Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Metal Site Substitution and Role of the Dimer on Symmetry Breaking in FePS 3 and CrPS 4 under Pressure

We combine infrared absorption, Raman scattering, and diamond anvil cell techniques to explore the properties of FePS 3 and CrPS 4 under pressure, comparing our findings with a symmetry analysis, lattice dynamics calculations, and an examination of the energy landscape. Although these complex chalcogenides are considered to be members of the same family of materials, they display remarkably different phase progressions on account of the metal center orbital filling, character of the P–P linkage, layer corrugation, and differing size of the van der Waals gap. Here, we discuss the space group progressions, structure–property relations, and development of pressure-induced metallicity in terms of the competition between local and long-range symmetry transformations and structural distortion pathways. These findings place the properties of FePS 3 and CrPS 4 on a firm foundation for work under strain control and in the single layer limit.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Particle interspacing effects on the mechanical behavior of a Fe–TiB 2 metal matrix composite using FFT-based mesoscopic field dislocation mechanics

This paper presents an application to metal matrix composites (MMCs) of an enhanced elasto-viscoplastic Fast Fourier Transform (EVP-FFT) formulation coupled with a phenomenological continuum Mesoscale Field Dislocation Mechanics (MFDM) theory. Contrary to conventional crystal plasticity, which only accounts for plastic flow and hardening induced by statistically stored dislocations (SSDs), MFDM-EVP-FFT also describes the evolution of polarized geometrically necessary dislocation (GND) density and its effect on both plastic flow and hardening. Numerical results for a Fe–TiB 2 MMC made of a ferrite matrix (α-Fe) and elastic ceramic particles (TiB 2 ) are presented. Full-field simulations are performed using synthetic periodic unit cells representative of the MMC, with single-crystalline and polycrystalline matrix, for different particle interspacing distances. A strong dependence of the predicted equivalent stress, cumulated plastic strain and GND density fields with particle interspacing distance is observed, in contrast with conventional crystal plasticity. Correlations between these mechanical fields and microstructural features, and their influence on local and global mechanical behavior are examined for the different MMC microstructures.

42 ENGINEERING↗
DOE OSTI2020

Damage and Failure in a Statistical Crack Model

In this paper I will take a close look at a statistical crack model (SCM) as is used in engineering computer codes to simulate fracture at high strain rates. My general goal is to understand the macroscopic behavior effected by the microphysical processes incorporated into an SCM. More specifically, I will assess the importance of including local interactions between cracks into the growth laws of an SCM. My strategy will be to construct a numerical laboratory that represents a single computational cell containing a realization of a statistical distribution of cracks. The cracks will evolve by the microphysical models of the SCM, leading to quantifiable damage and failure of the computational cell. I will use the numerical data generated by randomly generated ensembles of the fracture process to establish scaling laws that will modify and simplify the implementation of the SCM into large scale engineering codes.

42 ENGINEERING↗
DOE OSTI2020

Shear Softening in a Metallic Glass: First-Principles Local-Stress Analysis

Metallic glasses deform elastically under stress. However, the atomic-level origin of elastic properties of metallic glasses remain unclear. In this Letter using ab initio molecular dynamics simulations of the Cu 5 0Zr 50 metallic glass under shear strain, we show that the heterogeneous stress relaxation results in the increased charge transfer from Zr to Cu atoms, enhancing the softening of the shear modulus. Changes in compositional short-range order and atomic position shifts due to the nonaffine deformation are discussed. It is shown that the Zr subsystem exhibits a stiff behavior, whereas the displacements of Cu atoms from their initial positions, induced by the strain, provide the stress drop and softening.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nanoscale phase transition in impact indented Mo/Cu thin films

The study reveals a size effect in deformation mechanisms via unique structural transitions in sputter deposited fcc/bcc nanolayers under high strain rate impact nanoindentation as layer thickness is reduced from around 100-200 nm to around 5 nm. Here, the indented 5 nm Cu/5 nm Mo multilayer films characterized via cross-sectional scanning/transmission electron microscopy have revealed a phase transition in the 5 nm thick Mo layers from BCC to a coherent metastable FCC structure and fine deformation twins in the 5 nm Cu layers inside a shear band that is approximately 500 nm long and inclined to the layer interfaces. In contrast, thicker layers, 80 nm Cu/180 nm Mo, show different deformation behavior with uneven layer thickness reduction, shearing of Cu layers, and bending of the columnar Mo grains beneath the indentation without any sign of shear band and localized phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the Cutting of Metals: A Mechanics Viewpoint

The mechanics of large-strain deformation in cutting of metals is discussed, primarily from viewpoint of recent developments in in situ analysis of plastic flow and microstructure characterization. It is shown that a broad range of deformation parameters can be accessed in chip formation—strains of 1–10, strain rates of 10–10 5 /s, and temperatures up to 0.7T m —and controlled. This range is far wider than achievable by any other single-stage, severe plastic deformation (SPD) process. The resulting extreme deformation conditions produce a rich variety of microstructures in the chip. Four principal types of chip formation—continuous, shear-localized, segmented, and mushroom-type—as elucidated first by Nakayama (1974, “The Formation of ‘Saw-Toothed Chip’ in Metal Cutting,” Proceedings of International Conference on Production Engineering, Tokyo, pp. 572–577) are utilized to emphasize the diverse plastic flow phenomena, especially unsteady deformation modes that prevail in cutting. These chip types are intimately connected with the underlying flow, each arising from a distinct mode and triggered by an instability phenomenon. The role of plastic flow instabilities such as shear banding, buckling, and fracture in mediating unsteady flow modes is expounded, along with consequences of the flow modes and chip types for the cutting. Sinuous flow is shown to be the reason why gummy (highly strain-hardening) metals, although relatively soft, are so difficult to cut. Synthesizing the various observations, a hypothesis is put forth that it is the stability of flow modes that determines the mechanics of cutting. Furthermore, this leads to a flow-stability phase diagram that could provide a framework for predicting chip types and process attributes.

42 ENGINEERING↗
DOE OSTI2025

A Combined Computational and Mathematical Analysis of Interconnect Fatigue Potential in Photovoltaic Modules

A finite element model of a 60-cell monocrystalline silicon glass-polymer photovoltaic module was simulated with ±1.0 kPa and ±2.4 kPa loads applied to the glass to calculate the deformation under load. Cell-to-cell displacements were used to approximate interconnect strain and stress. A mathematical fatigue cycle life relation was fitted to data for the interconnect material (copper), to generate a life prediction at each interconnect location based on the local stress means, reversal extents, and amplitudes. Interconnect stress was found to be significantly asymmetric about zero despite symmetric positive and negative module loads due to laminate thickness offsets about the neutral plane and the effects of module framing. Cycle life results indicated that interconnect fatigue failure was unlikely to occur over a 30-year lifetime of conservative wind and snow load cycles since the typical cell design feature of leaving some unconstrained length between the cell edge and first solder pad increases the effective gauge length and decreases the stress levels below the material endurance limit. Follow-up analyses found that 3.6 mm and 6.4 mm were the minimum unconstrained lengths required to survive the assumed lifetime of wind and snow cycles, respectively, confirming that typical industrial module constructions with 8–15 mm unconstrained lengths should survive conservatively. Notably, large magnitude, low-cycle snow loading was consistently the limiting factor requiring a longer unconstrained interconnect length. Finally, insights and workflows from this study inform module interconnection design limits for survival against mechanical fatigue in deployment environments.

14 SOLAR ENERGY↗
DOE OSTI2020

Controlling Metal–Organic Framework/ZnO Heterostructure Kinetics through Selective Ligand Binding to ZnO Surface Steps

Metal–organic framework (MOF) heterostructures exhibit unique properties beyond those of individual components, but their design requires an understanding of energetic and kinetic controls at MOF–substrate interfaces. Although the structural relationship has been widely used in heterostructure design, it overlooks the interplay between the organic ligand and the substrate which controls the kinetics and energetics of growth of the final structure. In this study, we used zeolitic imidazolate frameworks (ZIF-8) on ZnO as a model system to evaluate this interplay via in situ monitoring and simulations. Our results demonstrate multiple roles of the 2-methyl-imidazole (2-MIM) ligand as “dissolution-promoter”, “step-pinner”, and “terrace-binder” on the ZnO (001) face and “dissolution-promoter” and “terrace-binder” on the ZnO (100) face. Through these multiple face-specific roles, 2-MIM modulates ZnO dissolution kinetics and, hence, the Zn 2+ release rate, tuning local supersaturations that dictating the characteristic ZIF-8 crystallization kinetics on different substrate faces. The critical thickness for transition from 2D to 3D growth is dictated by competition between interfacial and strain energies. The atomic-scale mechanism of the coupled substrate dissolution and MOF growth, mediated by selective linker–substrate binding, furnishes a new synthesis pathway for other complex heterostructures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

NON-DESTRUCTIVE POST IRRADIATION EXAMINATION OF FIRST CYCLE ACCIDENT TOLERANT AND ADVANCED ZIRCONIUM ALLOY HIGH BURNUP FUEL RODS

Post irradiation examination (PIE) of accident tolerant fuel concepts and high burnup uranium dioxide advanced zirconium alloy clad fuel contribute to near term nuclear industry goals of enhancing light water reactor safety and economics. Westinghouse is developing chromium coated zirconium alloy cladding as an accident tolerant fuel option for current pressurized water reactors. Examination of high burnup fuel further augments the technical foundation for extending the peak rod average burnup limits beyond the current regulatory limit of 62 MWd/kgU. Seven fuel rods were received at the Oak Ridge National Laboratory Irradiated Fuel Examination Facility. This includes three chromium coated zirconium alloy fuel rods and four high burnup advanced zirconium alloy fuel rods. Six of the seven rods were fueled with standard uranium dioxide while one of the chromium coated rods contained Westinghouse’s ADOPT fuel. The overall hot-cell PIE plan and some PIE results have been presented previously. This paper focuses on the additional non-destructive examination and fission gas release. Highlights from visual examination of these rods are presented. The chromium coating showed little to no visual change following irradiation. Observations of the axial burnup trends in the fuel rods are derived from full rod axial gamma-ray scans with additional observations related to local fission product migration. The axial dimensional changes of the seven rods are evaluated. As expected, creep down had not yet occurred in the chromium coated rods, and the maximum diameter strain in the high burnup advanced zirconium alloy cladding was less than 0.5%. Finally, the steady state fission gas release for these rods was measured ranging from 4.1% to 17.6% which matched expectation from literature. These fuel rods now await further destructive examination.

Harp, Jason↗
DOE OSTI2024

Structure-Related Electronic and Magnetic Properties in Ultrathin Epitaxial Ni x Fe 3–x O 4 Films on MgO(001)

Off-stoichiometric Ni x Fe 3–x O 4 ultrathin films (x < 2.1) with varying Ni content x and thickness 16 (±2) nm were grown on MgO(001) by reactive molecular beam epitaxy. Synchrotron-based high-resolution X-ray diffraction measurements reveal vertical compressive strain for all films, resulting from a lateral pseudomorphic adaption of the film to the substrate lattice without any strain relaxation. Complete crystallinity with smooth interfaces and surfaces is obtained independent of the Ni content x. For x < 1 an expected successive conversion from Fe 3 O 4 to NiFe 2 O 4 is observed, whereas local transformation into NiO structures is observed for films with Ni content x > 1. However, angle-resolved hard X-ray photoelectron spectroscopy measurements indicate homogeneous cationic distributions without strictly separated phases independent of the Ni content, while X-ray absorption spectroscopy shows that also for x > 1, not all Fe 2+ cations are substituted by Ni 2+ cations. The ferrimagnetic behavior, as observed by superconducting quantum interference device magnetometry, is characterized by decreasing saturation magnetization due to the formation of antiferromagnetic NiO parts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Complex Oxides under Simulated Electric Field: Determinants of Defect Polarization in AB O 3 Perovskites

Abstract Polarization of ionic and electronic defects in response to high electric fields plays an essential role in determining properties of materials in applications such as memristive devices. However, isolating the polarization response of individual defects has been challenging for both models and measurements. Here the authors quantify the nonlinear dielectric response of neutral oxygen vacancies, comprised of strongly localized electrons at an oxygen vacancy site, in perovskite oxides of the form AB O 3 . Their approach implements a computationally efficient local Hubbard U correction in density functional theory simulations. These calculations indicate that the electric dipole moment of this defect is correlated positively with the lattice volume, which they varied by elastic strain and by A‐site cation species. In addition, the dipole of the neutral oxygen vacancy under electric field increases with increasing reducibility of the B‐site cation. The predicted relationship among point defect polarization, mechanical strain, and transition metal chemistry provides insights for the properties of memristive materials and devices under high electric fields.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Control of the Folding Dynamics of Self-Reconfiguring Magnetic Microbots Using Liquid Crystallinity

Reconfigurable microdevices are being explored in a range of contexts where their life-like abilities to move and change shape are important. While much work has been done to control the motion of these microdevices by engineering their geometry and composition, little is known about their dynamics in complex fluid environments with non-Newtonian rheology. Here in this paper, it is shown how the actuation dynamics of reconfigurable microdevices made by assembly of patchy magnetic microcubes, which are referred to as “microbots,” can be modulated by their interactions with the anisotropic viscoelastic environment of a liquid crystal (LC). The free energy arising from the elastic strain of LC and formation of topological defects around the microbots influences their folding dynamics, which can be tuned by tailoring both the far-field orientation of the LC and the local ordering of the LC at the microbot surfaces. These findings represent a first step toward establishing a general set of design rules to control the dynamics of microbots using complex anisotropic fluids.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancing the Reaction Kinetics and Stability of Co‐Free Li‐Rich Cathode Materials via a Multifunctional Strategy

Co-free Li-rich layered oxides (CFLLOs) with anionic redox activity are among the most promising cathode materials for high-energy-density and low-cost lithium-ion batteries (LIBs). However, irreversible oxygen release often causes severe structural deterioration, electrolyte decomposition, and the formation of unstable cathode-electrolyte interface (CEI) film with high impedance. Additionally, the elimination of cobalt elements further deteriorates the reaction kinetics, leading to reduced capacity and poor rate performance. Here, in this study, a multifunctional strategy is proposed, incorporating Li 2 MnO 3 phase content regulation, micro-nano structure design, and heteroatom substitution. The increased content of Li 2 MnO 3 phase enhances the capacity through oxygen redox. The smaller nanoscale primary particles induce greater tensile strain and introduce more grain boundaries, thereby improving the reaction kinetics and reactivity, while the larger micron-sized secondary particles help to reduce interfacial side reactions. Furthermore, Na⁺ doping modulates the local coordination environment of oxygen, stabilizing both the anion framework and the crystal structure. As a result, the designed cathode exhibits enhanced rate performance, delivering a capacity of 158 mAh g⁻¹ at 5.0 C and improved cyclic stability, with a high capacity retention of 99% after 400 cycles at 1.0 C. This multifunctional strategy holds great promise for advancing the practical application of CFLLOs in next-generation LIBs.

Co-free Li-rich layered oxide↗
DOE OSTI2021

Enhanced work hardening from oxygen-stabilized ω precipitates in an aged metastable β Ti-Nb alloy

High levels of oxygen in solid solution in Ti alloys are considered detrimental to mechanical properties because of embrittlement concerns. In metastable β titanium alloys, the formation of isothermal ω precipitates is also known to cause severe embrittlement and ductility reduction. However, oxygen has been shown to partition to the ω phase during ageing, and this partitioning behavior may potentially impact ω’s mechanical contribution. Using micropillar compression, we compared the deformation behavior of Ti-20Nb (at. %) with oxygen-stabilized ω precipitates to the behavior of oxygen-free specimens. The oxygen-stabilized microstructures showed increased compressive yield strength and enhanced work hardening behavior compared to oxygen-free specimens. In the absence of oxygen, the compressed pillars showed slip band formation and catastrophic failure, and transmission electron microscopy imaging revealed that ω precipitates were sheared within the continuous deformation channels resulting in slip localization. In contrast, oxygen-stabilized ω precipitates were harder to shear and the formation of continuous deformation channels was suppressed during compression, leading to improved work hardening behavior up to 15% strain. Furthermore, this counter-intuitive role of oxygen may offer design strategies to address the significant embrittlement and loss of ductility observed for ω-strengthened β Ti alloys without oxygen and avenues to expand the use of β Ti alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electricity from lignocellulosic substrates by thermophilic Geobacillus species

Given our vast lignocellulosic biomass reserves and the difficulty in bioprocessing them without expensive pretreatment and fuel separation steps, the conversion of lignocellulosic biomass directly into electricity would be beneficial. Here we report the previously unexplored capabilities of thermophilic Geobacillus sp. strain WSUCF1 to generate electricity directly from such complex substrates in microbial fuel cells. This process obviates the need for exogenous enzymes and redox mediator supplements. Cyclic voltammetry and chromatography studies revealed the electrochemical signatures of riboflavin molecules that reflect mediated electron transfer capabilities of strain WSUCF1. Proteomics and genomics analysis corroborated that WSUCF1 biofilms uses type-II NADH dehydrogenase and demethylmenaquinone methyltransferase to transfer the electrons to conducting anode via the redox active pheromone lipoproteins localized at the cell membrane.

09 BIOMASS FUELS↗
DOE OSTI2025

Strain-induced superconductivity in RuO 2 (100) thin-films

Recently, superconductivity was discovered with a superconducting transition temperature (T c ) of 2 K in strained (110)-oriented RuO 2 films grown on TiO 2 (110) single-crystal substrates. In this work, we predict and realize superconductivity in strained (100)-oriented RuO 2 thin films grown on TiO 2 (100) single-crystal substrates. We show that while density functional theory predicts the T c of strained RuO 2 (100) films to be even higher than the RuO 2 (110) films, our transport and angle-resolved photoemission spectroscopy measurements find the T c to be about 1 K in strained RuO 2 (100) films grown on TiO 2 (100) substrates. Nonetheless, the thickness dependence of the T c follows a similar trend in both cases. Our scanning SQUID measurements reveal a local superfluid response, indicating a 100 mK inhomogeneity in T c over a 100 μm scale.

Electronic structure↗
DOE OSTI2021

A strain-driven thermotropic phase boundary in BaTiO 3 at room temperature by cycling compression

In BaTiO 3 single crystals, we observed a strain-driven phase transition from the tetragonal phase to the tetragonal-orthorhombic phase boundary which can be introduced by slow cycling compressions (a loading of up to 0.5 GPa, strain rate of 10 -4 s -1 , and 100 cycles) at room temperature. Different from the well-known tetragonal to cubic phase transition under stress (~2 GPa), it only takes place locally around bent 90° domain walls. The inhomogeneous local stress and electrical fields as well as the mobile point defect pinning effect contribute to the phase re-entrance. Through comparison experiments by in situ synchrotron x-ray diffraction, Raman scattering, and (scanning) transmission electron microscopy, we explored the phase transition mechanism. Based on that, we developed a mechanical method to obtain well-stabilized high-density thermotropic phase boundary structures (with tetragonal, orthorhombic, and bridging monoclinic phases) in BaTiO 3 for potential applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Linking Domain Structure Evolution at a Grain Boundary to Piezoelectric Response via Nano‐Diffraction

Electric-field-induced domain structure switching in a 1 𝜇⁢m -thick Pb 0.99 (Zr 0.45 Ti 0.55 ) 0.98 Nb 0.02 O 3 (Nb-doped PZT) bicrystal film was characterized in situ via nano-focused synchrotron diffraction. The epitaxial film was deposited on a (100) SrTiO 3 bicrystal substrate. The changes in domain structure were mapped within a 5 𝜇⁢m × 5 𝜇⁢m area at and around an in-plane tilt-type (23.6°) grain boundary with 50 nm spatial resolution. Rocking curves collected at each point of the mapped area provided the ability to reconstruct spatially-varying three-dimensional (3D) reciprocal space maps around the grain boundary. The 3D reciprocal space maps reveal how different tilted 𝑎 -type domain variants interact with the grain boundary as a function of increasing electric field. Initially, a subset of 𝑎 -type domain variants with their polarization vectors largely orthogonal to the grain boundary were found in greater abundance within 570 nm of the grain boundary, possibly due to X-ray beam-induced local increases in the electrical conductivity, but after the coercive field was exceeded, reconfiguration of the ferroelastic domains was observed. The spatially-varying reciprocal space maps also facilitated evaluation of the strain field across the mapped area, along with 𝑑 33,𝑓 . Significant spatial heterogeneity of strain and 𝑑 33,𝑓 are observed, especially at the coercive field, which was attributed to maintaining deformation compatibility and correlated ferroelastic switching.

36 MATERIALS SCIENCE↗