Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AGGLOMERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Microstructural Analysis of Cadmium Whiskers on Long-Term-Used Hardware

A survey of cadmium plated field return hardware showed ubiquitous cadmium whisker growth. The most worn and debris-covered hardware showed the densest whisker growth. Whiskers were often found growing in agglomerates of nodules and whiskers. The hardware was rinsed with alcohol to transfer whiskers and debris from the hardware to a flat stub. Fifty whiskers were studied individually by scanning electron microscopy (SEM), including energy dispersive spectroscopy (EDS) and electron backscatter diffraction (EBSD). Most of the whiskers were single crystal, though three were found to contain grain boundaries at kinks. The whiskers ranged from 5 to 600 μm in length and 80 pct showed a $<\bar{1} 2 \bar{1} 0>$ type growth direction. This growth direction facilitates the development of low energy side faces of the whisker, (0001) and {1010}.

36 MATERIALS SCIENCE↗

Rapid Identification of Calcium Aluminate Inclusions in Steels Using Cathodoluminescence Analysis

We propose a method to identify calcium aluminate inclusions in calcium-treated aluminum-killed steels (Ca{sub 12}Al{sub 14}O{sub 33}, CaAl{sub 4}O{sub 7}, CaAl{sub 12}O{sub 19}, and Al{sub 2}O{sub 3}) using cathodoluminescence (CL) analysis. Such inclusions result in nozzle clogging and melting of the stopper rod during continuous casting. We obtain CL images and CL spectra of calcium aluminate inclusions in model samples of calcium-treated aluminum-killed steel. The model samples are prepared by heating mixtures of Fe powder, Al powder, and Ca shot at 1550 °C in an argon atmosphere. On the basis of the CL colors and CL spectra of the calcium aluminate inclusions, we demonstrate that it is possible to distinguish Ca{sub 12}Al{sub 14}O{sub 33}, CaAl{sub 4}O{sub 7}, CaAl{sub 12}O{sub 19}, and Al{sub 2}O{sub 3} inclusions from CaAl{sub 2}O{sub 4} and Ca{sub 3}Al{sub 10}O{sub 18} inclusions, which do not cause nozzle clogging and melting of the stopper rod, by comparing CL images obtained using digital cameras with and without a built-in filter. The acquisition times for the CL images are less than 10 seconds. Thus, the method we present here can be applied for the rapid detection of harmful calcium aluminate inclusions during continuous casting. The CL spectra also provide basic information to specify compositions in agglomerated calcium aluminate inclusions.

36 MATERIALS SCIENCE↗

Tuning Weld Metal Mechanical Responses via Welding Flux Optimization of TiO{sub 2} Content: Application into EH36 Shipbuilding Steel

A series of TiO{sub 2}-containing basic-fluoride-type agglomerated fluxes was applied to join EH36 shipbuilding steel under high heat input SAW. The effects of TiO{sub 2} content on composition, microstructure features, inclusions characteristics, and mechanical properties of ensuing weld metals (WMs) were systematically investigated. 6 wt pct TiO{sub 2} leads to the most optimal mechanical properties. Such behaviors were elucidated via transfer of alloying elements, which enables a good combination of acicular ferrites (AFs) and accompanying microstructures.

36 MATERIALS SCIENCE↗

Effects of TiB{sub 2} Particle and Short Fiber Sizes on the Microstructure and Properties of TiB{sub 2}-Reinforced Composite Coatings

In this study, particle and short fiber-reinforced titanium matrix composite coatings are prepared via laser in situ technique using (0.5 and 50 μm) TiB{sub 2} and Ti powder as cladding materials. The microstructure and properties of the composite coatings are studied, and the changing mechanism of the microstructure is discussed. The results reveal that particle agglomeration is prone to appear with using fine TiB{sub 2} particles. Decomposition of the particles preferentially occurs with using coarse TiB{sub 2} particles. The cracks and pores on the surface of the coating are formed at a lower laser energy density. With the increase in the laser energy density, cracking on the surface of the coating diminishes, but the coating exhibits depression behavior. The depression extent of the coating using fine TiB{sub 2} particle as the reinforcement is much less than that of the coating using coarse TiB{sub 2} particle. Moreover, the size of the aggregate and the tendency of cracking can be reduced with the increase in Ti addition. Meanwhile, short TiB fiber bundles are formed by the diffusion mechanism of rod aggregate, and randomly oriented TiB short fibers are formed mainly by the dissolution–precipitation mechanism of fine TiB{sub 2} particles. Moreover, the growth of short TiB fibers can be in an alternating manner between B27 and Bf structures. The micro-hardness and wear resistance of the coatings are evidently higher than that of the titanium alloy substrate. The wear resistance of the large size TiB{sub 2} coating is higher than that of the small size TiB{sub 2} coating under the condition of low load.

36 MATERIALS SCIENCE↗

Synthesis of Self-Assembled rGO-Co{sub 3}O{sub 4} Nanoparticles in Nanorods Structure for Supercapacitor Application

A simple hydrothermal process was used to design self-assembled Co{sub 3}O{sub 4} nanoparticles in nanorod structure in the presence of graphene oxide as a template. The as-prepared Co{sub 3}O{sub 4} sample in a loose powder form was calcined at 450 °C to get the well-crystalline phase of the same compound. The obtained Co{sub 3}O{sub 4} powder sample was characterized by using the powder XRD and SEM. The XRD pattern shows totally nine distinct reflection peaks of (111), (220), (311), (222), (400), (422), (511), (440), and (533) planes. The most intense peaks were chosen to evaluate the structural parameters. The lattice parameters (a), volume (V), and density (ρ) of the samples are 8.09 Å, 529.47 Å{sup 3}, 6.06 g/cc, which are comparable to the value of lattice parameter (a = 8.056 Å), volume (V = 528.30 Å{sup 3}), and density (ρ = 6.055 gm/cc) for bulk Co{sub 3}O{sub 4}. The average size of the Co{sub 3}O{sub 4} nanoparticles is 14 nm which is smaller than the SEM size of 50 nm corresponding to the agglomeration of tiny particles. Further, the formation of Co{sub 3}O{sub 4} nanoparticles were also confirmed by obtaining the band at 569, 1334,1337, 1566, and 3397 cm{sup −1} in FTIR spectrum. Totally five characteristics peaks from Co{sub 3}O{sub 4} at 182.57, 456.49, 505.84, 605.80, and 618.02 cm{sup −1} and peaks from GO-Co{sub 3}O{sub 4} at 182.57, 483.44, 505.84, 605.80, and 618.02 cm{sup −1} corresponding to F{sub 2g}, E{sub g}, F{sub 2g}, F{sub 2g,} and A{sub g} modes of the crystalline Co{sub 3}O{sub 4}, respectively, in the Raman spectra. In the case of GO-Co{sub 3}O{sub 4} composite, low-intensity peaks of D and G bands are observed. The specific capacitance in rGO-Co{sub 3}O{sub 4} nanocomposite is about 65.15 Fg{sup −1}.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A Study on Thermal Conductivity and Stability of Nanofluids Containing Chemically Synthesized Nanoparticles for Advanced Thermal Applications

This study presents easy methods of synthesizing silver (Ag) and copper (Cu) nanoparticles through chemical route in an aqueous medium under atmospheric condition at ambient temperature. The synthesized nanoparticles have been characterized with different techniques, such as x-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, energy-dispersive x-ray spectroscopy, high-resolution transmission electron microscopy, UV–visible spectroscopy and dynamic light scattering measurements. Experimental observations have revealed the absence of any metal oxide layer around the nanoparticles which are found to remain stable under ambient conditions. The featured properties, such as narrow size distribution, stability, make these nanoparticles potential candidates for the synthesis of effective nanofluids. The nanofluids have been prepared by dispersing the nanoparticles synthesized through chemical route in a suitable base fluid. The thermal conductivity of nanofluids with different nanoparticles loading has been measured by transient hot-wire method, and the results have shown that the increasing trend of enhancement in thermal conductivity with respect to nanoparticles concentration is attainable only when the nanoparticles concentration is below some limiting value depending on the type of nanofluid. Beyond this limiting value of loading, the thermal conductivity of the nanofluid decreases due to pronounced agglomeration effect. The measurements of thermal conductivity of nanofluids over varying temperatures for a given volume fraction loading of nanoparticles have shown that the thermal conductivity increases markedly with the increase in temperature. Hence, nanofluids are likely to be much more promising at high-temperature applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Synthesis and Characterization of Zeolites for Anti-corrosion Application: The Effect of Precursor and Hydrothermal Treatment

Four different hydrothermal processes were used to synthesize NaX zeolites. The effect of the precursor, hydrothermal time and temperature on the zeolite structure was investigated in this research. The results of XRD and FESEM/EDX analysis indicated the key role of aluminum sources in the amorphous content and the structure of zeolite from non-zeolite sodium aluminum silicate hydrate to favorable NaX-faujasite. Moreover, the irregular shape of agglomerated hydrogel was changed from micro- to nano-zeolite structure via the hydrothermal process of different aluminum sources. It was found that the nano-zeolites could be formed by sodium aluminate source. In addition, the synthesized zeolite particles were examined as corrosion inhibitor reservoir, considering the effect of Si/Al ratio, particle size, and amorphous content. It was shown that there is a direct relation between crystallization and ion exchange capacity. Through monitoring the behavior of bare mild steel in sodium chloride solution containing zinc cations released from the zeolite particles, it was found that the nano-zeolite particles with low Si/Al ratio can offer the most effective corrosion inhibition.

36 MATERIALS SCIENCE↗

Nonlinear Resonance Response of Porous Beam-Type Implants Corresponding to Various Morphology Shapes for Bone Tissue Engineering Applications

Having excellent biocompatibility and apatite mineralization as well as efficient mechanical properties makes bredigite as one of the most attractive bioceramics. A beam-type porous biological implant in a 3D-printed architecture is designed with micron pore size. The surface properties, morphology, and size of the composed powders are evaluated using Scherrer and Williamson-Hall equation. The effect of MNPs deposition into the bredigite bioceramics and correlation with temperature effect on roughness of the prepared bio-nanocomposite are also investigated for hyperthermia application potential. The composed powders are characterized by x-ray diffraction, and then scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis (weight change, TGA), and atomic force microscopy are utilized to evaluate the surface topography. The resonance response is the tendency of a bone scaffold to respond at prominent amplitude while the frequency of its oscillations is equal to the structure’s natural frequency of vibration. Therefore, based on the obtained mechanical properties via the experimental approach for the bio-nanocomposite material, an analytical solution based upon the multiple-timescale method is carried out to analyze the nonlinear primary resonance of a 3D-printed porous beam-type biological implant under uniform-distributed load. According to SEM observations, there are hard agglomerates in the bredigite-magnetite nanoparticles (Br-MNPs) bio-nanocomposite material with low weight fraction of MNPs. However, they are broken down by increasing the amount of MNPs. Also, it is displayed that for lower MNPs weight fraction, the height of jump phenomenon related to the nonlinear resonance response is maximum and minimum for, respectively, irregular and mesoporous shapes of morphology, but their associated forcing amplitudes related to the bifurcation points are minimum and maximum, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Microstructure and Properties of Ni-WC Composite Coatings on Their Solid Particle Erosion Behavior

Metal matrix composites (MMCs) of WC in Co or Ni matrices are widely used due to their high wear resistance. Previous studies showed that tailoring the mechanical properties through optimum WC content can significantly extend the life cycle of MMCs. In this study, composite coatings of Ni with various WC content ranging from 10 to 55 vol.% were cold sprayed using agglomerated WCNi powders and two different sizes of Ni powders, − 10 + 4 (d{sub 50} = 7 µm) referred to as Ni(7) and − 35 + 15 (d{sub 50} = 25 µm) to as Ni(25). Microstructural characterization, including the deformed structure of Ni splats and retention and distribution of WC, was performed by scanning electron microscopy (SEM). Composite coatings were subjected to solid particle erosion following ASTM G76-13 standard. At low WC content coatings, erosion occurred primarily by plastic deformation of Ni matrices and knocking out of WC particles. At high WC concentrations, network distribution of compacted WCNi particles in the matrices led to a significant drop in erosion rates of coatings, due to a change in erosion mechanism from severe cutting and plowing of Ni and WC dislodging to WCNi splats spalling. Composite coatings sprayed using finer size Ni powder were usually more erosion resistant.

36 MATERIALS SCIENCE↗

Corrosion Investigation of Zinc–Aluminum Alloy (ZA-27) Matrix Reinforced with In Situ Synthesized Titanium Carbide Particle Composites

ZA-27 alloy matrix composites comprised of different volume fractions of TiC particles as reinforcement phase were synthesized by in situ technique. Microstructural, hardness and electrochemical analysis were performed on these samples along with the base ZA-27 alloy to assess any beneficial effect of making the composites over the base alloy. It was observed that hardness increases in composites as compared to the base alloy. However, hardness of the composite reduces on increasing the reinforcement percentage. Corrosion behavior was investigated by using Tafel and EIS plots in 3.5 wt.% NaCl solution at room temperature for all the samples. The results showed increase in corrosion resistance for composites than that of base alloy. However, ZA27 + 5%TiC composite showed better results as compared to that of ZA27 + 10%TiC composite. The decreased property of ZA27 + 10%TiC composite is because of the agglomeration of particles and also by the formation of galvanic cell.

36 MATERIALS SCIENCE↗

Fabrication and Characterization of A5083-WC-Al{sub 2}O{sub 3} Surface Composite by Friction Stir Processing

In this study, WC-Al{sub 2}O{sub 3} ceramic composite was incorporated into Al5083 to produce a surface composite by friction stir processing (FSP), and the microstructure, hardness and wear properties of Al5083-WC-Al{sub 2}O{sub 3} surface composite were evaluated. Optical microscopy of FSPed samples showed grain refinement in the stir zone. The addition of WC-Al{sub 2}O{sub 3} particles as well as increase in FSP pass number had a considerable effect on grain refinement, and the grain size of Al5083 base metal of 36 µm reduced to 11 µm for Al5083-WC-Al{sub 2}O{sub 3} surface composite after four passes. The SEM observation of the surface composite revealed that the WC-Al{sub 2}O{sub 3} particles distributed homogenously in the matrix and by increasing the FSP passes, the initial agglomerates of mechanochemically synthesized WC-Al{sub 2}O{sub 3} powders could be fractured. Microhardness evaluation showed a substantial improvement by adding WC-Al{sub 2}O{sub 3} particles and increase in FSP pass number. The maximum microhardness value of 101 HV belonged to surface composite after four passes, while the microhardness of the base metal was 65 HV. Wear test results revealed enhanced tribological behavior with a similar trend of microhardness values. Scanning electron microscopy tests revealed both adhesive and abrasive wear mechanisms on the surface of the wear test specimens.

36 MATERIALS SCIENCE↗

Enhancement of Thermal Conductivity and Mechanical Properties of Cu-Reduced Graphene Oxide Composites by Interface Modification

Copper matrix composites reinforced with reduced graphene oxide (rGO) were fabricated via charge adsorption process, thermal reduction, and hot-press sintering process. We investigated the effect of rGO on the thermal conductivity, electrical conductivity, mechanical properties, and microstructure of the composites. By controlling the reaction process, copper on the rGO surface was oxidized to form Cu{sub 2}O. The presence of Cu{sub 2}O at the interface enhanced interfacial bonding strength and reduced the interfacial thermal resistance, thus improving the thermal conductivity and mechanical properties. This enhancement occurred at low rGO contents. By contrast, excessive amounts led to rGO agglomeration and a degradation of the performance. At the optimum rGO content of 0.6 wt.%, the composites had a 10% increase in thermal conductivity and a 46% increase in yield strength (σ{sub 0.2}), while maintaining high electrical conductivity.

36 MATERIALS SCIENCE↗

Corrosion Protection of Cu Electrical Cable by W-Ni Composite Coatings Doped with TiO{sub 2} Nanoparticles: Influence of Pulse Currents

W-Ni-TiO{sub 2} nano-composite layers were electrodeposited on copper surface by both direct (DC) and pulse (PC) currents. The copper substrates are samples from the main electrical cable used for the Renault K-Z (the latest 100% electric vehicle). In order to investigate coating morphology, atomic force microscopy was used, while energy-dispersive x-ray analysis was applied to determine nano-composite composition. Based on surface morphology, the W-Ni-TiO{sub 2} (DC) alloy surface was covered by massive agglomerates, especially when the W-Ni-TiO{sub 2} (PC) nano-composite coating was more compact, thicker and exhibited smaller grain size. The coated surface revealed different contents such as 43.4 and 65.4% of W in DC and PC coatings, respectively, which are considered to be a novel composition of the W-Ni alloy. XRD studies revealed that the NiW{sub 2} phase only occurs in the W-Ni-TiO{sub 2} (PC) nano-composite alloy. Electrical and thermal conductivities, microhardness and porosity values are enhanced by the addition of TiO{sub 2} to the alloy.

36 MATERIALS SCIENCE↗

Advanced Real-Time Optical Imaging: Part I

Materials research is significantly assisted by information gathered from imaging. Images may be macroscopic or microscopic; different imaging techniques ranging from conventional microscopes to synchrotron tomography are selected for various research purposes and goals. While most materials imaging is performed in static environments at room temperature because of its appropriateness (or due to device limitations), simple optical imaging may transform into a powerful tool if it is dynamically captured during materials treatments, processing, or physical/chemical exposures. Real-time observations this way provide researchers with vital information on materials behaviors under controlled but various conditions. In the field of energy materials, it is not uncommon to require materials studies under high-temperature, high-pressure, and/or corrosive conditions. In gasifiers, for example, investigations of sensor alloy degradation, slag-refractory reactions, and coal agglomeration require samples to undergo severe environments where direct imaging would be difficult using conventional experimental methods. Finally, while post mortem analysis often provides critical information, interpretation may sometimes be complicated without confirming such occurrences under those conditions.

36 MATERIALS SCIENCE↗

Metal Powder Recyclability in Binder Jet Additive Manufacturing

The recyclability of 316L stainless steel powder in the binder jetting process has been determined. The powder characterization results demonstrated a 22% increase in the number of coarse particles (> 30 µm) and an 18.2% reduction in the number of small particles (< 10 µm) after recycling up to 16 times. A few elongated and irregular-shaped particles were found after recycling, possibly due to particle agglomeration during handling and sieving. Here, a negligible increase in the oxygen content by 0.036% was detected in the recycled powder. The density of sintered parts produced using recycled powder was approximately 1.5% lower than when using fresh powder due to the changes in the particle size distribution and the flowability of the powder caused by the changes in morphology. Final parts built using fresh and recycled powder showed similar hardness (155 ± 3 HV and 165 ± 9 HV) and yield strength (206 ± 16 MPa and 192 ± 10 MPa), respectively.

36 MATERIALS SCIENCE↗

Heterogeneous 3D Morphological Evolution of Ni Microparticles in Molten Salts: Visualized by Operando Synchrotron X-ray Nano-tomography

Ni-based superalloys are promising materials for high-temperature molten salt (MS) energy generation and storage. Studying morphological and chemical evolution of pure Ni in MS provides fundamental knowledge for MS technologies and corrosion mitigation. Here, in this study, real-time 3D morphological changes of Ni microparticles in molten KCl-MgCl 2 were studied by operando synchrotron X-ray nano-tomography at 700°C. Rapid Ni particle agglomeration occurred, without significant chemical reactions, such as oxide or chloride formation. The morphological growth evolved differently from classical coarsening or sintering behaviors and occurred nonuniformly, with other regions showing slight dissolution of Ni. Ni nanoparticles were found to be dispersed in many areas of the samples, either from microparticle dissolution or other radiation-induced nanoparticle formation mechanisms. This study discusses important factors, i.e., thermal gradient, amounts of salt and metals, and radiation effect, that influence morphological changes of materials in MS, critical for fundamental understanding of material–MS interactions as well as for practical applications.

36 MATERIALS SCIENCE↗

Immobilization of Recombinant Human Catalase on Gold and Silver Nanoparticles

Human catalase cDNA was cloned into a pEX-C-His vector. Purified recombinant catalase was immobilized on nanoparticles. Gold and silver nanoparticles were synthesized in a variety of sizes by chemical reduction; no agglomerates or aggregates were observed in any of the colloids during dynamic light scattering or scanning transmission electron microscopy analysis. After immobilization on gold nanoparticles, recombinant catalase activity was found to be lower than that of the same amount of enzyme in aqueous solution. However, after 10 days of storage at room temperature, the activity of catalase immobilized on gold nanoparticles (AuNPs) of 13 and 20 nm and coverage of 133% was 68 and 83% greater than catalase in aqueous solution, respectively. During 10 days of experiment, percentage activity of catalase immobilized on those gold nanoparticles was higher in comparison to CAT in aqueous solution. Catalase immobilized on silver nanoparticles did not lose activity as significantly as catalase immobilized on AuNPs. Those results confirm the ability to produce recombinant human enzymes in a bacterial expression system and its potential use while immobilized on silver or gold nanoparticles.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A Study of the Activity of Recombinant Mn-Superoxide Dismutase in the Presence of Gold and Silver Nanoparticles

Superoxide dismutase (SOD) is one of the best characterized enzyme maintaining the redox state in the cell. A bacterial expression system was used to produce human recombinant manganese SOD with a His-tag on the C-end of the protein for better purification. In addition, gold and silver nanoparticles were chemically synthesized in a variety of sizes, and then mixed with the enzyme for immobilization. Analysis by dynamic light scattering and scanning transmission electron microscopy revealed no aggregates or agglomerates of the obtained colloids. After immobilization of the protein on AuNPs and AgNPs, the conjugates were analyzed by SDS-PAGE. It was determined that SOD was adsorbed only on the gold nanoparticles. Enzyme activity was analyzed in colloids of the gold and silver nanoparticles bearing SOD. The presence of a nanoparticle did not affect enzyme activity; however, the amount of protein and size of the gold nanoparticle did influence the enzymatic activity of the conjugate. Our findings confirm that active recombinant human superoxide dismutase can be produced using a bacterial expression system, and that the enzyme can be immobilized on metal nanoparticles. The interaction between enzymes and metal nanoparticles requires further investigation.

60 APPLIED LIFE SCIENCES↗