Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Extension of constrained incremental Newton-Raphson scheme to generalized loading fields

This paper develops numerical strategies which enable the constrained incremental Newton-Raphson scheme to handle the static response of structure to loading fields with completely generalized histories. This is made possible through the use of specially warped hyperelliptic constraint surfaces which control successive or clustered load steps in the vicinity of loading events with specific timing schedules. Such an approach enables improved convergence and stability characteristics. Due to the generality of the methodology, pre- and postbuckling behavior caused by both kinematic and material nonlinearity can be handled. To demonstrate the scheme, the results of several bench-mark problems are also presented. These include situations involving nonlinear kinematics as well as highly history-dependent elastic-plastic and thermoelastic-plastic material behavior.

Padovan, J.↗
DOE OSTI2022

An Eulerian crystal plasticity framework for modeling large anisotropic deformations in energetic materials under shocks

Here, this paper demonstrates a novel Eulerian computational framework for modeling anisotropic elastoplastic deformations of organic crystalline energetic materials (EM) under shocks. While Eulerian formulations are advantageous for handling large deformations, constitutive laws in such formulations have been limited to isotropic elastoplastic models, which may not fully capture the shock response of crystalline EM. The present Eulerian framework for high-strain rates, large deformation material dynamics of EM incorporates anisotropic isochoric elasticity via a hypo-elastic constitutive law and visco-plastic single-crystal models. The calculations are validated against atomistic calculations and experimental data and benchmarked against Lagrangian (finite element) crystal plasticity computations for shock-propagation in a monoclinic organic crystal, octahydro-1,3,5,7-tetranitro-1,3,5,7 tetrazocine (β-HMX). The Cauchy stress components and the resolved shear stresses calculated using the present Eulerian approach are shown to be in good agreement with the Lagrangian computations for different crystal orientations. The Eulerian framework is then used for computations of shock-induced inert void collapse in β-HMX to study the effects of crystal orientations on hotspot formation under different loading intensities. The computations show that the hotspot temperature distributions and the collapse profiles are sensitive to the crystal orientations at lower impact velocities (viz., 500 m/s); when the impact velocity is increased to 1000 m/s, the collapse is predominantly hydrodynamic and the role of anisotropy is modest. The present methodology will be useful to simulate energy localization in shocked porous energetic material microstructures and other situations where large deformations of single and polycrystals govern the thermomechanical response.

42 ENGINEERING↗
DOE OSTI2024

Materials data science using CRADLE: A distributed, data-centric approach

Abstract There is a paradigm shift towards data-centric AI, where model efficacy relies on quality, unified data. The common research analytics and data lifecycle environment (CRADLE™) is an infrastructure and framework that supports a data-centric paradigm and materials data science at scale through heterogeneous data management, elastic scaling, and accessible interfaces. We demonstrate CRADLE’s capabilities through five materials science studies: phase identification in X-ray diffraction, defect segmentation in X-ray computed tomography, polymer crystallization analysis in atomic force microscopy, feature extraction from additive manufacturing, and geospatial data fusion. CRADLE catalyzes scalable, reproducible insights to transform how data is captured, stored, and analyzed. Graphical abstract

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2000

Mesoscopic Nonlinear Elastic Modulus of Thermal Barrier Coatings Determined by Cylindrical Punch Indentation

Cylindrical punch indentations are performed to determine the effective modulus of a plasma-sprayed ZrO2-8Wt%Y2O3 thermal barrier coating (TBC) as a function of coating depth. Cylindrical punch indentations offer significant advantages over pointed (Vickers, Berkovich, or Knoop) indentations for materials that do not exhibit linear elastic behavior. Cyclic loading with a cylindrical punch clearly shows the TBCs to exhibit nonlinear elastic behavior with significant hysteresis that is related to the compaction and internal sliding within the plasma-spray splat microstructure. In addition, the effect of a high heat flux laser treatment was shown to produce a gradient both in the effective TBC modulus and degree of loading/unloading hysteresis with depth.

Eldridge, Jeffrey I.↗
NASA NTRS1993

On the design of structural components using materials with time-dependent properties

The application of the elastic-viscoelastic correspondence principle is presented as a design tool for structural design engineers for composite material applications. The classical problem of cantilever beams is used as the illustration problem. Both closed-form and approximate numerical solutions are presented for several different problems. The application of the collocation method is presented as a viable and simple design tool to determine the time-dependent behavior and response of viscoelastic composite beams under load.

Rodriguez, Pedro I.↗
DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

This project demonstrates a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique is used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that laser ultrasonics-based methodology developed in this work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A laser ultrasonics-based approach for rapid screening of high entropy alloys

The primary objective of this seed project is to develop a laser ultrasonics-based characterization methodology for rapid metallic materials design and discovery via in situ determination of phases, microstructures and elastic properties with respect to temperature. Ultrasonic waves are strongly affected by material microstructure, and therefore, serve as a facile means to probe elastic properties, phase content and their size distributions and volume fractions. In this study, a laser ultrasonic technique will be used to systematically study the evolution of properties in a set of interrelated simple binary alloys and high entropy alloys (HEA). Phase transformations and microstructural changes inferred from the ultrasonic signals will be correlated with electron microscopy data and predictions using calculations of phase diagrams (CALPHAD). The non-contact and non-destructive ultrasonic testing approach developed in this study could overcome several limitations associated with current material characterization methods for materials discovery. It is expected that the products of the proposed work will be utilized to evaluate novel graded composition HEAs currently being developed at the Idaho National Laboratory (INL) using advanced manufacturing methods based on direct energy deposition and spark plasma sintering processes, and contribute to accelerate the discovery of HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrasonic waves from radial mode excitation of a piezoelectric disc on the surface of an elastic solid

In this work, we discuss the ultrasonic wave propagation characteristics in an isotropic elastic solid due to the radial mode excitation of a piezoelectric disc actuator bonded to its surface. Finite element simulations using coupled electromechanical modeling is employed to investigate the wave propagation behavior. We find that the radial mode vibrations on the surface of the elastic solid generates all the three types of ultrasonic waves: longitudinal, shear, and surface waves. The waves in the solid are comprised of a central lobe and multiple side lobes based on the frequency of the radial mode excitation. The central lobe is predominantly composed of longitudinal waves and the side lobes are composed of shear waves. While the longitudinal waves have a strong central lobe and weak side lobes that are not fully developed, shear waves consists of fully developed side lobes. In addition, we observe that the longitudinal waves have fewer side lobes inside the solid compared to the shear waves. A semi-analytical approach is presented to explain the above observations. The interface traction boundary condition between the piezoelectric disc and the elastic solid is approximated as a truncated 'Bessel' excitation over the area of the piezoelectric disc in contact with the solid. A Fourier–Bessel series expansion technique is used to investigate the wave propagation behavior from the above traction boundary condition. The results obtained explain the observations from the finite element simulations with regard to the number and distribution of side lobes pertaining to the longitudinal and shear waves generated from the radial modes of the piezoelectric disc. The proposed semi-analytical approach is general and can be applied to any arbitrary axisymmetric excitations on the surface of an elastic solid.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Probabilistic Structural Analysis Methods (PSAM) for Select Space Propulsion System Components

Probabilistic Structural Analysis Methods (PSAM) are described for the probabilistic structural analysis of engine components for current and future space propulsion systems. Components for these systems are subjected to stochastic thermomechanical launch loads. Uncertainties or randomness also occurs in material properties, structural geometry, and boundary conditions. Material property stochasticity, such as in modulus of elasticity or yield strength, exists in every structure and is a consequence of variations in material composition and manufacturing processes. Procedures are outlined for computing the probabilistic structural response or reliability of the structural components. The response variables include static or dynamic deflections, strains, and stresses at one or several locations, natural frequencies, fatigue or creep life, etc. Sample cases illustrates how the PSAM methods and codes simulate input uncertainties and compute probabilistic response or reliability using a finite element model with probabilistic methods.

Source record↗
DOE OSTI2021

Inelastic peridynamic model for molecular crystal particles

The peridynamic theory of solid mechanics is applied to modeling the deformation and fracture of micrometer-sized particles made of organic crystalline material. A new peridynamic material model is proposed to reproduce the elastic–plastic response, creep, and fracture that are observed in experiments. The model is implemented in a three-dimensional, meshless Lagrangian simulation code. In the small deformation, elastic regime, the model agrees well with classical Hertzian contact analysis for a sphere compressed between rigid plates. Under higher load, material and geometrical nonlinearity is predicted, leading to fracture. Finally, the material parameters for the energetic material CL-20 are evaluated from nanoindentation test data on the cyclic compression and failure of micrometer-sized grains.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1990

Matrix density effects on the mechanical properties of SiC/RBSN composites

The room temperature mechanical properties were measured for SiC fiber reinforced reaction-bonded silicon nitride composites (SiC/RBSN) of different densities. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers (Textron SCS-6) in a reaction-bonded Si3N4 matrix. The composite density was varied by changing the consolidation pressure during RBSN processing and by hot isostatically pressing the SiC/RBSN composites. Results indicate that as the consolidation pressure was increased from 27 to 138 MPa, the average pore size of the nitrided composites decreased from 0.04 to 0.02 microns and the composite density increased from 2.07 to 2.45 gm/cc. Nonetheless, these improvements resulted in only small increases in the first matrix cracking stress, primary elastic modulus, and ultimate tensile strength values of the composites. In contrast, HIP consolidation of SiC/RBSN resulted in a fully dense material whose first matrix cracking stress and elastic modulus were approx. 15 and 50 percent higher, respectively, and ultimate tensile strength values were approx. 40 percent lower than those for unHIPed SiC/RBSN composites. The modulus behavior for all specimens can be explained by simple rule-of-mixture theory. Also, the loss in ultimate strength for the HIPed composites appears to be related to a degradation in fiber strength at the HIP temperature. However, the density effect on matrix fracture strength was much less than would be expected based on typical monolithic Si3N4 behavior, suggesting that composite theory is indeed operating. Possible practical implications of these observations are discussed.

Bhatt, Ramakrishna T.↗
NASA NTRS1990

Matrix density effects on the mechanical properties of SiC fiber-reinforced silicon nitride matrix properties

The room temperature mechanical properties were measured for SiC fiber reinforced reaction-bonded silicon nitride composites (SiC/RBSN) of different densities. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers (Textron SCS-6) in a reaction-bonded Si3N4 matrix. The composite density was varied by changing the consolidation pressure during RBSN processing and by hot isostatically pressing the SiC/RBSN composites. Results indicate that as the consolidation pressure was increased from 27 to 138 MPa, the average pore size of the nitrided composites decreased from 0.04 to 0.02 microns and the composite density increased from 2.07 to 2.45 gm/cc. Nonetheless, these improvements resulted in only small increases in the first matrix cracking stress, primary elastic modulus, and ultimate tensile strength values of the composites. In contrast, HIP consolidation of SiC/RBSN resulted in a fully dense material whose first matrix cracking stress and elastic modulus were approx. 15 and 50 percent higher, respectively, and ultimate tensile strength values were approx. 40 percent lower than those for unHIPed SiC/RBSN composites. The modulus behavior for all specimens can be explained by simple rule-of-mixture theory. Also, the loss in ultimate strength for the HIPed composites appears to be related to a degradation in fiber strength at the HIP temperature. However, the density effect on matrix fracture strength was much less than would be expected based on typical monolithic Si3N4 behavior, suggesting that composite theory is indeed operating. Possible practical implications of these observations are discussed.

Bhatt, Ramakrishna T.↗
DOE OSTI2026

Elastic strain engineering of lattice thermal conductivity of silicon: An ab-initio study

Silicon (Si) is the most essential material in the semiconductor industry. It is important to manage the thermal properties of crystalline Si. Elastic strain engineering (ESE) has proven to be an effective tool in controlling the electrical conductivity of Si in strained-silicon technology; its effects on the thermal conductivity of silicon, therefore, warrants careful investigation. The ESE effect is much more pronounced for nanostructured materials due to the ultralarge elastic strains (on the order of 10%) achievable at the nanoscale. In this work, the lattice thermal conductivity (κ L ) of Si under hydrostatic, biaxial, and uniaxial strain states is studied with ab-initio simulations, and the values of strain-dependent κ L compare well with experimental results and existing molecular dynamics simulations. To understand the mechanisms of strain-modulated κ L , the phonon bands, scattering rate, and Grüneisen parameters of phonon modes are computed. It is shown that strain can significantly change the anharmonicity of the crystal system, thus changing phonon scattering rates and κ L . Our results demonstrate that ESE can reduce silicon κ L by up to approximately 90%. Furthermore, uniaxial and biaxial strains can induce highly anisotropic thermal conductivity in Si, with relative variations up to 58.5% and 14.5%, respectively.

Anisotropy in Thermal Conductivity↗
NASA NTRS1996

A viscoelastic higher-order beam finite element

A viscoelastic internal variable constitutive theory is applied to a higher-order elastic beam theory and finite element formulation. The behavior of the viscous material in the beam is approximately modeled as a Maxwell solid. The finite element formulation requires additional sets of nodal variables for each relaxation time constant needed by the Maxwell solid. Recent developments in modeling viscoelastic material behavior with strain variables that are conjugate to the elastic strain measures are combined with advances in modeling through-the-thickness stresses and strains in thick beams. The result is a viscous thick-beam finite element that possesses superior characteristics for transient analysis since its nodal viscous forces are not linearly dependent an the nodal velocities, which is the case when damping matrices are used. Instead, the nodal viscous forces are directly dependent on the material's relaxation spectrum and the history of the nodal variables through a differential form of the constitutive law for a Maxwell solid. The thick beam quasistatic analysis is explored herein as a first step towards developing more complex viscoelastic models for thick plates and shells, and for dynamic analyses. The internal variable constitutive theory is derived directly from the Boltzmann superposition theorem. The mechanical strains and the conjugate internal strains are shown to be related through a system of first-order, ordinary differential equations. The total time-dependent stress is the superposition of its elastic and viscous components. Equations of motion for the solid are derived from the virtual work principle using the total time-dependent stress. Numerical examples for the problems of relaxation, creep, and cyclic creep are carried out for a beam made from an orthotropic Maxwell solid.

Johnson, Arthur R.↗
DOE OSTI2021

Challenges and transformative opportunities in superconductor vortex physics

In superconductors, the motion of vortices introduces unwanted dissipation that is disruptive to applications. Fortunately, material defects can immobilize vortices, acting as vortex pinning centers, which engenders dramatic improvements in superconductor material properties and device operation. This has motivated decades of research into developing methods of tailoring the disorder landscape in superconductors to increase the strength of vortex pinning. Yet, efficacious materials engineering still eludes us. The electromagnetic properties of real (disordered) superconducting materials cannot yet be reliably predicted, such that designing superconductors for applications remains a largely inefficient process of trial and error. This is ultimately due to large gaps in our knowledge of vortex dynamics: the field is challenged by the extremely complex interplay between vortex elasticity, vortex-vortex interactions, and material disorder. Here, we review obstacles and recent successes in understanding and controlling vortex dynamics in superconducting materials and devices. We further identify major open questions and discuss opportunities for transformative research in the field. This includes improving our understanding of vortex creep, determining and reaching the ceiling for the critical current, advanced microscopy to garner accurate structure-property relationships, frontiers in predictive simulations and the benefits of artificial intelligence, as well as controlling and exploiting vortices in quantum information applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRSDate not supplied

Computing the effective elasticity of anisotropic porous media from X-ray computed micro-tomography images

Development and optimization of composite materials designed for thermal protection of NASA’s spacecraft requires the understanding of their physical response to high-enthalpy environments. To predict their macro-scale properties and behavior, high-fidelity 3D simulations are performed at the micro-scale on realistic representations of these composites. The digital micro-structures are generated either synthetically or through X-ray micro-tomography reconstructions. One of the main challenges in the prediction of heatshield material structural response is the computation of the effective elasticity of the fibrous composite, as well as the understanding of the deformation and stresses generated at the micro-scale. These are driven by the fiber layout within the micro-structure and the distribution of the infused matrix. In this effort, the micro-mechanical linear elastic behavior of fibrous ablators is modeled through the use of a numerical method based on the Multi-Point Stress Approximation (MPSA) finite volume scheme. The MPSA, a generalization of the more commonly used Multi-Point Flux Approximation (MPFA), was discussed in a previous presentation at the 15th USCCN and in reference. To predict the behavior of fibrous and woven architectures, algorithms that compute the local fiber orientation are used. The implementation of the MPSA was verified using analytical solutions, engineering test cases and compared against legacy Finite Element Analysis (FEA) software. The stress analysis models were then applied to real geometries used by NASA in thermal protection systems such as fibrous preforms and woven materials and the results were compared to experimental data.

Federico Semeraro↗
NASA NTRS2001

Solid Freeform Fabrication of Continuous Fiber Reinforced Composites for Propulsion Applications

Monolithic ceramics lack the fracture toughness necessary to be considered for propulsion related applications. To be used for such applications, materials must possess low density, high elastic modulus, a low thermal expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. They will in many cases also be required to possess the ability to be joined, to survive thermal cycling and multi-axial stress states, and for reusable applications the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attributes for these materials are the need to be of low cost and readily available in large quantities.

Vaidyanathan, R.↗