Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Estimate of pre-thermal quench non-thermal electron density profile during Ar pellet shutdowns of low-density target plasmas in DIII-D

The radial density profile of pre-thermal quench (pre-TQ) early-time runaway electrons (REs) is estimated by combining electron cyclotron emission (ECE) and soft x-ray (SXR) data during rapid shutdown of low-density (n e ≲ 10 13 cm -3 ) DIII-D target plasmas with cryogenic argon pellet injection. This technique is limited in these experiments to the pre-TQ phase and quickly loses validity during the TQ. Two different cases are studied: a high (10 keV) temperature target and a lower (4 keV) temperature target. The results indicate that early-time, low-energy (~10 keV) REs form ahead of the argon pellet as it enters the plasma, affecting the pellet ablation rate; it is hypothesized that this may be caused by rapid cross-field transport of argon ions ahead of the pellet. Fokker-Planck modeling of the two shots suggests that the RE current is quite significant during the pre-TQ phase (up to 50% of the total current). Comparison between modeled pre-TQ RE current and post-TQ RE current inferred from avalanche theory suggests that RE current increases during the high temperature target TQ but decreases during the low temperature target TQ. Here, the uncertainties in this estimate are large; but, if true, this suggests that TQ loss of REs can be larger than previously estimated in DIII-D.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Doppler noise considered as a function of the signal path integration of electron density

The hypothesis is advanced that observed Doppler noise during solar conjunctions is proportional to total columnar electron content along the signal path. This assumption leads directly to a geometrical model (ISED) for observed Doppler noise which is shown to be in very good agreement with Doppler noise data accumulated during the 1975 Pioneer 10, Pioneer 11 and Helios 1 solar conjunctions. An augmented model is constructed which quantitatively indicates correlation between earth observed sunspot activity and systematic, cyclical deviations from the ISED model.

Berman, A. L.↗

Platinum-like HER onset in a GNR/MoS 2 quantum dot heterostructure through curvature-dependent electron density reconfiguration

Tailoring the curvature-directed lattice strain in GNRs along with optimal surface anchoring of molybdenum disulfide (MoS 2 ) quantum dots (QDs) can lead to a unique heterostructure with Pt-like HER activity (onset potential –60 mV). The curvature-induced electronic charge redistribution at the curved region in the graphene nanoribbons allows a facile GNR-MoS 2 interfacial charge transfer in the heterostructure, making the interfacial sulfur (S) more active towards the HER. Finally, the density functional theory (DFT) calculations confirmed electronically activated interfacial S-based catalytic centers in the curved GNR-based heterostructure leading to Pt-like HER activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

F region electron density irregularity spectra near auroral acceleration and shear regions

Two orbits of the Atmosphere Explorer D yielded data on F region electron irregularities in the high latitude ionosphere. Data were taken with a retarding potential analyzer, an ion drift meter, a low energy electron experiment and a photoelectron spectrometer. Auroral forms were simultaneously visually sighted by DMSP spacecraft. The irregularities were associated with auroral excitation and large structured flow regions. Steep spectra with one-dimensional spectral index values for wavelengths over 1 km were observed in the acceleration region. Large amplitude irregularities appeared in large structured flow regions and displayed shallow spectra, indicating the presence of large power spectral densities at scale lengths of about 100 m. It is suspected that large velocities or shears in the velocities in adjacent precipitation regions cause the F region density perturbations.

Basu, S.↗

Magnetospheric electron density measurements from upper hybrid resonance noise observed by IMP-6

A band of natural radio noise between the local electron plasma frequency and the upper hybrid resonance frequency is observed by the IMP-6 satellite. The band exists over a large range of geocentric radial distances extending from inside the plasmapause boundary to greater than 10 earth radii in the outer magnetosphere. The center frequency of the noise band decreases with increasing radial distance, and changes abruptly at the plasmapause boundary. The broadband electric field strength of this noise is very small, seldom exceeding 10 microvolts/meter, and probably could not be detected without using long electric antennas of IMP-6. It is believed that this noise is produced by incoherent Cerenkov emission from super-thermal electrons. In some cases a second very narrow noise band was observed at a frequency slightly above the second harmonic of the electron gyrofrequency.

Shaw, R. R.↗

SCEMA: a high channel density electronics module for fast waveform capture

The development of fast, highly pixelated photodetectors with single-photon sensitivity has the potential to enable a variety of new radiation detection concepts. Systems that desire to employ these detectors without loss of information demand waveform digitization with high sampling rates. Switched capacitor arrays provide a low-cost, low-power, compact solution to fast readout with high channel density. The Sandia Laboratories Compact Electronics for Modular Acquisition (SCEMA) was developed to meet these demands. A single module employs two domino ring sampling switched capacitor arrays (DRS4) [1] to provide 16 channels of up to 5 GS/s waveform digitization. This paper presents an overview of the board design and function. Calibration procedures for the module are discussed. Lastly, temporal resolution tests are presented demonstrating the module's viability as readout for high fidelity temporal measurements of single photons in suitable photodetectors.

47 OTHER INSTRUMENTATION↗

Electron density dependence of impedance probe plasma potential measurements

In earlier works, we used spheres of various sizes as impedance probes in demonstrating a method of determining plasma potential, φ{sub p}, when the probe radius is much larger than the Debye length, λ{sub D}. The basis of the method in those works [Walker et al., Phys. Plasmas 13, 032108 (2006); ibid. 15, 123506 (2008); ibid. 17, 113503 (2010)] relies on applying a small amplitude signal of fixed frequency to a probe in a plasma and, through network analyzer-based measurements, determining the complex reflection coefficient, Γ, for varying probe bias, V{sub b}. The frequency range of the applied signal is restricted to avoid sheath resonant effects and ion contributions such that ω{sub pi} ≪ ω ≪ ω{sub pe}, where ω{sub pi} is the ion plasma frequency and ω{sub pe} is the electron plasma frequency. For a given frequency and applied bias, both Re(Z{sub ac}) and Im(Z{sub ac}) are available from Γ. When Re(Z{sub ac}) is plotted versus V{sub b}, a minimum predicted by theory occurs at φ{sub p} [Walker et al., Phys. Plasmas 17, 113503 (2010)]. In addition, Im(Z{sub ac}) appears at, or very near, a maximum at φ{sub p}. As n{sub e} decreases and the sheath expands, the minimum becomes harder to discern. The purpose of this work is to demonstrate that when using network analyzer-based measurements, Γ itself and Im(Z{sub ac}) and their derivatives are useful as accompanying indicators to Re(Z{sub ac}) in these difficult cases. We note the difficulties encountered by the most commonly used plasma diagnostic, the Langmuir probe. Spherical probe data is mainly used in this work, although we present limited data for a cylinder and a disk. To demonstrate the effect of lowered density as a function of probe geometry, we compare the cylinder and disk using only the indicator Re(Z{sub ac})

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Kilometer-sized waves in electron density in the Venusian nightside ionosphere

As periapsis of the Pioneer Venus Orbiter (PVO) descended into the lower nightside ionosphere of Venus in the Fall of 1992, wave-like ionospheric density strucutures began to appear on some of the volt-ampere characteristics of the Orbiter Electron Temperature Probe. The number of such events is insufficient to fully define their morphology but enough to provide an indication of the wave amplitudes, scale sizes, occurrence altitudes, and local time variation. The density variations were quasi-sinudoidal, with wavelengths of the order of 1 km along the nearly horizontal trajectory near periapsis. Nearly all of the wave events were encountered within an altitude band lying between 140 and 160 km, a region containing the steep negative N(sub e) gradient just above the ionospheric peak. The waves generally did not fill the occurrence band but were seen primarily as isolated events on curves taken intermittently as PVO crossed through the band. Peak-to-trough amplitudes (delta N/N) were in the range of 5% to 50%. The latitudinal extent of the waves could not be resolved because volt-ampere curves were obtained only intermittent, however, their occurrence on both inbound and outbound passages through the wave band suggests that the waves sometimes exist in layers that extend over at least 15 deg of latitude. The generation mechanism for these waves is unknown, but we suspect that it involves the steep density gradient that separates the main nightside ionosphere from the tenuous, and probably rapidly flowing plasma above.

Brace, Larry H.↗

Kilometer-Sized Waves in Electron Density in the Venusian Nightside Ionosphere

As periapsis of the Pioneer Venus Orbiter (PVO) descended into the lower nightside ionosphere of Venus in the Fall of 1992, wave-like ionospheric density structures began to appear on some of the volt-ampere characteristics of the Orbiter Electron Temperature Probe. The number of such events is insufficient to fully define their morphology but enough to provide an indication of the wave amplitudes, scale sizes, occurrence altitudes, and local time variation. The density variations were quasi-sinusoidal, with wavelengths of the order of 1 km along the nearly horizontal trajectory near periapsis. Nearly all of the wave events were encountered within an altitude band lying between 140 and 160 km, a region containing the steep negative N(sub e) gradient just above the ionospheric peak. The waves generally did not fill the occurrence band but were seen primarily as isolated events on curves taken intermittently as PVO crossed through the band. Peak-to-trough amplitudes ((Delta)N/N) were in the range of 5% to 50%. The waves exhibited little local time variation within the available viewing period (01-04 hrs), with perhaps a tendency for the waves to rise to slightly higher altitudes toward dawn. The latitudinal extent of the waves could not be resolved because volt-ampere curves were obtained only intermittently, however, their occurrence on both inbound and outbound passages through the wave band suggests that the waves sometimes exist in layers that extend over at least 15 deg of latitude. The generation mechanism for these waves is unknown, but we suspect that it involves the steep density gradient that separates the main nightside ionosphere from the tenuous, and probably rapidly flowing plasma above.

Brace, Larry H.↗

Analysis of correlations between intrinsic ductility and electronic density of states in refractory alloys

High entropy alloys (HEAs) correspond to a new and emerging class of materials that allows us to explore a large composition space to tune mechanical strength and thermal stability. Therefore, to design better alloys, it is important to scan the high-dimensional space of chemistry, composition and temperature. Here, to facilitate this search, we present a method to screen intrinsically ductile body centered cubic (BCC) refractory alloys from electronic structure calculations by using the density of states (DOS) at the Fermi level, g(μ F ). This correlation between intrinsic ductility and g(μ F ) is tested by analyzing group V (V, Nb, Ta) and VI (Mo, W) refractory metals, binary alloys, such as W-Nb, W-V, Mo-Nb and Mo-V, and refractory alloys for which experimental stress-strain measurements are available. In addition, we perform a high-throughput exploration of the entire composition space of a recently proposed alloy system, CrMoNbV, and identify compositions that exhibit high intrinsic ductility.

36 MATERIALS SCIENCE↗

Gas pressure and electron density at the level of the active zone of hollow cathode arc discharges

A model for the longitudinal variations of the partial pressures of electrons, ions, and neutral particles is proposed as a result of an experimental study of pressure variations at the level of the active zone as a function of the various discharge parameters of a hollow cathode arc. The cathode region where the temperature passes through its maximum is called active zone. The proposed model embodies the very important variations which the partial electron and neutral particles pressures undergo at the level of the active zone.

Minoo, M. H.↗

Multipole Expansion of Atomic Electron Density Fluctuation Interactions in the Density-Functional Tight-Binding Method

The accuracy of the density-functional tight-binding (DFTB) method in describing noncovalent interactions is limited due to its reliance on monopole-based spherical charge densities. In this study, we present a multipole-extended second-order DFTB (mDFTB2) method that takes into account atomic dipole and quadrupole interactions. Furthermore, we combine the multipole expansion with the monopole-based third-order contribution, resulting in the mDFTB3 method. To assess the accuracy of mDFTB2 and mDFTB3, we evaluate their performance in describing noncovalent interactions, proton transfer barriers, and dipole moments. Here, our benchmark results show promising improvements even when using the existing electronic parameters optimized for the original DFTB3 model. Both mDFTB2 and mDFTB3 outperform their monopole-based counterparts, DFTB2 and DFTB3, in terms of accuracy. While mDFTB2 and mDFTB3 perform comparably for neutral and positively charged systems, mDFTB3 exhibits superior performance over mDFTB2 when dealing with negatively charged systems and proton transfers. Overall, the incorporation of the multipole expansion significantly enhances the accuracy of the DFTB method in describing noncovalent interactions and proton transfers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the properties of Au2₂P₃ z (z = -1, 0, +1): analysis of geometry, interaction, and electron density

Au₂P₃, the only metastable binary phase of gold phosphide, has been discovered to exhibit remarkable semiconductor properties among metal phosphides. A systematic study on the geometry, the transformation of Au₂P₃ into different valence states and the different interactions among the atoms of the species is performed by using the density functional theory (DFT) method. The global minimum of Au₂P₃- is a 3D structure with C s symmetry. This structure could be distorted from a planar configuration of Au₂P₃ which decreases the steric effect on it and leads to a new stable configuration. An analogous planar configuration, a local minimum rather than a global minimum, is also found in Au₂P₃⁺, due to the electron effect acting on the structure. Natural bond orbital (NBO) analysis reveals the re-distribution progression of the charge within the species. The central located Au atom and another no. 5 positioned P atom play significant roles on the structures. P5, as an electron adjuster, balances the electron distribution at different valence states of the structures. Deformation density analysis supplies information about charge transfer and the bonding type between two adjacent atoms as well. Looking deep into the bonding types, as electron localization function (ELF) suggests, the interaction between two adjacent P atoms (P3 and P4) of Au₂P₃ belongs to a strong covalent bond. The Au–P interactions among the configurations could be classified as weak classical covalent bonds through the atoms in molecules (AIM) dual parameter analysis. And for the first time, the weak interaction between the two adjacent Au atoms (Au1 and Au2) of the charged states of Au₂P₃ (Au₂P₃⁻ and Au₂P₃⁺), are verified and different from the neutral Au₂P₃ through the reduced density gradient (RDG) analysis.

Environmental Molecular Sciences Laboratory↗

Discussion of the reliability of electron densities and energies interpreted from data and limits on the proton energy and density

Analysis of radio observations of Jupiter were changed to take into account the antenna resolution. A dipole magnetic field with a surface equatorial value of 7 gauss is assumed. The electron temperature is found to increase for r 2.5 Jupiter radii with decreasing r as 1/r cubed, reaching a peak of about 100 MeV at r = 2.5 Jupiter radii. For r 2.5 Jupiter radii, the electron temperature goes as r to the 6th power because of energy lost to radiation. The consequences of making an upper estimate on the proton flux by assuming the magnetic field is loaded with all the energetic protons it can hold are described. The upper limits of proton energy, density, flux, and energy flux are calculated for 1, 2, 2.5, 3, and 6 Jupiter radii. The proton energy and velocity estimates are considered to be fairly reliable; the upper limit to the number density is probably much higher than actuality.

Beard, D. B.↗

Impact of electron density on the fixed-node errors in Quantum Monte Carlo of atomic systems

We analyze the effect of increasing charge density on the fixed-node errors in diffusion Monte Carlo (FNDMC). We compare FNDMC ground state energies of 4-electron atomic systems with nuclear charge using Hartree–Fock and restricted Configuration Interaction trial wave functions. We perform these calculations for several different values of the nuclear charge, and we analyze the systematic trends of the recovered correlation energies as a function of . For this testing system we demonstrate that the fixed-node error of the Hartree–Fock trial wave functions increases linearly with increasing the nuclear charge.

Chemistry↗

Performance of a local electron density trigger to select extensive air showers at sea level

Time coincident voltage pulses in the two closely space (1.6m) plastic scintillators were recorded. Most of the recorded events are expeted to be due to electrons in cosmic ray showers whose core fall at some distance from the detectors. This result is confirmed from a measurement of the frequency distribution of the recorded density ratios of the two scintillators.

Abbas, T.↗

Vertical distribution of vibrational energy of molecular nitrogen in a stable auroral red arc and its effect on ionospheric electron densities

Previous solutions of the problem of the distribution of vibrationally excited molecular nitrogen in the thermosphere have either assumed a Boltzmann distribution and considered diffusion as one of the loss processes or solved for the energy level populations and neglected diffusion. Both of the previous approaches are combined by solving the time dependent continuity equations, including the diffusion process, for the first six energy levels of molecular nitrogen for conditions in the thermosphere corresponding to a stable auroral red arc. The primary source of molecular nitrogen excitation was subexcitation, and inelastic collisions between thermal electrons and molecular nitrogen. The reaction rates for this process were calculated from published cross section calculations. The loss processes for vibrational energy were electron and atomic oxygen quenching and vibrational energy exchange. The coupled sets of nonlinear, partial differential equations were solved numerically by employing finite difference equations.

Newton, G. P.↗