Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “finishing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Thin aluminum filters for use on the Apollo Telescope Mount XUV spectrographs

Thin, unbacked, aluminum film filters were used on two extreme ultraviolet (XUV) instruments flown on the Apollo Telescope Mount of Skylab by the Naval Research Laboratory to transmit the XUV radiation while blocking the longer wavelength radiation that would saturate the detector. The requirements placed on these filters - large size, resistance to degradation by high acoustic and vibration fields, and low pinhole transmittances - were far more severe than those placed on any filters previously flown. Special techniques were developed for vacuum evaporation of the aluminum, removal of the films from the substrates, supporting the films and mounting them to obtain finished filters, and storing them so that no degradation took place. A description of these techniques will be given.

Schumacher, R. J.↗
NASA NTRS1978

Form die and glide plates for vacuum brazing

Die for fabricating steel retorts is made from commercial plywood with steel facing. Smooth-finished glide plates prevent partial bonding of plates to stainless-steel parts.

Beuyukian, C. S.↗
NASA NTRS1978

Long-term CF6 engine performance deterioration: Evaluation of engine S/N 451-479

The performance testing and analytical teardown of CF6-6D engine is summarized. This engine had completed its initial installation on DC-10 aircraft. The investigative test program was conducted inbound prior to normal overhaul/refurbishment. The performance testing included an inbound test, a test following cleaning of the low pressure turbine airfoils, and a final test after leading edge rework and cleaning the stage one fan blades. The analytical teardown consisted of detailed disassembly inspection measurements and airfoil surface finish checks of the as received deteriorated hardware. Included in this report is a detailed analysis of the test cell performance data, a complete analytical teardown report with a detailed description of all observed hardware distress, and an analytical assessment of the performance loss (deterioration) relating measured hardware conditions to losses in both SFC (specific fuel consumption) and EGT (exhaust gas temperature).

Kramer, W. H.↗
NASA NTRS1978

Lubrication and failure mechanisms of graphite fluoride films

An optical microscope, equipped with a vertical illuminator and two polaroid filters (one rotatable), was used to visually study 440C HT steel surfaces lubricated with rubbed graphite fluoride films. Friction and wear results were compared to visual observations as a function of sliding distance for films applied to three surface finishes - polished, sanded, and sand-blasted. In general, the lubricating process was one of initial deformation or wear of metallic asperities into flat plateaus and then the formation of thin, layer-like, dynamic films which sheared between the flats and eventually flowed through the contact area. Failure was due to depletion of the graphite fluoride with the subsequent formation of excessive powdery metallic debris that formed a heavy, powdery film on both the rider and disk surfaces.

Fusaro, R. L.↗
NASA NTRS1977

Technological development of cylindrical and flat shaped high energy density capacitors

Cylindrical wound metallized film capacitors rated 2 micron F 500 VDC that had an energy density greater than 0.3 J/g, and flat flexible metallized film capacitors rated at 2 micron F 500 VDC that had an energy density greater than 0.1 J/g were developed. Polysulfone, polycarbonate, and polyvinylidene fluoride (PVF2) were investigated as dielectrics for the cylindrical units. PVF2 in 6.0 micron m thickness was employed in the final components of both types. Capacitance and dissipation factor measurements were made over the range 25 C to 100 C, and 10 Hz to 10 kHz. No pre-life-test burning was performed, and six of ten cylindrical units survived a 2500 hour AC plus DC lift test. Three of the four failures were infant mortality. All but two of the flat components survived 400 hours. Finished energy densities were 0.104 J/g at 500 V and 0.200 J/g at 700 V, the energy density being limited by the availability of thin PVF2 films.

Zelik, J. A.↗
NASA NTRS1978

Structured programming: Principles, notation, procedure

Structured programs are best represented using a notation which gives a clear representation of the block encapsulation. In this report, a set of symbols which can be used until binding directives are republished is suggested. Structured programming also allows a new method of procedure for design and testing. Programs can be designed top down, that is, they can start at the highest program plane and can penetrate to the lowest plane by step-wise refinements. The testing methodology also is adapted to this procedure. First, the highest program plane is tested, and the programs which are not yet finished in the next lower plane are represented by so-called dummies. They are gradually replaced by the real programs.

JOST↗
NASA NTRS1978

Wide temperature range fiber optic cable: Cable design study

Factors considered in the design and fabrication of a single fiber optic cable intended for spacecraft applications in an environment of temperature extremes from -160 C to 125 C include: abrasion resistance, low temperature flexibility, small size, low weight, and overall temperature stability. Specific requirements were identified for fiber core and overall diameters, fiber loss and NA, and cable tensile load. The single fiber cable will be fabricated by using a chemical vapor step index fiber of .125 mm coated to .3 mm with RTV silicone and then extruded with a jacket of Teflon PFA to a diameter of .5 mm. Six yarns of 1420 denier unimpregnated Kevlar 49 with a helical lay of 1.3 inches will surround the jacketed fiber under an extrusion of PFA. The finished cable diameter will measure 1.8 mm, and the weight of one kilometer length will be approximately 4350grams.

Speed, E. U.↗
NASA NTRS1976

Oil-air mist lubrication for helicopter gearing

The applicability of a once-through oil mist system to the lubrication of helicopter spur gears was investigated and compared to conventional jet spray lubrication. In the mist lubrication mode, cooling air was supplied at 366K (200 F) to the out of mesh location of the gear sets. The mist air was also supplied at 366K (200 F) to the radial position mist nozzle at a constant rate of 0.0632 mol/s (3 SCFM) per nozzle. The lubricant contained in the mist air varied between 32 - 44 cc/hour. In the recirculating jet spray mode, the flow rate was varied between 1893 - 2650 cc/hour. Visual inspection revealed the jet spray mode produced a superior surface finish on the gear teeth but a thermal energy survey showed a 15 - 20% increase in heat generated. The gear tooth condition in the mist lubrication mode system could be improved if the cooling air and lubricant/air flow ratio were increased. The test gearbox and the procedure used are described.

Mcgrogan, F.↗
NASA NTRS1978

Long-term CF6 engine performance deterioration: Evaluation of engine S/N 451-380

The performance testing and analytical teardown of CF6-6D engine serial number 451-380 which was recently removed from a DC-10 aircraft is summarized. The investigative test program was conducted inbound prior to normal overhaul/refurbishment. The performance testing included an inbound test, a test following cleaning of the low pressure turbine airfoils, and a final test after leading edge rework and cleaning the stage one fan blades. The analytical teardown consisted of detailed disassembly inspection measurements and airfoil surface finish checks of the as-received deteriorated hardware. Aspects discussed include the analysis of the test cell performance data, a complete analytical teardown report with a detailed description of all observed hardware distress, and an analytical assessment of the performance loss (deterioration) relating measured hardware conditions to losses in both specific fuel comsumption and exhaust gas temperature.

Kramer, W. H.↗
NASA NTRS1978

User's manual: Subsonic/supersonic advanced panel pilot code

Sufficient instructions for running the subsonic/supersonic advanced panel pilot code were developed. This software was developed as a vehicle for numerical experimentation and it should not be construed to represent a finished production program. The pilot code is based on a higher order panel method using linearly varying source and quadratically varying doublet distributions for computing both linearized supersonic and subsonic flow over arbitrary wings and bodies. This user's manual contains complete input and output descriptions. A brief description of the method is given as well as practical instructions for proper configurations modeling. Computed results are also included to demonstrate some of the capabilities of the pilot code. The computer program is written in FORTRAN IV for the SCOPE 3.4.4 operations system of the Ames CDC 7600 computer. The program uses overlay structure and thirteen disk files, and it requires approximately 132000 (Octal) central memory words.

Moran, J.↗
NASA NTRS1978

Thermal design and development of a planetary probe - Pioneer Venus large probe

The thermal control system developed for the Large Atmospheric Probe of the Pioneer Venus Multiprobe Mission is described. The scope of the thermal control task requires maintaining the probe internal equipment shelf temperatures within a nonoperating range of -40 to 122 F and an operating range of -4 to 122 F during three different mission phases: (1) preseparation, the transit phase of the mission when the probe is attached to the Multiprobe Spacecraft Bus, (2) postseparation, the free-flight cruise phase of the mission following release from the Bus, and (3) descent, the phase of the mission from preentry equipment turn-on to impact on the Venus surface. Thermal control for these phases is achieved by a combination of passive thermal finishes on the probe exterior surfaces and heaters mounted on the equipment shelves. Verification of the adequacy of the total thermal design to meet all mission requirements has been completed.

Hennis, L. A.↗
NASA NTRS1978

Design, analysis, fabrication and test of the Space Shuttle solid rocket booster motor case

The motor case used in the solid propellant booster for the Space Shuttle is unique in many respects, most of which are indigenous to size and special design requirements. The evolution of the case design from initial requirements to finished product is discussed, with increased emphasis of reuse capability, special design features, fracture mechanics and corrosion control. Case fabrication history and the resulting procedure are briefly reviewed with respect to material development, processing techniques and special problem areas. Case assembly, behavior and performance during the DM-1 static firing are reviewed, with appropriate comments and conclusions.

Kapp, J. R.↗
NASA NTRS1979

Quality control during IC processing

Manual gives detailed test procedures for controlling silicon-wafer processing in manufacture of integrated circuits. Included among 43 test procedures are: ionic, bacterial, and solids contamination of high-purity water needed for wafer processing; crystallographic reflection, purity, and orientation; substrate dimensions and finish; thickness of deposited epitaxial films; oxide quality; photoresist characteristics; pinholes in insulating layers; metallized adhesion; and quality of ohmic contact.

Source record↗
NASA NTRS1980

Repairing sealing surfaces on aluminum castings

Approach using stylus nickel plating instead of copper and cadmium plating has simplified repair procedure. Damaged sealing surfaces are stylus nickelplated in one step. Superficial scratches and porous areas are removed more easily from repaired surface by simply lapping sealing areas to required finish. Although method is aimed for aerospace components, it may be easily incorporated into conventional aluminumcasting technology. One-step repair can be considered for cast-aluminum automobile and aircraft engines to reduce time and costs.

Hanna, T. L.↗
NASA NTRS1980

Protecting brazing furnaces from air leaks

Inexpensive inert-atmosphere shielding protects vacuum brazing-furnace components that are likely to spring leak. Pipefittings, gages, and valves are encased in transparent plastic shroud inflated with argon. If leak develops, harmless argon will enter vacuum chamber, making it possible to finish ongoing brazing or heat treatment before shutting down for repair.

Armenoff, C. T.↗
NASA NTRS1978

Mini-BRU/BIPS foil bearing development

The analysis revealed the failure agent to be a combination of poor teflon coating adhesion, a decrease in bearing sway space and, possibly, lack of flushing flow through the bearing. A change in Teflon coating vendors provided substantially improved coating quality and surface finish. The sway space was increased and the cooling bleed flow was adjusted to flush the bearing. These changes were included in a test conducted in the WHL from 6 April to 22 May 1978 which resulted in the completion of 1006.9 hours of operation at temperature and load. Post-test inspection revealed the bearings to be in excellent condition and capable of completing a much longer test.

Dobler, F. X.↗
NASA NTRS1978

Model fire tests on polyphosphazene rubber and polyvinyl chloride (PVC)/nitrile rubber foams

A video tape record of model room fire tests was shown, comparing polyphosphazene (P-N) rubber and polyvinyl chloride (PVC)/nitrile rubber closed-cell foams as interior finish thermal insulation under conditions directly translatable to an actual fire situation. Flashover did not occur with the P-N foam and only moderate amounts of low density smoke were formed, whereas with the PVC/nitrile foam, flashover occurred quickly and large volumes of high density smoke were emitted. The P-N foam was produced in a pilot plant under carefully controlled conditions. The PVC/nitrile foam was a commercial product. A major phase of the overall program involved fire tests on P-N open-cell foam cushioning.

Widenor, W. M.↗