Results for “particle applications” — Page 36

NASA NTRS1992

Removing Undesired Fine Powder From Silicon Reactor

Fluidized-bed reactor produces highly pure polycrystalline silicon particles with diameters approximately greater than 400 micrometers. Operates by pyrolysis of silane in reaction zone, which is bed of silicon seed particles fluidized by flow of silane and carrier gas. Above reaction zone, gas mixture flows rapidly enough to entrain silicon powders, but not larger seed and product particles. Entrained particles swept out of reactor. Applicable to other processes such as production of fine metal and ceramic powders where control of sizes of product needed.

Flagella, Robert N.↗

NASA NTRS1992

Issues/considerations and performance prediction of LEO protective coatings

Organic materials can be used in low earth orbit for long periods only if they are made to be durable to atomic oxygen in addition to the threats of ultraviolet radiation, micrometeoroid and debris impact, thermal cycling, and charged particle radiation. In many materials applications, it is more cost-effective to utilize atomic oxygen protective coatings over materials which are vulnerable to attack by atomic oxygen rather than developing alternative materials which are inherently durable. Many metal and metal oxide coatings have been shown to be potentially suitable for long term protection of organic polymers in low earth orbit. The protection afforded by thin film coatings on polymeric substrates is highly dependent on the completeness of coverage of the coating. Thus, the prime indicator of durability is the size and abundance of pin windows and scratches in the protective coating. Such defects depend on the deposition technique, smoothness of the surface to be protected, and presence of particulate contaminants. Issues and considerations relevant to substrate preparation, deposition of protective coatings, ground laboratory simulation and evaluation of threats in low earth orbit to protective materials, results of in-space tests, and the use of Monte Carlo modeling techniques to predict in-space durability are presented in graphic form.

Banks, Bruce A.↗

NASA NTRS2004

Cross-Stream PIV Measurements of Jets With Internal Lobed Mixers

With emphasis being placed on enhanced mixing of jet plumes for noise reduction and on predictions of jet noise based upon turbulent kinetic energy, unsteady measurements of jet plumes are a very important part of jet noise studies. Given that hot flows are of most practical interest, optical techniques such as Particle Image Velocimetry (PIV) are applicable. When the flow has strong azimuthal features, such as those generated by chevrons or lobed mixers, traditional PIV, which aligns the measurement plane parallel to the dominant flow direction is very inefficient, requiring many planes of data to be acquired and stacked up to produce the desired flow cross-sections. This paper presents PIV data acquired in a plane normal to the jet axis, directly measuring the cross-stream gradients and features of an internally mixed nozzle operating at aircraft engine flow conditions. These nozzle systems included variations in lobed mixer penetration, lobe count, lobe scalloping, and nozzle length. Several cases validating the accuracy of the PIV data are examined along with examples of its use in answering questions about the jet noise generation processes in these nozzles. Of most interest is the relationship of low frequency aft-directed noise with turbulence kinetic energy and mean velocity.

Bridges, James↗

NASA NTRS2005

The Future of Bio-technology

Hosts of technologies, most notably in electronics, have been on the path of miniaturization for decades and in 2005 they have crossed the threshold of the nano-scale. Crossing the nano-scale threshold is a milestone in miniaturization, setting impressive new standards for component-packing densities. It also brings technology to a scale at which quantum effects and fault tolerance play significant roles and approaches the feasible physical limit form many conventional "top-down" manufacturing methods. I will suggest that the most formidable manufacturing problems in nanotechnology will be overcome and major breakthroughs will occur in a host of technologies, when nanotechnology converges with bio-technology; i.e. I will argue that the future of bio-technology is in nanotechnology. In 2005, methods in molecular biology, microscopy, bioinformatics, biochemistry, and genetic engineering have focused considerable attention on the nano-scale. On this scale, biology is a kind of recursive chemistry in which molecular recognition, self-assembly, self-organization and self-referencing context-control lead to the emergence of the complexity of structures and processes that are fundamental to all life forms. While we are still far from understanding this complexity, we are on the threshold of being able to use at least some of these biological properties for .technology. I will discuss the use of biomolecules, such as DNA, RNA, and proteins as "tools" for the bio-technologist of the future. More specifically, I will present in some detail an example of how we are using a genetically engineered 60-kDa protein (HSP60) from an organism living in near boiling sulfuric acid to build nano-scale templates for arranging metallic nanoparticles. These "extremophile" HSP60s self-assemble into robust double-ring structures called "chaperonins," which further assemble into filaments and arrays with nanometer accuracy. I will discuss our efforts to use chaperonins to organize quantum dots, electronic and magnetic nano-particles for electronic and photonic applications.

Trent, Jonathan↗

NASA NTRS2017

Measurements of Turbulent Convection Speeds in Multistream Jets Using Time-Resolved PIV

Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

Jet↗

NASA NTRS2017

Measurements of Turbulence Convection Speeds in Multistream Jets Using Time-Resolved PIV

Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

Convection Speed↗

NASA NTRS2018

Inkjet Printing of Conductive Carbon Nanotubes

Systems and methods for forming conductive materials. The conductive materials can be applied using a printer in single or multiple passes onto a substrate. The conductive materials are composed of electrical conductors such as carbon nanotubes (including functionalized carbon nanotubes and metal-coated carbon nanotubes), grapheme, a polycyclic aromatic hydrocarbon (e.g. pentacene and bisperipentacene), metal nanoparticles, an inherently conductive polymer (ICP), and combinations thereof. Once the conductive materials are applied, the materials are dried and sintered to form adherent conductive materials on the substrate. The adherent conductive materials can be used in applications such as damage detection, particle removal, and smart coating systems.

Roberson, Luke B.↗

NASA NTRS2020

Measurements of Turbulent Convection Speeds in Multistream Jets Using Time-Resolved PIV

Convection speeds of turbulent velocities in jets, including multi-stream jets with and without flight stream, were measured using an innovative application of time-resolved particle image velocimetry. The paper describes the unique instrumentation and data analysis that allows the measurement to be made. Extensive data is shown that relates convection speed, mean velocity, and turbulent velocities for multiple jet cases. These data support the overall observation that the local turbulent convection speed is roughly that of the local mean velocity, biased by the relative intensity of turbulence.

Particle Image Velocimetry; Convective Velocity; J↗

DOE OSTI2021

Polyamine phosphorus dendrimer materials for carbon dioxide capture

The present disclosure provides novel solid sorbents synthesized by the reaction of polyamines with polyaldehyde phosphorous dendrimer (P-dendrimer) compounds. The sorbents are highly stable and exhibit rapid reaction kinetics with carbon dioxide, making the sorbents applicable for carbon capture, and can be easily regenerated for further use. The material is stable to aqueous and organic media, as well as strong acid and bases. The sorbent maintains full capacity over extended use. The material can be used for CO2 capture from pure CO2 streams, mixed gas streams, simulated flue gas, and ambient air. Additionally, the material can be adhered to surfaces for reversible CO2 capture applications outside of bulk particle-based processes.

Thompson, III, Samuel John↗

DOE OSTI2025

Enhancing ICARUS and REDTOP Software and Hardware: Event Generator Interface Development and Calorimeter Tile Prototype

ICARUS (Imaging Cosmic And Rare Underground Signals) is a liquid argon time projection chamber (LArTPC) detector that pursues the sterile neutrino, which relies on accurate simulations of neutrino-argon interactions. REDTOP (Rare Eta Decays To Observe new Physics) is a proposed low-energy, high-intensity meson factory designed to explore rare $\eta$/$\eta'$ meson decays and probe physics beyond the Standard Model. As a next-generation experiment, this requires both accurate simulations and innovative detector technologies. This project contributes to both ICARUS, from a simulation perspective, and REDTOP, from both a simulation and detection perspective, through the event generation of lepton-nucleon interactions and the physical enhancement of the calorimeter technology within the REDTOP detector. We developed an interface between ACHILLES (A CHIcago Land Lepton Event Simulator), a theory-driven lepton-level event generator, and GENIE, a robust event generator framework used for neutrino physics. By incorporating the precise theoretical cross-section calculations of ACHILLES into the experimental realism of GENIE, the interface allows for improved accuracy of neutrino-nucleon simulations, which can be adapted for the proton beam specifications of the REDTOP meson factory as well as for the ICARUS experiment. In parallel, we developed an improved prototype for the ADRIANO2 (A Dual Readout Integrally Active Non-segmented Option) dual-readout calorimeter tiles for the REDTOP detector. To improve the efficiency of the lead-glass tiles trapping Cherenkov light for energy reconstruction and particle identification, we optimized the application of a highly reflective coating. Through viscosity and thickness control, masking, and a custom spray technique, we refined the coating process to reduce surface defects and improve light yield. Together, these efforts strengthen the ICARUS neutrino program and REDTOP's capability of detecting rare decay events.

Visser, Erin [Michigan State U.] (ORCID:0009000184↗

NASA NTRS2000

Particle Engulfment and Pushing Micro-Gravity Experiments and Mathematical Modeling

The phenomenon of interaction of particles with solid-liquid interfaces that results in particle engulfment or pushing (PEP) has been Studied since mid 1960's. While the original interest stemmed from geology applications (frost heaving in soil), it was recognized early that understanding particle behavior at solidifying interfaces mi ht yield 9 practical benefits in other fields. In metallurgical applications the issue is the location of particles with respect to grain boundaries at the end of solidification. Considerable amount of experimental and theoretical research was lately focused on applications to metal matrix composites produced by casting; or spray forming techniques. Another application of PEP is in the growing of Y1Ba2CU3O7-delta(123) superconductor crystals from an undercooled liquid. The oxide melt contains Y2Ba1CU1O5 (211) precipitates, which act as flux pinning sites. The paper presents results of PEP micro-gravity research performed by the authors on two shuttle missions using metallic and polymeric materials. In addition. a discussion on the theoretical aspects of the physics of PEP is offered. Analytical and numerical models for planar solidification interfaces developed by the authors are used to explain the experimental results. Shortcomings of steady-state models are emphasized. A numerical model that includes the effect of the solutal field and of natural convection is introduced. A discussion of phenomena associated with dendritic solidification based on experimental observations is also offered. A mechanism of engulfment is proposed.

Stefanescu, Doru M.↗

DOE OSTI2021

Synthesis and Advanced Characterization of Polymer–Protein Core–Shell Nanoparticles

Enzyme immobilization techniques are widely researched due to their wide range of applications. Polymer–protein core–shell nanoparticles (CSNPs) have emerged as a promising technique for enzyme/protein immobilization via a self-assembly process. Based on the desired application, different sizes and distribution of the polymer–protein CSNPs may be required. This work systematically studies the assembly process of poly(4-vinyl pyridine) and bovine serum albumin CSNPs. Average particle size was controlled by varying the concentrations of each reagent. Particle size and size distributions were monitored by dynamic light scattering, ultra-small-angle X-ray scattering, small-angle X-ray scattering and transmission electron microscopy. Results showed a wide range of CSNPs could be assembled ranging from an average radius as small as 52.3 nm, to particles above 1 µm by adjusting reagent concentrations. In situ X-ray scattering techniques monitored particle assembly as a function of time showing the initial particle growth followed by a decrease in particle size as they reach equilibrium. The results outline a general strategy that can be applied to other CSNP systems to better control particle size and distribution for various applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2018

Does Orbital Angular Momentum Have Effect on Laser’s Scattering by Molecular Atmosphere?

Lasers with orbital angular momentum (OAM) have potential applications in communication technology, manipulation of particles, and remote sensing. Because of its unusual light-scattering properties, the OAM laser’s interaction with a molecular atmosphere must be studied to ensure that it is not lossy for communication or remote-sensing applications that involve its transmission through an atmospheric environment. In this study, the finite-difference time-domain (FDTD) method [21] is applied to calculate the light scattering of the purely azimuthal (the radial mode number is assumed to be zero) Laguerre-Gaussian (LG) beams with OAM by very small dielectric particles. Not like Lorentz-Mie solutions, the FDTD method can calculate for particles off the central axis of the LG beam. It is found that when the particles are very small, and the topological charge number of the OAM of a laser is not extremely large, the laser’s OAM has little effect on the scattering phase function. This suggests that Rayleigh theory can be applied directly to calculate the light scattering by atmospheric molecules. The transmission of a laser beam with OAM in a molecular atmosphere is not different from that of a regular Gaussian beam.

Molecular atmosphere↗

DOE OSTI2023

Hydrodynamic irreversibility of non-Brownian suspensions in highly confined duct flow

The irreversible behaviour of a highly confined non-Brownian suspension of spherical particles at low Reynolds number in a Newtonian fluid is studied experimentally and numerically. In the experiment, the suspension is confined in a thin rectangular channel that prevents complete particle overlap in the narrow dimension and is subjected to an oscillatory pressure-driven flow. In the small cross-sectional dimension, particles rapidly separate to the walls, whereas in the large dimension, features reminiscent of shear-induced migration in bulk suspensions are recovered. Furthermore, as a consequence of the channel geometry and the development and application of a single-camera particle tracking method, three-dimensional particle trajectories are obtained that allow us to directly associate relative particle proximity with the observed migration. Companion simulations of a steadily flowing suspension highly confined between parallel plates are conducted using the force coupling method, which also show rapid migration to the walls as well as other salient features observed in the experiment. While we consider relatively low volume fractions compared to most prior work in the area, we nevertheless observe significant and rapid migration, which we attribute to the high degree of confinement.

42 ENGINEERING↗

NASA NTRS2016

Health Monitoring of a Planetary Rover Using Hybrid Particle Petri Nets

This paper focuses on the application of a Petri Net-based diagnosis method on a planetary rover prototype.The diagnosis is performed by using a model-based method in the context of health management of hybrid systems.In system health management, the diagnosis task aims at determining the current health state of a system and the fault occurrences that lead to this state. The Hybrid Particle Petri Nets (HPPN) formalism is used to model hybrid systems behavior and degradation, and to define the generation of diagnosers to monitor the health states of such systems under uncertainty. At any time, the HPPN-based diagnoser provides the current diagnosis represented by a distribution of beliefs over the health states. The health monitoring methodology is demonstrated on the K11 rover. A hybrid model of the K11 is proposed and experimental results show that the approach is robust to real system data and constraints.

health monitoring↗

NASA NTRSDate not supplied

Demonstration of Capability to Simulate Particle Irregular Shape and Poly-Disperse Mixtures Within Lunar Lander Plume-Surface Interaction

Plume-Surface Interaction (PSI) between lander engine plumes and regolith soil creates hazards in obscuration and contamination by particle clouds, high-energy ejecta streams, and landing area cratering damage. The MSFC Fluid Dynamics Branch is developing simulation tools to offer a predictive PSI capability to NASA customers such as the Human Lander System (HLS) and Commercial Lunar Payload Services (CLPS). The Gas-Granular Flow Solver (GGFS) is the main application tool for coupled gas-particle two-phase flow simulations to predict the range of PSI effects from onset of surface erosion to deep crater formation. GGFS features an Eulerian-Eulerian modeling approach, treating both gas and granular material as interacting continuum phases. Modeling the lunar regolith granular material fluidic characteristics poses special challenges due to complex particle shapes and mixture composition. The lunar regolith is poorly sorted with broad particle size distributions and large fines content. It has significant cohesion, due to interlocking jagged particle shapes. Eulerian granular material flow modeling requires closure formulations for the granular material constitutive models (stress, friction, collisional and kinetic energy dissipation, drag, etc.). While closure models for spherical particles are available from particle kinetic theory, closure models for realistic non-spherical particles must be extracted from unit physics Discrete Element Model (DEM) particle interaction simulations and provided in the form of tabular datasets. The effects of particle irregular shape (non-spherical shape factors, angular particle surface roughness, and interlocking features) are simulated by approximating the particle features in the form of grouped elemental spheres to form composite particles in the DEM simulations. The effects of the wide range of regolith mixture particle sizes and the strong effects of the presence of the small particle sizes results in high cohesion and low porosity of the regolith mixture. The range of particle sizes is simulated by binning the particle sizes into an appropriate finite number of particle-size species and solving the problem as a species mixture. Combining these two modeling approaches enables simulations to capture both, the contributions of the irregular particle shape and the particle size distribution. The integration and maturation of the DEM-based constitutive model database generation process and poly-disperse mixture binning approach into the GGFS simulation framework are proceeding under funding by the NASA Game Changing Development program. The status of current capabilities will be presented in comparisons of crater characteristics resulting for spherical and irregular shape particles, and for mono-, bi-, and tri-disperse mixture simulations of Apollo LM plume-surface interaction. The computational results confirm the significance of including the particle shape and mixture effects. Going forward plans for the full implementation of the general poly-disperse regolith modeling capability and maturation towards NASA project application readiness under the GCD program will be presented.

Peter A Liever↗

NASA NTRSDate not supplied

Demonstration of Capability to Simulate Particle Irregular Shape and Poly-Disperse Mixtures Within Lunar Lander Plume-Surface Interaction

Plume-Surface Interaction (PSI) between lander engine plumes and regolith soil creates hazards in obscuration and contamination by particle clouds, high-energy ejecta streams, and landing area cratering damage. The MSFC Fluid Dynamics Branch is developing simulation tools to offer a predictive PSI capability to NASA customers such as the Human Lander System (HLS) and Commercial Lunar Payload Services (CLPS). The Gas-Granular Flow Solver (GGFS) is the main application tool for coupled gas-particle two-phase flow simulations to predict the range of PSI effects from onset of surface erosion to deep crater formation. GGFS features an Eulerian-Eulerian modeling approach, treating both gas and granular material as interacting continuum phases. Modeling the lunar regolith granular material fluidic characteristics poses special challenges due to complex particle shapes and mixture composition. The lunar regolith is poorly sorted with broad particle size distributions and large fines content. It has significant cohesion, due to interlocking jagged particle shapes. Eulerian granular material flow modeling requires closure formulations for the granular material constitutive models (stress, friction, collisional and kinetic energy dissipation, drag, etc.). While closure models for spherical particles are available from particle kinetic theory, closure models for realistic non-spherical particles must be extracted from unit physics Discrete Element Model (DEM) particle interaction simulations and provided in the form of tabular datasets. The effects of particle irregular shape (non-spherical shape factors, angular particle surface roughness, and interlocking features) are simulated by approximating the particle features in the form of grouped elemental spheres to form composite particles in the DEM simulations. The effects of the wide range of regolith mixture particle sizes and the strong effects of the presence of the small particle sizes results in high cohesion and low porosity of the regolith mixture. The range of particle sizes is simulated by binning the particle sizes into an appropriate finite number of particle-size species and solving the problem as a species mixture. Combining these two modeling approaches enables simulations to capture both, the contributions of the irregular particle shape and the particle size distribution. The integration and maturation of the DEM-based constitutive model database generation process and poly-disperse mixture binning approach into the GGFS simulation framework are proceeding under funding by the NASA Game Changing Development program. The status of current capabilities will be presented in comparisons of crater characteristics resulting for spherical and irregular shape particles, and for mono-, bi-, and tri-disperse mixture simulations of Apollo LM plume-surface interaction. The computational results confirm the significance of including the particle shape and mixture effects. Going forward plans for the full implementation of the general poly-disperse regolith modeling capability and maturation towards NASA project application readiness under the GCD program will be presented.

Peter A. Liever↗

DOE OSTI2024

ASIC Scoping Study Final Report

This report documents the results and findings of a one-year scoping study investigating multichannel readout application specific integrated circuits (ASICs) for interfacing to, and processing data from, silicon photomultiplier (SiPM) arrays. We document ASIC desired and required specifications for four applications supporting national security mission areas: neutron radiography, associated particle imaging, and two versions of kinematic neutron imaging cameras. While each application has a few unique requirements that stress capability, there is generally good agreement among most. Two recently developed ASIC devices were evaluated in a system-like configuration by interfacing these to scintillator crystals exposed to gamma and neutron sources. The 64-channel ORNL device delivered functional capability while meeting most mission requirements for neutron radiography. The Nalu Scientific device, a 32-channel full waveform digitizer, did not demonstrate reliable neutron / gamma separation but it is unclear if this was an ASIC issue or problems with test setup or firmware. A literature survey of other commercial and academic ASICs was undertaken to with the conclusion that existing devices do not meet all requirements.

42 ENGINEERING↗