Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Data-Driven Modeling of a High Capacity Cryogenic System for Control Optimization

The Cryogenic Moderator System (CMS) is responsible for maintaining a steady flow of cold neutrons for numerous physics experiments at the Spallation Neutron Source (SNS) in Oak Ridge National Laboratory (ORNL). Sudden losses in beam power, known as beam trips, cause a major disturbance to the CMS due to large step changes in cooling demands. Ongoing efforts on upgrading the neutron beam power from 1.4 to 2.0MW are expected to generate larger transients that can further strain the CMS subsystems if they are not properly controlled. To manage such disturbances, four flow valves and one electric heater are adjusted by five decentralized proportional-integral-derivative (PID) controllers. However, the original PID gains were calibrated empirically based only on tracking performance and not based on disturbance rejection. To address this issue without compromising current CMS operations, a control-oriented model was developed to recalibrate the PID controllers offline. The zero-dimensional (0-D) model was based on simple physics-based principles and data-driven system identification techniques. The CMS was broken into several subsystems for analysis, each of which corresponds to a parametric model tied to the thermodynamic states of the working fluid. The model parameters were identified using the nonlinear least squares method where the residuals were calculated from available sensor data. Simulation results show that the proposed model can capture the dynamics of the CMS at steady state and during beam trips.

Maldonado Puente, Bryan↗
DOE OSTI2020

Electron Transfer in Microemulsion-Based Electrolytes

The use of flowing electrochemical reactors, for example, in redox flow batteries and in various electrosynthesis processes, is increasing. This technology has the potential to be of central significance in the increased deployment of renewable electricity for carbon-neutral processes. A key element of optimizing efficiency of electrochemical reactors is the combination of high solution conductivity and reagent solubility. In this work, we show a substantial rate of charge transfer for an electrochemical reaction occurring in a microemulsion containing electroactive material is loaded inside the nonpolar (toluene) subphase of the microemulsion. The measured rate constant translates to an exchange current density comparable to that in redox flow batteries. The rate could be controlled by the surfactant, which maintains partitioning of reactants and products by forming an interfacial region with ions in the aqueous phase in close proximity. The hypothesized echanism is evocative of membrane-bound enzymatic reactions. Achieving sufficient rates of electrochemical reaction is the product of an effort designed to establish a reaction condition that meets the requirements of electrochemical reactors using microemulsions to realize a separation of conducting and reactive elements of the solution, opening a door to the broad use of microemulsions to effect controlled electrochemical reactions as steps in more complex processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Modeling the role of lateral surface flow in low‐relief polygonal tundra

Abstract Ice‐wedge polygon troughs play an important role in controlling the hydrology of low‐relief polygonal tundra regions. Lateral surface flow is confined to troughs only, but it is often neglected in model projections of permafrost thermal hydrology. Recent field and modeling studies have shown that, after rain events, increases in trough water levels are significantly more than the observed precipitation, highlighting the role of lateral surface flow in the polygonal tundra. Therefore, understanding how trough lateral surface flow can influence polygonal tundra thermal hydrology is important, especially under projected changes in temperatures and rainfall in the Arctic regions. Using an integrated cryohydrology model, this study presents plot‐scale end‐of‐century projections of ice‐wedge polygon water budget components and active layer thickness with and without trough lateral surface flow under the Representative Concentration Pathway 8.5 scenario. Trough lateral surface flow is incorporated through a newly developed empirical model, evaluated against field measurements. The numerical scenario that includes trough lateral surface flow simulates discharge (outflow from a polygon) and recharge (rain‐induced inflow to a polygon trough from upslope areas), while the scenario that does not include trough lateral surface flow ignores recharge. The results show considerable reduction (about 100–150%) in evapotranspiration and discharge in rainy years in the scenarios ignoring trough lateral surface flow, but less effect on soil water storage, in comparison with the scenario with trough lateral surface flow. In addition, the results demonstrate long‐term changes (~10–15 cm increase) in active layer thickness when trough lateral surface flow is modeled. This study highlights the importance of including lateral surface flow processes to better understand the long‐term thermal and hydrological changes in low‐relief polygonal tundra regions under a changing climate.

Jan, Ahmad↗
DOE OSTI2021

High-Level Synthesis of Parallel Specifications Coupling Static and Dynamic Controllers

The increased need for efficient ways to implement domain-specific accelerators is driving design methodologies towards the use of abstractions higher than the Register Transfer Level (RTL). In this scenario, High Level Synthesis (HLS) plays a significant role by enabling the automatic generation of custom hardware accelerators starting from high level descriptions (e.g., C code). Conventional HLS tools exploit parallelism mostly at the Instruction Level (ILP). They statically schedule the input specifications, and build centralized Finite State Machine (FSM) controllers. However, aggressive exploitation of ILP in many applications has diminishing returns and, usually, centralized approaches do not efficiently exploit coarser parallelism because FSMs are inherently serial. In this paper we present a HLS framework able to synthesize applications that, beside ILP, also expose Task Level Parallelism (TLP). An application can expose TLP through annotations that identify the parallel functions (i.e., tasks). To generate accelerators that efficiently execute concur- rent tasks, we need to solve several issues: devise a mechanism to support concurrent execution flows, exploit memory parallelism, and manage synchronization. To support concurrent execution flows, we introduce a novel adaptive controller. The adaptive controller is composed of a set of interacting control elements that independently manage the execution of a single operation or function call. These control elements check dependencies and resource constraints at runtime, enabling as soon as possible execution. To support parallel access to shared memories and synchronization, we introduce a novel Hierarchical Memory Interface (HMI). With respect to previous solutions, the proposed interface supports multi-ported memories and atomic memory operations, which commonly occur in parallel programming. Our framework can generate the hardware implementation of C functions by employing two different approaches, depending on its characteristics. If a function exposes TLP, then the framework generates hardware implementations based on the adaptive controller. Otherwise, the framework implements the function by exploiting a more conventional FSM approach, which is optimized for ILP exploitation. We evaluate our framework on a set of parallel applications, and show substantial performance improvements (average speedup of 4.7) with limited area over- heads (average area increase of 5.48 times).

Castellana, Vito G.↗
DOE OSTI2021

High-Level Synthesis of Parallel Specifications Coupling Static and Dynamic Controllers

The increased need for efficient ways to implement domain-specific accelerators is driving design methodologies towards the use of abstractions higher than the Register Transfer Level (RTL). In this scenario, High Level Synthesis (HLS) plays a significant role by enabling the automatic generation of custom hardware accelerators starting from high level descriptions (e.g., C code). Conventional HLS tools exploit parallelism mostly at the Instruction Level (ILP). They statically schedule the input specifications, and build centralized Finite State Machine (FSM) controllers. However, aggressive exploitation of ILP in many applications has diminishing returns and, usually, centralized approaches do not efficiently exploit coarser parallelism because FSMs are inherently serial. In this paper we present a HLS framework able to synthesize applications that, beside ILP, also expose Task Level Parallelism (TLP). An application can expose TLP through annotations that identify the parallel functions (i.e., tasks). To generate accelerators that efficiently execute concur- rent tasks, we need to solve several issues: devise a mechanism to support concurrent execution flows, exploit memory parallelism, and manage synchronization. To support concurrent execution flows, we introduce a novel adaptive controller. The adaptive controller is composed of a set of interacting control elements that independently manage the execution of a single operation or function call. These control elements check dependencies and resource constraints at runtime, enabling as soon as possible execution. To support parallel access to shared memories and synchronization, we introduce a novel Hierarchical Memory Interface (HMI). With respect to previous solutions, the proposed interface supports multi-ported memories and atomic memory operations, which commonly occur in parallel programming. Our framework can generate the hardware implementation of C functions by employing two different approaches, depending on its characteristics. If a function exposes TLP, then the framework generates hardware implementations based on the adaptive controller. Otherwise, the framework implements the function by exploiting a more conventional FSM approach, which is optimized for ILP exploitation. We evaluate our framework on a set of parallel applications, and show substantial performance improvements (average speedup of 4.7) with limited area over- heads (average area increase of 5.48 times).

Castellana, Vito G.↗
DOE OSTI2020

Design and analysis of a wake steering controller with wind direction variability

Wind farm control strategies are being developed to mitigate wake losses in wind farms, increasing energy production. Wake steering is a type of wind farm control in which a wind turbine's yaw position is misaligned from the wind direction, causing its wake to deflect away from downstream turbines. Current modeling tools used to optimize and estimate energy gains from wake steering are designed to represent wakes for fixed wind directions. However, wake steering controllers must operate in dynamic wind conditions and a turbine's yaw position cannot perfectly track changing wind directions. Research has been conducted on robust wake steering control optimized for variable wind directions. In this paper, the design and analysis of a wake steering controller with wind direction variability is presented for a two-turbine array using the FLOw Redirection and Induction in Steady State (FLORIS) control-oriented wake model. First, the authors propose a method for modeling the turbulent and low-frequency components of the wind direction, where the slowly varying wind direction serves as the relevant input to the wake model. Next, we explain a procedure for finding optimal yaw offsets for dynamic wind conditions considering both wind direction and yaw position uncertainty. We then performed simulations with the optimal yaw offsets applied using a realistic yaw offset controller in conjunction with a baseline yaw controller, showing good agreement with the predicted energy gain using the probabilistic model. Using the Gaussian wake model in FLORIS as an example, we compared the performance of yaw offset controllers optimized for static and dynamic wind conditions for different turbine spacings and turbulence intensity values, assuming uniformly distributed wind directions. For a spacing of five rotor diameters and a turbulence intensity of 10 %, robust yaw offsets optimized for variable wind directions yielded an energy gain equivalent to 3.24 % of wake losses recovered, compared to 1.42 % of wake losses recovered with yaw offsets optimized for static wind directions. In general, accounting for wind direction variability in the yaw offset optimization process was found to improve energy production more as the separation distance increased, whereas the relative improvement remained roughly the same for the range of turbulence intensity values considered.

17 WIND ENERGY↗
DOE OSTI2024

Development of a Distribution Optimal Power Flow Federate for Open-Source OEDI-SI Platform

Increasing numbers of distributed generators in the electric power distribution networks require developing a control strategy to optimize solutions in real time. Linearized optimal distribution flow development has seen growth and acceptance in the distribution systems literature for efficiently modeling the \glspl{opf} for distribution systems. This paper examines the implementation and integration procedure for linearized optimal distribution flow federate to \gls{oedisi} platform. Specifically, we discuss i) the usage of the \gls{oedisi} platform, ii) obtaining a tractable solution using developed \gls{opf} federate, and iii) validation of solutions and bench-marking the \gls{oedisi} platform with developed \gls{opf} federate using OpenDSS. In brief, we demonstrate how a general linearized optimal distribution flow federate can be developed and integrated with a co-simulation environment to mimic real-world examples. The efficacy of the proposed method is demonstrated using the IEEE 123-bus test system under different scenarios to obtain a tractable solution and compare its results.

Sadnan, Rabayet↗
DOE OSTI2022

Flow Loop Study of ECT-Based Volume Fraction Monitoring in Oil–Water Two-Phase Flows

Measurement of phase volume fractions in water-containing multiphase flows is necessary for the optimization of a host of industrial flow processes. Many water-containing multiphase flows can be classified as either water-dispersed or water-continuous mixtures. A recently developed approach based on Hanai’s mixture formula and utilizing electrical capacitance tomography (ECT) sensors have shown good potential for obtaining water volume fraction estimates in two-phase water-containing flows with different water salinity levels. However, the proposed approach was investigated via controlled experiments restricted to static configurations while, in practice, multiphase flows can be dynamic and unpredictable. In this work, we perform a flow loop study of the proposed ECT-based method for volume fraction estimation in oil–water two-phase flows. Here, we evaluate the performance of the proposed method in both water-dispersed and water-continuous flow regimes by employing different types of capacitive sensors in cylindrical arrangements and parallel-plate rectangular arrangements.

02 PETROLEUM↗
DOE OSTI2025

Predicting Selective Laser Printing Print Quality of Polymer Powders through Melt Flow Index

Selective Laser Sintering (SLS) uses a precisely controlled laser to fuse polymer powder to build complex 3D shapes. While SLS covers a wide application space, the processing knowledge of polymer powder is limited, restricting the number of commercial powders available. This study serves to expand the processing knowledge of polypropylene and polyethylene in parallel with a “mature” SLS feedstock, nylon, through melt flow index (MFI) characterization. Differential Scanning Calorimetry (DSC) was used to explore the sintering window of the polymers. Polyethylene and polypropylene exhibited a relatively narrow sintering window between 4 – 5 °C, whereas the sintering window of nylon was much wider, between 23 – 24 °C. This suggests that the print quality between polyethylene and polypropylene would be similar; however, X-ray computed tomography revealed a higher volume of print defects, voids, and de lamination in polyethylene than in polypropylene. MFI analysis provided additional insight into the difference in print quality, as the MFI of polyethylene was 7.16 g/10 min, 9.95 g/10 min for polypropylene, and 17.23 g/10 min for nylon. MFI is inversely correlated to melt viscosity, and a low melt viscosity is desired for proper coalescing between the layers and particles. These results suggest that MFI is a promising tool, in conjunction with traditional thermal analysis, for screening candidate powder feedstocks for SLS and optimization of print parameters for novel powders.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Longitudinal coherence and short-term wind speed prediction based on a nacelle-mounted Doppler lidar

The spatial structure of turbulence in atmospheric boundary layer flows is highly relevant to wind energy. In particular, wind turbine control strategies based on inflow preview measurements require knowledge of the longitudinal evolution of turbulent flow as it approaches the rotor. These upstream measurements are usually obtained with nacelle-mounted wind lidars. In contrast to traditional in situ anemometry, lidars collect measurements within a probe volume which varies in size depending on the technology of the commercial system being used. Here, we address two issues related to the use of wind lidar to measure the incoming flow to a wind turbine: (i) whether existing longitudinal coherence models can be used to predict flow at the rotor, based on measurements performed at a distance away from the rotor; and (ii) what effect probe-volume averaging has on the inflow predictions. These two questions are critical to the design and implementation of robust wind turbine control strategies. To address these questions, we perform field measurements and large-eddy simulations to determine which incoming flow structures can be readily predicted with existing coherence models, and which require additional corrections to account for lidar volumetric averaging effects. Results reveal that the wind turbine induction zone has a negligible impact on the longitudinal coherence and first-order turbulence quantities, such as the standard deviation of velocity fluctuations. However, the phase of the signal, from which advection time periods of the turbulent structures are derived, is affected by the rotor blockage effect.

17 WIND ENERGY↗
DOE OSTI2021

Design and analysis of a wake model for spatially heterogeneous flow

Abstract. Methods of turbine wake modeling are being developed to more accurately account for spatially variant atmospheric conditions within wind farms. Most current wake modeling utilities are designed to apply a uniform flow field to the entire domain of a wind farm. When this method is used, the accuracy of power prediction and wind farm controls can be compromised depending on the flow-field characteristics of a particular area. In an effort to improve strategies of wind farm wake modeling and power prediction, FLOw Redirection and Induction in Steady State (FLORIS) was developed to implement sophisticated methods of atmospheric characterization and power output calculation. In this paper, we describe an adapted FLORIS model that features spatial heterogeneity in flow-field characterization. This model approximates an observed flow field by interpolating from a set of atmospheric measurements that represent local weather conditions. The objective of this method is to capture heterogeneous atmospheric effects caused by site-specific terrain features, without explicitly modeling the geometry of the wind farm terrain. The implemented adaptations were validated by comparing the simulated power predictions generated from FLORIS to the actual recorded wind farm output from the supervisory control and data acquisition (SCADA) recordings and large eddy simulations (LESs). When comparing the performance of the proposed heterogeneous model to homogeneous FLORIS simulations, the results show a 14.6 % decrease for mean absolute error (MAE) in wind farm power output predictions for cases using wind farm SCADA data and a 18.9 % decrease in LES case studies. The results of these studies also indicate that the efficacy of the proposed modeling techniques may vary with differing site-specific operational conditions. This work quantifies the accuracy of wind plant power predictions under heterogeneous flow conditions and establishes best practices for atmospheric surveying for wake modeling.

17 WIND ENERGY↗
DOE OSTI2025

Assimilating partial observation to enhance feedback control of stochastic dynamical systems

Here, in this paper, we present a novel methodology to tackle feedback optimal control problems in scenarios where the exact state of the controlled process is unknown. It integrates data assimilation techniques and optimal control solvers to manage partial observation of the state process, a common occurrence in practical scenarios. Traditional stochastic optimal control methods assume full state observation, which is often not feasible in real-world fluid dynamics control problems. Our approach underscores the significance of utilizing observational data to inform control policy design. Specifically, we introduce a kernel learning backward stochastic differential equation (SDE) filter to enhance data assimilation efficiency and propose a sample-wise stochastic optimization method within the stochastic maximum principle framework. We demonstrate the efficacy and accuracy of our method in the control of advection-diffusion-reaction flow problem and the Dubins airplane maneuvering problem with model uncertainty.

data driven↗
DOE OSTI2023

Integrated Process Optimization for Biochemical Conversion

This research is motivated by the challenges faced during biomass processing in bioenergy plants. It has been observed that variations in biomass characteristics, such as moisture, ash, and carbohydrate contents cause variations in feeding of the system which led to underutilization of equipment and the reactor. The objective of this research is to ensure a continuous flow of biomass to the reactor in plants that use the biochemical conversion process to generate liquid fuels. The overall goal is to lower the cost of producing biofuels, which could lead to improving US’s energy independency and growing US’s rural economy. The research team developed analytical models, such as discrete element method (DEM) models and mathematical models. The DEM models are unit-level models that explicitly capture biomass characteristics and quantify the impacts of biomass characteristics on bulk material properties and the performance of specific equipment. The mathematical models are system-level models that capture the impacts of system infeed rate, equipment processing rate, storage location and capacity, and biomass characteristics on system throughput. The functional relations predicting the bulk material properties from DEM models are incorporated to the mathematical models. The models developed were validated and evaluated using data collected at Idaho National Laboratory’s biomass processing facility. Via these models, we identified process control strategies that ensure a continuous flow of biomass to the reactor, while meeting the requirements of biochemical conversion process. Our analysis indicates that sequencing of biomass bales based on moisture level, and carbohydrate contents could have a positive impact on reducing processing time and inventory level and increasing throughput rate. Short bale sequences that repeat frequently, seem to have the greatest impact on improving system’s performance. Based on our experiments, the total annual system operating costs reduced by 20-30%, and the maximum inventory level reduced by 3 to 4 times. The operating costs include the annual equipment amortization cost and processing cost. The implementation of the models developed requires the use of standardized bale format, Radio Frequency Identification technology, sensing and real time monitoring of material attributes, automated material handling equipment, and automated process control. The scope of the model proposed can be extended to include the whole supply chain. The supply chain models help identify how many bales of different biomass feedstock to purchase given biomass availability in the region, biomass price and quality, and the biomass processing capabilities of the biorefinery. Thus, the outcomes of supply chain models can be used to inform the design of long-term contracts among farmers and the biorefinery.

09 BIOMASS FUELS↗
DOE OSTI2022

Reactive Transport Modeling of Mineral Precipitation and Carbon Trapping in Discrete Fracture Networks

In this study we use numerical experiments to analyze reactive flow and transport behavior in discrete intersecting fracture networks, focusing on (a) how reaction-induced changes in physical and chemical properties affect flow connectivity and (b) how fracture networks developed in the Earth's critical zone contribute to carbon sequestration via mineral weathering reactions. In the first part of the study, we used two-dimensional reactive flow and transport simulations to analyze the impacts of mixing in a natural discrete fracture network. We concluded that reaction-induced changes can substantially alter the flow connectivity, especially at fracture intersections. The second set of simulations considered the problem of natural weathering of fractured mafic and ultramafic rocks in the partially saturated Earth's critical zone as a function of infiltration rates, fracture permeability, and partially saturated flow parameters. As a model system, we considered an incongruent reaction network with dissolution of forsterite and precipitation of magnesite. The behavior is complex in terms of the rate-controlling processes because of the multicomponent nature of the system as shown by the grid Peclet number: the CO 2 behavior is gas diffusion-controlled in the partially saturated zone, while the rate of water flow via the Damkӧhler number controls Mg 2+ transport through the fracture network. The amounts of carbon that can be trapped are modest, but the naturally fractured domain considered here provides a useful “base case” against which various engineered solutions can be compared.

58 GEOSCIENCES↗
DOE OSTI2024

Demonstrating autonomous controls on hardware test beds is a necessity for successful missions to Mars and beyond

NASA and the Department of Defense are planning for a mission to Mars in the 2030s–2040s using nuclear thermal propulsion (NTP). NTP uses a nuclear reactor to heat flowing hydrogen and create thrust. A serious concern for crewed and uncrewed missions to Mars is the loss of reactor control. The reactor startup and initial rocket impulse are initiated in cislunar or near-earth orbital regions; therefore, radio communications between ground control and the NTP engine should occur in real time. However, radio communications can take more than 20 min, depending on planet positions, to reach Mars orbiters from ground control. To address this delay, local autonomous controls are implemented onboard the NTP engine to ensure acceptable operation. However, autonomous controls have not been demonstrated or implemented in research or power reactor contexts because of safety and reliability concerns. To enable autonomous controls development, demonstration, and validation, Oak Ridge National Laboratory has created a nonnuclear hardware-in-the-loop test bed. Sensors throughout the test bed relay system status and hardware response to the user control algorithm, including measurements of temperature, flow, pressure of a loop, control drum position, and drum speed. This paper discusses the development of this facility and user accessibility.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Results from a wake-steering experiment at a commercial wind plant: investigating the wind speed dependence of wake-steering performance

Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to redirect their wakes away from downstream turbines, thereby increasing the net wind plant power production and reducing fatigue loads generated by wake turbulence. In this paper, we present results from a wake-steering experiment at a commercial wind plant involving two wind turbines spaced 3.7 rotor diameters apart. During the 3-month experiment period, we estimate that wake steering reduced wake losses by 5.6% for the wind direction sector investigated. After applying a long-term correction based on the site wind rose, the reduction in wake losses increases to 9.3%. As a function of wind speed, we find large energy improvements near cut-in wind speed, where wake steering can prevent the downstream wind turbine from shutting down. Yet for wind speeds between 6–8 m/s, we observe little change in performance with wake steering. However, wake steering was found to improve energy production significantly for below-rated wind speeds from 8–12 m/s. By measuring the relationship between yaw misalignment and power production using a nacelle lidar, we attribute much of the improvement in wake-steering performance at higher wind speeds to a significant reduction in the power loss of the upstream turbine as wind speed increases. Additionally, we find higher wind direction variability at lower wind speeds, which contributes to poor performance in the 6–8 m/s wind speed bin because of slow yaw controller dynamics. Further, we compare the measured performance of wake steering to predictions using the FLORIS (FLOw Redirection and Induction in Steady State) wind farm control tool coupled with a wind direction variability model. Although the achieved yaw offsets at the upstream wind turbine fall short of the intended yaw offsets, we find that they are predicted well by the wind direction variability model. When incorporating the expected yaw offsets, estimates of the energy improvement from wake steering using FLORIS closely match the experimental results.

17 WIND ENERGY↗
DOE OSTI2022

An Open-Source Frequency-Domain Model for Floating Wind Turbine Design Optimization

A new frequency-domain dynamics model has been developed that uses open-source components to efficiently represent a complete floating wind turbine system. The model, called RAFT (Response Amplitudes of Floating Turbines), incorporates quasi-static mooring reactions, strip-theory and potential-flow hydrodynamics, blade-element-momentum aerodynamics, and linear turbine control. The formulation is compatible with a wide variety of support structure configurations and no manual or time-domain preprocessing steps are required, making RAFT very practical in design and optimization workflows. The model is applied to three reference floating wind turbine designs and its predictions are compared with results from time-domain OpenFAST simulations. There is good agreement in mean offsets as well the statistics and spectra of the dynamic response, verifying RAFT’s general suitability for floating wind analysis. Follow-on work will include verification of potential-flow and turbine-control features and application to optimization problems.

17 WIND ENERGY↗
DOE OSTI2022

A Simplified Numerical Approach to Characterize the Thermal Response of a Moving Bed Solar Reactor

Abstract Concentrated solar thermochemical storage in the form of a zero-emission fuel is a promising option to produce long-duration energy storage. Solar fuel is produced using a cavity reactor that captures concentrated solar radiation from a solar field of heliostats. In this paper, heat transfer model of a tubular plug-flow reactor designed and manufactured for a solar fuel production is presented. Experimental data collected from a fixed bed tubular reactor testing are used for model comparison. The system consists of an externally heated tube with counter-current flowing gas and moving solid particles as the heated media. The proposed model simulates the dynamic behavior of temperature profiles of the tube wall, gas, and particles under various gas flowrates and residence times. The heat transfer between gas–wall, solid particle–wall, and gas–solid particle is numerically studied. The model results are compared with the results of experiments done using a 4 kW furnace with a 150 mm heating zone surrounding a horizontal alumina tube (reactor) with 50.8 mm outer diameter and thickness of 3.175 mm. Solid fixed particles of magnesium manganese oxide (MgMn2O4) with the size of 1 mm are packed within the length of 250 mm at the center of the tube length. Simulation results are assessed with respect to fixed bed experimental data for four different gas flowrates, namely, 5, 10, 15, and 20 standard liters per minute of air, and furnace temperatures in the range of 200–1200 °C. The simulation results showed good agreement with maximum steady state error that is less than 6% of those obtained from the experiments for all runs. The proposed model can be implemented as a low-order physical model for the control of temperature inside plug-flow reactors for thermochemical energy storage applications.

Engineering↗