Multimodal Spectroscopic Study of Surface Termination Evolution in Cr 2 TiC 2 T x MXene
Explore the source record for details and available documents.
99 GENERAL AND MISCELLANEOUS↗
SEARCH · Engineering Papers
Results for “surface engineering”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analysis of backwash settings to maximize net water production in an engineering-scale ultrafiltration system for water reuse
Ultrafiltration (UF) has been widely utilized as water pretreatment for different applications especially in water reuse. The UF system operation is characterized by a filtration phase, where particles accumulate on the membrane surface resulting in an increase in the transmembrane pressure (TMP) and a cleaning phase, where foulants are removed through cleaning cycles including physical backwash and chemical-enhanced backwash (CEB). In this study, data from an engineering-scale UF system treating reclaimed wastewater were used to assess the impact of backwashing on the filtration process. TMP backwash trigger, backwash duration, and CEB frequency were purposely varied for a cycle-by-cycle investigation on the net water production, water recovery, initial operating TMP, and filtration cycle duration. As the TMP backwash trigger was varied between 62 and 145kPa, the maximum net water production (63 m 3 /d) was achieved at 103kPa and water recovery remained relatively constant at approximately 92%. Backwash durations of 45, 65, and 85s were performed where both net water production and water recovery yielded similar results (~63 m 3 /d and ~ 91%) compared with 103kPa TMP backwash trigger. The CEB frequency was also lowered from one every three backwashes (1/3) to 1/6 and 1/12 and resulted in decreased net water production and water recovery while the initial TMP increased. Interestingly, the total number of CEBs remained approximately constant regardless of their frequency. In conclusion, results suggest that CEB is an important fouling control process to maximize water production.
42 ENGINEERING↗
Open and Close-Packed, Shape-Engineered Polygonal Nanoparticle Metamolecules with Tailorable Fano Resonances
In this study, a top-down lithographic patterning and deposition process is reported for producing nanoparticles (NPs) with well-defined sizes, shapes, and compositions that are often not accessible by wet-chemical synthetic methods. These NPs are ligated and harvested from the substrate surface to prepare colloidal NP dispersions. Using a template-assisted assembly technique, fabricated NPs are driven by capillary forces to assemble into size- and shape-engineered templates and organize into open or close-packed multi-NP structures or NP metamolecules. The sizes and shapes of the NPs and of the templates control the NP number, coordination, interparticle gap size, disorder, and location of defects such as voids in the NP metamolecules. The plasmonic resonances of polygonal-shaped Au NPs are exploited to correlate the structure and optical properties of assembled NP metamolecules. Comparing open and close-packed architectures highlights that introduction of a center NP to form close-packed assemblies supports collective interactions, altering magnetic optical modes and multipolar interactions in Fano resonances. Decreasing the distance between NPs strengthens the plasmonic coupling, and the structural symmetries of the NP metamolecules determine the orientation-dependent scattering response.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Stimulated geologic hydrogen: from mechanistic control to engineered rock transformation
Geologic hydrogen (GeoH 2 ) generated from subsurface iron-rich rock–water reaction (i.e., serpentinization) is emerging as a promising candidate for the next primary energy source. Yet, accelerating GeoH 2 production from geological to human timescales via enhanced serpentinization remains a formidable scientific and technical challenge. Here, in this Review, we decipher the mechanistic control and explore strategies for accelerating in situ, engineered iron-rich rock transformation into carbon-free GeoH 2 by orders of magnitude. Serpentinization rate is hindered by low porosity and permeability of source rocks, suboptimal temperatures, unfavorable water chemistry, inefficient Fe 2+ -to-Fe 3+ conversion, thermodynamic constraints, and low reactive surface area. While closed-system experiments provide valuable mechanistic insights, open-system conditions with fluid circulation are more crucial for economically viable GeoH 2 production. We assess stimulation techniques from enhanced hydrocarbon and geothermal recovery as tools to be adopted or adapted for increasing reactive surface areas for stimulated GeoH2 production. We estimate that 7.40 × 10 5 to 1.73 × 10 6 million metric tons (Mt) of hydrogen could be engineered over 20 to 50 years from about 10% iron-rich rocks within 10 km depth of continental crust. Enabling GeoH 2 as a viable energy source requires not only advancing scientific frontiers but also forming a global GeoH 2 research network and innovation ecosystem to address the critical scientific, technical, societal, economic, and policy challenges.
08 HYDROGEN↗
Effect of Surface Roughness on Dynamic Stall in Pitching Motion
Dynamic stall plays a critical role in determining the performance and stability of a wide range of fluid-dynamics systems in various engineering applications. This unsteady aerodynamic phenomenon is particularly significant for maneuvering aircraft wings, jet aircraft subjected to gust encounters, helicopter rotor blades, and wind turbine blades [1–3]. The prediction of the dynamic stall vortex (DSV) is challenging due to factors such as unsteady aerodynamics, three-dimensional (3-D) effects, turbulence and flow separation, incoming gust, and surface impact effects [4–6]. Hence, advanced computational techniques and modeling approaches in computational fluid dynamics (CFD) would be required to enhance the accuracy and reliability of DSV predictions in dynamic stall scenarios. In the past, Batther and Lee [7] employed delayed detached eddy simulations (DDES) to understand the flow physics associated with the onset of dynamic stall. Their approach demonstrated that DDES achieves results comparable to those obtained from large-eddy simulations at a reduced computational cost. In another study, Khalifa et al. [8] examined the 3-D aspects of dynamic stall on a NACA 0012 airfoil using DES solvers. In conclusion, the findings underlined the superiority of 3-D simulations over two-dimensional approaches, particularly in predicting the lift coefficient values and capturing dynamic stall stages more precisely.
97 MATHEMATICS AND COMPUTING↗
Analysis of tow architecture variability in biaxially braided composite tubes
Spatial deviations in composite braid unit cell dimensions limit mechanical performance and are challenging to model. Full-field measurements of the irregular tow placement in biaxially braided composite tubes were obtained by digital image correlation. Analysis of the reconstructed tow paths showed long-range defects along the hoop direction with short-range defects dominating the biased tow direction. A route toward numerical simulation of the composite response is established by developing a 3D model of the composite using the measured tow trajectories. Finally, a comparison to previously-published triaxial braid results indicates axial tows work to constrain unit cells dimensions along the hoop direction.
3-Dimensional reinforcement↗
Biologically inspired reinforcement using polydopamine of polymer bound composites
Interfacial strength plays a critical role in the mechanical properties of a composite system. In this work, a proven mock high explosive (HE), 5-iodo-2’-deoxyuridine (IDOX) was coated by the adhesive promoting polymer polydopamine (PDA), then formulated with an Estane binder system to form an improved HE mock composite. An extensive comparison study of mechanical properties was performed to determine the effects, if any, of PDA on the composite system. To aid in interpretation of the mechanical test data, neutron reflectometry experiments were performed to determine the thickness and structure of the as deposited PDA films. The mechanical performance of PDA-treated IDOX was then compared to untreated specimens by compression testing in the Brazilian disk geometry. The results strongly suggested that the structure of PDA consists of two layers: one low in density caused by polymer agglomerates attaching to the substrate during polymerization, and the second high in density caused by controlled linear deposition of polydopamine. Finally, the mechanical testing showed that PDA greatly increased the stiffness and yield strength of IDOX based mocks without causing any disruption to the underlying crystal system.
42 ENGINEERING↗
Towards standardized nuclear reactors: Seismic isolation and the cost impact of the earthquake load case
We report nuclear energy has a key role to play in global decarbonization. Impediments to the widespread deployment of reactors are their projected high capital cost and levelized cost of energy, and time required to analyze, design, license, construct, and commission them. The earthquake load case is a key cost driver for a new build nuclear plant, because near-surface soils and seismic hazard are different at each site, requiring site-specific analysis, design, engineering, qualification, licensing, and regulatory review, essentially making every design First-of-a-Kind (FoaK). To enable deployment at the scale needed for deep decarbonization, the cost and time impact of the seismic load case must be significantly mitigated, and plants must be standardized. Seismic base isolation has been proven to considerably reduce the earthquake response of structures and equipment but has yet to be applied to a nuclear power plant in the United States, in part because the financial impacts, positive or negative, are not known. Because there are no recent non-proprietary data to characterize the influence of the seismic load case on capital cost, it is difficult to confidently quantify the financial benefits of seismic isolation. Scheme-level designs of two fundamentally different advanced reactor buildings were developed to assemble cost data on the influence of the seismic load case. Both buildings were equipped with three bespoke pieces of safety-related equipment and analyzed for incremented levels of earthquake shaking to quantify the seismic penalty on equipment, in terms of vessel weights and horizontal accelerations. Using analysis results, a questionnaire was developed and transmitted to nuclear utilities, reactor developers, engineers, and equipment suppliers to collect cost data on engineering and fabrication costs for these unique pieces of safety-class equipment. Synthesis of the cost data showed that the seismic load case significantly affects the capital cost (sum of engineering and fabrication cost) of safety-class equipment, with engineering costs being comparable to fabrication costs. Standardization of safety-class equipment is made possible by seismic isolation, that is, equipment designed for minimal seismic robustness can resist earthquake shaking at a site of much higher seismic hazard. The average reduction in the capital cost of the safety-related equipment, enabled by seismic isolation, is a factor of two for FoaK equipment and a factor of five for standardized equipment.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Engineering new limits to magnetostriction through metastability in iron-gallium alloys
Magnetostrictive materials transduce magnetic and mechanical energies and when combined with piezoelectric elements, evoke magnetoelectric transduction for high-sensitivity magnetic field sensors and energy-efficient beyond-CMOS technologies. The dearth of ductile, rare-earth-free materials with high magnetostrictive coefficients motivates the discovery of superior materials. Fe 1- x Ga x alloys are amongst the highest performing rare-earth-free magnetostrictive materials; however, magnetostriction becomes sharply suppressed beyond x = 19% due to the formation of a parasitic ordered intermetallic phase. Here, we harness epitaxy to extend the stability of the BCC Fe 1- x Ga x alloy to gallium compositions as high as x = 30% and in so doing dramatically boost the magnetostriction by as much as 10x relative to the bulk and 2x larger than canonical rare-earth based magnetostrictors. A Fe 1- x Ga x - [Pb(Mg 1/3 Nb 2/3 )O 3 ] 0.7 -[PbTiO 3 ] 0.3 (PMN-PT) composite magnetoelectric shows robust 90° electrical switching of magnetic anisotropy and a converse magnetoelectric coefficient of 2.0 × 10 -5 s m -1 . When optimally scaled, this high coefficient implies stable switching at ~80 aJ per bit.
36 MATERIALS SCIENCE↗
Direct Numerical Simulation of Transitional and Turbulent Flows Over Multi-Scale Surface Roughness—Part I: Methodology and Challenges
Abstract High-fidelity simulation of transitional and turbulent flows over multi-scale surface roughness presents several challenges. For instance, the complex and irregular geometrical nature of surface roughness makes it impractical to employ conforming structured grids, commonly adopted in large-scale numerical simulations due to their high computational efficiency. One possible solution to overcome this problem is offered by immersed boundary methods, which allow wall boundary conditions to be enforced on grids that do not conform to the geometry of the solid boundary. To this end, a three-dimensional, second-order accurate boundary data immersion method (BDIM) is adopted. A novel mapping algorithm that can be applied to general three-dimensional surfaces is presented, together with a newly developed data-capturing methodology to extract and analyze on-surface flow quantities of interest. A rigorous procedure to compute gradient quantities such as the wall shear stress and the heat flux on complex non-conforming geometries is also introduced. The new framework is validated by performing a direct numerical simulation (DNS) of fully developed turbulent channel flow over sinusoidal egg-carton roughness in a minimal-span domain. For this canonical case, the averaged streamwise velocity profiles are compared against results from the literature obtained with a body-fitted grid. General guidelines on the BDIM resolution requirements for multi-scale roughness simulation are given. Momentum and energy balance methods are used to validate the calculation of the overall skin friction and heat transfer at the wall. The BDIM is then employed to investigate the effect of irregular homogeneous surface roughness on the performance of an LS-89 high-pressure turbine blade at engine-relevant conditions using DNS. This is the first application of the BDIM to realize multi-scale roughness for transitional flow in transonic conditions in the context of high-pressure turbines. The methodology adopted to generate the desired roughness distribution and to apply it to the reference blade geometry is introduced. The results are compared to the case of an equivalent smooth blade.
Engineering↗
Aviation Fuel Characterization at Operationally Relevant Conditions
To accelerate approval and potentially expand the allowable property range for aviation fuels, we are using high performance computing simulations to reveal fuel property effects on aviation combustor performance. These simulations are supported by fuel property measurements over temperatures and pressures that the fuel experiences in an aircraft engine and by validated chemical kinetics models for SAF combustion. Here we report density, viscosity, and surface tension results for conventional jet fuel and multiple synthetic fuels from -30 degrees Celsius to 200 degrees Celsius (-40 degrees Celsius for viscosity) and 1 atm to 70 atm including an assessment of method repeatability. Properties of surrogate mixtures are also investigated. Distillation, ICN, LHV, flashpoint, and Cp are also reported, and data are being used to develop models to predict fuel properties from composition (GCxGC).
33 ADVANCED PROPULSION SYSTEMS↗
Study of a linear surface wave plasma source for tin removal in an extreme ultraviolet source
Tin deposition mitigation employs hydrogen radicals and ions, formed in a hydrogen plasma, to interact with tin to form tin hydride (SnH 4 ) in the gaseous state, which is then pumped away. Surface wave plasma (SWP) technology developed at Illinois generates hydrogen radicals and ions, resulting in tin etch rates that are high enough to keep extreme ultraviolet (EUV) lithographic tools clean. An advantage of an SWP antenna is the ability to generate a high density of hydrogen radicals and hydrogen ions directly at the desired etching location. In situ etching of tin enables high availability EUV tools by maintaining high reflectivity of the multilayer mirror of the collector. Additionally, the SWP is characterized with low ion energies and low electron temperature, such that the multilayer mirror does not suffer any damage from sputtering or implantation of hydrogen ions during operation. Here, experiments elucidating the fundamental processes of tin removal are conducted by varying pressure, power, surface temperature, and gas flow rate in order to observe the etch rate behavior. Our results have shown that the presence of hydrogen ions increases etch rates because ion bombardment weakens Sn–Sn bonds, which, in turn, allows for a higher rate of chemical etching by the radicals. The ion bombardment reduces the number of radicals needed to etch a single tin atom to the range of 10 2 –10 3 . The linear SWP antenna yields plasma densities on the order of 10 17 to 10 18 m -3 and radical densities on the order of 10 18 to 10 19 m -3 , allowing for greater utilization of ion etch enhancement. Etch rates of up to 200 nm/min have been achieved. The surface temperature of the samples is an important factor in the etching process such that the decrease in the surface temperature increases the etch rates and decreases the hydrogen desorption rates. In addition, a kinetic etch model is developed to explain the behavior of etch rates as a function of surface temperature. Furthermore, results from experiments performed in an Illinois NXE:3100 chamber will be discussed.
42 ENGINEERING↗
Enhanced Tritium Retention in LiAlO2 Pellets via Engineered Glazes: Tritium Science Project
This project investigated the impact of adding a thin (10 – 50 µm) layer of amorphous glaze to the surface of a TPBAR pellet on its retention of helium, hydrogen (as a surrogate for tritium), and water (as a surrogate for tritiated water). The hypothesis was that the glaze would significantly reduce permeation of hydrogen species with a lesser impact on hindering helium permeation. A non-crystallizing soda-lime-silicate glass, known as SCN-1, was selected for this proof-of-concept study. It was found that continuous glaze layers of the desired thickness could be applied to the pellets with two or more dip coats, depending on the targeted thickness. At 330°C, the glaze was found to have a permeability that was lower than that of the pellet by a factor of ~10 6 , implying that a thin 10 – 50 µm layer can significantly increase pellet retention of hydrogen. Meanwhile, the permeation rate of helium through the glaze was found to be ~20 times higher than that of hydrogen or water. An unanticipated outcome of the study was that unglazed pellets were measured to have hydrogen diffusivities that are a factor of ~105 greater than the diffusivity value used in the TPBAR COMSOL model to achieve observed tritium retention rates. When the higher measured diffusivity was substituted into the model and the model was run with all tritium species in the pellet in the form of T 2 O at a partial pressure of 20 Pa in equilibrium with LiOT, the resulting retention was 50% after 500 days.
36 MATERIALS SCIENCE↗
The simulation of 3D hypervelocity spallation using a hydrocode PAGOSA with FLIP+MPM
n this work, a hydrocode PAGOSA with FLIP+MPM is presented and exercised to investigate the fracture in ductile material. The merit of PAGOSA with FLIP+MPM to solve the advection problem is first illustrated by a solid piston periodically moving in a sealed tube with air. Furthermore, the ability of PAGOSA with FLIP+MPM to capture the fracture in material is shown by a simple stretching fracture in ductile material. In both of two benchmark problems, the PAGOSA results and analytical solutions are also presented for comparison. Then PAGOSA with FLIP+MPM is used to model complex spall in ductile material, which is a challenging problem in engineering applications. The convergences of PAGOSA with FLIP+MPM—based on both the mesh size and the marker density—are investigated by monitoring free surface velocity. To further show the ability of PAGOSA with FLIP+MPM to predict fracture in ductile material, the numerical results are compared with the experimental results and other published numerical results. Moreover, the effect of the spall parameter in PAGOSA with FLIP+MPM on the numerical simulation is also analyzed by investigating the free surface velocity. Finally, the effects of the peak compressive stress, the tensile strain rate, and the loading rate on the spallation are further investigated. The numerical results show that PAGOSA with FLIP+MPM can improve PAGOSA's performance when applied to predicting fracture in ductile materials, and is robust enough to accurately predict spall fracture in ductile materials.
42 ENGINEERING↗
Dynamic Metal–Support Interaction Dictates Cu Nanoparticle Sintering on Al 2 O 3 Surfaces
Nanoparticle sintering remains a critical challenge in heterogeneous catalysis. In this work, we present a unified deep potential (DP) model based on the Perdew–Burke–Ernzerhof approximation of density functional theory for Cu nanoparticles on three Al 2 O 3 surfaces (γ-Al 2 O 3 (100), γ-Al 2 O 3 (110), and α-Al 2 O 3 (0001)). Using DP-accelerated simulations, we reveal that the nanoparticle size-mobility relationship strongly depends on the supporting surface. The diffusion of nanoparticles on the two γ-Al 2 O 3 surfaces is almost independent of the size of the nanoparticle, while the diffusion on α-Al 2 O 3 (0001) decreases rapidly with increasing size. Interestingly, nanoparticles with fewer than 55 atoms diffuse several times faster on α-Al 2 O 3 (0001) than on γ-Al 2 O 3 (100) at 800 K while expected to be more sluggish based on their larger binding energy at 0 K. The diffusion on α-Al 2 O 3 (0001) is facilitated by dynamic metal–support interaction (MSI), where Al atoms move out of the surface plane to optimize contact with the nanoparticle and relax back to the plane as the nanoparticle moves away. In contrast, the MSI on γ-Al 2 O 3 (100) and on γ-Al 2 O 3 (110) is dominated by more stable and directional Cu–O bonds, consistent with the limited diffusion observed on these surfaces. Our extended MD simulations provide insight into the sintering processes, showing that the dispersity of the nanoparticles strongly influences the coalescence driven by nanoparticle diffusion. We observed that the coalescence of Cu 13 nanoparticles on α-Al 2 O 3 (0001) can occur in a short time (10 ns) at 800 K even with an initial internanoparticle distance increased to 3 nm, while the coalescence on the two γ-Al 2 O 3 surfaces are inhibited significantly by increasing the initial internanoparticle distance. These findings demonstrate that the dynamics of the supporting surface is crucial to understanding the sintering mechanism and offer guidance for designing sinter-resistant catalysts by engineering the support morphology.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Optimization of spray breakup model parameters for predicting fuel spray and film characteristics in gasoline direct injection engines
This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. Here, with the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.
Computational fluid dynamics (CFD)↗
Chemistry and Interfacial Structure Promoting Quasi-van der Waals Epitaxial Growth of WS 2 Nanosheets on Sapphire for Prospective Application in Field-Effect Transistors
How do chemical and structural modifications to the supporting crystal surface affect the subsequent van der Waals (vdW) or quasi(Q)-vdW epitaxial growth of 2D nanocrystals? Developing an atomic-scale picture of such an interfacial system is crucial for understanding its impact on the physical and chemical properties of the supported 2D materials. The elucidation of the interfacial structure and chemistry needed to promote the Q-vdW epitaxial growth of 2D tungsten disulfide (WS 2 ) nanocrystals contributes to the growth mechanism understanding, thus pushing forward the integration of such atomically thin semiconductors toward real field-effect transistor applications. In addition to an atomic-force microscopy top view, we showcase a combination of X-ray techniques for a top-to-bottom investigation of the complexities of the buried interface structures. Furthermore, this approach uses X-ray photoelectron spectroscopy, X-ray standing wave excited X-ray fluorescence, and crystal truncation rod scattering to produce a highly resolved chemical-state-specific 3D atomic map for the extended interface structure of WS 2 /α-Al 2 O 3 (001). Employing these detailed analysis methods, along with density functional theory to further refine the picoscale structure, we demonstrate how two different types of interface engineering during the pregrowth stage lead to significant differences in the chemical and structural modifications to the terminal surface of c-face sapphire, which in turn leads to substantial differences in the submonolayer growth of supported WS 2 2D nanocrystals in terms of lateral domain sizes, epitaxial registry, vdW gaps, and stability.
36 MATERIALS SCIENCE↗