Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sinter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel processing route for design and manufacturing of metal toughened nanoceramics: Al–Al 2 O 3 nanocermets

Monolithic alumina is a highly brittle ceramic with a very low fracture toughness, making it an unreliable material for mechanical and structural applications. Ceramic-metal composites (cermets) are the subject of intensive interest to obtain materials which can address the intrinsic brittleness of ceramics without compromising their high strength and light weight. In the present investigation, aluminium-alumina (Al–Al 2 O 3 ) nanocermets were developed. The nanocermets possessed the toughness of Al phase and the strength of reinforced nano Al 2 O 3 particles. Here, the nanocermets green bodies were prepared such that upon sintering each adjacent Al 2 O 3 grain was conformally coated with a continuous Al film. Mechanical milling via a combination of cryo-milling and ball-milling was used to prepare Al–Al 2 O 3 nano-powder mixture. Spark plasma sintering was used to consolidate the green nanocermets. Results show that specimens prepared from 35 h milled powders exhibited superior mechanical properties as compared to other nanocermets, with an improvement in microhardness, elastic modulus, compressive strength, and flexural strength by 88%, 78%, 69% and 40% with respect to sintered pure Al. The indentation toughness of 35 h milled nanocermet showed an increment of 12.5% with respect to sintered pure Al 2 O 3 . Characterization techniques such as XRD, SEM, HR-TEM, X-ray tomography were employed to investigate the phase evolution and structural morphology, while FEM simulations were performed for understanding the crack propagation mechanisms in nanocermets.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additive manufacturing of mullite ceramic by digital light processing

Mullite material was successfully additively manufactured using digital light processing (DLP). The printed geometry involves a one-step process of pyrolysis, de-binding, and sintering under a plain atmosphere to achieve an average of 76 % ceramic yield and linear shrinkage of 12 %. Furthermore, the thermal profile was carefully controlled to obtain consistent phases in which the XRD shows a mullite phase. Here, in addition, the Weibull analysis was conducted on the sintered flexural specimens, showing a Weibull modulus (m) of 13.05 with a characteristic strength (σ 0 ) of 94.96 MPa. Synchrotron microtomography was performed on the sintered specimens, which showed two distinct porosity distributions (small and large). Large porosity (non-spherical elongated) is the primary cause of decreased material strength, while small porosity (spherical) is the sintering product. The measured thermal conductivity of the specimens was in the range of 2.7–3.1 W/m∙k and decreased with an increase in temperature. Lastly, large-scale prototypes were printed concurrently with a fine resolution of 25 μm without any compromise on the predetermined design and structure.

Additive manufacturing↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct ink writing of boron carbide monoliths

Direct ink writing – an extrusion-based additive manufacturing process – followed by pressureless sintering was investigated to produce boron carbide monoliths. The effects of ceramic powder loading and Pluronic binder concentration on the rheology of boron carbide pastes were studied and linked to both processing behaviour and final outcome in terms of sintered density and hardness. The effects of printing parameters, in particular orifice diameter and printing speed, were also investigated. Reducing the size of the extrusion nozzle from 584 μm to 406 μm led to significantly better shape retention, lower surface roughness, as well as higher density and hardness. A 203 μm printing orifice was also trialled but was unsuccessful due to faster drying kinetics that occurred with smaller ceramic struts resulting in rapid warping and nozzle clogging. Carbon-black – 8 wt% relative to B 4 C – acted as an effective sintering aid to increase both density and hardness. After optimisation of feedstock and printing parameters, few-layer samples (3–5 layers) had a density as high as ~ 97 % TD and a hardness of ~ 30 GPa. On the other hand, 18-layer specimens had a sintered density of ~ 87 % TD, despite a fully dense microstructure, due to the formation of a 3D array of inter-strut pores. Nevertheless, several issues that arose during manufacturing and post-processing were detrimental to the density and structural integrity of printed specimens; these issues were identified, discussed, and suggestions for future work are provided in this report.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive manufacturing of AISI M2 tool steel by binder jetting (BJ): Investigation of microstructural and mechanical properties

The presented research demonstrates for the first time the successful processing of AISI M2 tool steel by binder jetting, a promising additive manufacturing technique capable of producing complex shapes with minimal residual stresses and isotropic properties. The optimal printing parameters were explored by varying processing parameters such as the binder saturation (45 %–105 %), binder set time (0 to 10 s), targeted bed temperature (50–60 °C), oscillator (2600–2750 rpm), recoater (20–28 mm/s), and roller speeds (200–300 rpm). Microstructural characterization and evaluation of mechanical properties of binder jetted parts were performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) to study their chemical composition, powder morphology, microstructure, carbide morphologies, relative density, hardness, compressive strength, and ductility. Two powder sizes (5 and 10 μm) were used, and sintering was performed at varying temperatures (1270, 1280, and 1300 °C) and durations (60 and 120 min), followed by a furnace, air, and water cooling. An optimum hardness of ~970 HV was obtained when parts were sintered at 1270 °C for 60 min, followed by water quenching. Impressive compressive strength of ~ 3580 MPa was observed in the sample sintered at 1280 °C for 60 min duration, followed by air cooling. Furnace-cooled parts showed the highest density of ~95 %, whereas the relative density of air- and water-cooled parts varied between ~91 to 93.50 %, respectively. The microstructure of sintered samples revealed the formation of M 6 C stable carbide, M 2 C metastable carbide, MC as a secondary carbide, and a-Fe matrix, which contributed to the observed increase in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗
DOE OSTI2021

Exploring the structural uniformity and integrity of protonic ceramic thin film electrolyte using wet powder spraying

Thin protonic ceramic electrolyte contributes to lower ohmic resistance and enhances electrochemical performance of protonic ceramic electrochemical cells. However, manufacturing of large-scale thin electrolyte remains a challenge. Wet powder spraying is an attractive technique to deposit <10 µm thin electrolyte when advanced atomizing techniques and optimized spraying process are integrated. Here ultrasonic atomization is integrated in the wet powder spray technique to reduce the thickness of electrolyte. Moreover, a parametric study is conducted to optimize the wet powder spray process to deposit uniform and crack-free electrolyte film. It is illustrated that tuning of solid loading rates and spray passes can affect the morphology of the as-sprayed electrolyte film, enabling the structural compactness of the sintered electrolyte layer. To maintain chemical stability of the electrolyte layer during sintering, effect of sintering temperature is further investigated to produce a physically thin, structurally dense, and chemically homogeneous electrolyte layer. The protonic ceramic electrochemical cells fabricated with optimized spraying and sintering parameters demonstrate excellent performance under both fuel cell and electrolysis modes. In addition, the cells exhibit remarkable structural integrity during redox and long-term stability tests.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Three-dimensional hierarchical nanoporous copper via direct ink writing and dealloying

Three-dimensional (3D) hierarchical nanoporous Cu (3DHNP-Cu) is synthesized using a combination of direct ink writing (DIW) based 3D printing, thermal sintering, and chemical dealloying of Mn–Cu alloys. Through tuning processing conditions such as ink composition and cooling rate (after sintering), with consideration of Mn loss during sintering, 3DHNP-Cu with fully bicontinuous nanostructures and negligible residual Mn can be produced after dealloying. The 3DHNP-Cu is comprised of structural features that span seven orders of magnitude, where DIW digitally controls macroscale porous features, thermal sintering and degradation of the binding polymer determines microscale porous features, and dealloying gives rise to nanoscale pores.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Templated encapsulation of platinum-based catalysts promotes high-temperature stability to 1,100 °C

Stable catalysts are essential to address energy and environmental challenges, especially for applications in harsh environments (for example, high temperature, oxidizing atmosphere and steam). In such conditions, supported metal catalysts deactivate due to sintering-a process where initially small nanoparticles grow into larger ones with reduced active surface area-but strategies to stabilize them can lead to decreased performance. In this work, we report stable catalysts prepared through the encapsulation of platinum nanoparticles inside an alumina framework, which was formed by depositing an alumina precursor within a separately prepared porous organic framework impregnated with platinum nanoparticles. These catalysts do not sinter at 800 °C in the presence of oxygen and steam, conditions in which conventional catalysts sinter to a large extent, while showing similar reaction rates. Extending this approach to Pd-Pt bimetallic catalysts led to the small particle size being maintained at temperatures as high as 1,100 °C in air and 10% steam. This strategy can be broadly applied to other metal and metal oxides for applications where sintering is a major cause of material deactivation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal, mechanical, and electrical properties of LSCo/mullite composite contact materials for solid oxide fuel cells

Lanthanum strontium cobaltite (LSCo) is considered as a good candidate cathode contact material for solid oxide fuel cells, due to high electrical conductivity. However, LSCo has a very large coefficient of thermal expansion (CTE) than the cells and metallic interconnects. As a result, poor mechanical stability is expected during thermal cycling. To minimize the CTE mismatch, we investigate a composite approach involving mixing LSCo with an inert material of low CTE, such as mullite at volume fractions from 0.1 to 0.4. Composite’s CTE shows a decreasing trend with increasing mullite volume fractions, and is consistent with model predictions. X-ray powder diffraction analysis of sintered LSCo/mullite composites exhibits no presence of other phases for samples aged for 500h at 800oC, indicating chemical compatibility. Electrical conductivity by a 4-pt method shows a decreasing trend with increasing mullite content. Contact strength of as-sintered and thermally cycled samples show that only the composite with 0.4 volume fraction has a measurable strength; the other composites have no strength. Overall, the composite approach is demonstrated in the LSCo/mullite system to lower the CTE and hence achieve thermal cycle stability. The addition of the inert phase to the LSCo matrix; however, also reduces the electrical conductivity.

Contact materials, LSCo, mullite, CTE, electrical ↗
DOE OSTI2022

Mass Transport in Binary TiO 2 :SiO 2 and GeO 2 :SiO 2 Direct Ink Write Glasses

The mass transport mechanisms of Ti in TiO 2 :SiO 2 and Ge in GeO 2 :SiO 2 direct ink write, additively manufactured glasses were studied. Due to the low solubility of Ti in SiO2 and high melting point of TiO 2 relative to SiO 2 , Ti transport was found to occur via solid state interdiffusion between adjoining SiO 2 and TiO 2 precursor particles. The diffusivity of titanium in SiO 2 measured over typical sintering temperatures (1000-1300 °C) using Rutherford backscattering spectrometry was D = 9.1 × 10 -7 [m2/sec] exp ($\frac{378[\frac{kJ}{mol}]}{RT}$. This provides an estimate of ~30 nm for the diffusion length under typical sintering conditions (2 hrs. at 1200 °C). Although Ti and Ge have similar diffusivities in SiO 2 glass at low concentrations, GeO 2 was found to be much more mobile during the sintering of printed GeO 2 :SiO 2 green bodies. This was evident in glasses with phase separated GeO 2 regions over length scales of ~10 μm and in experiments involving binary xerogels in which GeO 2 migrated over ~10 μm through cracked, porous SiO 2 layers. Large phase separated regions and long transport lengths in GeO 2 :SiO 2 suggest that the transport of GeO 2 occurs prior to the densification of the SiO 2 matrix via an alternative mechanism such as capillary flow. These results inform important considerations in the design of index modifying inks for the direct ink write process, namely initial precursor phase, mutual solubility with the base SiO 2 glass, and mass transport throughout the sintering process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Temperature-Swing Synthesis of Large-Size Single-Crystal LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Materials

Single-crystal lithium-nickel-manganese-cobalt-oxide (SC-NMC) has recently emerged as a promising battery cathode material due to its outstanding cycle performance and mechanical stability over the tradional polycrystalline NMC. It is favorable to further increase the grain size of SC-NMC particles to achieve a higher volumetric energy density and minimize surface-related degradations. However, the preparation of large-size yet high performance SC-NMC particles faces a challenge in choosing a suitable temperature for sintering. High temperature promotes grain growth but induces cation mixing that negatively impacts the electrochemical performance. Here we report a temperature-swing sintering (TSS) strategy with two isothermal stages that fulfils the needs for grain growth and structural ordering sequentially. A high-temperature sintering is first used for a short period of time to increase grain size and then the reaction temperature is lowered and kept constant for a longer period of time to improve structural ordering and complete the lithiation process. SC-LiNi 0.6 Mn 0.2 Co 0.2 O 2 materials prepared via TSS exhibit large grain size (~4 μm), a low degree of cation mixing (~0.9%), and outperform the control samples prepared by the conventional sintering method. Furthermore, this work highlights the importance of understanding the process-structure-property relationships and may guide the synthesis of other SC Ni-rich cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Diffraction and thermal effect of a Bessel-Gaussian laser for Ag nanoparticle deposition

Nanoparticles are known to sinter at much lower temperatures than the corresponding bulk or micro size particles. A laser-assisted sintering process is considered in this study to sinter Ag nanoparticles by dispensing Ag paste onto an indium tin oxide-coated Si substrate. The Gaussian beam of a CO 2 laser source is propagated through axicon and biconvex lenses, and the resulting hollow beam is focused on the Ag paste with a hollow parabolic mirror. A Bessel-Gaussian irradiance distribution is obtained at the focal plane of the parabolic mirror due to the interference of the hollow laser cone. The Fresnel diffraction approximation is considered to determine the phasor of the laser and an analytical approach is implemented to calculate the irradiance distribution of the Bessel-Gaussian beam. This irradiance distribution is utilized as a heat source in a heat conduction model and the temperature distribution is analyzed for thin Ag films formed during the laser sintering of Ag nanoparticles. An analytical expression is obtained for the temperature distribution by solving the heat conduction equation using Fourier transform for finite media. The widths of the deposited Ag lines are predicted from the temperature profiles and the model predictions compare well with the experimental results. The isotherms are found to be geometrically noncongruent with convex and concave tips depending on the locally maximum and minimum irradiances of the Bessel-Gaussian beam, respectively. The convex and concave tips, however, appear in the same isotherm for sufficiently high substrate speed relative to the laser beam.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Dissolution of Additively Manufactured Mo Disks and Structures for Accelerator Based Production of Mo-99

The press-and-sinter approach for production of Mo targets has been successfully tested and demonstrated. The main advantage of this process is that it uses readily available technology and tools that have been tuned for production of various metal and metal oxide targets. However, certain target design specifications, such as dimensional accuracy of the diameter and thickness of the disks, are required for proper fit into a target holder and therefore place strict tolerances on sintered Mo disks intended for accelerator production. Furthermore, having a target composed of multiple disks poses certain challenges for post-irradiation processing, where there is a potential for spillage of individual disks during the manipulation for dissolution inside a processing hot cell. Additive manufacturing (AM), also referred to as 3D printing, provides capabilities to design and build a single-piece Mo target that provides the opportunity for better geometry for optimized production of Mo-99, improved cooling capability, and safer post-irradiation handling. A drawback of AM Mo structures is roughness of finished surfaces, which could reduce the effectiveness of gas cooling systems. Process development for AM Mo structures using selective laser melting is described in work by Gibson and Lowden. For post-irradiation processing, it is important to look at the dissolution behavior of AM Mo structures in comparison to readily dissolved press-and-sinter Mo targets. The dissolution behavior of press-and-sinter targets has been well documented in our previous reports. In this report, we discuss results of dissolution experiments conducted with AM Mo disks and structures (provided by Oak Ridge National Laboratory [ORNL]) in 50% hydrogen peroxide (H 2 O 2 ).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Predicting Selective Laser Printing Print Quality of Polymer Powders through Melt Flow Index

Selective Laser Sintering (SLS) uses a precisely controlled laser to fuse polymer powder to build complex 3D shapes. While SLS covers a wide application space, the processing knowledge of polymer powder is limited, restricting the number of commercial powders available. This study serves to expand the processing knowledge of polypropylene and polyethylene in parallel with a “mature” SLS feedstock, nylon, through melt flow index (MFI) characterization. Differential Scanning Calorimetry (DSC) was used to explore the sintering window of the polymers. Polyethylene and polypropylene exhibited a relatively narrow sintering window between 4 – 5 °C, whereas the sintering window of nylon was much wider, between 23 – 24 °C. This suggests that the print quality between polyethylene and polypropylene would be similar; however, X-ray computed tomography revealed a higher volume of print defects, voids, and de lamination in polyethylene than in polypropylene. MFI analysis provided additional insight into the difference in print quality, as the MFI of polyethylene was 7.16 g/10 min, 9.95 g/10 min for polypropylene, and 17.23 g/10 min for nylon. MFI is inversely correlated to melt viscosity, and a low melt viscosity is desired for proper coalescing between the layers and particles. These results suggest that MFI is a promising tool, in conjunction with traditional thermal analysis, for screening candidate powder feedstocks for SLS and optimization of print parameters for novel powders.

36 MATERIALS SCIENCE↗
DOE OSTI2025

UN Synthesis, Fabrication, and Characterization and UC Oxidation Study in support of Advanced LEU Fuel Concepts

Uranium nitride and carbide-based fuels are proposed for use in advanced LEU fuel systems. This report details recent development work to study synthesis, sintering and fabrication methods for single phase UN in monolithic geometries. These samples were intended to support a variety of irradiation testing conditions by tailoring enrichment, geometry, and compositional requirements. Two methods were under evaluation for synthesizing uranium nitride powder – carbothermic reduction-nitridation (CTR-N) of UO 2 powder feedstock and hydride-dehydride/nitridation (HDN) of uranium metal feedstock. Pellets were fabricated from powder feedstocks via conventional pressing and sintering methods. As-fabricated feedstocks and pellets were evaluated via X-ray diffraction (XRD) for phase purity and sintered materials were characterized for density. Both the CTR N and the HDN methods were successfully demonstrated as an effective process for fabricating phase pure UN. Additionally, results from machining efforts for UN are detailed. This report also contains information on a study trying to elucidate the oxidation mechanisms of sintered uranium carbide samples fabricated from feedstock synthesized via an arc-melting method.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1977

Fabrication of thin layer beta alumina

Beta alumina tubes having walls 700 microns, 300 microns, and 140 microns were processed by extrusion and sintering utilizing Ford proprietary binder and fabrication systems. Tubes prepared by this method have properties similar to tubes prepared by isostatic pressing and sintering, i.e. density greater than 98% of theoretical and a helium leak rate less than 3 x 10 to the -9th power cc/sq cm/sec. Ford ultrasonic bonding techniques were used for bonding beta alumina end caps to open ended beta -alumina tubes prior to sintering. After sintering, the bond was hermetic, and the integrity of the bonded area was comparable to the body of the tube.

Tennenhouse, G. J.↗