Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sublimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Fluid Dynamics and Thermodynamics of Vapor Phase Crystal Growth

The ground-based research effort under this program is concerned with systematic studies of the effects of variations: (1) of the relative importance of buoyancy-driven convection, and (2) of diffusion and viscosity conditions on crystal properties. These experimental studies are supported by thermodynamic characterizations of the systems, based on which fluid dynamic parameters can be determined. The specific materials under investigation include: the GeSe-GeI4, Ge-GeI4, HgTe-HgI2, and Hg sub (1-x)Cd sub (x) Te-HgI2 systems. Mass transport rate studies of the GeSe-GeI system as a function of orientation of the density gradient relative to the gravity vector demonstrated the validity of flux anomalies observed in earlier space experiments. The investigation of the effects of inert gases on mass flux yielded the first experimental evidence for the existence of a boundary layer in closed ampoules. Combined with a thorough thermodynamic analysis, a transport model for diffusive flow including chemical vapor transport, sublimation, and Stefan flow was developed.

Wiedemeier, H.↗

Hydride absorption refrigerator system for ten Kelvin and below

A very long-life, lightweight and efficient hydride absorption refrigerator system was built to operate at ten Kelvin and below. The system consists of four basic stages of refrigeration. The first stage is accomplished by an active refrigeration system. The second stage is operated by a hydride absorption system, wherein a heated hydride powder drives off high pressure hydrogen through a Joule-Thomson/heat exchanger expansion loop such that the hydrogen is partially liquefied. In the third stage, the vapor pressure over the collected liquid hydrogen is lowered by absorbing the hydrogen vapor onto a different low pressure, worn hydride. With a 1.7 torr partial pressure of hydrogen gas in the hydride, liquid hydrogen is solidified and sublimes at 10 K. Long-life adiabatic demagnetization refrigerators, helium desorption, or helium diaphragm compressors are used to cool to 4 K or below. It is shown that the hydride concepts provide an extremely efficient means of refrigeration to 10 K, and that an entire sorption refrigeration process can be accomplished solely by using low grade heat energy at about 150 C.

Jones, J. A.↗

Workshop on Water on Mars

The opening session of the Workshop focused on one of the most debated areas of Mars volatiles research-the size of the planet's past and present bulk water content. Current estimates of the inventory of H2O on Mars range from an equivalent layer of liquid 10-1000 meters deep averaged over the planet's surface. The most recent of these estimates, presented at the Workshop, is based on the now popular belief that the SNC class of meteorites represent actual samples of the Martian crust. From a model of planetary accretion and degassing founded on this assumption, it was determined that the present inventory of H2O on Mars is equivalent to a global layer no more than 50 meters deep. During the discussion generated by this estimate, several investigators expressed reservations about an H2O inventory as small as a few tens of meters, for it appears to directly contradict the seemingly abundant morphologic evidence that Mars is (or has been) water rich. Others, however, argued that the interpretation of much of this morphologic evidence is at best equivocal and that the case for a wet Mars is far from established. Atmospheric water vapor measurements, compiled by Earth based telescopes and the Viking Orbiter Mars Atmospheric Water Detectors (MAWD), now span a period of over six Martian years. Analysis of this data suggests that the seasonal cycle is governed by both the sublimation and condensation of H2O at the poles and by its adsorption/desorption within the regolith. So far, efforts to simulate the seasonal vapor cycle have failed to reproduce the observed behavior.

Clifford, S.↗

Determination of convective diffusion heat/mass transfer rates to burner rig test targets comparable in size to cross-stream jet diameter

Two sets of experiments have been performed to be able to predict the convective diffusion heat/mass transfer rates to a cylindrical target whose height and diameter are comparable to, but less than, the diameter of the circular cross-stream jet, thereby simulating the same geometric configuration as a typical burner rig test specimen located in the cross-stream of the combustor exit nozzle. The first set exploits the naphthalene sublimation technique to determine the heat/mass transfer coefficient under isothermal conditions for various flow rates (Reynolds numbers). The second set, conducted at various combustion temperatures and Reynolds numbers, utilized the temperature variation along the surface of the above-mentioned target under steady-state conditions to estimate the effect of cooling (dilution) due to the entrainment of stagnant room temperature air. The experimental information obtained is used to predict high temperature, high velocity corrosive salt vapor deposition rates in burner rigs on collectors that are geometrically the same. The agreement with preliminary data obtained from Na2SO4 vapor deposition experiments is found to be excellent.

Gokoglu, S. A.↗

Experiments for the determination of convective diffusion heat/mass transfer to burner rig test targets comparable in size to jet stream diameter

The application of a recently formulated vapor transport theory to predict deposition rates of corrosive salts from alkali-seeded combustion gases of a small-capacity, high-velocity, atmospheric-pressure burner rig was hampered by the relatively large dimensions of the cylindrical deposit collector compared to the diameter of the combustion gas stream. The relative dimensions lead to a highly nonadiabatic combustion gas flow around the collector and necessitate two series of experiments. In the first series, mass transfer coefficients are determined by utilizing the naphthalene sublimation technique. The second series of experiments determines the dilution effect on the sodium species concentrations due to the entrainment of ambient air. This second series involves the measurement of the temperature variation along the surface of the collector under steady state conditions. Vapor deposition rates are determined exploiting this information and the results are found to compare favorably with experimentally obtained rates.

Santoro, G. J.↗

Theoretical and experimental investigation of the destruction of graphites in a flow of dissociated air

A method is presented for calculating the heating and erosion of blunt bodies made of graphite in a high-enthalpy flow of dissociated air, assuming chemical equilibrium on the surface and taking account of the thermal effects of combustion and sublimation of graphite. The analysis involves the use of a finite difference scheme to solve an equation of unsteady heat conduction. Attention is given to the equilibrium vaporization of C, C2 and C3 molecules. The calculations agree well with experimental data for a wide range of temperatures and stagnation pressures.

Bovina, T. A.↗

How to make a comet

The primary mandate of NASA is the study of the nature and origin of the solar system. The study of comets provides information about conditions and processes at the beginning of the solar system. Short period comets and their relatives, the near Earth asteroids may prove to be second only to the Sun in importance to the long term survival of civilization for two reasons: as a possible candidate for the cause of mass extinctions of life on Earth and as the material means for the expansion of civilization into the solar system and beyond. In the mean time comets are studied by remote means. Laboratory investigations using synthetic cometary materials may add to the knowledge of these interesting objects. Dust and mantle formation are currently being studied by the use of comet sublimation experiments. Results of these experiments are discussed.

Stephens, J.↗

Process for preparing essentially colorless polyimide film containing phenoxy-linked diamines

A polyimide film that is approximately 90% transparent at 500 nm, useful for thermal protective coatings and solar cells, and the processes for preparing the same by thermal and chemical conversion are disclosed. An essential feature for achieving maximum optical transparency films requires utilizing recrystallized and/or sublimated specific aromatic diamines and dianhydride monomers and introducing phenoxy or thiophenyl separator groups and isomeric m,m' or o,p'-oriented diamines into the polymer molecular structure. The incorporation of these groups in the polymer structure serves to separate the chromaphoric centers and reduce the formation of inter-chain and intra-chain charge transfer complexes which normally cause absorptions in the UV-visible range. The films may be obtained by hand, brushing, casting, or spraying a layer of polyamic acid solutions onto a surface and thermally converting the applied layer to the polyimide, or the polyamic acid solution can be chemically converted to the polyimide, subsequentially dissolved in an organic solvent, and applied as a polyimide film layer with the solvent therein thermally removed.

Stclair, A. K.↗

Comparison of predicted and measured drag for a single-engine airplane

Renewed interest in natural laminar flow (NLF) has rekindled designers' concerns that manufacturing deviations, (loss of surface contours or other surface imperfections) may destroy the effectiveness of NLF for an operational airplane. This paper reports on experimental research that compares predicted and measured boundary layer transition, total drag, and two-dimensional drag coefficients for three different wing surface conditions on an airplane typical of general aviation manufacturing technology. The three flight test phases included: (1) assessment of an unpainted airframe, (2) flight tests of the same airplane after painstakingly filling and sanding the wings to design contours, and (3) similar measurements after this airplane was painted. In each flight phase, transition locations were monitored using either sublimating chemicals or pigmented oil. As expected, total drag changes were difficult to measure. Two-dimensional drag coefficients were estimated using the Eppler-Somers code and measured with a wake rake in a method very similar to Jones' pitot traverse method. The net change in two-dimensional drag was approximately 20 counts between the unpainted airplane and the 'hand-smoothed' airplane for typical cruise flight conditions.

Ward, D. T.↗

Geomorphic evidence for the distribution of ground ice on Mars

High-resolution Viking orbiter images show evidenced for quasi-viscous relaxation of topography. The relaxation is believed to be due to creep deformation of ice in near-surface materials. The global distribution of the inferred ground ice shows a pronounced latitudinal dependence. The equatorial regions of Mars appear to be ice-poor, while the heavily cratered terrain poleward of + or - 30 deg latitude appears to be ice-rich. The style of creep poleward of + or - 30 deg varies with latitude, possibly due to variations in ice rheology with temperature. The distribution suggests that ice at low latitudes, which is not in equilibrium with the present atmosphere, has been lost via sublimation and diffusion through the regolith, thereby causing a net poleward transport of ice over martian history.

Squyres, S. W.↗

The Martian hydrologic cycle - Effects of CO2 mass flux on global water distribution

The Martian CO2 cycle, which includes the seasonal condensation and subsequent sublimation of up to 30 percent of the planet's atmosphere, produces meridional winds due to the consequent mass flux of CO2. These winds currently display strong seasonal and hemispheric asymmetries due to the large asymmetries in the distribution of insolation on Mars. It is proposed that asymmetric meridional advection of water vapor on the planet due to these CO2 condensation winds is capable of explaining the observed dessication of Mars' south polar region at the current time. A simple model for water vapor transport is used to verify this hypothesis and to speculate on the effects of changes in orbital parameters on the seasonal water cycle.

James, P. B.↗

Effects of the law for nongravitational forces on the precession model of comet Encke

The precession model for P/Encke formulated by Whipple and Sekanina (1979) is reexamined in the light of the recent measurements of the OH and H production rates. An optimized precession solution derived using the production law of A'Hearn et al. (1985) is shown to require unacceptably small nucleus dimensions and to offer an inferior fit to observed variations in the orientation of the comet's perihelion fan-shaped coma. Observed changes in the emission fan suggest that both the thrust on the nucleus exerted by unit mass of sublimating ice and the average lag in outgassing are substantially greater before than after perihelion. It is concluded that at this time the Whipple-Sekanina model remains the best available precession solution for this comet.

Sekanina, Z.↗

Ion composition results during the International Cometary Explorer encounter with Giacobini-Zinner

The International Cometary Explorer spacecraft passed through the coma of comet Giacobini-Zinner about 7800 kilometers antisunward of the nucleus on September 11, 1985. The ion composition instrument was sensitive to ambient ions with mass-to-charge ratios in the ranges 1.4 to 3 atomic mass units per electron charge (amu/e) and 14 to 33 amu/e. Initial interpretation of the measurements indicates the presence of H2O(+), H3O(+), probably CO(+) and HCO(+), and ions in the mass range 23 to 24; possible candidates are Na(+) and Mg(+) and Mg(+). In addition to these heavy ions, measured over the velocity range 80 to 223 kilometers per second, the instruments measured He(2+) of solar wind origin over the range 237 to 463 kilometers per second. The heavy ions have a velocity distribution which indicates that they have been picked up by the motional electric field, whereas the light ions are steadily decelerated as the comet tail axis is approached. These results are in agreement with the picture of a comet primarily consisting of water ice, together with other material, that sublimes, streams away from the nucleus, becomes ionized, and interacts with the solar wind.

Ogilvie, K. W.↗

Disturbance functions of the Goertler instability on an airfoil

Goertler vortices arise in boundary layers along concave surfaces due to centrifugal effects. This paper presents some results of an experiment conducted to study the development of these vortices on an airfoil with a pressure gradient in the concave region where an attached laminar boundary layer was insured with suction through a perforated panel. A sublimating chemical technique was used to visualize Goertler vortices and the velocity field was measured by laser velocimetry. Experimental disturbance functions are compared with those predicted by the linear stability theory. The trend of vortex amplification in the concave zone and damping in the following convex region is shown to essentially follow the theoretical predictions.

Dagenhart, J. R.↗

Further results of natural laminar flow flight test experiments

Flight test experiments were conducted to measure the extent and nature of natural laminar flow on a smoothed test region of a swept-wing business jet wing. Surface hot film anemometry and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Engine noise was monitored by a microphone attached to the wing surface to study possible acoustic effects on stability of the laminar boundary layer. Side-slip conditions were flown to simulate changes in effective wing sweep. Flight instrumentation and ground data analysis techniques and a method for measuring intermittency of turbulence are described. Correlation was obtained between the hot film gage signals and chemicals for transition detection. Cross-flow vortices were observed for some flight conditions. Results of spectral and statistical analysis of the hot film signals for various flight test conditions are presented.

Wentz, W. H., Jr.↗

Composition and stability of the condensate observed at the Viking Lander 2 site on Mars

Surface energy balance and near-surface temperature data from the Viking Lander 2 site taken during the first winter that condensated were observed and analyzed to determine the relative stability of CO2 and H2O frosts. The CO2 frost stability is calculated with an equilibrium surface energy balance model, i.e., the total energy incident on a frost surface is compared with the blackbody energy emitted by the surface. The energy sources considered were IR emission from the atmosphere, sunlight, and the sensible heat flux from the atmosphere. H2O stability was examined as a function of buoyant diffusion and turbulent mixing processes which could remove saturated near-surface gases. The CO2 frost is found to be sufficiently unstable at the time the condensate was observed on the ground, so all CO2 ice deposited at night would boil away in a few hours of sunlight. CO2 ice would not form during a dust storm. Water frost would be stable during the condensate observations, since sublimation would occur at a rate below 1 micron/day. A stable winter thickness of 10 microns is projected for the water ice.

Hart, H. M.↗

Oxygen budget of a perennially ice-covered Antarctic lake

A bulk O2 budget for Lake Hoare, Antarctica, is presented. Five years of seasonal data show the lake to be persistently supersaturated with O2. Oxygen is carried into the lake in glacial meltstreams and is left behind when this water is removed as ice by ablation and sublimation. A diffusive loss of O2 from the lake through the summer moat is suggested. Measured values of the total O2 in the water column indicate that the time scale of O2 turnover is much longer than a year. Based on these results, it is suggested that the amount of O2 in the water does not change significantly throughout the year and that the lake is also supersaturated with N2.

Wharton, R. A., Jr.↗