ShARC/C3 Launcher Capabilities at NLV - Poster
Poster detailing the capabilities of the ShARC/C3 Launcher platform
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Poster detailing the capabilities of the ShARC/C3 Launcher platform
Waste repositories from surface trenches and shafts at Los Alamos to drilled tunnels at Yucca Mountain are being built in volcanic Tuff, a soft compacted material that is permeable to water and air. US Department of Energy documents on repository design identify the primary design goal of 'preventing water from reaching the waste canisters, dissolving the canisters and carrying the radioactive waste particles away from the repository'. Designers expect to achieve this by use of multiple barriers along with careful placement of the repository both well above the water table and well above the ground level in a mountain. Though repositories are located in areas that have a historically dry climate to minimize the impact of rainfall infiltration, global warming phenomena may have the potential to alter regional climate patterns - potentially leading to higher infiltration rates. Conventional methods of sealing fractures within volcanic tuff may not be sufficiently robust or long lived to isolate a repository shaft from water for the required duration. A new grouting technology based on molten wax shows significant promise for producing the kind of long term sealing performance required. Molten wax is capable of permeating a significant distance through volcanic tuff, as well as sealing fractures by permeation that is thermally dependent instead of chemically or time dependent. The wax wicks into and saturates tuff even if no fractures are present, but penetrates and fills only the heated area. Heated portions of the rock fill like a vessel. The taffy-like wax has been shown to waterproof the tuff, and significantly increase its resistance to fracture. This wax was used in 2004 for grouting of buried radioactive beryllium waste at the Idaho National Laboratory, chiefly to stop the water based corrosion reactions of the waste. The thermoplastic material contains no water and does not dry out or change with age. Recent studies indicate that this kind of wax material may be inherently resistant to bio-degradation. (authors)
Magnetic component designers are always looking for improved soft magnetic core materials to increase the efficiency, temperature rating and power density of transformers, motors, generators and alternators, and energy density of inductors. In this paper, we report on the experimental investigation of commercially available cobalt-based amorphous alloys which, in their processing, were subjected to two different types of magnetic field anneals: A longitudinal magnetic field anneal or a transverse magnetic field anneal. The longitudinal field annealed material investigated was Metglas 2714A. The electrical and magnetic characteristics of this material were investigated over the frequency range of 1 to 200 kHz and temperature range of 23 to 150 C for both sine and square wave voltage excitation. The specific core loss was lower for the square than the sine wave voltage excitation for the same maximum flux density, frequency and temperature. The transverse magnetic field annealed core materials include Metglas 2714AF and Vacuumschmelze 6025F. These two materials were experimentally characterized over the frequency range of 10 to 200 kHz for sine wave voltage excitation and 23 C only. A comparison of the 2174A to 2714AF found that 2714AF always had lower specific core loss than 2714A for any given magnetic flux density and frequency and the ratio of specific core loss of 2714A to 2714AF was dependent on both magnetic flux density and frequency. A comparison was also made of the 2714A, 2714AF, and 6025F materials to two different tape thicknesses of the polycrystalline Supermalloy material and the results show that 2714AF and 6025F have the lowest specific core loss at 100 kHz over the magnetic flux density range of 0.1 to 0.4 Tesla.
The instruments best suited to performing high-energy-resolution neutron spectroscopy are spin-echo spectrometers and backscattering spectrometers. The development of these experimental techniques dates back almost half a century, and most major neutron scattering facilities operate mature spectrometers of one or both classes. Recent advances in instrumentation and neutron sources are enhancing their performance and expanding their capabilities, with the objective of enabling researchers to tackle new and more complex problems. Finally, in this Technical Review, we assess the current state of the art in high-energy-resolution neutron spectrometers, showcasing their role in the study of nanoscale dynamics in soft and biological materials, as well as disordered magnets.
Recent studies on multinary oxides for applications as laser hosts and high dielectric capacitors have shown that processing at high temperature provides glassy or crystalline materials based on thermal treatments and cooling rates. Since hydroxyapatites are now subject of great interests due to their bioactivity, interest in producing soft and hard materials with glassy and crystalline nature by processing parameters has become very important. Crystalline materials by using Bridgman, Czochralski and flux growth methods are costly and require huge investment. We have observed that even low temperature solidification in organic flux produced oriented fibers. This organic treated material has different characteristics than in situ oxide materials prepared by sintering and grain growth. Examples of phosphate and silicate-based systems will be presented to demonstrate soft and hard materials. Effect of TiO2 and other hardening elements will be also reported.
Hydrogels are soft, water-absorbing polymer materials with diverse applications in biomedicine and agriculture. Recently, hydrogels have been proposed to encapsulate water-soluble phase change materials which store energy in their latent heat of solidification. In these applications, the thermal conductivity of these materials affects their performance. Few methods exist for measuring the thermal conductivity of small quantities of hydrogels. Here, we describe an implementation of the bidirectional 3w technique to measure the thermal conductivity of hydrogels with particular attention to their moisture content. Our implementation of the technique can probe sample volumes as little as ~20 mL and yields the thermal conductivity without requiring fitting of additional thermal parameters. We numerically simulate 3w sensor designs with frequency-domain 3-D models to quantify and reduce errors introduced by the choice of substrate and insulation layer thickness. Frequencies in the ~1−20 Hz range yield less error for the materials considered here. We verify our setup with measurements on water and report values for polyacrylamide and poly(2-acrylamido-2-methylpropane sulfonic acid) (PAMPS) hydrogels. Our swollen hydrogels exhibited thermal conductivities nearly equivalent to water, 0.6 W m-1 K-1, and we estimate thermal conductivities of 0.43 and 0.42 W m-1 K-1 for neat polyacrylamide and PAMPS, respectively. Finally, we estimate an error of ±7%, consistent with other 3ω methods, with the largest error coming from the sensor calibration. We find our implementation of the bidirectional 3w method gives reasonable results and can be employed for prototyping soft materials relevant for thermal storage.
Friction and wear induced mechanical failures may be controlled to extend the life of tribological components through the interposition of selected solid materials between contacting surfaces. Thin solid films of soft and hard materials are appropriate to lower friction and enhance the wear resistance of precision tribo-elements. Thin film coating technologies that have been developed may be used to interpose thin solid layers between contacting surfaces to reduce friction or to extend wear life. Film deposition technologies developed include chemical vapor deposition (CVD) and physical vapor deposition (PVD). Sputter coating is a PVD process for thin film deposition. It allows close control of coating thickness and composition and is well-suited for the deposition of tribological coatings. In this paper, the utility of magnetron sputtering for the deposition of tribological coatings is examined. Experimental results obtained when coated bodies are tested under a number of tribological operating conditions are presented. It is shown that when film adhesion problems are resolved, sputtering can be an effective means of depositing tribological coatings.
We have recently developed a soft-landing (SL) instrument that is capable of depositing ions onto substrates for preparative and developmental research of new materials using a laser ablation source. This instrument was designed with a custom drift tube and a split-ring ion optic for the isolation of selected ions. The drift tube allows for the separation and thermalization of ions formed after laser ablation through collisions with an inert bath gas. These collisions allow the ions to be landed at energies below 1 eV onto substrates. The split-ring ion optic is capable of directing ions toward the detector or a landing substrate for selected components. Experiments will be shown ablating Cu using an Nd:YAG (1064 and 532 nm) for cluster formation and landing onto a muscovite (mica) surface. The laser ablation of Cu in 8 Torr of He gas gives a spectrum that contains multiple peaks corresponding to Cu{sub n}, Cu{sub n}O{sub m} clusters, and their corresponding isomers. Atomic force microscopy and drift tube measurements were performed to characterize the performance characteristics of the instrument.
This paper describes the use of composite materials in the Soft X-Ray Telescope (SXT). One of the primary structural members of the telescope is a graphite epoxy metering tube. The metering tube maintains the structural stability of the telescope during launch as well as the focal length through various environmental conditions. The graphite epoxy metering tube is designed to have a negative coefficient of thermal expansion to compensate for the positive expansion of titanium structural supports. The focus is maintained to + or - 0.001 inch by matching the CTE of the composite tube to the remaining structural elements.
A research program is described which developes an understanding of high-temperature solid lubrication and experimental techniques through the development of a composite lubricant coating system. The knowledge gained through this research was then applied to a specific engineering challenge, the tribology of a sliding seal for hypersonic flight vehicles. The solid lubricant coating is a chromium carbide based composite combined with silver, which acts as a low temperature lubricant, and barium fluoride/calcium fluoride eutectic, which acts as a high-temperature lubricant. This composite coating provides good wear resistance and low friction for sliding contacts from room temperature to over 900 C in reducing or oxidative environments. The specific research on this coating included a composition screening using a foil gas bearing test rig and the use of thin silver films to reduce initial wear using a pin-on-disk test rig. The chemical stability of the materials used was also addressed. This research indicated that soft metallic films and materials which become soft at elevated temperatures are potentially good lubricants. The general results from the experiments with the model solid lubricant coating were then applied to a sliding seal design concept. This seal design requires that a braided ceramic fabric slide against a variety of metal counterface materials at temperatures from 25 to 850 C in an oxidative environment. A pin-on-disk tribometer was used to evaluate the tribological properties of these materials and to develop lubrication techniques. The results indicate that these seal materials must be lubricated to prevent wear and reduce friction. Thin films of silver, gold and calcium fluoride provided lubrication to the sliding materials.
The potential of fuzzy sets and neural networks, often referred to as soft computing, for aiding in all aspects of manufacturing of advanced materials like ceramics is addressed. In design and manufacturing of advanced materials, it is desirable to find which of the many processing variables contribute most to the desired properties of the material. There is also interest in real time quality control of parameters that govern material properties during processing stages. The concepts of fuzzy sets and neural networks are briefly introduced and it is shown how they can be used in the design and manufacturing processes. These two computational methods are alternatives to other methods such as the Taguchi method. The two methods are demonstrated by using data collected at NASA Lewis Research Center. Future research directions are also discussed.
The applications of resonant soft X-ray emission spectroscopy on a variety of carbon systems have yielded characteristic fingerprints. With high-resolution monochromatized synchrotron radiation excitation, resonant inelastic X-ray scattering has emerged as a new source of information about electronic structure and excitation dynamics. Photon-in/photon-out soft-X-ray spectroscopy is used to study the electronic properties of fundamental materials, nanostructure, and complex hydrides and will offer potential in-depth understanding of chemisorption and/or physisorption mechanisms of hydrogen adsorption/desorption capacity and kinetics.
Recycling crosslinked polyurethanes (PUs) is accomplished through mechanical or chemical processes that are energy-intensive or produce plastics of lesser value. Polymer recycling processes are notably intolerant of polymer mixtures, yet the ability to reprocess and compatibilize two or more crosslinked PUs together will make this process more amenable to mixed waste streams while offering an opportunity to tune the properties of the recycled polymer products. Here, we blend a rigid polyester PU and a soft polyether PU using twin-screw extrusion to yield materials with tunable mechanical properties based on the feed composition. Their material properties were compared to those of compression-molded reprocessed blends and blends where the monomers were mixed prior to synthesis. The extruded materials showed similar mechanical and thermal properties to newly prepared blends and had higher-value mechanical properties compared to the samples reprocessed via compression molding. The morphologies of the blends were observed using phase imaging via atomic force microscopy to show that there is less phase separation in the extruded materials compared to compression-molded blends. The mechanical properties of these materials were tunable from soft to elastomeric to rigid based on the feed composition, and this tunability was demonstrated through four consecutive reprocessing cycles, through which the mechanical properties were steadily varied from rigid to soft by incorporating increasing amounts of soft polyether PU material. Here, this blending method for reprocessing mixed waste compatibilizes different PUs and provides a means to tune the mechanical properties of a PU product, even if starting from waste streams of varying compositions. As such, this process represents an intriguing new approach for polymer reprocessing.
Abstract The synthesis of soft matter intelligence with circuit‐driven logic has enabled a new class of robots that perform complex tasks or conform to specialized form factors in unique ways that cannot be realized through conventional designs. Translating this hybrid approach to fluidic systems, the present work addresses the need for sheet‐based circuit materials by leveraging the innate porosity of foam—a soft material—to develop pneumatic components that support digital logic, mixed‐signal control, and analog force sensing in wearables and soft robots. Analytical tools and experimental techniques developed in this work serve to elucidate compressible gas flow through porous sheets, and to inform the design of centimeter‐sized foam resistors with fluidic resistances on the order of 10 9 Pa s m −3 . When embedded inside soft robots and wearables, these resistors facilitate diverse functionalities spanning both sensing and control domains, including digital logic using textile logic gates, digital‐to‐analog signal conversion using ladder networks, and analog sensing of forces up to 40 N via compression‐induced changes in resistance. By combining features of both circuit‐based and materials‐based approaches, foam‐enabled fluidic circuits serve as a useful paradigm for future hybrid robotic architectures that fully embody the sensing and computing capabilities of soft fluidic materials.
Recent studies have identified unique properties of organic battery electrode materials such as moderate redox potentials and mechanical softness which are uniquely beneficial for all-solid-state batteries based on ceramic electrolytes. Here, we further explore the promise of organic materials and demonstrate a sulfide electrolyte- based organic-lithium battery with a specific energy of 828 Wh kg –1 , rivaling the state-of- the-art of all-solid-state batteries. Two innovation steps are responsible for the accomplishment. First, the combination of lithium anode and the high-capacity cathode material pyrene-4,5,9,10-tetraone ensures a high theoretical specific energy. Second, the microstructure of the organic cathode is optimized with the introduction of cryomilling, a technique common to processing soft materials but not familiar to electrode fabrication. The cathode material utilization increases to 99.5% as a result, up from the 55–89% previously reported for ceramic electrolyte-based solid-state organic batteries. In conclusion, the improvement highlights the special requirements of solid-state organic electrodes for microstructural engineering while preserving the chemical integrity of components.
A combined magnetization and zero-field {sup 59}Co spin-echo nuclear magnetic resonance (NMR) study has been carried out on one member of a recently developed class of highly ordered mesoporous nanostructured materials, mesoporous Co{sub 3}O{sub 4} (designated UCT-8, University of Connecticut, mesoporous materials). The material was synthesized using one-step soft-templating by an inverse micelles packing approach. Characterization of UCT-8 by powder x-ray diffraction and electron microscopy reveals that the mesostructure consists of random close-packed Co{sub 3}O{sub 4} nanoparticles ≈ 12 nm in diameter. The N{sub 2} sorption isotherm for UCT-8, which is type IV with a type H1 hysteresis loop, yields a 134 m{sup 2}/g BET surface area and a 7.7 nm BJH desorption pore diameter. The effect of heat treatment on the structure is discussed. The antiferromagnetic Co{sub 3}O{sub 4} nanoparticles have a Néel temperature T{sub N} = 27 K, somewhat lower than the bulk. A fit to the Curie-Weiss law over the temperature range 75 K ≤ T ≤ 300 K yields an effective magnetic moment of μ{sub eff} = 4.36 μ{sub B} for the Co{sup 2+} ions, indicative of some orbital contribution, and a Curie-Weiss temperature Θ = −93.5 K, consistent with antiferromagnetic ordering. The inter-sublattice and intra-sublattice exchange constants for the Co{sup 2+} ions are J{sub 1}/k{sub B} = (−)4.75 K and J{sub 2}/k{sub B} = (−)0.87 K, respectively, both corresponding to antiferromagnetic coupling. The presence of uncompensated surface spins is observed below T{sub N} with shifts in the hysteresis loops, i.e., an exchange-bias effect. The {sup 59}Co NMR spectrum for UCT-8, which is attributed to Co{sup 2+} ions at the tetrahedral A sites, is asymmetrically broadened with a peak at ≈55 MHz (T = 4.2 K). Since there is cubic symmetry at the A-sites, the broadening is indicative of a magnetic field distribution due to the uncompensated surface spins. The spectrum is consistent with antiferromagnetically ordered particles that are nanometer in size and single domain.
The overarching goal of this research program, as originally delineated in the proposal “Tuning anisotropic bonding via chemistry and pressure in layered pnictides and chalcogenides” was to develop a predictive, chemistry-driven understanding of the impact of the phonon behavior on thermal properties of bulk layered materials. At finite temperatures, atomic vibrations (phonons) strongly impact the thermodynamics, thermal and electrical transport, and phase-switching properties of functional materials. In particular, soft phonon modes and strongly anharmonic potentials can have spectacular consequences, including structural phase transitions (for example in ferroelectrics and phase-change memory materials), metal-insulator transitions, and extreme thermal resistance preventing heat propagation. Bulk materials with highly-anisotropic bonding may provide unique strategies to induce soft-phonon modes and lattice instabilities. Recently, increasingly detailed investigations of the lattice dynamics in layered materials have been made possible by the advent of first-principles phonon calculations and advanced characterization techniques based on neutron and X-ray scattering. However, due to the lack of studies in which composition and bonding character are systematically varied, there are still fundamental questions regarding the impacts of anisotropic bonding and anharmonicity on lattice stability and thermal transport. One of the major goals of this research program is therefore to address this gap by coherently tuning bonding anisotropy and anharmonicity across families of related compounds. Such approaches have revealed new strategies for exploiting structural anisotropy in quasi-1D and 2D bulk materials to obtain tailored functional properties. This project systematically explored the lattice dynamics, phase stability, and transport properties in bulk layered materials by using both composition and applied pressure to tune the degree of bonding anisotropy and anharmonicity. To accomplish this work, we combined i) single-crystal growth of key material systems with tunable anisotropy, ii) in-situ high-temperature/high-pressure characterization of structure and phonons to probe bonding anisotropy and anharmonicity, including state-of-the-art inelastic X-ray scattering (IXS) and inelastic neutron scattering (INS), and iii) first-principles simulations leveraging large-scale computing to identify the fundamental origins of the observed effects, by relating atomic structure and dynamics to electronic orbital interactions. Finally, we modeled and verified the impact of the phonon behavior on thermal transport to identify new strategies for a-priori design of thermal conductivity. Our integrated collaborative approach helped to systematically unravel the effects of anisotropy and bonding anharmonicity on phonon transport, thermodynamics, and thermal properties of complex anisotropic materials.