Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fatigue loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Thermomechanical and isothermal fatigue behavior of a (90)sub 8 titanium matrix composite

An experimental investigation was conducted to analyze the fatigue damage mechanisms operative in a 35 fiber volume percent (90 deg) titanium matrix composite (TMC) under 427 C isothermal and thermomechanical loading conditions. The thermomechanical fatigue (TMF) tests were performed with a temperature cycle from 200 to 427 C under closely controlled conditions to define both the deformation and fatigue life behavior. Degradation of the TMC's isothermal elastic moduli and coefficient of thermal expansion were monitored throughout the TMF tests. The results indicated TMF life trends which contrasted those established in a comparable (0 deg) system, as TMF loading of the (90 deg) TMC was not found to be 'life-limiting' in comparison to maximum temperature isothermal conditions. In-phase lives were very similar to those established under 427 C isothermal conditions. High stress isothermal fatigue at 427 C produced increased strain ratchetting and stiffness degradation relative to TMF conditions. Out-of-phase loadings produced TMF lives approximately an order of magnitude greater than the lives determined under isothermal and in-phase conditions. Extensive fractography and metallography were also performed. Two key issues were identified and appeared to dominate the fatigue damage and life of the (90 deg) TMC, namely, the weak fiber/matrix interface and environmental attack of the fiber/matrix interface via the exposed (90 deg) fiber ends.

Castelli, Michael G.↗
NASA NTRS2026

Mechanical Design and Operation of a Novel Lunar Environment Structural Test Rig (LESTR)

The Lunar Environment Structural Test Rig (LESTR) was developed to address a critical gap in mechanical property data for metal alloy wire materials under lunar-relevant conditions down to 40 K. Conventional aerospace material databases provide thermophysical properties for bulk metals over a wide temperature range, but validated mechanical and physical property data below 77 K, particularly for small-diameter wires, remain limited and are generally the exception rather than the rule. These conditions are essential for Artemis mission hardware such as shape memory alloy (SMA) rover tires. LESTR’s design requirements were to combine a high-stiffness electrodynamic load frame with closed- cycle cryogenic cooling, high-vacuum capability (10–6 torr), and noncontact optical strain measurement to enable tensile, four-point bend, and fatigue testing of wires or other materials and geometries at temperatures from 40 to 125 K. These considerable requirements were merged with the need to lower the barrier of testing for the end user as measured in terms of cost-per-test cycle, safety improvement, and reduction in upkeep costs associated with state-of-the-art solutions associated with cryomechanical material characterization. The system incorporates modular gripping and alignment fixtures; precision thermal management using cryocoolers and embedded heaters; and integrated instrumentation for displacement, load, temperature, and vacuum control. Calibration procedures establish correlations between tooling and specimen temperature, ensuring accurate thermal conditions across the design envelope unbound by cryofluid conditions in heritage immersion-based test systems. Initial validation tests using Inconel (Special Metals Corp.) wire demonstrated accurate ultimate strength and post-yield behavior. The load frame operation was also verified under representative service conditions, including thermal cycling and prolonged fatigue loading. By generating mechanical property data at ultralow temperatures, LESTR fills a critical gap in existing materials databases and provides a scalable platform for iterative alloy development and durability assessment for planetary hardware. This capability supports NASA’s long-term objectives for surface exploration by enabling design confidence for components operating in extreme cryogenic environments.

LESTR↗
NASA NTRS1976

Structural analysis of wind turbine rotors for NSF-NASA Mod-0 wind power system

Preliminary estimates are presented of vibratory loads and stresses in hingeless and teetering rotors for the proposed NSF-NASA Mod-0 wind power system. Preliminary blade design utilizes a tapered tubular aluminum spar which supports nonstructural aluminum ribs and skin and is joined to the rotor hub by a steel shank tube. Stresses in the shank of the blade are calculated for static, rated, and overload operating conditions. Blade vibrations were limited to the fundamental flapping modes, which were elastic cantilever bending for hingeless rotor blades and rigid-body rotation for teetering rotor blades. The MOSTAB-C computer code was used to calculate aerodynamic and mechanical loads. The teetering rotor has substantial advantages over the hingeless rotor with respect to shank stresses, fatigue life, and tower loading. The hingeless rotor analyzed does not appear to be structurally stable during overloads.

Spera, D. A.↗
NASA NTRS1988

The growth of small cracks in 4340 steel

A semiempirical crack-growth model incorporating crack-closure effects has been used to predict crack growth rates and total fatigue life in notched specimens of 4340 steel having an initial defect typical of those previously noted in this steel upon subjection to both constant-amplitude and spectrum loadings. Model predictions for fatigue life are found to be in reasonable agreement with experiments and, in particular, the model was able to accurately predict total fatigue life for specimens subjected to the 'Felix/28' spectrum loading sequence on the sole basis of constant-amplitude test test results.

Swain, M. H.↗
NASA NTRS1996

Control of Thermal Deflection, Panel Flutter and Acoustic Fatigue at Elevated Temperatures Using Shape Memory Alloys

The High Speed Civil Transport (HSCT) will have to be designed to withstand high aerodynamic load at supersonic speeds (panel flutter) and high acoustic load (acoustic or sonic fatigue) due to fluctuating boundary layer or jet engine acoustic pressure. The thermal deflection of the skin panels will also alter the vehicle's configuration, thus it may affect the aerodynamic characteristics of the vehicle and lead to poor performance. Shape memory alloys (SMA) have an unique ability to recover large strains completely when the alloy is heated above the characteristic transformation (austenite finish T(sub f)) temperature. The recovery stress and elastic modulus are both temperature dependent, and the recovery stress also depends on the initial strain. An innovative concept is to utilize the recovery stress by embedding the initially strained SMA wire in a graphite/epoxy composite laminated panel. The SMA wires are thus restrained and large inplane forces are induced in the panel at elevated temeperatures. By embedding SMA in composite panel, the panel becomes much stiffer at elevated temperatures. That is because the large tensile inplane forces induced in the panel from the SMA recovery stress. A stiffer panel would certainly yield smaller dynamic responses.

Mei, Chuh↗
NASA NTRS1980

Analysis and test of bonded single lap joints with preformed adherends

A theoretical and experimental study has been conducted to investigate the load transfer of a single lap joint where the adherends have been preformed so that the angle between the line of action of the applied in-plane force and the bond line is reduced. The preforming of the adherend reduces the moment resultant in the adherend at the edge of the overlap region which reduces both the maximum peel and shear stresses in the adhesive, and gives a more uniform shear distribution in the adhesive. An increase in static load transfer of up to 120 percent has been shown, and several orders of magnitude increase in fatigue life have been achieved with modest preform angles. Thus, sizeable benefits can be obtained in the fatigue life or additional load capacity of bonded single lap joints by preforming the adherends.

Sawyer, J. W.↗
NASA NTRS1994

Fatigue life and crack growth prediction methodology

This paper reviews the capabilities of a plasticity-induced crack-closure model and life-prediction code to predict fatigue crack growth and fatigue lives of metallic materials. Crack-tip constraint factors, to account for three-dimensional effects, were selected to correlate large-crack growth rate data as a function of the effective stress-intensity factor range (Delta K(sub eff)) under constant amplitude loading. Some modifications to the Delta K(sub eff)-rate relations were needed in the near threshold regime to fit small-crackgrowth rate behavior and endurance limits. The model was then used to calculate small- and large-crack growth rates, and in some cases total fatigue lives, for several aluminum and titanium alloys under constant-amplitude, variable-amplitude, and spectrum loading. Fatigue lives were calculated using the crack-growth relations and microstructural features like those that initiated cracks. Results from the tests and analyses agreed well.

Newman, J. C., Jr.↗
NASA NTRS1983

Load sequence effects on graphite/epoxy /+, -35/2s laminates

Load sequence effects on composite material fatigue behavior are due to the difference in residual strength when fatigue occurs, or the 'boundary effect', and the 'material money effect' due to previous loads. The present model, which allows the isolation of the effects of memory from those of boundary, has been investigated through a test program for the case of /+, -35/2s graphite/epoxy laminates under high-low and low-high load sequences which generated statistical residual strength data. As predicted by the model, the memory effect is present and a good correlation is obtained between test results and the theoretical predictions for both median residual strength and the expected percentage of fatigue failures under dual loading. It is noted, however, that the statistical dispersion of the residual strength test results is much smaller than that of the static ultimate strength.

Yang, J. N.↗
NASA NTRS1993

Fatigue life and crack growth prediction methodology

The capabilities of a plasticity-induced crack-closure model and life-prediction code to predict fatigue crack growth and fatigue lives of metallic materials are reviewed. Crack-tip constraint factors, to account for three-dimensional effects, were selected to correlate large-crack growth rate data as a function of the effective-stress-intensity factor range (delta(K(sub eff))) under constant-amplitude loading. Some modifications to the delta(K(sub eff))-rate relations were needed in the near threshold regime to fit small-crack growth rate behavior and endurance limits. The model was then used to calculate small- and large-crack growth rates, and in some cases total fatigue lives, for several aluminum and titanium alloys under constant-amplitude, variable-amplitude, and spectrum loading. Fatigue lives were calculated using the crack growth relations and microstructural features like those that initiated cracks. Results from the tests and analyses agreed well.

Newman, J. C., Jr.↗
NASA NTRS1986

Fatigue of 1018 steel in hydrogen

Tests are performed at different hydrogen pressures and mechanical load parameter values (applied load, stress concentration factor, applied load frequency) to study enhanced fatigue crack growth in SAE 1018 steel. Oxygen was introduced as a hydrogen-oxygen gas mixture environment in order to compare the role of oxygen in crack inhibition with that previously reported for both static and cyclic loading of higher strength steels. In a number of experiments, a thin film of palladium was applied to the specimen surface to facilitate the study of steel-hydrogen interaction in the absence of any surface impedance to hydrogen entry. The kinetics of the diffusing atoms are found to be influenced by the stress field around the notch tip and the applied frequency. An increment in environmental effect occurred when applied load or stress concentration factor was increased.

Lo, S. H.↗
NASA NTRS1981

Fatigue retardation due to creep in a fibrous composite

Experiments performed to determine the effects of temperature and creep strain on the fatigue life of a graphite/epoxy composite laminate show that (1) sustained periods of static loading have significant retardation effects on the fatigue degradation rate of the laminated composite, and (2) cyclic loading with a lower frequency preceding higher frequency loading also prolongs the fatigue life. A creep crack hypothesis is proposed that can provide reasonable interpretations for these experimental results.

Sun, C. T.↗
NASA NTRS1985

Interaction of High-cycle and Low-cycle Fatigue of Haynes 188 Alloy at 1400 F Deg

The interaction of low-cycle fatigue (LCF) and high-cycle fatigue (HCF) was evaluated at the NASA Lewis Research Center on Haynes 188 alloy at 1400 F. Completely reversed, axial-load, strain-controlled fatigue tests were performed to determine the baseline data for this study. Additional specimens for interaction tests were cycled first at a high strain range for various small portions of expected LCF life followed by a step change to a low strain range to failure in HCF. Failure was defined as complete specimen separation. The resultant lives varied between 10 and 5000 cycles for the low-cycle fatigue tests and between 4500 and 3 million for the high-cycle fatigue tests. For the interaction tests the low-cycle-life portion ranged from 30 and 1000 applied cycles while the high-frequency life ranged from 300 and 300,000 cycles to failure. The step change results showed a significant nonlinear interaction in expected life. Application of a small part of the LCF life drastically decreased the available HCF life as compared with what would have been expected by the classical linear damage rule (LDR).

Peter T Bizon↗
NASA NTRS1972

Aspect of cumulative fatigue damage under multiaxial strain cycling.

The concept of order of loading and its effect on cumulative fatigue damage under multiaxial strain cyclings was investigated. The effect is illustrated through nonlinear relationships between biaxial fatigue damage and cycle-ratio diagrams. Uniaxial theories such as Miner's method, the convergence method, and the double linear damage rule in its special and generalized form, were examined and extended to the biaxial case through the octahedral shear strain theory. The generalized double linear damage rule was found more applicable to biaxial cumulative fatigue damage.

Zamrik, S. Y.↗
NASA NTRS1992

Effects of constraint on crack growth under aircraft spectrum loading

The objective is to study the effects of constraint on fatigue crack growth under aircraft spectrum loading. A plasticity-induced crack-closure model that accounts for constraint variations during the transition from flat-to-slant crack growth was used to correlate crack-growth rate data under constant-amplitude loading and to calculate crack growth under simulated aircraft spectrum loading. The model was applied to several thin-sheet aluminum alloy materials. Under laboratory air conditions, the transition was shown to be related to the size of the cyclic plastic zone based on the effective stress-intensity factor range for several sheet materials and thicknesses. Results from three-dimensional, elastic-plastic, finite-element analyses of a flat, straight-through crack in a thin-sheet aluminum alloy specimen showed a constraint loss similar to that assumed in the model. Using test data and the closure model, the location of the constraint-loss regime in terms of growth rate and the value of the constraint factor at these rates were determined by trial and error. The model was then used to calculate crack growth under the TWIST spectrum. The calculated results agreed reasonably well with test data. In general, the model predicted shorter crack-growth lives than tests under the TWIST spectrum by about 40 percent. For the TWIST spectrum clipped at Level 3, the calculated lives were within about 20 percent. The results demonstrated that constraint variations, especially for thin-sheet alloys, should be accounted for to predict crack growth under typical aircraft spectra.

Newman, J. C., Jr.↗
NASA NTRS1985

Closure measurements on short fatigue cracks

Single-edged notched specimens, 2.3 mm thick, of 2024-T3 aluminum were cyclicly loaded at R-ratios of 0.5, 0.0, -1.0 and -2.0. The notch roots were periodically inspected with an optical microscope to locate the initiation of very short cracks. Acetate replicas were also taken. The loads were selected to produce fatigue lives of 500,000 cycles or less. Crack opening displacements were measured at single positions across cracks as short as 0.035 mm and as long as the full thickness of the specimen. The opening load ratios for the short cracks are somewhat smaller than for long cracks at positive R-ratios, but are considerably smaller for negative R-ratios.

Lee, J. J.↗
NASA NTRS1988

Closure measurements on short fatigue cracks

Single-edged notched specimens, 2.3 mm thick, of 2024-T3 aluminum were cyclically loaded at R-ratios of 0.5, 0.0, -1.0, and -2.0. The notch roots were periodically inspected with an optical microscope to locate the initiation of very short cracks. Acetate replicas were also taken. The loads were selected to produce fatigue lives of 500,000 cycles or less. Crack opening displacements were measured at single positions across cracks as short as 0.035 mm and as long as the full thickness of the specimen. The opening load ratios for the short cracks are somewhat smaller than for long cracks at positive R-ratios, but are considerably smaller for negative R-ratios.

Lee, Joo-Jin↗