Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sharp features”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Low-speed experimental study of the vortex flow effects of a fighter forebody having unconventional cross-section

A low speed wind tunnel investigation is conducted for the vortex flow characteristics of a tailless fighter configuration that features full length, fuselage-blended forebody strakes. Static pressure distributions were obtained on the forebody upper surface, and six-component forces and moments were measured on the complete, 60-deg cropped delta wing-fuselage-centerline vertical fin model at angles of attack and sideslip respectively reaching 50 deg and + or - 20 deg. The surface pressure data reveal that development of concentrated vortices from the sharp edged forebody strakes occurred at moderate and high angles of attack. The blended forebody was effective in capturing the windward vortical flow up to high incidence and sideslip angles. The direct suction effect of the windward vortex on the forebody sidewall was the primary contributor to static directional stability at high angles of attack. These improvements are potentially offset, however, by reduced or unstable roll and yaw damping.

Erickson, G. E.↗
NASA NTRSDate not supplied

Acid Alteration of Clay Minerals With Implication for Mars’ Surface Processes

The co-occurrence of phyllosilicates (clays) and sulfate stratigraphies at many locations on Mars are associated with a sharp change in surface conditions from neutral/alkaline pH during the Noachian (4.1-3.7 Ga) which favored the formation of clays to acidic conditions during the Hesperian (3.7-2.9 Ga) which favored the formation of sulfates. Yet, if these two contrasting geosystems were temporarily sequential, it is unknown how the Hesperian acidic conditions altered the previously formed clay units. We performed laboratory batch experiments to fingerprint the diagnostic features produced during interactions of Mars-analog clays and acidic solutions. Two clays, and silicon (IV) oxide, were reacted with solution of either sulfuric acid or filtered natural acid rock drainage (ARD) in plastic bottles. The solutions were adjusted at four pH values (1, 3, 5, and 7) and reacted at 4, 30, and 80°C for 3, 7, and 14 days. At the end of the experiments, the filtered supernatants were analyzed by ICP-MS while the solids were characterized by X-Ray Diffraction; Energy-Dispersive X-Ray Fluorescence analyses; Raman and Short-Wave Infrared spectroscopies and Scanning Electron Microscopy. Results show that the solution chemistry played a key role in the evolution of the clay-solution systems. In H2SO4 systems, the solution pH steadily increased due to partial clay dissolution with no secondary phase formation detected. Contrary, in the ARD systems, the pH decreased due to the ample presence of Fe which controlled both the reactivity of clays by the growth of protecting surface coatings and the solution pH by the precipitation of Fe nanophases; secondary phase detected included goethite, jarosite, gypsum, and siderite. These results indicate that, on Mars, the chemical interaction between clays and acidic solutions was complex and dependent on the solution chemistry. Acidic, sulfate-rich solutions have a high dissolution capacity and could have induced widespread clay disintegration. Notably, if Fe-rich ARD was involved, the clays on Mars could have remained stable during acidic Hesperian period due to formation of protective coatings. Comparison of our results with martian observations will be performed to determine how acidic conditions could potentially affect clays in sedimentary settings, including the Gale crater.

L. Lefticariu↗
NASA NTRS1977

The response of the dayside aurora to sharp northward and southward transitions of the interplanetary magnetic field and to magnetospheric substorms

Latitudinal shifts of the discrete dayside aurora are examined with respect to variations in the interplanetary magnetic field (IMF) and to magnetospheric substorms. Within 10-15 min after steplike southward (northward) transitions in the IMF the dayside auroral oval moves equatorward (poleward). In at least some cases the auroral shift is similar to an exponential relaxation in latitude from an initial to a final steady state value; for these cases the average exponential time constant is estimated to be 17 min. Substorm features in the dayside aurora include (1) an equatorward shift by 1-3 deg of the equatorward discrete auroral boundary, (2) a brightening of the discrete aurora near substorm onset, (3) the formation of multiple auroral bands, and (4) poleward motion of short-lived individual auroral arcs occurring nearly coincident in time with the equatorward boundary shifts, the average poleward velocity of these arcs being approximately 800 m/s.

Horwitz, J. L.↗
NASA NTRS1987

Dynamical features of the plasma-sheet ion composition, density, and energy

The effects of changes in solar and geomagnetic activity on the major plasma-sheet ions are investigated on the basis of a statistical analysis of 1500 h of data obtained at distances 10-23 earth radii and energy/charge ratios 0.1-16 keV/e by the ISEE-1 energetic-ion mass spectrometer. The results are presented in extensive graphs and discussed in detail. It is found that substorm activity is accompanied by a significant decrease in the density of solar-origin H(+) ions, a sharp increase in the energy per nucleon of both H(+) and He(+) ions, and an increase in the density of terrestrial O(+) ions. A factor-of-three increase in the overall O(+) density over the observation period is attributed to an increase in the solar EUV flux.

Lennartsson, W.↗
DOE OSTI2016

High fidelity simulation and analysis of liquid jet atomization in a gaseous crossflow at intermediate Weber numbers

Recent advances in numerical methods coupled with the substantial enhancements in computing power and the advent of high performance computing have presented first principle, high fidelity simulation as a viable tool in the prediction and analysis of spray atomization processes. The credibility and potential impact of such simulations, however, has been hampered by the relative absence of detailed validation against experimental evidence. The numerical stability and accuracy challenges arising from the need to simulate the high liquid-gas density ratio across the sharp interfaces encountered in these flows are key reasons for this. In this work we challenge this status quo by presenting a numerical model able to deal with these challenges, employing it in simulations of liquid jet in crossflow atomization and performing extensive validation of its results against a carefully executed experiment with detailed measurements in the atomization region. We then proceed to the detailed analysis of the flow physics. The computational model employs the coupled level set and volume of fluid approach to directly capture the spatiotemporal evolution of the liquid-gas interface and the sharp-interface ghost fluid method to stably handle high liquid-air density ratio. Adaptive mesh refinement and Lagrangian droplet models are shown to be viable options for computational cost reduction. Moreover, high performance computing is leveraged to manage the computational cost. The experiment selected for validation eliminates the impact of inlet liquid and gas turbulence and focuses on the impact of the crossflow aerodynamic forces on the atomization physics. Validation is demonstrated by comparing column surface wavelengths, deformation, breakup locations, column trajectories and droplet sizes, velocities, and mass rates for a range of intermediate Weber numbers. Analysis of the physics is performed in terms of the instability and breakup characteristics and the features of downstream flow recirculation, and vortex shedding. Formation of “Λ” shape windward column waves is observed and explained by the combined upward and lateral surface motion. The existence of Rayleigh-Taylor instability as the primary mechanism for the windward column waves is verified for this case by comparing wavelengths from the simulations to those predicted by linear stability analyses. Physical arguments are employed to postulate that the type of instability manifested may be related to conditions such as the gas Weber number and the inlet turbulence level. The decreased column wavelength with increasing Weber number is found to cause enhanced surface stripping and early depletion of liquid core at higher Weber number. A peculiar “three-streak-two-membrane” liquid structure is identified at the lowest Weber number and explained as the consequence of the symmetric recirculation zones behind the jet column. It is found that the vortical flow downstream of the liquid column resembles a von Karman vortex street and that the coupling between the gas flow and droplet transport is weak for the conditions explored.

42 ENGINEERING↗
NASA NTRS1972

The Apollo 15 X-ray fluorescence experiment.

The prime purpose of the X-ray fluorescence spectrometer carried in the Scientific Instrument Module of the Command-Service Module was to map the lunar surface with respect to its chemical composition. Results are presented for Al, Mg, and Si as Al/Si and Mg/Si ratios for the various features overflow by the spacecraft. The lunar surface measurements involved observations of the intensity and characteristic energy distribution of the secondary or fluorescent X rays produced by the interaction of solar X rays with the lunar surface. The results showed that the highlands and maria are chemically different, with the highlands having considerably more Al and less Mg than the maria. The mare-highland contact is quite sharp and puts a limit on the amount of horizontal transport of material. The X-ray data suggest that the dominant rock type of the lunar highlands is a plagioclase-rich pyroxene bearing rock probably anorthositic gabbro or feldspathic basalt.

Adler, I.↗
NASA NTRS1990

A time-accurate adaptive grid method and the numerical simulation of a shock-vortex interaction

A time accurate, general purpose, adaptive grid method is developed that is suitable for multidimensional steady and unsteady numerical simulations. The grid point movement is performed in a manner that generates smooth grids which resolve the severe solution gradients and the sharp transitions in the solution gradients. The temporal coupling of the adaptive grid and the PDE solver is performed with a grid prediction correction method that is simple to implement and ensures the time accuracy of the grid. Time accurate solutions of the 2-D Euler equations for an unsteady shock vortex interaction demonstrate the ability of the adaptive method to accurately adapt the grid to multiple solution features.

Bockelie, Michael J.↗
NASA NTRS1993

The red edge in arid region vegetation: 340-1060 nm spectra

The remote sensing study of vegetated regions of the world has typically been focused on the use of broad-band vegetation indices such as NDVI. Various modifications of these indices have been developed in attempts to minimize the effect of soil background, e.g., SAVI, or to reduce the effect of the atmosphere, e.g., ARVI. Most of these indices depend on the so-called 'red edge,' the sharp transition between the strong absorption of chlorophyll pigment in visible wavelengths and the strong scattering in the near-infrared from the cellular structure of leaves. These broadband indices tend to become highly inaccurate as the green canopy cover becomes sparse. The advent of high spectral resolution remote sensing instrument such as the Airborne Visible and Infrared Imaging Spectrometer (AVIRIS) has allowed the detection of narrow spectral features in vegetation and there are reports of detection of the red edge even for pixels with very low levels of green vegetation cover by Vane et al. and Elvidge et al., and to characterize algal biomass in coastal areas. Spectral mixing approaches similar to those of Smith et al. can be extended into the high spectral resolution domain allowing for the analysis of more endmembers, and potentially, discrimination between material with narrow spectral differences. Vegetation in arid regions tends to be sparse, often with small leaves such as the creosote bush. Many types of arid region vegetation spend much of the year with their leaves in a senescent state, i.e., yellow, with lowered chlorophyll pigmentation. The sparseness of the leaves of many arid region plants has the dual effect of lowering the green leaf area which can be observed and of allowing more of the sub-shrub soil to be visible which further complicates the spectrum of a region covered with arid region vegetation. Elvidge examined the spectral characteristics of dry plant materials showing significant differences in the region of the red edge and the diagnostic ligno-cellulose absorptions at 2090 nm and 2300 nm. Ray et al. detected absorption at 2100 nm in AVIRIS spectra of an abandoned field known to be covered by a great deal of dead plant litter. In order to better study arid region vegetation remote sensing data, it is necessary to better characterize the reflectance spectra of in situ, living, arid region plants.

Ray, Terrill W.↗
DOE OSTI2019

Corrosion Behavior of Pipeline Steel with Different Microstructures Under AC Interference in Acid Soil Simulation Solution

Corrosion behavior of X65 pipeline steels with different microstructures under alternating current (AC) interference was investigated in acid soil simulation solution by potentiodynamic polarization curve, potentiostatic polarization curve and immersion test. The results show that superimposed AC causes a sharp increase in corrosion current density of X65 steel. With the increase in i{sub AC}, the corrosion current densities of steels with various microstructures increase, especially at high i{sub AC}. Hot-rolled steel mainly experiences uniform corrosion, with very slight pit corrosion. Serious corrosion degrees with intensive corrosion pits can be observed on the surfaces of normalized and quenched microstructure steels. The annealed steel exhibits the feature of non-uniform corrosion with some pitting. The steels with various microstructures applied with AC have different corrosion resistance. The normalized steel shows the worst corrosion resistance, then the quenched microstructure, and the hot-rolled steel displays the optimum corrosion resistance. The difference in the microstructure can result in difference in corrosion degree and occurrence position of pitting corrosion of X65 steel. The normalized microstructure composed of polygonal ferrite and a large amount of pearlite and bainite is the most susceptible to AC corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Electrode Geometry on the Classification Performance of Rapid Evaporative Ionization Mass Spectrometric (REIMS) Bacterial Identification

The recently developed automated, high-throughput monopolar REIMS platform is suited for the identification of clinically important microorganisms. Although already comparable to the previously reported bipolar forceps method, optimization of the geometry of monopolar electrodes, at the heart of the system, holds the most scope for further improvements to be made. For this, sharp tip and round shaped electrodes were optimized to maximize species-level classification accuracy. Following optimization of the distance between the sample contact point and tube inlet with the sharp tip electrodes, the overall cross-validation accuracy improved from 77% to 93% in negative and from 33% to 63% in positive ion detection modes, compared with the original 4 mm distance electrode. As an alternative geometry, round tube shaped electrodes were developed. Geometry optimization of these included hole size, number, and position, which were also required to prevent plate pick-up due to vacuum formation. Additional features, namely a metal “X”-shaped insert and a pin in the middle were included to increase the contact surface with a microbial biomass to maximize aerosol production. Following optimization, cross-validation scores showed improvement in classification accuracy from 77% to 93% in negative and from 33% to 91% in positive ion detection modes. Supervised models were also built, and after the leave 20% out cross-validation, the overall classification accuracy was 98.5% in negative and 99% in positive ion detection modes. This suggests that the new generation of monopolar REIMS electrodes could provide substantially improved species level identification accuracies in both polarity detection modes. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2013

Communication: Thermodynamic analysis of critical conditions of polymer adsorption

Polymer adsorption to solid surfaces is a ubiquitous phenomenon, which has attracted long-lasting attention. Dependent on the competition between the polymer-solid adsorption and polymer-solvent solvation interactions, a chain may assume either 3d solvated conformation when adsorption is weak or 2d adsorbed conformation when adsorption is strong. The transition between these conformations occurring upon variation of adsorption strength is quite sharp, and in the limit of “infinite” chain length, can be treated as a critical phenomenon. We suggest a novel thermodynamic definition of the critical conditions of polymer adsorption from the equality of incremental chemical potentials of adsorbed and free chains. We show with the example of freely jointed Lennard-Jones chains tethered to an adsorbing surface that this new definition provides a link between thermodynamic and geometrical features of adsorbed chains and is in line with classical scaling relationships for the fraction of adsorbed monomers, chain radii of gyration, and free energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A semblance measure for model comparison

Algorithmic and computational advances have made it possible that geophysical survey and earth model design can be aided by many systematic trial inverse-modelling runs with synthetic data. Such may, for example, come up in machine-learning approaches. Automated image appraisal pertaining to such applications will involve common statistical tests for goodness-of-data fit as a primary evaluation method. However, solution non-uniqueness may render multiple images equivalent in terms of their data fit, requiring secondary categorizers. A logical choice for classifying synthetic-imaging results quantifies the goodness of model fit where a known reference model replaces the observational input. The task of model intercomparison in terms of measuring the resemblance to the reference model poses challenges to common distance-based metrics like root mean square error and mean absolute error. First, distance-based metrics can introduce spurious contributions when smooth models with fuzzy target contours are to be compared against a sharp reference. Second, large differences due to parameter-estimation overshoots can dominate distance metrics. Here, we propose a remedy that is referred to as semblance and is based on the idea of logistic functions, where a binary-dependent variable adds non-zero or zero accumulation terms for the, respectively, passing or failing of preset target thresholds. This classifying approach is amenable to an objective where model feature recognition is primary. Numerical comparisons to distance-based metrics provide evidence for the advantages of the semblance in view of this objective. Geophysical imaging in conjunction with machine-learning is seen as a benefitting upcoming application area.

58 GEOSCIENCES↗
NASA NTRS1973

Mars: Fretted and chaotic terrains

Fretted Martian terrain is characterized by smooth, flat, lowland areas separated from a cratered upland by abrupt escarpments of complex planimetric configuration and a maximum estimated height approaching 1 to 2 km. It is the product of some unusual erosive or abstractive process that has created steep escarpments. Chaotic terrain differs from fretted terrain in having a rough floor topography featuring a haphazard jumble of large angular blocks, and by arc-shaped slump blocks on its bounding escarpments. Its existence has now been confirmed by Mariner 9 pictures, and the characteristics, location, and areal extent of chaotic terrain have been more accurately and completely defined.

Sharp, R. P.↗
NASA NTRS1979

Low speed airfoil design and analysis

A low speed airfoil design and analysis program was developed which contains several unique features. In the design mode, the velocity distribution is not specified for one but many different angles of attack. Several iteration options are included which allow the trailing edge angle to be specified while other parameters are iterated. For airfoil analysis, a panel method is available which uses third-order panels having parabolic vorticity distributions. The flow condition is satisfied at the end points of the panels. Both sharp and blunt trailing edges can be analyzed. The integral boundary layer method with its laminar separation bubble analog, empirical transition criterion, and precise turbulent boundary layer equations compares very favorably with other methods, both integral and finite difference. Comparisons with experiment for several airfoils over a very wide Reynolds number range are discussed. Applications to high lift airfoil design are also demonstrated.

Eppler, R.↗
NASA NTRS1972

The Apollo 15 X-ray fluorescence experiment

The CSM spectrometric data on the lunar surface with respect to its chemical composition are presented for Al, Mg, and Si as Al/Si and Mg/Si ratios for the various features overflow by the spacecraft. The lunar surface measurements involved observations of the intensity and characteristic energy distribution of the secondary or fluorescent X-rays produced by the interaction of solar X-rays with the lunar surface. The results showed that the highlands and maria are chemically different, with the highlands having considerably more Al and less Mg than the maria. The mare-highland contact is quite sharp and puts a limit on the amount of horizontal transport of material. The X-ray data suggest that the dominant rock type of the lunar highlands is a plagioclase-rich pyroxene bearing rock, probably anorthositic gabbro or feldspathic basalt. Thus the moon appears to have a widespread differentiated crust (the highlands) systematically richer in Al and lower in Mg than the maria. This crust is pre-mare and may represent the first major internal differentiation of the moon.

Adler, I.↗
DOE OSTI2014

Evidence for spin glass state of NdCo{sub 1−x}Ni{sub x}O{sub 3} (x = 0.3−0.5)

Low-temperature magnetic properties of single phase NdCo{sub 1−x}Ni{sub x}O{sub 3}(x = 0.3−0.5) have been studied using ac and dc magnetic susceptibility measurements. Nickel substituted samples have been found to exhibit a different magnetic state at low temperature as compared to pristine NdCoO{sub 3}. The temperature dependent dc magnetization M (T) revealed the presence of a sharp cusp occurring at characteristic temperatures T{sub P}, for x = 0.3, 0.4, 0.5. Below T{sub P}, clear effect of magnetic field can be seen in M (T) curves and T{sub P} decreases with increasing magnetic field as well as Ni substitution content. The isothermal magnetization measurements at low temperatures shows small unsaturated hysteresis loop at lowest temperature (10 K). The ac susceptibility results show a clear frequency dependent feature. These results are analyzed to distinguish superparamagnetic and spin glass behavior by using Néel-Arrhennius, Vogel-Fulcher law, and power law fitting. This analysis ruled out the superparamagnet like state and suggests the presence of significant inter-cluster interactions, giving rise to spin-glass like cooperative freezing.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Characterization of chromium impurities in β -Ga2O3

Chromium is a common transition-metal impurity that is easily incorporated during crystal growth. It is perhaps best known for giving rise to the 694.3 nm (1.786 eV) emission in Cr-doped Al2O3, exploited in ruby lasers. Chromium has also been found in monoclinic gallium oxide, a wide-bandgap semiconductor being pursued for power electronics. In this work, we thoroughly characterize the behavior of Cr in Ga2O3 through theoretical and experimental techniques. β-Ga2O3 samples are grown with the floating zone method and show evidence of a sharp photoluminescence signal, reminiscent of ruby. We calculate the energetics of formation of Cr from first principles, demonstrating that Cr preferentially incorporates as a neutral impurity on the octahedral site. Cr possesses a quartet ground-state spin and has an internal transition with a zero-phonon line near 1.8 eV. By comparing the calculated and experimentally measured luminescence lineshape function, we elucidate the role of coupling to phonons and uncover features beyond the Franck–Condon approximation. The combination of strong emission with a small Huang–Rhys factor of 0.05 and a technologically relevant host material renders Cr in Ga2O3 attractive as a quantum defect.

Turiansky, Mark E. (ORCID:0000000291543582)↗
DOE OSTI2024

Large magnetoresistance and first-order phase transition in antiferromagnetic single-crystalline EuAg 4 Sb 2

Here, we present the results of a thorough investigation of the physical properties of EuAg 4 Sb 2 single crystals using magnetization, heat capacity, and electrical resistivity measurements. High-quality single crystals, which crystallize in a trigonal structure with space group 𝑅⁢$\bar{3}$𝑚, were grown using a conventional flux method. Temperature-dependent magnetization measurements along different crystallographic orientations confirm two antiferromagnetic phase transitions around 𝑇 𝑁⁢1 = 10.5K and 𝑇 𝑁⁢2 = 7.5K. Isothermal magnetization data exhibit several metamagnetic transitions below these transition temperatures. Antiferromagnetic phase transitions in EuAg 4 Sb 2 are further confirmed by two sharp peaks in the temperature-dependent heat capacity data at 𝑇 𝑁⁢1 and 𝑇 𝑁⁢2 , which shift to lower temperature in the presence of an external magnetic field. Our systematic heat capacity measurements utilizing a long-pulse and single-slope analysis technique allow us to detect a first-order phase transition in EuAg 4 Sb 2 at 7.5 K. The temperature-dependent electrical resistivity data also manifest two features associated with magnetic order. The magnetoresistance exhibits a broad hump due to a field-induced metamagnetic transition. Remarkably, the magnetoresistance keeps increasing without showing any tendency to saturate as the applied magnetic field increases, and it reaches ∼20 000% at 1.6 K and 60 T. At high magnetic fields, several magnetic quantum oscillations are observed, indicating a complex Fermi surface. A large negative magnetoresistance of about −55% is also observed near 𝑇 𝑁⁢1 . Moreover, the 𝐻−𝑇 phase diagram constructed using magnetization, heat capacity, and magnetotransport data indicates complex magnetic behavior in EuAg 4 Sb 2 .

36 MATERIALS SCIENCE↗