Results for “propulsion” — Page 36

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

STARC-ABL↗

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

STARC-ABL↗

NASA NTRS2019

Dynamic Analysis of the STARC-ABL Propulsion System

In the pursuit of Electrified Aircraft Propulsion (EAP), much of the attention is on the development of hybrid electric concept vehicles and their propulsion systems from a steady state performance perspective. While it is steady-state performance that largely determines the efficiency of civil air transports, engine operability and transient performance define constraints for the steady state design that impact efficiency and system viability. Neglecting dynamics and control technologies can result in an over-designed, sub optimal propulsion system or a concept that is not feasible. Thus, dynamic system studies were conducted on the propulsion system of the conceptual aircraft design known as the Single-aisle Turboelectric AiRCraft with Aft Boundary Layer propulsor (STARC-ABL). This paper describes the development of a controller to verify the baseline concept's feasibility from an operability perspective. Further, studies were conducted to identify excessive stability margin in the baseline design that could be traded for potential benefits in efficiency through an engine re design. This study revealed the potential to reduce the high pressure compressor (HPC) stall margin by 3%. Finally, a study was conducted to investigate the potential benefit of adding energy storage to the STARC-ABL concept that further improves operability and enables more gains in engine efficiency and performance. The energy storage provided an additional 0.5% stall margin can be removed from the HPC.

dynamic systems analysis↗

NASA NTRS2019

13kW Advanced Electric Propulsion Flight System Development and Qualification

The next phase of robotic and human deep space exploration missions requires high performance, high power solar electric propulsion systems for large-scale science missions and cargo transportation. Aerojet Rocketdyne's Advanced Electric Propulsion System (AEPS) program is completing development and qualification of a 13kW flight EP system to support NASA exploration. The first use of the AEPS is planned for the NASA Power & Propulsion Element, which is the first element of NASA's cis-lunar Gateway. The flight AEPS system includes a magnetically shielded long-life Hall thruster, power processing unit (PPU), and xenon flow controller (XFC). The Hall thruster, originally developed and demonstrated by NASA's Glenn Research Center and the Jet Propulsion Laboratory, operates at input powers up to 13.3kW while providing a specific impulse over 2600s at an input voltage of 600V. The power processor is designed to accommodate an input voltage range of 95 to 140V, consistent with operation beyond the orbit of Mars. The integrated system is continuously throttleable between 3 and 13.3kW. The program has completed testing of the Technology Development Units and is progressing into the Engineering Development Unit test phase and the final design phase to Critical Design Review (CDR). This paper will present the high power AEPS system capabilities, overall program and design status and the latest test results for the 13kW flight system development as well as the plans for the development and qualification effort of the EP string.

in-space propulsion↗

NASA NTRS2020

PACE Propulsion Subsystem Surge Analysis and Testing

Propulsion subsystem surge analysis and testing was performed at NASA Goddard Space Flight Center (GSFC) in order to analytically and experimentally determine the potential for damaging dynamic pressure events in the Plankton Aerosol Cloud and ocean Ecosystem (PACE) propulsion subsystem. Surge pressures occur when propellant flow is initiated following the actuation of an isolation valve separating an upstream high pressure fluid from a downstream low pressure manifold. By design, the PACE propulsion subsystem mitigates surge pressures using an orifice, or a cavitating venturi, placed upstream of each thruster bank isolation latch valve. Venturi sizing is a balancing act due to the competing performance goals of staying within the margins of an acceptable pressure loss and maintaining surge pressures below the proof pressure rating of the subsystem components. Subsystem pressure loss is dependent upon the venturi throat diameter and is higher for smaller venturi sizes. A venturi with a smaller throat diameter incurs an increased pressure loss through the orifice resulting in a reduced thruster inlet pressure and diminished thruster performance. The PACE propulsion subsystem surge analysis and testing supports system optimization, i.e. pressure drop minimization, while still meeting the surge pressure requirements to maximize overall system performance. In this paper a new approach to surge pressure analytical gauging is discussed, as well as its accuracy when compared to traditional surge testing campaign.

Space↗

NASA NTRSDate not supplied

Moderator Considerations for Space Nuclear Power and Propulsion Systems

Nuclear reactors have the potential to provide high energy density to enable sustainable surface power and advanced propulsion methods needed for human exploration activities at the moon and mars. Current mission planning is surveying different reactor types for space power and propulsion application. Of these reactor types, the use of a moderator within the reactor can enable reduced enrichment, reduce overall fuel loadings, and minimize the critical size of the reactor compared to unmoderated reference systems. This proceeding summarizes some moderator materials identified for space reactor applications: zirconium hydride, yttrium hydride, beryllium, and beryllium oxide, and the unique design considerations inherent to surface power and nuclear thermal propulsion reactor designs. It was found that there are four key considerations during the moderator selection and design process: nuclear properties, thermophysical & mechanical properties, manufacture & readiness, and environmental compatibility. Surface power reactors can benefit from moderators which minimize overall system mass and are capable of surviving high temperature irradiation environments for years with little degradation. Nuclear thermal propulsion reactors can benefit from moderators which are capable of retaining structural integrity under multiple burns while being exposed to a wide temperature range (40 < T < 500+ K). Moderator materials which exhibit good stability under irradiation and high temperature operation, minimize fuel pitch, and are high readiness are desirable for near term implementation.

nuclear thermal propulsion↗

NASA NTRS2022

Updated Assessment of Turboelectric Boundary Layer Ingestion Propulsion Applied to a Single-Aisle Commercial Transport

Recent advances in technology and a push for more environmentally friendly air transportation has led to interest in electrified aircraft propulsion (EAP). EAP encompasses many different propulsion system architectures which can also enable new, synergistic propulsion-airframe integration approaches. This report evaluates the combination of turboelectric EAP and fuselage boundary layer ingestion (BLI) propulsion in a concept called “STARC-ABL.” The predicted fuel consumption benefits of STARC-ABL are updated from a prior 2016 study with new mission requirements and analysis methodologies. Additionally, certification noise is added to the concept evaluation. To properly assess the impact of EAP, a new concept, “ST-ABL,” is developed for comparison which includes the fuselage BLI propulsor driven mechanically instead of by a turboelectric system. STARC-ABL is predicted to provide a 3.4% reduction in fuel consumption for a single-aisle class, 3500 nmi design mission and a 2.7% reduction for a 900 nmi mission, both relative to an advanced technology conventional aircraft. STARC-ABL is also predicted to have a Chapter 14 cumulative noise margin of 7 EPNdB. The non-EAP ST-ABL concept results in slightly higher fuel consumption and noise than STARC-ABL, indicating that the turboelectric system provides benefits over the mechanical drive approach to fuselage BLI. Areas for future research and evolution of the concept include assessing its applicability to other aircraft sizes, increasing the fidelity of BLI and electric component modeling, and investigating other EAP architecture options.

BLI↗

NASA NTRSDate not supplied

Overview of Fuel System Options for Nuclear Thermal Propulsion

An in-space propulsion technology, nuclear thermal propulsion (NTP) has the potential to enable faster interplanetary transit times compared to traditional chemical propulsion methods due to its capacity for high specific impulse (900+ s) and thrust (~10 – 100 klbf). Because of these performance attributes, NTP is currently one of several advanced propulsion technologies currently under consideration by the National Aeronautics and Space Administration (NASA) for future crewed Mars missions. The performance of NTP systems is directly contingent upon the development of a robust fuel form capable of withstanding high-power densities and operation in a hydrogen environment at temperatures in excess of 2500 K. This presentation will overview development needs for fuels in NTP systems, historic and current NTP fuel system options, and their remaining challenges prior to successful implementation.

nuclear thermal propulsion↗

NASA NTRSDate not supplied

NTAC Augmented Nuclear and Advanced Propulsion

Currently, there are two types of nuclear propulsion: Nuclear Thermal Propulsion (NTP) and Nuclear Electric Propulsion (NEP). Common to both types, a nuclear reactor generates heat energy to raise the temperature of propellant, or the generated heat energy is converted into electric power. The electricity generated powers propulsion systems, such as a Hall thruster, magnetoplasma dynamic (MPD) thruster, or variable specific impulse magnetoplasma rocket (VASIMR). Customarily, only the thermal energy output from nuclear reaction is considered for NTP and NEP systems. However, the nuclear fission reaction can also generate ~7 MeV of prompt gamma rays. Therefore, most designers of NTP and NEP systems incorporate safety features to shield against this radiation. An optimized design approach would be to integrate a Nuclear Thermionic Avalanche Cell (NTAC) within the NTP or NEP structure for converting this radiation energy into additional electric power, while also shielding gamma rays. Consequently, this study addresses several combinations of NTP and NEP structures with NTAC devices in order to achieve that goal.

NTAC↗

NASA NTRSDate not supplied

Development Of 12 Kw Hall Thrusters for Nasa Lunar Gateway Power And Propulsion Element

NASA is embarking on a new and exciting era of human exploration to the Moon and its vicinity. As part of the Artemis program, NASA is developing the lunar Gateway, an orbiting platform in Near Rectilinear Halo Orbit (NRHO) about the Moon. The first two elements of the Gateway will be launched in 2024 and will be transferred from a high Earth orbit to the NRHO via the use of Solar Electric Propulsion (SEP). The SEP system is located on the Power and Propulsion Element (PPE) which will provide up to 60 kW of power. Aerojet Rocketdyne is developing the 12 kW flight Hall thrusters to be used for transferring the PPE and the Habitat and Logistics Outpost (HALO) module to NRHO. Work is continuing on the development testing, and these results will be described in the paper. The project has also recently completed its critical design review and is transitioning to the fabrication of the three flight thrusters. The 12 kW Hall thrusters are being developed under the NASA Advanced Electric Propulsion System (AEPS) program. As part of the AEPS program, AR built two Engineering Test Unit (ETU) Hall thrusters based on the NASA HERMeS engine and conducted a series of tests to validate the design. One series of tests focused on environments and functional testing, while the other series was mainly focused on long duration test blocks. Results from these tests were used to compare with NASA data from the HERMeS thruster. The comparison of the test results showed no change to the critical performance and lifetime parameters, which enabled the next phase of the program to proceed. Currently testing is continuing on the Engineering Development Units (EDU) as part of the flight qualification activities. The successful completion of the CDR serves as the starting point for the flight thruster fabrication, which is now underway to support the launch of the Gateway modules in 2024. The development and qualification of the AEPS 12 kW Hall thrusters is proceeding well. As the program completes CDR and transitions into flight builds of the three 12 kW Hall thrusters that will be used to transfer the combined PPE and HALO stack to the NRHO, the results of the development testing are reviewed in this presentation, and a status of the program and future plans is provided. The launch of the two Gateway modules and the transfer of this large payload to cislunar orbit will mark a significant milestone in electric propulsion, as it will demonstrate the ability of SEP to transfer very large payloads over great distances. This establishes the precedent that could lead to cargo transfers from the Earth to the Moon or even to Mars using SEP.

Hall thrusters↗

NASA NTRSDate not supplied

Electrified Aircraft Propulsion Controls Hardware Testing

Electrified Aircraft Propulsion (EAP) systems hold potential for the reduction of aircraft fuel burn and emissions. To realize this potential for single-aisle aircraft, control technology challenges associated with EAP designs are increasing the demand for Hardware-In-the-Loop (HIL) studies that address the tightly coupled electrical powertrain and turbofan propulsion systems. Reconfigurable HIL testbeds enable the study of integrated supervisory control and control approaches that augment engine shaft torques to improve performance. This paper presents an overview of conceptual EAP controls architecture testing in two HIL testbeds. The NASA Electric Aircraft Testbed provides the ability for megawatt class electric powertrain testing for technology maturation. A 100 kilowatt testbed, the Hybrid Propulsion Emulation Rig, allows for rapid controls technology trade studies. In both testbeds, controls testing is performed by implementing the electrical power system in hardware while turbomachinery is emulated via electric machines that are commanded by a real-time model and controls. A novel scaling algorithm is applied to emulate the inertial loads of the turbomachinery that causes the electric machines to respond in a fashion similar to that of the full-scale propulsion system they represent. Results demonstrate desired control performance at both testbed scales for the conceptual EAP architecture.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Electrified Aircraft Propulsion Controls Hardware Testing

Electrified Aircraft Propulsion (EAP) systems hold potential for the reduction of aircraft fuel burn and emissions. To realize this potential for single-aisle aircraft, control technology challenges associated with EAP designs are increasing the demand for Hardware-In-the-Loop (HIL) studies that address the tightly coupled electrical powertrain and turbofan propulsion systems. Reconfigurable HIL testbeds enable the study of integrated supervisory control and control approaches that augment engine shaft torques to improve performance. This paper presents an overview of conceptual EAP controls architecture testing in two HIL testbeds. The NASA Electric Aircraft Testbed provides the ability for megawatt class electric powertrain testing for technology maturation. A 100 kilowatt testbed, the Hybrid Propulsion Emulation Rig, allows for rapid controls technology trade studies. In both testbeds, controls testing is performed by implementing the electrical power system in hardware while turbomachinery is emulated via electric machines that are commanded by a real-time model and controls. A novel scaling algorithm is applied to emulate the inertial loads of the turbomachinery that causes the electric machines to respond in a fashion similar to that of the full-scale propulsion system they represent. Results demonstrate desired control performance at both testbed scales for the conceptual EAP architecture.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

NASA’s Electric Aircraft Propulsion Research: Yesterday, Today and Tomorrow

NASA has been making investments since ~2015 in technologies related to electric aircraft propulsion. These investments span all-electric with our four passenger X-plane and electric vertical lift studies, to regional flight demonstrators and targeted technology maturation programs. These latter two areas are focused ultimately on reducing fuel burn and overall energy use in transport-class aircraft, with the goal of reducing carbon impact of aviation on our planet. Key technology contributions include such as electric machines, power electronics, cables/bus bars, fault management systems, controls and systems studies, and enabling materials. Today we are seeing the fundamental technology investments manifest themselves in flight demonstrations, that are aimed at impacting aircraft entering service 2035-2040 time range. These efforts have largely been aimed at megawatt scale technologies that can enable hybrid electric or mildly distributed airplane concepts. While these concepts offer benefits to regional and single isle aircraft it is thought that a more fully electrified propulsion system requiring greater than 10 MW of distributed power offers more possible pathways to configure the propulsion-airframe system to gain new efficiencies. A few examples of this are NASA’s SUSAN distributed electrofan concept and NASA University Leadership Initiatives such as CHEETA and IZEA that champion turbo-electric concepts. These concepts utilize combination of advanced technologies such as, fuel cells, power dense electronics and power dense electric machines and superconducting technologies. How much or which of these concepts will be adopted by industry is unclear, however another step function in electrifying aircraft propulsion is now on the horizon.

Electric Aircraft Propulsion↗

NASA NTRS2023

Combined 1-MW Solar Electric and Chemical Propulsion for Crewed Mars Missions

The current Moon to Mars Architecture defines functional capabilities that are essential to achieving NASA’s specific exploration goals and objectives. The transportation system goals and objectives or functional capabilities do not prescribe a solution, leaving an open tradespace to be explored. NASA is working to identify power and propulsion technologies that enable feasible transportation options for crewed missions to Mars. During NASA’s Strategic Analysis Cycle 2021 (SAC21), nuclear enabled spacecraft concepts were analyzed for moderate duration 850-day Earth-Mars roundtrip mission2. During SAC22, the transportation tradespace was expanded to understand the feasibility of using different propulsion systems for crewed Mars missions using a moderate duration reference mission as a comparison point. This paper explores the mission analysis performed for a conceptual MW-class hybrid Solar Electric Propulsion (SEP)-chemical propulsion system (SEP-Chem) spacecraft optimized for an 850-day crewed Mars mission for the 2039 opportunity.

SEP-Chem↗

NASA NTRS2023

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process. This process includes concept development and analysis, dynamic simulation, hardware-in-the-loop testing, full-scale testing, and so on. This effort is being revolutionized and indeed enabled by new digital tools that support increasing the technology readiness level throughout the maturation process. As part of this Digital Transformation, NASA has developed a suite of publicly available digital tools that facilitate the path from concept to implementation. This paper describes the NASA-developed tools and puts them in the context of control system development for hybrid electric aircraft propulsion. The three MATLAB®-based software packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid electric gas turbine engine powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper demonstrates through multiple examples how these tools have been used successfully in a variety of applications, including several of the early stages of hybrid electric gas turbine engine propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

hybrid electric propulsion↗

NASA NTRSDate not supplied

Statistical Wind-Tunnel Experimentation Advancements for eVTOL Aircraft Aero-Propulsive Model Development

Compared to many conventional aircraft, electric vertical takeoff and landing (eVTOL) vehicle designs present greater aero-propulsive complexity and many interacting factors requiring development of novel testing and model development strategies. This paper describes several advances in statistically-rigorous experiment design methods for wind-tunnel testing of eVTOL aircraft enabling accurate aero-propulsive model development. The techniques are applied to a subscale tilt-rotor eVTOL aircraft configuration built at NASA Langley Research Center that has 24 independent control effectors. The general testing approach, leveraging design of experiments and response surface methodology, is outlined and followed by a detailed description of the experiment design and modeling approach employed for different phases of the wind-tunnel testing. A new approach for gravitational tare modeling is developed and validated, which reduces the required wind-tunnel test time by nearly 50%. A mostly automated trim envelope determination approach is formulated to rapidly determine the aircraft flight envelope to inform transition testing for aero-propulsive model development. Efficient powered-airframe characterization tests are conducted using a nested I-optimal design approach formulated in previous simulation-based testing. The collective wind-tunnel testing approach facilitates rapid characterization of eVTOL aircraft configurations and produces accurate aero-propulsive models that can be used in flight dynamics simulations.

design of experiments↗

NASA NTRSDate not supplied

NASA Progress on the Development and Qualification of a 12-kW Hall-Effect, Solar Electric Propulsion Thruster

The National Aeronautics and Space Administration (NASA) continues to evolve the human exploration approach for beyond low-Earth orbit and in a manner involving international, academic, and industry partners. The center of this approach is NASA’s Gateway program that will establish a permanent human presence in lunar orbit for human cislunar science, operations, and lunar surface access to eventually land the next American astronauts on the south pole of the Moon. In support of the effort, NASA’s Space Technology Mission Directorate (STMD) began a project to increase the state of the art for the Hall-Effect Solar Electric Propulsion (SEP) technology. The resulting Advanced Electric Propulsion System (AEPS) project has developed a 12 kW Hall-effect thruster in support of the Gateway program. The project is managed by the NASA Glenn Research Center (GRC), supported by the NASA Jet Propulsion Laboratory (JPL) with development, qualification & flight hardware all supplied by L3 Harris Aerojet Rocketdyne (AR). Development of the 12-kW Hall thruster electric propulsion system began with maturation of the Hall Effect Rocket with Magnetic Shielding (HERMeS) Technology Demonstration Units (TDUs). The technology development was then transitioned to AR via the AEPS contract, which built and tested two Engineering Test Unit (ETU) thrusters and multiple critical components. The project transitioned to the production of the three flight thrusters and entered qualification testing at the component and thruster levels.

Electric Propulsion↗

NASA NTRSDate not supplied

NASA Progress on the Development and Qualification of a 12-kW Hall-Effect, Solar Electric Propulsion Thruster

The National Aeronautics and Space Administration (NASA) continues to evolve the human exploration approach for beyond low-Earth orbit and in a manner involving international, academic, and industry partners. The center of this approach is NASA’s Gateway program that will establish a permanent human presence in lunar orbit for human cislunar science, operations, and lunar surface access to eventually land the next American astronauts on the south pole of the Moon. In support of the effort, NASA’s Space Technology Mission Directorate (STMD) began a project to increase the state of the art for the Hall-Effect Solar Electric Propulsion (SEP) technology. The resulting Advanced Electric Propulsion System (AEPS) project has developed a 12 kW Hall-effect thruster in support of the Gateway program. The project is managed by the NASA Glenn Research Center (GRC), supported by the NASA Jet Propulsion Laboratory (JPL) with development, qualification & flight hardware all supplied by L3 Harris Aerojet Rocketdyne (AR). Development of the 12-kW Hall thruster electric propulsion system began with maturation of the Hall Effect Rocket with Magnetic Shielding (HERMeS) Technology Demonstration Units (TDUs). The technology development was then transitioned to AR via the AEPS contract, which built and tested two Engineering Test Unit (ETU) thrusters and multiple critical components. The project transitioned to the production of the three flight thrusters and entered qualification testing at the component and thruster levels.

Electric Propulsion↗