emissions for the various radial airflow designs evaluated with OpenNCC were within 20% of each other, and 25% lower than current LDI injector designs using axial airflow swirlers.

gas turbine combustion↗

NASA NTRSDate not supplied

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

NASA NTRSDate not supplied

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

NASA NTRSDate not supplied

Intermittency Model for Coupled CFD-Stability Transition Analysis in Hypersonic Flow

Accurate prediction of aerothermodynamic loads on hypersonic vehicles requires precise modeling of surface quantities across the boundary layer transition zone. The peak heating loads and total heat transfer are determined by parameters such as the transition zone length and the magnitude of potential overshoots in heat flux and skin friction beyond their respective values in fully turbulent flows. While previous studies on CFD integrated transition modeling using linear stability correlations have shown promise in modeling these features, they did not develop an intermittency model for hypersonic flows. This paper presents a data-driven approach to develop a model of this type by correlating experimental transition data with the relevant flow parameters. The resulting model demonstrates significant improvements over previous low-speed models in terms of predicting heat transfer distributions during the transition process associated with first and second mode instabilities in axisymmetric high-speed flows. Separate correlations for flight and ground test conditions are developed, and the potential to combine these correlations is discussed.

Transition↗

NASA NTRS2025

CFD Validation and Scaling of a Condenser Used in an ISRU Propellant Production System

This work develops a Computational Fluid Dynamics (CFD) model of a Commercial-Off-The-Shelf (COTS) condenser used for ground-based testing of an In-Situ Resource Utilization (ISRU) propellant production system. STAR-CCM+ was used to simulate water condensing through the condenser downstream of a methanation reactor. The computational data of the digital model is validated with test cases using nitrogen and water in ambient conditions. After validation with the test data, the digital model can be used to predict scale at higher production targets. The StarCCM+ simulation of the digital model shows good agreement with the test data provided. From the simulation, the condensation rate calculated was 18.3 g/hr and the process gas mass flow rate was 709.2 g/hr. The test data measured an average 16.9 g/hr condensation rate and 693.6 g/hr process gas mass flow rate. The simulation shows a 7.3% error in the water condensation and 2.2% error in the process gas at the outlet.

Condenser↗

NASA NTRS2025

CFD Validation of a Methanation Reactor With Cooling Jacket Used in an ISRU Propellant Production System

A digital model of an OxEon Energy methanation reactor (with a cooling jacket) planned for use in a NASA designed In-Situ Resource Utilization (ISRU) propellant production system was developed by the UTEP Aerospace Center using STAR-CCM+ software, a Siemens Computational Fluid Dynamics (CFD) package. The reactor digital model created includes two primary components: (i) a cooling jacket that maintains the required reactor chamber surface temperature and (ii) a reactor core chamber where the exothermic methanation reactions occur. The StarCCM+ digital model has two objectives: (i) maintain the surface temperature of the reactor below a set value so that the extra heat accumulation does not melt or crack the chamber, and (ii) produce the desired amount of methane (CH4) according to test cases completed by OxEon Energy for NASA JSC. The computational digital model was validated with the test data enabling the cooling jacket scale to be predicted based on the reactor's operating temperature. The StarCCM+ simulation of the digital model shows a good agreement with the cooling jacket performance and the CH4 production. One test case for the cooling jacket maintained the reactor wall temperature around 310 °C was validated and the reactor produced 185 g/hr CH 4 .

ISRU↗

DOE OSTI2020

Achievements and Ongoing Challenges for advanced CFD Boiling Closure Model Development using Physical Insights from Validation-Oriented High-Fidelity Boiling Experiment

The fundamental understanding of the boiling-associated heat transfer, including sliding bubble effect, is still challenging despite the intensive research for decades in both experimental and computational boiling research communities. One of the main difficulties of boiling experiment come from the fact that direct observation of the underlying principle through experiment is very difficult due to the high complexity of the boiling phenomenon. Also, since the heat transfer characteristics associated with boiling is the result of non-linear interaction of various physical parameters coupled to each other, it is challenging to find the relationship between the parameters for modeling. This paper discusses the authors’ past and ongoing boiling research under CASL (Consortium for Advanced Simulation of Light Water Reactors) program, including the efforts to overcome the difficulties of boiling measurement and model development. In particular, we focus on describing the major achievements, lessons learnt, and ongoing challenges for the CFD boiling closure model development based on the high-fidelity subcooled flow boiling experiment at Texas A&M University (TAMU). The major research achievements discussed through this paper include (i) novel boiling measurement strategy and high-fidelity validation data production, (ii) dedicated effort to identify the critical measurement issues in boiling experiment, (iii) new physical insight into sliding bubble heat transfer mechanisms, and (iv) new boiling closure model development. Discussion is also made on the ongoing challenges for the boiling closure model development and the future research plan based on the lessons learnt.

42 ENGINEERING↗

DOE OSTI2025

Air-Cooled RCCS CFD Modeling Validation 2025

Slide deck for the Advanced Reactor Technologies Gas Cooled Reactor (ART-GCR) program review. The slides show the progress on the air-cooled reactor cavity cooling system (RCCS) CFD validation work. The validation of the air-cooled RCCS is performed using the experimental facility at the University of Wisconsin-Madison. The slide deck provides a progress update on this year's achievements. The natural convection tests under uniform power are modeled and compared with the experimental results. The results show good agreement with the experimental results. A sensitivity study on the RANS turbulence models is performed. Additionally, the contribution of radiative and convective heat transfer within the heated cavity is calculated and compared to forced convection setups.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗