Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic work”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

In situ monitoring of dislocation, twinning, and detwinning modes in an extruded magnesium alloy under cyclic loading conditions

This work investigates the microscopic deformation mechanisms of an extruded, precipitation-strengthened AZ80 magnesium (Mg) alloy subjected to strain-controlled low-cycle fatigue using in situ neutron diffraction measurements. Results demonstrate that the plastic deformation during cyclic loading is dominated by the alternating {10.2} extension twinning and detwinning mechanisms. The observed deformation mode is strongly texture and precipitate dependent. For the initial texture, the tested material has two major texture components which result in the occurrence of extension twinning during both compression and reverse tension in the first two cycles. The prolonged detwinning process in the following cycles is proposed to relieve the shear stress field of {00.2} grains, leading to the disappearance of twinning. The precipitation strengthening results in an increase of the critical resolved shear stress (CRSS) by similar to 33 MPa for the extension twinning in this AZ80 alloy. Here, the synergistic effects of the initial texture, precipitation strengthening, and load sharing of various grain families and phases contribute to the complicated evolution of dominant deformation mechanisms, among which elevated dislocation activities are believed to be responsible for the relatively poor low-cycle-fatigue lifetime when compared to other Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Solventless, Ambient-Pressure Production of Bio-Based Lactones Over Earth-Abundant, Mixed Metal Oxide Catalysts for Circular Polyesters

Transitioning to a circular plastics economy will require use of renewable feedstocks, energy-efficient processes, and closed-loop recyclable polymers, such as polyesters. A key challenge lies in sustainably sourcing monomers used to make recyclable polyesters. This work presents a catalytic platform utilizing earth-abundant Cu(x)Ca(1-x)O mixed metal oxides for the oxidative dehydrocyclization of bio-based diols to lactones, which are advantaged for energy-efficient ring-opening polymerization. Operating below 200 degrees C, at ambient pressure, and without solvent, the process uses air as the sole oxidant, achieving high yields of lactones across a broad substrate scope of C4-8 diols in the liquid phase. The oxidative dehydrocyclization reaction is thermodynamically downhill due to water formation and energy-efficient compared to incumbent, non-redox pathways utilized in fossil carbon-based industrial processes for lactone production. Mechanistic studies reveal facile redox cycling of Cu2+-O(Ca2+)-Cu2+ interfacial sites unique to the developed catalyst. Techno-economic analysis and life cycle assessment estimate 40% lower energy demand and 15% lower GHG intensity per mass of butyrolactone produced compared to the fossil carbon-based route. Liquid-phase oxidative dehydrocyclization offers a promising approach for scalable lactone production from renewable, bio-based diols to enable circular polyesters.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Competition between roughness and strength for scale-dependent surfaces

Rocks famously have scale-dependent strength, yet the actual dependence is notoriously hard to measure or incorporate into any theoretical framework. Natural rough surfaces present an opportunity to solve the problem. Surfaces sliding in shear evolve as protrusions collide. These asperities can deform or break, thus creating a new surface shape. In particular, natural surfaces have roughness at all scales as well as scale-dependent strength. Based on a scaling analysis, we have previously suggested that the scale-dependent aspect ratio of steady-state surfaces should be proportional to the scale-dependent shear strain at yield. If true, scale-dependent strength could easily be inferred from natural surfaces. Thus, moving beyond the scaling argument to a rigorous treatment of scale-dependent strength for multiscale rough surfaces in shear is important. However, analytic frameworks for analyzing multiscale problems are challenging, as conventional continuum mechanics typically involves a single value for a material property across scales. Here, in this work, we build on the formalism of Persson (2001) that presents a method to compute contact area for rough surfaces with a prescribed topographic spectrum using a stochastic differential equation. The Persson formalism allows for plastic yield under normal loading of otherwise elastic materials and leaves open the possibility of scale-dependent yield stress. In this study, we pursue this route to develop a theory and numerical results for the yielding of a rough, elastoplastic surface with scale-dependent yield stress. Here, we examine surfaces for which the power spectrum of the topography 𝐶 and yield stress 𝑌 follow power laws as a function of scale 𝜆, such that 𝐶∼𝜆 −𝑚 and 𝑌∼𝜆 −𝑛 , respectively. In this formal treatment of the problem, we focus on surfaces in contact and the resulting yield and do not impose shear. Numerical solutions show that the deviation from the elastic scaling solution is bounded as expected by the prior 1D heuristic scaling argument that anticipates the Hurst exponent as 1−𝑛. We also show that the plasticity is expected to erode the contacts if 𝑚 is lower than 𝑛−3, which corresponds to a Hurst exponent lower than 1−𝑛/2. This result is rigorously sound for 2D, i.e., realistic surfaces, and quantitatively different than the prior scaling argument. The theory now permits a correspondingly quantitative approach to interpreting natural surfaces.

elasticity↗
NASA NTRS1993

The p-version of the finite element method in incremental elasto-plastic analysis

Whereas the higher-order versions of the finite elements method (the p- and hp-version) are fairly well established as highly efficient methods for monitoring and controlling the discretization error in linear problems, little has been done to exploit their benefits in elasto-plastic structural analysis. Aspects of incremental elasto-plastic finite element analysis which are particularly amenable to improvements by the p-version is discussed. These theoretical considerations are supported by several numerical experiments. First, an example for which an analytical solution is available is studied. It is demonstrated that the p-version performs very well even in cycles of elasto-plastic loading and unloading, not only as compared to the traditional h-version but also in respect to the exact solution. Finally, an example of considerable practical importance - the analysis of a cold-worked lug - is presented which demonstrates how the modeling tools offered by higher-order finite element techniques can contribute to an improved approximation of practical problems.

Holzer, Stefan M.↗
NASA NTRS1981

Heat Pipe Technology

The heat pipe, a sealed chamber whose walls are lined with a "wick," a thin capillary network containing a working fluid in liquid form was developed for a heat distribution system for non-rotating satellites. Use of the heat pipe provides a continuous heat transfer mechanism. "Heat tubes" that improve temperature control in plastics manufacturing equipment incorporated the heat pipe technology. James M. Stewart, an independent consultant, patented the heat tubes he developed and granted a license to Kona Corporation. The Kona Nozzle for heaterless injection molding gets heat for its operation from an external source and has no internal heating bands, reducing machine maintenance and also eliminating electrical hazards associated with heater bands. The nozzles are used by Eastman Kodak, Bic Pen Corporation, Polaroid, Tupperware, Ford Motor Company, RCA, and Western Electric in the molding of their products.

Source record↗
NASA NTRS2008

Modeling the Non-Linear Response of Fiber-Reinforced Laminates Using a Combined Damage/Plasticity Model

The present work is concerned with modeling the non-linear response of fiber reinforced polymer laminates. Recent experimental data suggests that the non-linearity is not only caused by matrix cracking but also by matrix plasticity due to shear stresses. To capture the effects of those two mechanisms, a model combining a plasticity formulation with continuum damage has been developed to simulate the non-linear response of laminates under plane stress states. The model is used to compare the predicted behavior of various laminate lay-ups to experimental data from the literature by looking at the degradation of axial modulus and Poisson s ratio of the laminates. The influence of residual curing stresses and in-situ effect on the predicted response is also investigated. It is shown that predictions of the combined damage/plasticity model, in general, correlate well with the experimental data. The test data shows that there are two different mechanisms that can have opposite effects on the degradation of the laminate Poisson s ratio which is captured correctly by the damage/plasticity model. Residual curing stresses are found to have a minor influence on the predicted response for the cases considered here. Some open questions remain regarding the prediction of damage onset.

Schuecker, Clara↗
NASA NTRS2016

Design of Superconducting Gravity Gradiometer Cryogenic System for Mars Mission

Measurement of a planet's gravity field provides fundamental information about the planet's mass properties. The static gravity field reveals information about the internal structure of the planet, including crustal density variations that provide information on the planet's geological history and evolution. The time variations of gravity result from the movement of mass inside the planet, on the surface, and in the atmosphere. NASA is interested in a Superconducting Gravity Gradiometer (SGG) with which to measure the gravity field of a planet from orbit. An SGG instrument is under development with the NASA PICASSO program, which will be able to resolve the Mars static gravity field to degree 200 in spherical harmonics, and the time-varying field on a monthly basis to degree 20 from a 255 x 320 km orbit. The SGG has a precision two orders of magnitude better than the electrostatic gravity gradiometer that was used on the ESA's GOCE mission. The SGG operates at the superconducting temperature lower than 6 K. This study developed a cryogenic thermal system to maintain the SGG at the design temperature in Mars orbit. The system includes fixed radiation shields, a low thermal conductivity support structure and a two-stage cryocooler. The fixed radiation shields use double aluminized polyimide to emit heat from the warm spacecraft into the deep space. The support structure uses carbon fiber reinforced plastic, which has low thermal conductivity at cryogenic temperature and very high stress. The low vibration cryocooler has two stages, of which the high temperature stage operates at 65 K and the low temperature stage works at 6 K, and the heat rejection radiator works at 300 K. The study also designed a second option with a 4-K adiabatic demagnetization refrigerator (ADR) and two-stage 10-K turbo-Brayton cooler.

Gradiometer↗
NASA NTRS2016

Design of Superconducting Gravity Gradiometer Cryogenic System for Mars Mission

Measurement of a planets gravity field provides fundamental information about the planets mass properties. The static gravity field reveals information about the internal structure of the planet, including crustal density variations that provide information on the planets geological history and evolution. The time variations of gravity result from the movement of mass inside the planet, on the surface, and in the atmosphere. NASA is interested in a Superconducting Gravity Gradiometer (SGG) with which to measure the gravity field of a planet from orbit. An SGG instrument is under development with the NASA PICASSO program, which will be able to resolve the Mars static gravity field to degree 200 in spherical harmonics, and the time-varying field on a monthly basis to degree 20 from a 255 x 320 km orbit. The SGG has a precision two orders of magnitude better than the electrostatic gravity gradiometer that was used on the ESAs GOCE mission. The SGG operates at the superconducting temperature lower than 6 K. This study developed a cryogenic thermal system to maintain the SGG at the design temperature in Mars orbit. The system includes fixed radiation shields, a low thermal conductivity support structure and a two-stage cryocooler. The fixed radiation shields use double aluminized polyimide to emit heat from the warm spacecraft into the deep space. The support structure uses carbon fiber reinforced plastic, which has low thermal conductivity at cryogenic temperature and very high stress. The low vibration cryocooler has two stages, of which the high temperature stage operates at 65 K and the low temperature stage works at 6 K, and the heat rejection radiator works at 300 K. The study also designed a second option with a 4-K adiabatic demagnetization refrigerator (ADR) and two-stage 10-K turbo-Brayton cooler.

Li, X.↗
DOE OSTI2025

Surface smoothing for laser powder-bed Ti-6Al-4V by a transient liquid phase

Surface roughness is the primary driver of fatigue for additively manufactured metals. To address surface roughness, this work introduces a new method to smooth features beyond line-of-sight without material removal. The method applies a coating that triggers local surface remelting by activating a eutectic reaction during heat treatment. The associated liquid phase then wets and isothermally solidifies into a smoother surface. For Ti-6Al-4V fabricated with laser powder bed fusion, samples with and without TLP smoothing (using a Cu coating) were characterized with a suite of techniques, including mechanical testing, electron backscatter diffraction, synchrotron X-ray tomography, and fractography. TLP smoothing reduced surface roughness by 80% and amplified compressive residual stress at the surface by about 50%. With statistically equivalent virtual microstructures, crystal plasticity scrutinized the roles of phases, porosity, and surface roughness. Although the tensile strain-to-failure was reduced to 1% strain, the TLP smoothing process increased high-cycle fatigue strength by about 20% compared to control samples, pointing to future opportunities to optimize the new process through various coating compositions and heat treatment schedules. Overall, this work establishes a new paradigm for treating surfaces of materials for smoothness and compressive residual stress.

Additive manufacturing↗
DOE OSTI2025

Development of Predictive Model for Accurate Rupture Time from Multi-Axial Creep in Alloy 709 with Physics-Based Simulations

A physics-based model is developed to predict multiaxial creep behavior in Alloy 709 (A709), an advanced austenitic stainless steel intended for high-temperature applications such as Sodium Fast Reactors (SFRs). Compared to conventional stainless steels like 316H, A709 offers superior high-temperature performance; however, comprehensive data on its multiaxial creep response remain limited. To address this gap, a crystal plasticity finite element (CPFE) framework is used to simulate the deformation and failure mechanisms of A709 under multiaxial loading conditions. The model incorporates an extended Hu-Cocks dislocation creep formulation that accounts for precipitation effects, along with the Sham–Needleman model to capture grain boundary cavitation-driven failure. These advanced constitutive models enable a detailed understanding of the interplay between microstructural evolution and macroscopic creep response. Furthermore, the study evaluates the predictive accuracy of various effective stress measures in estimating creep rupture life, leveraging simulated multiaxial creep data. The findings provide critical insights into the applicability of different stress measures for engineering design and life prediction of A709 components operating under complex loading conditions. This work contributes to improving the reliability of high-temperature structural components by advancing predictive modeling capabilities for advanced austenitic steels.

Alloy 709↗
NASA NTRS1987

Effect of heat treatment on the fracture behaviour of directionally solidified (gamma/gamma-prime)-alpha alloy

An investigation is conducted into the influence of various heat treatments on the work of fracture and its relation to microstructure for a directionally solidified Ni-33Mo-5.7Al (wt pct) (gamma/gamma-prime)-alpha alloy. The jagged crack propagation observed is due to delamination of the ligaments and associated plastic deformation. Fracture behavior is examined with respect to alloy microstructures and load-deflection curves. The four heat-treatment conditions considered are: (1) as-directionally solidified, (2) solutionized, (3) directionally solidified and thermally cycled, and (4) solutionized and thermally cycled.

Sriramamurthy, A. M.↗
NASA NTRS2013

Testing and Analysis Validation of a Metallic Repair Applied to a PRSEUS Tension Panel

A design and analysis of a repair concept applicable to a stiffened composite panel based on the Pultruded Rod Stitched Efficient Unitized Structure was recently completed. The damage scenario considered was a midbay-to-midbay saw-cut with a severed stiffener, flange and skin. Advanced modeling techniques such as mesh-independent definition of compliant fasteners and elastic-plastic material properties for metal parts were utilized in the finite element analysis supporting the design effort. A bolted metallic repair was selected so that it could be easily applied in the operational environment. The present work describes results obtained from a tension panel test conducted to validate both the repair concept and finite element analysis techniques used in the design effort. The test proved that the proposed repair concept is capable of sustaining load levels that are higher than those resulting from the current working stress allowables. This conclusion enables upward revision of the stress allowables that had been kept at an overly-conservative level due to concerns associated with repairability of the panels. Correlation of test data with finite element analysis results is also presented and assessed.

Przekop, Adam↗
NASA NTRS2010

Mineralogy of SNC Meteorite EET79001 by Simultaneous Fitting of Moessbauer Backscatter Spectra

We have acquired M ssbauer spectra for SNC meteorite EET79001 with a MIMOS II backscatter M ssbauer spectrometer [1] similar to those now operating on Mars as part of the Mars Exploration Rover (MER) missions. We are working to compare the Fe mineralogical composition of martian meteorites with in-situ measurements on Mars. Our samples were hand picked from the >1 mm size fraction of saw fines on the basis of lithology, color, and grain size (Table 1). The chips were individually analyzed at approx.300K by placing them on a piece of plastic that was in turn supported by the contact ring of the instrument (oriented vertically). Tungsten foil was used to mask certain areas from analysis. As shown in Figure 1, a variety of spectra was obtained, each resulting from different relative contributions of the Fe-bearing minerals present in the sample. Because the nine samples are reasonably mixtures of the same Fe-bearing phases in variable proportions, the nine spectra were fit simultaneously (simfit) with a common model, adjusting parameters to a single minimum chi-squared convergence criterion [2]. The starting point for the fitting model and values of hyperfine parameters was the work of Solberg and Burns [3], who identified olivine, pyroxene, and ferrous glass as major, and ilmenite and a ferric phase as minor (<5%), Fe-bearing phases in EET79001.

Morris, Richard V.↗
DOE OSTI2025

Anion and Cation Size Effects on Viscoelasticity and Ion Transport of Imine Vitrimer Electrolytes

Vitrimers are a subclass of covalent adaptable networks where bond exchange occurs without breaking, thereby offering polymer materials with enhanced mechanical strength, thermal stability, and reprocessability compared to conventional electrolytes. Despite recent progress, we lack a complete understanding of the role of ions in controlling the physical and chemical properties of vitrimers. In this work, we study how different salts affect the viscoelasticity, morphology, and ionic conductivity of imine vitrimers. Our results show that addition of salt decreases relaxation times at elevated temperatures due to the catalytic effect of the cations, with smaller cations leading to faster relaxation. However, the activation energy for terminal relaxation increases with smaller cation size. This apparent discrepancy is attributed to the complex interplay among bond exchange kinetics, chain diffusion, and salt dissociation. Anions act as plasticizers by reducing the shear modulus, except lithium bromide. Ionic conductivity increases with larger anions due to smaller salt dissociation energies, whereas the cation type has a minor impact as polymer segmental dynamics dominate ionic transport. Imine-based vitrimers are reprocessable and recyclable, maintaining original mechanical properties and ionic conductivity after recovery. Mixed salt vitrimers exhibited tunable viscoelasticity and ionic conductivity intermediate to the analogous pure salt systems. Altogether, this work highlights the role of salt in the dynamic and conductive properties of imine vitrimers.

Anions↗
DOE OSTI2022

Micromechanical Fields Associated with Irregular Deformation Twins in Magnesium

Understanding and controlling the development of deformation twins is paramount for engineering strong and stable hexagonal close-packed (HCP) Mg alloys. Actual twins are often irregular in boundary morphology and twin crystallography, deviating from the classical picture commonly used in theory and simulation. In this work, the elastic strains and stresses around irregular twins are examined both experimentally and computationally to gain insight into how twins develop and the microstructural features that influence their development. A nanoprecession electron diffraction (N-PED) technique is used to measure the elastic strains within and around a $\left\{ {10\overline{1}2} \right\}$ tensile twin in AZ31B Mg alloy with nm scale resolution. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) crystal plasticity model of the same sub-grain and irregular twin structure is employed to understand and interpret the measured elastic strain fields. The calculations predict spatially resolved elastic strain fields in good agreement with the measurement, as well as all the stress components and the dislocation density fields generated by the twin, which are not easily obtainable from the experiment. The model calculations find that neighboring twins, several twin thicknesses apart, have little influence on the twin-tip micromechanical fields. Furthermore, this work reveals that irregularity in the twin-tip shape has a negligible effect on the development of the elastic strains around and inside the twin. Importantly, the major contributor to these micromechanical fields is the alignment of the twinning shear direction with the twin boundary.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A framework and tool for designing cost-effective, resilient, and circular net-zero supply chains under uncertainty with an application to multilayer plastic films

While 55% of Fortune 500 companies have committed to achieving net-zero emissions and/or zero-waste operations by 2035, only 2% are currently on track, revealing a critical gap between ambition and action. Designing supply chains that reduce both emissions and waste is a complex non-intuitive, multi-objective challenge, compounded by the high costs of new technologies and the need for resilient, profitable solutions. This paper aims to address this challenge by presenting a generic framework and multi-objective optimization formulation for designing cost-effective, circular, and resilient supply chains under uncertainty, implemented through a user-friendly decision-support tool with intuitive data visualization capabilities, enabling communication of results to both technical and non-technical stakeholders. We demonstrate the application of this framework in the context of multilayer plastic films (barrier films), which are widely used in food packaging and composite materials. The model quantifies trade-offs across three objectives: minimizing global warming potential, maximizing circularity, and minimizing cost. A key contribution of this work is the explicit modeling of technological resilience, the ability of supply chains to maintain function under disruption. In the cost-minimization case, the resilience constraint makes the design approximately three times more expensive in the short-term metric, but shifts the system from relying on a single recovery pathway to a portfolio of four recovery pathways, improving the robustness of the optimization solution under uncertainty. Lastly, we introduce TranZero, a decision-support tool that integrates material flow analysis, hotspot identification, and optimization-based scenario planning to support net-zero and circularity decisions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

The influence of temperature on the strain-hardening behavior of Fe-22/25/28Mn-3Al-3Si TRIP/TWIP steels

In this work, the influence of temperature and stacking fault energy (SFE) on the strain-hardening behavior and critical resolved shear stress for twinning was investigated for three Fe–22/25/28Mn–3Al–3Si wt.% transformation- and twinning-induced plasticity (TRIP/TWIP) steels. The SFEs were calculated by two different methods, density functional theory and statistical thermodynamic modeling. The dislocation structure, observed at low levels of plastic deformation, transitions from “planar” to “wavy” dislocation glide with an increase in temperature, Mn content, and/or SFE. The change in dislocation glide mechanisms from planar to wavy reduces the strain hardening rate, in part due to fewer planar obstacles and greater cross slip activity. Additionally, the alloys exhibit a large decrease in strength and ductility with increasing temperature from 25 to 200 °C, attributed to a substantial reduction in the thermally activated component of the flow stress, predominate suppression of TRIP and TWIP, and a significant increase in the critical resolved shear stress for mechanical twinning. Interestingly, the increase in SFE with temperature had a rather minor influence on the critical resolved shear stress for mechanical twinning, and other temperature dependent factors which likely play a more dominant role are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evaluation of thermodynamic closure models for partially reacted two-phase mixture of condensed phase explosives

One of the key fundamental issues that is crucial in the continuum modeling of reactive flow phenomena is the thermodynamically consistent description of reaction mixture properties. To define the mixture properties, thermodynamic closure rules that relate the properties of the individual reaction components to the mixture properties are required. In the context of reactive two-phase modeling approaches, various strategies to define the thermodynamic closures have been adopted such as pressure temperature (PT) equilibrium between the individual reaction components, pressure (specific) volume (PV) equilibrium, etc. The choice of closure rules determines the relative distribution of specific volume and energy across the reaction components that comprise the mixture. Therefore, depending on the choice of the closure, the mixture thermodynamic behavior can vary. The present work examines the effect of different closure approaches on the thermodynamic properties of the reaction mixture. The analysis is performed for a condensed phase HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) based plastic bonded explosive (PBX) 9501 explosive using four different thermodynamic closures, viz., PT equilibrium, PV equilibrium, volume temperature (VT) equilibrium, and pressure (P) equilibrium with reactants on an isentrope. Furthermore, the relative variations in the thermodynamic properties of the mixture are analyzed and compared under both compression and expansion loading regimes. It is shown that out of the four closure models, only PT equilibrium and P equilibrium closures lead to a thermodynamically accurate description of the mixture under both compression and expansion.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗