Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “injection test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1927

A Preliminary Study of Fuel Injection and Compression Ignition as Applied to an Aircraft Engine Cylinder

This report summarizes some results obtained with a single cylinder test engine at the Langley Field Laboratory during a preliminary investigation of the problem of applying fuel injection and compression ignition to aircraft engines. For this work a standard Liberty Engine cylinder was fitted with a high compression, 11.4 : 1 compression ratio, piston, and equipped with an airless injection system, including a primary fuel pump, an injection pump, and an automatic injection valve. The results obtained during this investigation have indicated the possibility of applying airless injection and compression ignition to a cylinder of this size, 8-inch bore by 7-inch stroke, when operating at engine speeds as high as 1,850 R. P. M. A minimum specific fuel consumption with diesel engine fuel oil of 0.30 pound per I. HP. Hour was obtained when developing about 16 B. HP. At 1,730 R. P. M.

Gardiner, Arthur W↗
NASA NTRS1979

Performance of a multiple venturi fuel-air preparation system

Spatial fuel-air distributions, degree of vaporization, and pressure drop were measured 16.5 cm downstream of the fuel injection plane of a multiple Venturi tube fuel injector. Tests were performed in a 12 cm tubular duct. Test conditions were: a pressure of 0.3 MPa, inlet air temperature from 400 to 800K, air velocities of 10 and 20 m/s, and fuel-air ratios of 0.010 and 0.020. The fuel was Diesel #2. Spatial fuel-air distributions were within + or - 20 percent of the mean at inlet air temperatures above 450K. At an inlet air temperature of 400K, the fuel-air distribution was measured when a 50 percent blockage plate was placed 9.2 cm upstream of the fuel injection plane to distort the inlet air velocity fuel injection plane to distort the inlet air velocity profile. Vaporization of the fuel was 50 percent complete at an inlet air temperature of 400K and the percentage increased linearly with temperature to complete vaporization at 600K. The pressure drop was 3 percent at the design point which was three times greater than the designed value and the single tube experiment value. No autoignition or flashback was observed at the conditions tested.

Tacina, R. R.↗
NASA NTRS1960

Measurements of Skin Friction of the Compressible Turbulent Boundary Layer on a Cone with Foreign Gas Injection

Measurements of average skin friction of the turbulent boundary layer have been made on a 15deg total included angle cone with foreign gas injection. Measurements of total skin-friction drag were obtained at free-stream Mach numbers of 0.3, 0.7, 3.5, and 4.7 and within a Reynolds number range from 0.9 x 10(exp 6) to 5.9 x 10(exp 6) with injection of helium, air, and Freon-12 (CCl2F2) through the porous wall. Substantial reductions in skin friction are realized with gas injection within the range of Mach numbers of this test. The relative reduction in skin friction is in accordance with theory-that is, the light gases are most effective when compared on a mass flow basis. There is a marked effect of Mach number on the reduction of average skin friction; this effect is not shown by the available theories. Limited transition location measurements indicate that the boundary layer does not fully trip with gas injection but that the transition point approaches a forward limit with increasing injection. The variation of the skin-friction coefficient, for the lower injection rates with natural transition, is dependent on the flow Reynolds number and type of injected gas; and at the high injection rates the skin friction is in fair agreement with the turbulent boundary layer results.

Pappas, Constantine C.↗
NASA NTRS1988

A fault injection experiment using the AIRLAB Diagnostic Emulation Facility

The preparation for, conduct of, and results of a simulation based fault injection experiment conducted using the AIRLAB Diagnostic Emulation facilities is described. An objective of this experiment was to determine the effectiveness of the diagnostic self-test sequences used to uncover latent faults in a logic network providing the key fault tolerance features for a flight control computer. Another objective was to develop methods, tools, and techniques for conducting the experiment. More than 1600 faults were injected into a logic gate level model of the Data Communicator/Interstage (C/I). For each fault injected, diagnostic self-test sequences consisting of over 300 test vectors were supplied to the C/I model as inputs. For each test vector within a test sequence, the outputs from the C/I model were compared to the outputs of a fault free C/I. If the outputs differed, the fault was considered detectable for the given test vector. These results were then analyzed to determine the effectiveness of some test sequences. The results established coverage of selt-test diagnostics, identified areas in the C/I logic where the tests did not locate faults, and suggest fault latency reduction opportunities.

Baker, Robert↗
DOE OSTI2021

Production, fuel properties and combustion testing of an iso-olefins blendstock for modern vehicles

With the increasing pressure to decarbonize the transportation sector, exploring strategies that can reduce emissions from light-duty vehicles (LDV) has become critical. Bioblendstocks that allow for higher engine efficiency and fuel economy could complement vehicle electrification and help reach carbon neutrality by 2050. In this context, the potential of a mixture of iso-olefins as a bioblendstock was investigated for multimode boosted spark-ignition (SI)/advanced compression ignition (ACI) engine operation designed to achieve higher overall vehicle fuel economy. By establishing the relationship between the molecular structure of iso-olefins and research octane number (RON), octane sensitivity (S) (i.e., the difference between RON and motor octane number [MON]), and phi-sensitivity a dimethyl-hexenes rich olefins mixture (DMHROM) was identified as a preferred blendstock for SI/ACI combustion engines. Here, a pathway for DMHROM production from biomass-derived ethanol was developed and scaled up. More than 1 gallon of DMHROM blendstock was produced for fuel properties assessment including engine testing. Measurements in a Cooperative Fuel Research Engine showed that the DMHROM blendstock possesses a RON of 94 and S of 13.5, and blends synergistically. Rapid compression machine tests coupled with single-cylinder gasoline direct injection engine measurements demonstrated the 20 vol.% DMHROM blend has higher phi-sensitivity than an olefin-free gasoline base fuel and a typical California Reformulated Gasoline Blendstock for Oxygenate Blending (CARBOB) gasoline fuel. These results demonstrate the potential of DMHROM for improving gasoline fuel performance and quality for operation under ACI conditions. The effectiveness of the aftertreatment system in mitigating emissions was verified and showed that the pure DMHROM blendstock and 20 vol.% blend would not increase non-methane organic gases, NO x , and carbon monoxide (CO) emissions. The DMHROM blendstock was found to slightly decrease sooting tendency when added to a gasoline-base fuel (i.e., ~6% reduction at 20 vol.% blending level). Oxidation stability and lubricant compatibility were both confirmed for the 20 vol.% blend. Overall, these results demonstrate that dimethyl-hexenes have potential for improving engine efficiency and fuel economy while meeting emissions regulations and ASTM specifications for gasoline fuel.

09 BIOMASS FUELS↗
DOE OSTI2021

Stability and pulsation of the first dark stars

ABSTRACT The first bright objects to form in the Universe might not have been ‘ordinary’ fusion-powered stars, but ‘dark stars’ (DSs) powered by the annihilation of dark matter (DM) in the form of weakly interacting massive particles (WIMPs). If discovered, DSs can provide a unique laboratory to test DM models. DSs are born with a mass of the order of M⊙ and may grow to a few million solar masses; in this work we investigate the properties of early DSs with masses up to $\sim \! 1000 \, \mathrm{ M}_\odot$, fueled by WIMPS weighing 100 GeV. We improve the previous implementation of the DM energy source into the stellar evolution code mesa. We show that the growth of DSs is not limited by astrophysical effects: DSs up to $\sim \!1000 \, \mathrm{ M}_{\odot }$ exhibit no dynamical instabilities; DSs are not subject to mass-loss driven by super-Eddington winds. We test the assumption of previous work that the injected energy per WIMP annihilation is constant throughout the star; relaxing this assumption does not change the properties of the DSs. Furthermore, we study DS pulsations, for the first time investigating non-adiabatic pulsation modes, using the linear pulsation code gyre. We find that acoustic modes in DSs of masses smaller than $\sim \! 200 \, \mathrm{ M}_\odot$ are excited by the κ − γ and γ mechanism in layers where hydrogen or helium is (partially) ionized. Moreover, we show that the mass-loss rates potentially induced by pulsations are negligible compared to the accretion rates.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

First Ever Polymer Flood Field Pilot to Enhance the Recovery of Heavy Oils on Alaska North Slope – Producer Responses and Operational Lessons Learned

The US Department of Energy and Hilcorp Alaska, LLC are jointly cosponsoring a field pilot project entitled “First Ever Field Pilot on Alaska’s North Slope to Validate the Use of Polymer Floods for Heavy Oil Enhanced Oil Recovery (EOR).” The objective of this pilot is to perform a field experiment to validate the use of an advanced polymer flooding technology to unlock the vast heavy oil resources on Alaska North Slope (ANS). Two pairs of horizontal injection and production wells have been deployed in an isolated fault block of the Schrader Bluff heavy oil reservoir at the Milne Point Field to conduct a polymer flood pilot which was designed to acquire field performance data to optimize polymer flood design in the Schrader Bluff heavy oil reservoirs on ANS. Hydrolyzed polyacrylamide (HPAM) polymer injection started on August 28, 2018 using a custom made polymer mixing and pumping unit. Polymer solution properties such as concentration, viscosity, and filter ratio, have been closely monitored and adjusted as necessary. Operational procedures have been improved to ensure adequate injectivity and polymer propagation through the formation. Oil and water production is tested frequently to monitor water cut performance, and produced water is sampled and analyzed for polymer content. Tracers were pumped pre and post polymer injection startup to compare polymer flood breakthrough timing and sweep efficiency. Polymer injectivity of the horizontal wells drilled in the Schrader Bluff NB sand is found to be sufficient to replace the reservoir production voidage although there were some declines as high viscosity polymer swept the near wellbore region. Production data show significant reduction in water cut and the oil production rate has stabilized. No polymer production has been confirmed from the two horizontal producers after 22 months of polymer injection into the two supporting horizontal injectors. Tracer data show very low sweep efficiencies with waterflood alone, whereas significant improvement has been achieved with polymer flood. Many operational lessons have been learned and improvements have been made regarding polymer mixing, pumping, and onsite quality control, particularly in a challenging Arctic environment. Adequate polymer injection rate can be achieved with diligent monitoring and quality assurance of the properties of the injected polymer solution.

Ning, Samson↗
DOE OSTI2023

A Bifunctional Pt/CeO 2 -Cu 1 /CeO 2 Catalyst System for Isooctane Oxidation under Fully Simulated Engine-Exhaust Condition: Eliminating the Inhibition by CO

Pt-based catalysts, because of their outstanding activity for hydrocarbon oxidation, are widely used in the engine-exhaust aftertreatment system to remove hydrocarbon emissions. However, the CO and NO x present in real engine exhausts compete with hydrocarbons for active Pt sites, and thus inhibit hydrocarbon oxidation. In this work, we evaluated the inhibition effects of CO and NO on isooctane oxidation over a Pt/CeO 2 catalyst under the simulated condition of the US DRIVE test protocol (S-GDI, stoichiometric gasoline direct injection). We also leveraged a low-cost single-atom Cu 1 /CeO 2 catalyst, which is highly active for low-temperature CO oxidation, to eliminate the inhibition effect of CO. Specifically, by physically mixing Cu 1 /CeO 2 and Pt/CeO 2 , all the CO is completely converted below 200 °C under simulated exhaust condition, which helps lower the isooctane oxidation temperature. However, the unconverted NO still strongly suppresses HC oxidation. Possible strategies to address the NO inhibitor were proposed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1971

Experiment M408: Beta spectrometer

The beta spectrometer functioned as planned throughout the Gemini 10 mission. The cool temperatures that were recorded from the instrument during the mission were indicative that the evaporative cooler, coupled with apparently lower-than-expected spacecraft-adapter temperatures, maintained ideal operating conditions. The data facilitate a good analysis of the electron directional distribution. The omnidirectional flux that was calculated is apparently consistent with previous measurements. Representative electron spectra, measured during the Gemini 12 mission, established the apparent decay of the artificially injected electrons (from the Starfish high altitude nuclear test) to such low levels that natural trapped electrons were becoming detectable.

Marbach, J. R.↗
NASA NTRS1972

Fault-tolerance experiments with the JPL STAR computer.

Results of fault-tolerance experiments performed using an experimental computer with dynamic (standby) redundancy, including replaceable subsystems and a 'program rollback' provision to eliminate transient-caused errors. After a brief review of the specification of fault-tolerance with respect to transient faults, including a description of the method of injection of transient faults in software and system tests, fault-tolerance experiments carried out with this computer with regard to the determination of fault classes, software verification, system verification, and recovery stability are summarized. A test and repair processor is described which constitutes a special monitor unit of the computer and is used to obtain information for fault detection in the other subsystems of the computer and to ensure that proper recovery occurs when a fault is detected.

Avizienis, A.↗
NASA NTRS1975

Large Deployable Antenna Shuttle Experiment

An experiment designed to use the Space Shuttle in tests of the mechanical and electrical properties of spaceborne deployable antennas under zero-gravity conditions is outlined. Space-erectable 20-meter diameter phased arrays or reflector/feed systems, and self-deploying mechanisms, are to be tested. Reflector surface integrity will be tested by an AM laser technique, and electrical behavior will be tested by a spin-stabilized RF beacon injected into orbit prior to unfurlment of the antenna. Focusing and gain measurements, static pattern measurements, dynamic RF gain measurements, and measurements of cross-polarized signals will be conducted, and the reflector will be illuminated by separate feeds for the S-, X-, and K-bands. Mechanical features of the mesh-wrapped rib furlable antenna design are described.

Freeland, R. E.↗
NASA NTRS1980

Solar Power Satellite (SPS) fiber optic link assessment

A feasibility demonstration of a 980 MHz fiber optic link for the Solar Power Satellite (SPS) phase reference distribution system was accomplished. A dual fiber-optic link suitable for a phase distribution frequency of 980 MHz was built and tested. The major link components include single mode injection laser diodes, avalanche photodiodes, and multimode high bandwidth fibers. Signal throughput was demonstrated to be stable and of high quality in all cases. For a typical SPS link length of 200 meters, the transmitted phase at 980 MHz varies approximately 2.5 degrees for every deg C of fiber temperature change. This rate is acceptable because of the link length compensation feature of the phase control design.

Source record↗
NASA NTRS1990

NASA systems autonomy demonstration project: Advanced automation demonstration of Space Station Freedom thermal control system

The NASA Systems Autonomy Demonstration Project (SADP) was initiated in response to Congressional interest in Space station automation technology demonstration. The SADP is a joint cooperative effort between Ames Research Center (ARC) and Johnson Space Center (JSC) to demonstrate advanced automation technology feasibility using the Space Station Freedom Thermal Control System (TCS) test bed. A model-based expert system and its operator interface were developed by knowledge engineers, AI researchers, and human factors researchers at ARC working with the domain experts and system integration engineers at JSC. Its target application is a prototype heat acquisition and transport subsystem of a space station TCS. The demonstration is scheduled to be conducted at JSC in August, 1989. The demonstration will consist of a detailed test of the ability of the Thermal Expert System to conduct real time normal operations (start-up, set point changes, shut-down) and to conduct fault detection, isolation, and recovery (FDIR) on the test article. The FDIR will be conducted by injecting ten component level failures that will manifest themselves as seven different system level faults. Here, the SADP goals, are described as well as the Thermal Control Expert System that has been developed for demonstration.

Dominick, Jeffrey↗
NASA NTRS1990

Analog-digital simulation of transient-induced logic errors and upset susceptibility of an advanced control system

A simulation study is described which predicts the susceptibility of an advanced control system to electrical transients resulting in logic errors, latched errors, error propagation, and digital upset. The system is based on a custom-designed microprocessor and it incorporates fault-tolerant techniques. The system under test and the method to perform the transient injection experiment are described. Results for 2100 transient injections are analyzed and classified according to charge level, type of error, and location of injection.

Carreno, Victor A.↗
NASA NTRS1992

Using the Viking biology experimental results to obtain chemical information about Martian regolith

Although initially formulated as biology experiments, most of the results produced by the Viking Labeled Release (LR), Gas Exchange (GEX), and Pyrolytic Release (PR) experiments have been reproduced by chemical means. The experiments do not need more study as 'biological' phenomena, but they do deserve much more careful consideration from a chemical viewpoint. They are the only 'wet-chemical' experiments that scientists have performed on another planet, but they have not found very general use as sources of scientific information. There is a large set of potentially useful chemical observations, e.g., the three resolvable and precisely measured kinetic components of the release of C-14-labeled gases, the thermal sensitivity and magnitudes of the oxidation reaction(s) of the LR experiments, the kinetics and magnitude of the O2 and CO2 release of the GEX experiments, the thermal sensitivity of the GEX results, the differences between the thermal sensitivity of the GEX and the thermal sensitivity of the LR responses, and the kinetics and magnitudes of the LR successive injection reabsorption effect. It should be possible to test many chemical aspects of hypothetical martian phenomena in experiments using the biology experimental configurations and derive much valuable information by comparisons with the Viking observations.

Plumb, Robert C.↗
NASA NTRS1993

Three-dimensional modeling of diesel engine intake flow, combustion and emissions-2

A three-dimensional computer code, KIVA, is being modified to include state-of-the-art submodels for diesel engine flow and combustion. Improved and/or new submodels which have already been implemented and previously reported are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NO(x), and spray/wall impingement with rebounding and sliding drops. Progress on the implementation of improved spray drop drag and drop breakup models, the formulation and testing of a multistep kinetics ignition model, and preliminary soot modeling results are described. In addition, the use of a block structured version of KIVA to model the intake flow process is described. A grid generation scheme was developed for modeling realistic (complex) engine geometries, and computations were made of intake flow in the ports and combustion chamber of a two-intake-value engine. The research also involves the use of the code to assess the effects of subprocesses on diesel engine performance. The accuracy of the predictions is being tested by comparisons with engine experiments. To date, comparisons were made with measured engine cylinder pressure, temperature and heat flux data, and the model results are in good agreement with the experiments. Work is in progress that will allow validation of in-cylinder flow and soot formation predictions. An engine test facility is described that is being used to provide the needed validation data. Test results were obtained showing the effect of injection rate and split injections on engine performance and emissions.

Reitz, R. D.↗
NASA NTRS1994

Experimental investigation of nozzle/plume aerodynamics at hypersonic speeds

Much of the work involved the Ames 16-Inch Shock Tunnel facility. The facility was reactivated and upgraded, a data acquisition system was configured and upgraded several times, several facility calibrations were performed and test entries with a wedge model with hydrogen injection and a full scramjet combustor model, with hydrogen injection, were performed. Extensive CFD modeling of the flow in the facility was done. This includes modeling of the unsteady flow in the driver and driven tubes and steady flow modeling of the nozzle flow. Other modeling efforts include simulations of non-equilibrium flows and turbulence, plasmas, light gas guns and the use of non-ideal gas equations of state. New experimental techniques to improve the performance of gas guns, shock tubes and tunnels and scramjet combustors were conceived and studied computationally. Ways to improve scramjet engine performance using steady and pulsed detonation waves were also studied computationally. A number of studies were performed on the operation of the ram accelerator, including investigations of in-tube gasdynamic heating and the use of high explosives to raise the velocity capability of the device.

Bogdanoff, David W.↗