Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen electrode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Study of oxygen gas production phenomenon during stand and discharge in silver-zinc batteries

The effects of a number of cell process and performance variables upon the oxygen evolution rate of silver/silver oxide cathodes are studied to predict and measure the conditions which would result in the production of a minimum of oxygen. The following five tasks comprise the study: the design and fabrication of two pilot test cells to be used for electrode testing; the determination of the sensitivity and accuracy of the test cell; the determination of total volumes and rates of generation by cathodes of standard production procedures; the construction of a sequential test plan; and the construction of a series of positive formation cells in which formation process factors can be controlled.

Source record↗
NASA NTRS1991

Reinterpretation of reduction potential measurements done by linear sweep voltammetry in silicate melts

The equilibrium concentrations of Ni between silicate melt and Pt were determined experimentally as a function of oxygen fugacity. The results demonstrate that metallic species derived in linear sweep voltammetry experiments in silicate melts are diffusing into Pt electrodes and not into the melt, as was concluded by previoius studies. This requires reinterpretation of previous linear sweep voltammetry results and recalculation and correction of reported reduction potentials. This paper reports these corrected reduction potentials. Also reported are the activity coefficients for Ni in synthetic basalt and diopsidic melts and for Co in diopsidic melt.

Colson, R. O.↗
NASA NTRS2001

Chemical State of Surface Oxygen on Carbon and Its Effects on the Capacity of the Carbon Anode in a Lithium-Ion Battery Investigated

In a lithium-ion battery, the lithium-storage capacity of the carbon anode is greatly affected by a surface layer formed during the first half cycle of lithium insertion and release into and out of the carbon anode. The formation of this solid-electrolyte interface, in turn, is affected by the chemistry of the carbon surface. A study at the NASA Glenn Research Center examined the cause-and-effect relations. Information obtained from this research could contribute in designing a high-capacity lithium-ion battery and, therefore, small, powerful spacecraft. In one test, three types of surfaces were examined: (1) a surface with low oxygen content (1.5 at.%) and a high concentration of active sites, (2) a surface with 4.5 at.% -OH or -OC type oxygen, and (3) a surface with 6.5 at.% O=C type oxygen. The samples were made from the same precursor and had similar bulk properties. They were tested under a constant current of 10 mA/g in half cells that used lithium metal as the counter electrode and 0.5 M lithium iodide in 50/50 (vol%) ethylene carbonate and dimethyl carbonate as the electrolyte. For the first cycle of the electrochemical test, the graph describes the voltage of the carbon anode versus the lithium metal as a function of the capacity (amount of lithium insertion or release). From these data, it can be observed that the surface with low oxygen and a high concentration of active sites could result in a high irreversible capacity. Such a high irreversible capacity could be prevented if the active sites were allowed to react with oxygen in air, producing -OH or -OC type oxygen. The O=C type oxygen, on the other hand, could greatly reduce the capacity of lithium intercalation and, therefore, needs to be avoided during battery fabrication.

Hung, Ching-Cheh↗
DOE OSTI2026

Field-Coupled Water Splitting with Metal-Free Donor–Acceptor Covalent Organic-Framework Junctions

Advancing metal-free electrocatalysts for hydrogen and oxygen evolution reactions (HER/OER) across acidic and alkaline media requires coordinated control of intermediate binding thermodynamics, interfacial charge delivery, and near-electrode transport dynamics. Here, we design amide-linked benzene–triazine covalent organic frameworks (BTA/TzTA-Hz COFs) and integrate them with carbon nanotubes (CNTs) to form COF–CNT junctions that establish a built-in interfacial electric field. Density functional theory (DFT) and electrostatic potential maps indicate complementary active motifs, with benzene-proximal fragments associated with HER and triazine-proximal motifs associated with OER. CNT integration shifts the contact-potential difference by ≈0.20 V, while operando electrochemical impedance spectroscopy suggests partially separable high-frequency junction-charging and lower-frequency Faradaic/transport responses. A 300 mT static magnetic field lowers the HER and OER overpotentials by tens of millivolts. Under anodic bias, the effective interfacial charging capacitance increases, and Mott–Schottky analysis shows an apparent ∼0.15 V flat-band shift with an essentially unchanged slope. Together, these observations are consistent with field-perturbed interfacial charging and altered bias partitioning. Field-dependent impedance and bubble imaging are consistent with magnetohydrodynamic convection that promotes bubble detachment and near-electrode mass transport for both half-reactions, and they reveal an OER-specific high-frequency perturbation under anodic bias. Under field, the heterostructure reaches an OER onset overpotential of ∼261 mV and requires an overpotential of 366 mV at 10 mA cm –2 in alkaline electrolyte. These results illustrate how reticular-framework chemistry, junction engineering, and both built-in and applied fields can program reactivity through interfacial electrostatics and near-electrode transport in organic-framework electrocatalysts.

Garcia-Enriquez, Lissette [Univ. of Texas at El Pa↗
DOE OSTI2024

Suppressing strain propagation in ultrahigh-Ni cathodes during fast charging via epitaxial entropy-assisted coating

Surface reconstruction and the associated severe strain propagation have long been reported as the major cause of cathode failure during fast charging and long-term cycling. Despite tremendous attempts, no known strategies can simultaneously address the electro-chemomechanical instability without sacrificing energy and power density. Here we report an epitaxial entropy-assisted coating strategy for ultrahigh-Ni LiNi x Co y Mn 1-x-y O 2 (x ≥ 0.9) cathodes via an oriented attachment-driven reaction between Wadsley-Roth phase-based oxides and the layered-oxide cathodes. Further, the high anti-cracking and anti-corrosion tolerances as well as the fast ionic transport of the entropy-assisted surface effectively improved the fast charging/discharging capability, wide temperature tolerance and thermal stability of the ultrahigh-Ni cathodes. Comprehensive analysis from the primary and secondary particle level to the electrode level using multi-scale in situ synchrotron X-ray probes reveals greatly reduced lattice dislocations, anisotropic lattice strain and oxygen release as well as improved bulk/local structural stability, even when charging beyond the threshold state of charge (75%) of layered cathodes. Layered Ni-rich oxide cathodes are susceptible to challenges with surface reconstruction and strain propagation, limiting their cyclability. The authors propose a solution involving oriented attachment-driven reactions, utilizing Wadsley-Roth nanocrystals and layered oxide to induce an epitaxial entropy-assisted coating, effectively addressing these issues.

25 ENERGY STORAGE↗
NASA NTRS1979

Economical synthesis of potassium superoxide

High-frequency discharge in oxygen can be used to prepare superoxides of alkali and alkaline-earth metals. Since no direct-current discharge at the electrodes is present, no sputtering can contaminate the product, hence a high conversion efficiency.

Bell, A. T.↗
DOE OSTI2020

Operando Revealing Dynamic Reconstruction of NiCo Carbonate Hydroxide for High-Rate Energy Storage

Transition metal carbonate hydroxide (CH) has been widely explored as a promising battery-type electrode for high-rate energy storage. However, its genuine active sites under realistic operating conditions remains elusive. In this work, by virtue of the cutting-edge operando X-ray absorption spectroscopy, we unfold the dynamic evolution of the local electronic and geometric structures for the CH electrode upon cycling. Our results reveal that the irreversible redox of Co cations at the early stage of cyclic voltammetry (CV) cycling induces a phase transition in the NiCo CH nanowires forming oxygen vacancies-enriched NiCo layered double hydroxide (LDH) nanosheets with superior high-rate energy storage ability. Theoretical modeling demonstrates that the unsaturated 5-coordinated Co sites exhibit optimal redox reaction energy barrier and immensely promote the performance. These findings not only elucidate the electrochemical susceptibility of the Co-based carbonate hydroxide under operando conditions, but also highlight an electrochemical coordination-engineering strategy for the rational design of high-performance electrode.

25 ENERGY STORAGE↗
DOE OSTI2022

Mesoporous Carbon-Based PGM-Free Catalyst Cathodes

Polymer electrolyte membrane fuel cell (PEMFC) is the most promising energy conversion technology which can be used as the power sources for the electric vehicles with the ultimate cleanness, (no carbon emission from the use of hydrogen), much-improved energy conversion efficiency, longer range, and rapid refueling. However, due to the large amount of platinum group metal (PGM) catalyst used in PEMFC electrodes, the high cost is the bottleneck for the broad commercialization of PEMFCs for transportation. Hence, there is a critical need to develop low-cost, high-performance PGM-free cathode catalysts that can dramatically reduce the cost of the catalyst in the PEMFC by one to two orders of magnitude. However, before PGM-free cathodes become viable, several technical challenges associated with PGM-free cathodes must be addressed, including the insufficient activity and stability of the catalysts as well as the large transport losses from the much thicker catalyst layer in the electrodes.

08 HYDROGEN↗
DOE OSTI2026

Influence of Pt-Metal Alloy Catalysts with Various Ionomers on Oxygen Reduction Reaction in Fuel Cell Application

Pt-M/C (M = Co, Ni, Mn, etc.) alloy catalysts exhibit superior oxygen reduction reaction (ORR) activity compared to pure Pt/C, leading to a high energy efficiency in hydrogen fuel cells. However, many Pt-M/C alloy catalysts were synthesized and evaluated at the lab scale in model test-bed systems like rotating disc electrodes, which don't always correlate to performance within a fuel cell system; there is a clear need to evaluate catalysts in electrodes that can be prepared at industrially relevant scales to evaluate how factors like ink formulation can greatly affect device-level of fuel cell performance. Herein, three commercial Pt-M/C alloy catalysts (two Pt-Co/C and one Pt-Ni/C) were comprehensively characterized by various techniques. The results show that the average particle sizes of the three catalysts are close to 5 nm; the atomic ratio of Pt/M is around 4; and the M was successfully embedded into Pt lattice, resulting in the positive shift of Pt 4f in XPS spectra and XRD patterns. These catalytic materials were incorporated into 9 different cathode catalyst layers (CCLs) with three kinds of ionomers (Nafion D2020, high oxygen permeability ionomer (HOPI), and Aquivion D79-25BS), and their performance in proton exchange membrane fuel cells (PEMFCs) were investigated. The results demonstrate that the Pt-Co/C catalysts possess a higher mass activity (MA) than Pt-Ni/C; the cathodes with Nafion ionomer provide the highest MA while electrodes with Aquivion ionomer showed the lowest activity, attributed to poor H+ conductivity resulting from suboptimal ionomer incorporation. Finally, these alloys were shown to exceed DOE targets for MA and H2/Air performance reported in the recent publications at beginning of life and after 90k cycle catalyst AST protocol. This study provides valuable performance benchmarks for these materials guiding future Pt-M/C catalyst design and material integration for heavy duty PEMFC applications.

08 HYDROGEN↗
DOE OSTI2024

Factors Affecting the Electron Conductivity in Single Crystal Li 7 La 3 Zr 2 O 12 and Li 7 P 3 S 11

One of the serious challenges in all solid-state Li ion batteries is neutral Li intrusion into the solid-state electrolyte that can ultimately cause catastrophic failure. One possibility for this is due to n-type electron conductivity that induces the reaction Li + + e – → Li 0 at sites where the potential is less than the Li + /Li potential. This paper reports hybrid density functional theory calculations of the electronic conductivity in two prototype single crystalline solid-state electrolytes, cubic Li 7 La 3 Zr 2 O 12 (c-LLZO) and Li 7 P 3 S 11 (LPS). The formation energies of important point defects that can affect electron conductivity are determined, and we find that the mechanism of n-type electron conductivity for both solid-state electrolytes is via “small” electron polaron hopping, where the quotes signify that substantial Li ion rearrangement is associated with the polaron formation and its migration. In both electrolytes, the formation energies for the small polarons at the Fermi energy are too high to generate measurable electron conductivity at room temperature. For c-LLZO, the concentration of electron polarons necessary to ensure charge neutrality from positively charged oxygen vacancies formed in synthesis can be significantly higher. Hence, the electron conductivity could be significant when measured with ion-blocking metal electrodes, and we discuss how the synthesis conditions could affect this magnitude. However, in the solid-state battery, these polarons are replaced by negatively charged Li vacancies so that the electron conductivity should remain minimal. For LPS single crystals, the inherent minimal electron conductivity is independent of synthesis conditions. Here we also show that the cost of forming Li 0 in bulk c-LLZO is enormous due to strain effects so that it could only potentially form at voids, grain boundaries, or around vacancy defects which relax the lattice strain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Material Discovery and Design Principles of Perovskite Oxides for Reversible Solid Oxide Cells (R-SOC)

Reversible solid oxide cells (R-SOCs) are highly efficient devices for energy conversion and storage, capable of operating for both hydrogen utilization and production. In fuel cell mode, an R-SOC consumes hydrogen or natural gas to generate electricity, while in electrolysis mode, it produces hydrogen from steam. The discover of new materials with rapid oxygen surface exchange kinetics and enduring stability is crucial for the economically viable commercialization of R-SOCs. To facilitate this pursuit, we conducted extensive Density Functional Theory (DFT) calculations and developed Machine Learning (ML) models to predict critical catalytic properties essential for R-SOCs, such as oxygen surface exchange/diffusivity, and area-specific resistance (ASR). BaCoxFeyZrzO3-d(BFCZ)(x+y+z=1) emerged as a promising family of electrode materials with high activity and stability, validated through systematic experimental study. Moreover, a robust numerical multiphysics model was developed to optimize materials and microstructure parameters, providing the ability to predict the performance of functional R-SOCs.

Liu, Jian↗
DOE OSTI2020

Significance of a Solid Electrolyte Interphase on Separation of Anode and Cathode Materials from Spent Li-Ion Batteries by Froth Flotation

The separation of electrode active materials from spent Li-ion batteries (LIBs) by froth flotation is challenging due to the changes in surface properties of electrode active materials from cycling as well as the presence of organic binders. In this work, the froth flotation separation of aged anode and cathode composite materials from spent LIBs was systematically investigated after the materials were heat treated. The results show that aged anode and cathode materials from spent LIBs can be well separated from each other after a heating process in air at 400 degrees C and at which some of the PVDF binder remains intact. The underlying mechanism was investigated by X-ray photoelectron spectroscopy (XPS), contact angle measurements, and scanning transmission electron microscopy (STEM) coupled with energy-dispersive X-ray spectroscopy (EDX). The results from the XPS and contact angle measurements show that there is a hydrophilic and oxygen-rich layer on the surface of aged anode materials. This hydrophilic surface, associated with the solid electrolyte interface (SEI) layer, impacts the froth flotation process significantly. The results also show that both the SEI layers and PVDF binder residues on the surface are removed at 400 degrees C for an hour, restoring the hydrophobicity of the anode materials, which, in turn, benefits the separation of anode and cathode materials. The STEM/EDX elemental analysis data confirms that there are 20 nm-thick oxygen-rich SEI layers on the surfaces, which can be removed after a heating process. The present result illustrates the significance of the SEI layers in flotation separation of electrode materials and sheds new lights into the future development of the recycling processes for the separation of anode and cathode composite materials from spent Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Probing Activities of Individual Catalytic Nanoflakes by Tunneling Mode of Scanning Electrochemical Microscopy

The tunneling mode of scanning electrochemical microscopy (SECM) was developed recently and applied to studies of charge-transfer reactions at single metal nanoparticles (NPs). When an SECM tip is brought within the tunneling distance from a conductive NP, the particle begins to act as a part of the nanoelectrode. Herein, we demonstrate the possibility of using carbon nanoelectrodes with a very thin insulating sheath for electrochemical tunneling experiments at flat samples. In this way, electrocatalytic activity, conductivity, and charging properties of and faradaic processes in layered nanomaterials can be characterized by single-nanoflake voltammetry without making direct ohmic contact with them. A broad applicability of tunneling SECM experiments is demonstrated by probing nanomaterials with different size, geometry, and electrocatalytic properties, including metallic/pseudo-metallic (1T/1T') and semiconducting (2H) MoS 2 nanoflakes, N-doped porous carbon catalyst, and MXene nanosheets. Further, the Tafel plots for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) at individual nanoflakes are compared to analogous measurements for an ensemble of flakes attached to the surface of a macroscopic electrode. Moreover, we observed variations in catalytic activities of individual MXene flakes toward HER and OER caused by non-uniform doping.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

An In-Depth Exploration of the Electrochemical Oxygen Reduction Reaction (ORR) Phenomenon on Carbon-Based Catalysts in Alkaline and Acidic Mediums

Detailed studies of the electrochemical oxygen reduction reaction (ORR) on catalyst materials are crucial to improving the performance of different electrochemical energy conversion and storage systems (e.g., fuel cells and batteries), as well as numerous chemical synthesis processes. In the effort to reduce the loading of expensive platinum group metal (PGM)-based catalysts for ORR in the electrochemical systems, many carbon-based catalysts have already shown promising results and numerous investigations on those catalysts are in progress. Most of these studies show the catalyst materials’ ORR performance as current density data obtained through the rotating disk electrode (RDE), rotating ring-disk electrode (RRDE) experiments taking cyclic voltammograms (CV) or linear sweep voltammograms (LSV) approaches. However, the provided descriptions or interpretations of those data curves are often ambiguous and recondite which can lead to an erroneous understanding of the ORR phenomenon in those specific systems and inaccurate characterization of the catalyst materials. In this paper, we presented a study of ORR on a newly developed carbon-based catalyst, the nitrogen-doped graphene/metal-organic framework (N-G/MOF), through RDE and RRDE experiments in both alkaline and acidic mediums, taking the LSV approach. The functions and crucial considerations for the different parts of the RDE/RRDE experiment such as the working electrode, reference electrode, counter electrode, electrolyte, and overall RDE/RRDE process are delineated which can serve as guidelines for the new researchers in this field. Experimentally obtained LSV curves’ shapes and their correlations with the possible ORR reaction pathways within the applied potential range are discussed in depth. We also demonstrated how the presence of hydrogen peroxide (H2O2), a possible intermediate of ORR, in the alkaline electrolyte and the concentration of acid in the acidic electrolyte can maneuver the ORR current density output in compliance with the possible ORR pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2003

Capacitive Sensors for Measuring Masses of Cryogenic Fluids

An effort is under way to develop capacitive sensors for measuring the masses of cryogenic fluids in tanks. These sensors are intended to function in both microgravitational and normal gravitational settings, and should not be confused with level sensors, including capacitive ones. A sensor of this type is conceptually simple in the sense that (1) it includes only one capacitor and (2) if properly designed, its single capacitance reading should be readily convertible to a close approximation of the mass of the cryogenic fluid in the tank. Consider a pair of electrically insulated electrodes used as a simple capacitive sensor. In general, the capacitance is proportional to the permittivity of the dielectric medium (in this case, a cryogenic fluid) between the electrodes. The success of design and operation of a sensor of the present type depends on the accuracy of the assumption that to a close approximation, the permittivity of the cryogenic fluid varies linearly with the density of the fluid. Data on liquid nitrogen, liquid oxygen, and liquid hydrogen, reported by the National Institute of Standards and Technology, indicate that the permittivities and densities of these fluids are, indeed, linearly related to within a few tenths of a percent over the pressure and temperature regions of interest. Hence, ignoring geometric effects for the moment, the capacitance between two electrodes immersed in the fluid should vary linearly with the density, and, hence, with the mass of the fluid. Of course, it is necessary to take account of the tank geometry. Because most cryogenic tanks do not have uniform cross sections, the readings of level sensors, including capacitive ones, are not linearly correlated with the masses of fluids in the tanks. In a sensor of the present type, the capacitor electrodes are shaped so that at a given height, the capacitance per unit height is approximately proportional to the cross-sectional area of the tank in the horizontal plane at that height (see figure).

Nurge, Mark↗
NASA NTRS1970

Oxygen-hydrogen fuel cell with an iodine-iodide cathode - A concept

Fuel cell uses a porous cathode through which is fed a solution of iodine in aqueous iodide solution, the anode is a hydrogen electrode. No activation polarization appears on the cathode because of the high exchange-current density of the iodine-iodide electrode.

Javet, P.↗
DOE OSTI2025

Electrochemical Corrosion and Catalysis Dynamics of Tin Oxide during Water Oxidation

Metal oxide corrosion severely limits anodic electrocatalysis, particularly at high potentials in acidic environments, where degradation pathways remain poorly defined. This study establishes explicit connections between corrosion and electrocatalysis on tin oxide during water oxidation by examining the roles of lattice defects, reactive oxygen species, interfacial pH variations, and speciation of corroded tin in acid. We first demonstrate the presence of structural defects such as oxygen vacancies and substoichiometric Sn(II) species by integrating electron paramagnetic resonance spectroscopy, ultraviolet photoelectron spectroscopy, and Mott–Schottky analysis. Kohn–Sham density functional theory calculations reveal that explicit water structures thermodynamically stabilize reaction intermediates and lower reaction overpotentials. Moreover, we propose that water dissociation leads to hydrogen-bonding networks formed by H* and OH* intermediates, which may span the entire catalyst surface and decrease the interfacial pH to drive corrosion. In contrast, the electrochemical generation of reactive oxygen species is shown to play a minor role in catalyst corrosion during water oxidation using inductively coupled plasma mass spectrometry coupled with selective chemical scavengers. Square-wave voltammetry combined with rotating ring-disk electrodes is used to reveal that under open-circuit conditions, only Sn(IV) cations chemically dissolve from tin oxide, while both Sn(IV) and Sn(II) species electrochemically corrode during water oxidation. Our results unveil a dynamic and complicated interplay between corrosive and catalytic pathways on metal oxide electrocatalysts: a decrease in interfacial pH due to water oxidation exacerbates Sn(II)/Sn(IV) corrosion. Subsequently, the electrochemical corrosion of Sn(II)/Sn(IV) facilitates product formation from lattice oxygen, while the redeposition of corroded Sn(II) as Sn(IV) can enable oxygen exchange with water. By elucidating the roles of defects and interfacial chemistry, this work provides a roadmap for engineering improved electrocatalysts that balance activity and stability, a critical step toward scalable and durable energy technologies.

36 MATERIALS SCIENCE↗