Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solar eclipse”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

W134: A new pre-main-sequence double-lined spectroscopic binary

We report the discovery that the pre-main-sequence star Walker 134 in the young cluster NGC 2264 is a double-lined spectroscopic binary. Both components are G stars with strong Li I 6708 A absorption lines. Twenty radial velocity measurements have been used to determined the orbital elements of this system. The orbit has a period of 6.3532 +/- 0.0012 days and is circular within the limits of our velocity resolution; e less than 0.01. The total system mass is stellar mass sin(exp 3) i = 3.16 solar mass with a mass ratio of 1.04. Estimates for the orbit inclination angle and stellar radii place the system near the threshold for eclipse observability; howerver, no decrease in brightness was seen during two attempts at photometric monitoring. The circular orbit of W 134 fills an important gap in the period distribution of pre-main-sequence binaries and thereby constrains the effectiveness of tidal orbital circularization during the pre-main sequence.

Padgett, Deborah L.↗

Spacecraft Charging and the Microwave Anisotropy Probe Spacecraft

The Microwave Anisotropy Probe (MAP), a MIDEX mission built in partnership between Princeton University and the NASA Goddard Space Flight Center (GSFC), will study the cosmic microwave background. It will be inserted into a highly elliptical earth orbit for several weeks and then use a lunar gravity assist to orbit around the second Lagrangian point (L2), 1.5 million kilometers, anti-sunward from the earth. The charging environment for the phasing loops and at L2 was evaluated. There is a limited set of data for L2; the GEOTAIL spacecraft measured relatively low spacecraft potentials (approx. 50 V maximum) near L2. The main area of concern for charging on the MAP spacecraft is the well-established threat posed by the "geosynchronous region" between 6-10 Re. The launch in the autumn of 2000 will coincide with the falling of the solar maximum, a period when the likelihood of a substorm is higher than usual. The likelihood of a substorm at that time has been roughly estimated to be on the order of 20% for a typical MAP mission profile. Because of the possibility of spacecraft charging, a requirement for conductive spacecraft surfaces was established early in the program. Subsequent NASCAP/GEO analyses for the MAP spacecraft demonstrated that a significant portion of the sunlit surface (solar cell cover glass and sunshade) could have nonconductive surfaces without significantly raising differential charging. The need for conductive materials on surfaces continually in eclipse has also been reinforced by NASCAP analyses.

Timothy, VanSant J.↗

Radiation Heat Transfer Modeling Improved for Phase-Change, Thermal Energy Storage Systems

Spacecraft solar dynamic power systems typically use high-temperature phase-change materials to efficiently store thermal energy for heat engine operation in orbital eclipse periods. Lithium fluoride salts are particularly well suited for this application because of their high heat of fusion, long-term stability, and appropriate melting point. Considerable attention has been focused on the development of thermal energy storage (TES) canisters that employ either pure lithium fluoride (LiF), with a melting point of 1121 K, or eutectic composition lithium-fluoride/calcium-difluoride (LiF-20CaF2), with a 1040 K melting point, as the phase-change material. Primary goals of TES canister development include maximizing the phase-change material melt fraction, minimizing the canister mass per unit of energy storage, and maximizing the phase-change material thermal charge/discharge rates within the limits posed by the container structure.

Kerslake, Thomas W.↗

Absolute properties of the eclipsing binary star AP Andromedae

AP And is a well-detached F5 eclipsing binary star for which only a very limited amount of information was available before this publication. We have obtained very extensive measurements of the light curve (19,097 differential V magnitude observations) and a radial velocity curve (83 spectroscopic observations) which allow us to fit orbits and determine the absolute properties of the components very accurately: masses of 1.277 ± 0.004 and 1.251 ± 0.004 M {sub ☉}, radii of 1.233 ± 0.006 and 1.1953 ± 0.005 R {sub ☉}, and temperatures of 6565 ± 150 K and 6495 ± 150 K. The distance to the system is about 400 ± 30 pc. Comparison with the theoretical properties of the stellar evolutionary models of the Yonsei-Yale series of Yi et al. shows good agreement between the observations and the theory at an age of about 500 Myr and a slightly sub-solar metallicity.

79 ASTRONOMY AND ASTROPHYSICS↗

Design study for LANDSAT-D attitude control system

The gimballed Ku-band antenna system for communication with TDRS was studied. By means of an error analysis it was demonstrated that the antenna cannot be open loop pointed to TDRS by an onboard programmer, but that an autotrack system was required. After some tradeoffs, a two-axis, azimuth-elevation type gimbal configuration was recommended for the antenna. It is shown that gimbal lock only occurs when LANDSAT-D is over water where a temporary loss of the communication link to TDRS is of no consequence. A preliminary gimbal control system design is also presented. A digital computer program was written that computes antenna gimbal angle profiles, assesses percent antenna beam interference with the solar array, and determines whether the spacecraft is over land or water, a lighted earth or a dark earth, and whether the spacecraft is in eclipse.

Iwens, R. P.↗

The 1992/93 eclipse of 31 Cygni

Extensive new ultraviolet and optical spectra of an atmospheric eclipse define the physical properties throughout the wind and chromosphere of 31 Cyg. These data require mass loss of approximately 3 x 10(exp -8) solar masses/yr in a wind that may merge smoothly into the chromosphere. Considerations of how energy is injected into the wind, however, suggest that the chromosphere and wind are separate structures. Most, if not all, of the velocity structure in metallic lines, which we have heretofore simulated with Doppler widths in the range 15-25 km/s, results from differential expansion of the atmosphere. Electron densities in the inner R(sub star) of the chromosphere are in the range 1.5 x 10(exp 9) - 2 x 10(exp 8)/cu cm, which implies clumping of the gas. The ionization of oxygen and nitrogen is consistent with clumping by factors of 3-30 in the outer chromosphere, roughly the amount required to give enough gas pressure to support the chromosphere. Chromospheric gas in 31 Cyg becomes hotter with increasing height, thus with decreasing optical depth, in a way that seems similar for all the zeta Aur binaries. Excitation temperature for Fe II in 1992/93 rises from about 5000 K at the deepest points sampled to about 12,500 K high in the wind. Strengths of violet Balmer lines give an excitation temperature for hydrogen of 6200-6500 K above a radial mass column density of approximately 0.01 g/sq cm. This amount of excitation implies that Lyman-alpha is thermalized beneath about 4 x 10(exp -3) g/sq cm. The outer atmosphere was symmetrical to within a factor of 2 in 1992/93, although it was clearly variable at this level, and it had similar mass column densities as in 1982. One manifestation of the variability was a flow toward the B star at phases 0.013-0.022 spanning velocities 45-100 km/s. Several lines of evidence point to a complicated and variable ionization in the wind: At large distance from the K star, measured mass column densities are less by up to a factor of 3 than required by a smoothly flowing wind. Also, much of the gas beyond r = 350 solar radii = 1.75 R(sub star) has a negative radial velocity. Radial velocities of the shell lines imply the outer atmosphere rotates in the direction of orbital motion, possibly through the deflection of wind flow lines in this direction.

Eaton, Joel A.↗

Earth Observing-1 Advanced Imager Flight Performance Assessment: Investigating Dark Current Stability Over One-Half Orbit Period during the First 60 Days

The stability of the EO-1 Advanced Land Imager dark current levels over the period of one-half orbit is investigated. A series of two-second dark current collections, over the course of 40 minutes, was performed during the first sixty days the instrument was in orbit. Analysis of this data indicates only two dark current reference periods, obtained entering and exiting eclipse, are required to remove ALI dark current offsets for 99.9% of the focal plane to within 1.5 digital numbers for any observation on the solar illuminated portion of the orbit.

Mendenhall, J. A.↗

Plasma Interaction with International Space Station High Voltage Solar Arrays

The International Space Station (ISS) is presently being assembled in low-earth orbit (LEO) operating high voltage solar arrays (-160 V max, -140 V typical with respect to the ambient atmosphere). At the station's present altitude, there exists substantial ambient plasma that can interact with the solar arrays. The biasing of an object to an electric potential immersed in plasma creates a plasma "sheath" or non-equilibrium plasma around the object to mask out the electric fields. A positively biased object can collect electrons from the plasma sheath and the sheath will draw a current from the surrounding plasma. This parasitic current can enter the solar cells and effectively "short out" the potential across the cells, reducing the power that can be generated by the panels. Predictions of collected current based on previous high voltage experiments (SAMPIE (Solar Array Module Plasma Interactions Experiment), PASP+ (Photovoltaic Array Space Power) were on the order of amperes of current. However, present measurements of parasitic current are on the order of several milliamperes, and the current collection mainly occurs during an "eclipse exit" event, i.e., when the space station comes out of darkness. This collection also has a time scale, t approx. 1000 s, that is much slower than any known plasma interaction time scales. The reason for the discrepancy between predictions and present electron collection is not understood and is under investigation by the PCU (Plasma Contactor Unit) "Tiger" team. This paper will examine the potential structure within and around the solar arrays, and the possible causes and reasons for the electron collection of the array.

John W. Heard↗

Transit of Extrasolar Planets

During the past five years we have pursued the detection of extrasolar planets by the photometric transit method, i.e. the detection of a planet by watching for a drop in the brightness of the light as it crosses in front of a star. The planetary orbit must cross the line-of-sight and so most systems will not be lined up for such a transit to ever occur. However, we have looked at eclipsing binary systems which are already edge-on. Such systems must be very small in size as this makes the differential light change due to a transit much greater for a given planet size (the brightness difference will be proportional to the area of the transiting planet to the disc area of the star). Also, the planet forming region should be closer to the star as small stars are generally less luminous (that is, if the same thermal regime for planet formation applies as in the solar system). This led to studies of the habitable zone around other stars, as well. Finally, we discovered that our data could be used to detect giant planets without transits as we had been carefully timing the eclipses of the stars (using a GPS antenna for time) and this will drift by being offset by any giant planets orbiting around the system, as well. The best summary of our work may be to just summarize the 21 refereed papers produced during the time of this grant. This will be done is chronological order and in each section separately.

Doyle, Laurance R.↗

Solar power from satellites

Microwave beaming of satellite-collected solar energy to earth for conversion to useful industrial power is evaluated for feasibility, with attention given to system efficiencies and costs, ecological impact, hardware to be employed, available options for energy conversion and transmission, and orbiting and assembly. Advantages of such a power generation and conversion system are listed, plausible techniques for conversion of solar energy (thermionic, thermal electric, photovoltaic) and transmission to earth (lasers, arrays of mirrors, microwave beams) are compared. Structural fatigue likely to result from brief daily eclipses, 55% system efficiency at the present state of the art, present projections of system costs, and projected economic implications of the technology are assessed. Two-stage orbiting and assembly plans are described.

Glaser, P. E.↗

On-Orbit Structural Dynamics Performance of the Roll-Out Solar Array

The Roll-Out Solar Array (ROSA) flight experiment was launched to the International Space Station (ISS) on June 3rd, 2017. ROSA is an innovative, lightweight solar array with a flexible substrate that makes use of the stored strain energy in its composite structural members to provide deployment without the use of motors. This paper will discuss the results of various structural dynamics experiments conducted on the ISS during the weeks following launch. Data gathered from instrumentation on the solar array wing during the experiments are compared with pre-flight predictions from two different finite element modeling efforts. Two distinct methods were used to reconstruct the modal characteristics of ROSA from the data collected on orbit. Of particular interest in this effort are the first few system modes and mode shapes of the array, the amount of structural damping present, and degree of structural thermal interaction seen during eclipse exit. Discrepancies between the behavior predicted by the models and that observed on orbit are identified and discussed. The goal in this effort was to better understand the performance of ROSA and to improve modeling efforts for future designs of similar solar arrays.

Chamberlain, Matthew K.↗

Epsilon Aurigae in eclipse. II - Optical absorption lines from the secondary

Optical high-resolution 2.7-m McDonald Observatory observations of Epsilon Aur obtained during the 1982-1985 eclipse are discussed, with focus on the K I resonance lines, some Fe II and Ti II lines in the blue, and the near-infrared N I excitation lines. The N I lines are immune to contamination by the secondary, and their radial velocity decline over the three-year interval fits the predicted velocity curve. The 7664 A and 7699 A K I lines strengthen greatly during the eclipse due to gas in orbit around the secondary passing in front of the primary, and the velocity pattern analysis indicates a mass of the secondary to solar mass ratio of between about 3 and 6 and a primary mass of 3 solar masses. The data are consistent with the picture of a low-mass post-AGB primary having lost mass through a wind and by Roche-lobe transfer to the secondary, and which will evolve to a white dwarf in less than 10,000 years.

Lambert, D. L.↗

HOW TO DETERMINE AN EXOMOON'S SENSE OF ORBITAL MOTION

We present two methods to determine an exomoon's sense of orbital motion (SOM), one with respect to the planet's circumstellar orbit and one with respect to the planetary rotation. Our simulations show that the required measurements will be possible with the European Extremely Large Telescope (E-ELT). The first method relies on mutual planet-moon events during stellar transits. Eclipses with the moon passing behind (in front of) the planet will be late (early) with regard to the moon's mean orbital period due to the finite speed of light. This ''transit timing dichotomy'' (TTD) determines an exomoon's SOM with respect to the circumstellar motion. For the 10 largest moons in the solar system, TTDs range between 2 and 12 s. The E-ELT will enable such measurements for Earth-sized moons around nearby Sun-like stars. The second method measures distortions in the IR spectrum of the rotating giant planet when it is transited by its moon. This Rossiter-McLaughlin effect (RME) in the planetary spectrum reveals the angle between the planetary equator and the moon's circumplanetary orbital plane, and therefore unveils the moon's SOM with respect to the planet's rotation. A reasonably large moon transiting a directly imaged planet like β Pic b causes an RME amplitude of almost 100 m s{sup –1}, about twice the stellar RME amplitude of the transiting exoplanet HD209458 b. Both new methods can be used to probe the origin of exomoons, that is, whether they are regular or irregular in nature.

79 ASTRONOMY AND ASTROPHYSICS↗

Ground test program for a full-size solar dynamic heat receiver

Test hardware, facilities, and procedures were developed to conduct ground testing of a full size, solar dynamic heat receiver in a partially simulated, low Earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment were designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed Brayton cycle engine simulator to circulate and condition the helium xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Sedgwick, L. M.↗

Ground test program for a full-size solar dynamic heat receiver

Test hardware, facilities, and procedures were developed to conduct ground testing of a full-size, solar dynamic heat receiver in a partially simulated, low earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment was designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed-Brayton cycle engine simulator to circulate and condition the helium-xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Sedgwick, L. M.↗

The Hubble PanCET Program: Transit and Eclipse Spectroscopy of the Strongly Irradiated Giant Exoplanet WASP-76b

Ultra-hot Jupiters with equilibrium temperatures greater than 2000 K are uniquely interesting targets as they provide us crucial insights into how atmospheres behave under extreme conditions. This class of giant planets receives intense radiation from their host star and usually has strongly irradiated and highly inflated atmospheres. At such a high temperature, cloud formation is expected to be suppressed and thermal dissociation of water vapor could occur. We observed the ultra-hot Jupiter WASP-76b with seven transits and five eclipses using the Hubble Space Telescope and the Spitzer Space Telescope (Spitzer) for a comprehensive study of its atmospheric chemical and physical processes. We detected TiO and H{sub 2}O absorption in the optical and near-infrared transit spectrum. Additional absorption by a number of neutral and ionized heavy metals like Fe, Ni, Ti, and SiO help explain the short-wavelength transit spectrum. The secondary eclipse spectrum shows muted water feature but a strong CO emission feature in Spitzer’s 4.5 μm band indicating an inverted temperature pressure profile. We analyzed both the transit and eclipse spectra with a combination of self-consistent PHOENIX models and atmospheric retrieval. Both spectra were well fitted by the self-consistent PHOENIX forward atmosphere model in chemical and radiative equilibrium at solar metallicity, adding to the growing evidence that both TiO/VO and NUV heavy metals opacity are prominent NUV-optical opacity sources in the stratospheres of ultra-hot Jupiters.

47 OTHER INSTRUMENTATION↗

Optical observations of Sanduleak 160.

The variability of Sanduleak 160, the proposed optical counterpart of SMC X-1, has been confirmed. It shows a double-peaked optical variation with the minimum at X-ray eclipse being the deeper. The cos 2 theta variation has a semiamplitude of 0.050 mag in the B filter, the cos theta variation has a semiamplitude of 0.025 mag, and there is a cos 3 theta variation of 0.012 mag semiamplitude. From an analysis of the optical photometry and X-ray eclipse duration the mass ratio is found to be 0.28, i = 79 deg, and P = 3.89206 days. On the assumption that the mass of Sk 160 is 20 solar masses, the mass of SMC X-1 is 5.6 solar masses.

Petro, L.↗

A hot companion to Mu Sagittarii - An opportunity to sound the atmosphere of a B8 Ia supergiant

It is argued that the bright supergiant star Mu Sagittarii is accompanied by a smaller and hotter star, of spectral type approximately B1.5 V. The single-line radial-velocity curve of the B8 star leads to a fairly large mass function, f(m) = 2.64 solar masses, implying that the companion should have at least 50 percent of the mass of the visible star. Older optical observations indicated the presence of a shallow eclipse at the time of the conjunction with the supergiant behind the companion. Since the Copernicus, IUE, and Voyager observations show that the companion is the hotter component, that eclipse must have been the secondary eclipse (if it was an eclipse at all). A deeper, primary eclipse has been predicted by Plavec in 1978. It was indeed observed as a marked decrease of the far-ultraviolet flux from the system both with the Copernicus and the IUE satellites. The presence of a hotter but smaller component in Mu Sagittarii offers a unique opportunity to study the outer atmospheric layers of a supergiant which is of a much earlier spectral type than the supergiants in the Zeta Aurigae systems.

Polidan, R. S.↗