Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Investigation of Minimum Drag and Maximum Lift-drag Ratios of Several Wing-body Combinations Including a Cambered Triangular Wing at Low Reynolds Numbers and at Supersonic Speeds

Theoretical and experimental data for wing-body combinations with wings of triangular, arrow, and diamond plan form are presented for Mach numbers of 1.62, 1.93, and 2.41 and a Reynolds number range of 1.4 x 10 to the 6th power to 0.7 x 10 to the 6th power. Included are two each of triangular and arrow plan-form wings cambered for approximately uniform load at m = 1.62 and lift coefficients of 0.08 and 0.20. Liquid-film studies of the flow over the various configurations are also presented.

Brown, Clinton E↗
NASA NTRS1960

An Experimental Investigation of Boundary-Layer Control for Drag Reduction of a Swept-Wing Section at Low Speed and High Reynolds Numbers

An investigation of laminar boundary-layer control by suction for purposes of drag reduction at low speed and high Reynolds numbers has been conducted in the Ames 12-Foot Pressure Wind Tunnel. The model was a 72.96-inch-chord wing panel, swept back 30 deg., which was installed between end plates to approximate a wing of infinite span. The airfoil section employed was a modified NACA 66-012 in the streamwise direction. Tests were limited to controlling the flow over only the upper surface of the model. Seventeen individually controllable suction chambers were provided below the surface to induce flow through 93 spanwise slots in the surface between the 0.0052- and 0.97-chord stations. Tests were made at angles of attack of 0 deg., +/- 1.0 deg., +/- 1.5 deg., and -2.0 deg. for Reynolds numbers from approximately 1.5 x 10(exp 6) to 4.0 x 10(exp 6) per foot. In general, essentially full-chord laminar flow was obtained for all conditions with small suction quantities. Minimum profile-drag coefficients of about 0.0005 to 0.0006 were obtained for the slotted surface at maximum values of the Reynolds number; these values include the Power required to induce suction as an equivalent drag.

Gault, Donald E.↗
NASA NTRS1970

Solid state bistable power switch

Tin and copper provide high current and switching time capabilities for high-current resettable fuses. They show the best performance for trip current and degree of reliability, and have low coefficients of thermal expansion.

Bartko, J.↗
NASA NTRS1963

Wind-tunnel Measurement of Propeller Whirl-flutter Speeds and Static-stability Derivatives and Comparison with Theory

Results of an experimental investigation of propeller whirl flutter are presented for a model consisting of an isolated, rigid system of propeller and simulated power plant mounted with flexibility in pitch and yaw on a rigid sting. A range of propeller blade angles, restraint stiffnesses, and restraint damping coefficients was investigated for a system symmetrical i n pitch and yaw with a windmilling propeller. Measurements of the static-stability derivatives were also made by using a simple balance and were compared with two sets of theoretical derivatives. Whirl-flutter calculations were made with the theoretical and measured derivatives. Some limited results were obtained for the whirl flutter of the model mounted on a cantilever semispan wing. The measured whirl-flutter speeds and frequencies of the isolated model were in very good agreement with those predicted by calculations in which measured derivatives and viscous damping were used. This agreement was better than that obtained by using structural damping. Predicted whirl-flutter speeds for the isolated model were lower when theoretical stability derivatives were used than when measured derivatives were used. The theoretical and experimental static-stability derivatives exhibited the same trends, but in certain instances differed appreciably in magnitude. the measured whirl-flutter boundary for the one configuration considered.

PROPELLER↗
NASA NTRS1972

Effect of polarity of electric current on friction behavior of two gallium-lubricated tantalum slipring assemblies

Computer-processed data from low-speed (10 rpm) slipring experiments with two similar (but of opposite polarity) gallium-lubricated tantalum slipring assemblies (hemisphere against disk) carrying 50 amperes dc in vacuum (10 to the minus 9th power torr) showed that the slipring assembly with the anodic hemisphere had significantly lower peak-to-peak values and standard deviations of coefficient-of-friction samples (a measure of smoothness of operation) than the slipring assembly with the cathodic hemisphere. Similar data from an experiment with the same slipring assemblies running currentless showed more random differences in the frictional behavior between the two assemblies.

Przybyszewski, J.↗
NASA NTRS1974

Free-flight wind tunnel investigation of a four-engine sweptwing upper-surface blown transport configuration

The dynamic stability characteristics of a four-engine turbofan transport model having an upper-surface blown-jet flap have been investigated by means of the free-flight technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated through a range of lift coefficients from 3 to 8 with all four engines operating and with one outboard engine not operating. Static characteristics were investigated by conventional power-on force tests over the flight-test angle-of-attack range and through the stall.

Parlett, L. P.↗
NASA NTRS1977

Free-flight wind-tunnel investigation of a four-engine sweptwing upper-surface blown transport configuration

The dynamic stability and control characteristics of a four-engine turbofan transport model having an upper-surface blown jet flap were investigated by means of the free-flight technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated through a range of lift coefficients from 3 to 8 with all four engines operating and with one outboard engine not operating. Static characteristics were investigated by conventional power-on force tests over the flight-test angle-of-attack range and through the stall.

Parlett, L. P.↗
NASA NTRS1977

A note of expansions of functions of velocity in the two-body problem

Fourier expansions based on both the true anomaly and the mean anomaly are obtained for the functions of velocity in the two-body problem; the series of coefficients is written from classical formulae involving associated Legendre polynomials, Gegenbauer polynomials, or Bessel functions. The Fourier expansions are compared with the expansions in powers of eccentricity developed by Broucke (1974) through use of computerized Poisson series manipulation.

Kinoshita, H.↗
NASA NTRS1981

Two-dimensional aerodynamic characteristics of the NACA 0012 airfoil in the Langley 8 foot transonic pressure tunnel

Data are presented for lift coefficients from near zero through maximum values at Mach numbers from 0.30 to 0.86 and Reynolds numbers of 3.0 x 10 to the sixth power with transition fixed. A limited amount of data is presented near zero and maximum lift for a Reynolds number of 6.0 x 10 to the sixth power with transition fixed. In addition, transition free data is presented through the Mach number range from 0.30 to 0.86 for near zero lift and a Reynolds number of 3.0 x 10 to the sixth power.

Harris, C. D.↗
NASA NTRS1987

Plasma instability in the presence of negative ions

Ion density fluctuations are studied in a diffusion-controlled argon plasma containing, as a dilutant, two electron-attaching species, carbon dioxide and sulfur hexafluoride. It is found that the system becomes increasingly unstable as the concentration of the electron-attaching species is increased. Nonlinear mode-mode couplings have been identified and the coupling coefficients for these interactions have been computed. Turbulent fluctuations are observed to have pronounced three-dimensionality with distinct axial and azimuthal behaviors. The power spectra of these fluctuations are composed of many discrete modes. The importance of changes in the total discharge pressure is dependent on the electron-attachment cross section of the dilutant species. From these results it is shown that the ionization instability is probably responsible for the observed phenomenon.

Johnson, J. A., III↗
NASA NTRS1995

Features of the solar background velocity field

The scaling properties of a time series of Doppler images obtained in good visibility conditions are studied. A 28 cm vacuum telescope and a vacuum spectroheliograph in video spectra-spectroheliograph mode, are used. Sixty line-of-sight Doppler images of an area of the quiet sun are investigated. They were taken at 60 sec intervals over a one hour span and have a 2 arcsec resolution. After the removal of the five-minute oscillations, the time-spatial spectrum is calculated. To study the turbulence of photospheric flows, two scaling parameters in the spectra, are estimated: the exponent of the spatial part of the power spectrum, and the exponent governing the scaling of time correlations. The implied diffusive behavior is discussed. This includes the estimation of a diffusion coefficient and the type of diffusion involved.

Ruzmaikin, Alexander↗
NASA NTRS1998

A Comparison of Interactional Aerodynamics Methods for a Helicopter in Low Speed Flight

Recent advances in computing subsonic flow have been applied to helicopter configurations with various degrees of success. This paper is a comparison of two specific methods applied to a particularly challenging regime of helicopter flight, very low speeds, where the interaction of the rotor wake and the fuselage are most significant. Comparisons are made between different methods of predicting the interactional aerodynamics associated with a simple generic helicopter configuration. These comparisons are made using fuselage pressure data from a Mach-scaled powered model helicopter with a rotor diameter of approximately 3 meters. The data shown are for an advance ratio of 0.05 with a thrust coefficient of 0.0066. The results of this comparison show that in this type of complex flow both analytical techniques have regions where they are more accurate in matching the experimental data.

Berry, John D.↗
NASA NTRS1997

A Comparison of Interactional Aerodynamics Methods for a Helicopter in Low Speed Flight

Recent advances in computing subsonic flow have been applied to helicopter configurations with various degrees of success. This paper is a comparison of two specific methods applied to a particularly challenging regime of helicopter flight, very low speeds, where the interaction of the rotor wake and the fuselage are most significant. Comparisons are made between different methods of predicting the interactional aerodynamics associated with a simple generic helicopter configuration. These comparisons are made using fuselage pressure data from a Mach-scaled powered model helicopter with a rotor diameter of approximately 3 meters. The data shown are for an advance ratio of 0.05 with a thrust coefficient of 0.0066. The results of this comparison show that in this type of complex flow both analytical techniques have regions where they are more accurate in matching the experimental data.

Berry, John D.↗
NASA NTRS2005

Heat Pipe Reactor Dynamic Response Tests: SAFE-100 Reactor Core Prototype

The SAFE-I00a test article at the NASA Marshall Space Flight Center was used to simulate a variety of potential reactor transients; the SAFEl00a is a resistively heated, stainless-steel heat-pipe (HP)-reactor core segment, coupled to a gas-flow heat exchanger (HX). For these transients the core power was controlled by a point kinetics model with reactivity feedback based on core average temperature; the neutron generation time and the temperature feedback coefficient are provided as model inputs. This type of non-nuclear test is expected to provide reasonable approximation of reactor transient behavior because reactivity feedback is very simple in a compact fast reactor (simple, negative, and relatively monotonic temperature feedback, caused mostly by thermal expansion) and calculations show there are no significant reactivity effects associated with fluid in the HP (the worth of the entire inventory of Na in the core is .<el, so fluid movement and temperature changes will cause very minor effects). In previous SAFE-100 tests, the point kinetics model was based on core thermal expansion via deflection measurements. It was found that core deflection was a strung function of how the SAFE-100 modules were fabricated and assembled (in terms of straightness, gaps, and other tolerances). To remove the added variable of how this particular core expands as compared to a different concept, it was decided to use a temperature based feedback model (based on several thermocouples placed throughout the core).

Bragg-Sitton, Shannon M.↗
NASA NTRS2006

Heat Transfer and Fluid Dynamics Measurements in the Expansion Space of a Stirling Cycle Engine

The heater (or acceptor) of a Stirling engine, where most of the thermal energy is accepted into the engine by heat transfer, is the hottest part of the engine. Almost as hot is the adjacent expansion space of the engine. In the expansion space, the flow is oscillatory, impinging on a two-dimensional concavely-curved surface. Knowing the heat transfer on the inside surface of the engine head is critical to the engine design for efficiency and reliability. However, the flow in this region is not well understood and support is required to develop the CFD codes needed to design modern Stirling engines of high efficiency and power output. The present project is to experimentally investigate the flow and heat transfer in the heater head region. Flow fields and heat transfer coefficients are measured to characterize the oscillatory flow as well as to supply experimental validation for the CFD Stirling engine design codes. Presented also is a discussion of how these results might be used for heater head and acceptor region design calculations.

Jiang, Nan↗
NASA NTRS2015

Analysis of Advanced Thermoelectric Materials and Their Functional Limits

The world's demand for energy is increasing dramatically, but the best energy conversion systems operate at approximately 30% efficiency. One way to decrease energy loss is in the recovery of waste heat using thermoelectric (TE) generators. A TE generator is device that generates electricity by exploiting heat flow across a thermal gradient. The efficiency of a TE material for power generation and cooling is determined by the dimensionless Figure of Merit (ZT): ZT = S(exp. 2)sigmaT/κ: where S is the Seebeck coefficient, sigma is the electrical conductivity, T is the absolute temperature, and κ is the thermal conductivity. The parameters are not physically independent, but intrinsically coupled since they are a function of the transport properties of electrons. Traditional research on TE materials has focused on synthesizing bulk semiconductor-type materials that have low thermal conductivity and high electrical conductivity affording ZT values of 1. The optimization of the σ/κ ratio is difficult to achieve using current material formats, as these material constants are complementary. Recent areas of research are focusing on using nanostructural artifacts that introduce specific dislocations and boundary conditions that scatter the phonons. This disrupts the physical link between thermal (phonon) and electrical (electron) transport. The result is that κ is decreased without decreasing σ. These material formats give ZT values of up to 2 which represent approximately 18% energy gain from waste heat recovery. The next challenge in developing the next generation of TE materials with superior performance is to tailor the interconnected thermoelectric physical parameters of the material system. In order to approach this problem, the fundamental physics of each parameter S, sigma, and κ need to be physically understood in their context of electron/phonon interaction for the construction of new high ZT thermoelectric devices. Is it possible to overcome the physical limit imposed by of the effect of phonon lattice oscillation and energetic electrons towards thermal conductivity? Is the Seebeck coefficient, based on the difference in voltage over temperature gradient ( deltaV/deltaT), an intrinsic parameter of each material? All these parameters were manipulated using nano-bridge and twin-lattice structural concepts at the NASA Langley Research Center. This talk will review the current trend of TE research to optimize the ZT and discuss about new approaches on increasing ZT within functional limits of each parameter.

Kim, Hyun Jung↗