Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Exploratory Investigation at Mach Number of 2.01 of the Longitudinal Stability and Control Characteristics of a Winged Reentry Configuration

An investigation has been conducted to determine the longitudinal stability and control characteristics of a reentry configuration at a Mach number of 2.01. The configuration consisted of clipped delta wing with hinged wing-tip panels. The results indicate that deflecting the wing-tip panels from a position normal to the wing chord plane to a position coincident with the wing chord plane resulted in a stabilizing change in the pitching-moment characteristics but did not significantly affect the nonlinearity of the pitching-moment variation with angle of attack. The trailing-edge controls were effective in producing pitching moment throughout the angle-of-attack range for control deflections up to at least 600. The control deflection required for trim, however, varied nonlinearly with angle of attack. It would appear that this nonlinearity as well as the maximum deflection required for trim could be greatly decreased by utilizing a leading-edge control in conjunction with a trailing-edge control.

Foster, Gerald V.↗
NASA NTRS2018

Geometry and Joint Systems for Lattice-Based Reconfigurable Space Structures

We describe analytical methods for the design of the discrete elements of ultralight lattice structures. This modular, building block strategy allows for relatively simple element manufacturing, as well as relatively simple robotic assembly of low mass density structures on orbit, with potential for disassembly and reassembly into highly varying and large structures. This method also results in a structure that is easily navigable by relatively small mobile robots. The geometry of the cell can allow for high packing efficiency to minimize wasted payload volume while maximizing structural performance and constructability. We describe the effect of geometry choices on the final system mechanical properties, manufacturability of the components, and automated robotic constructability of a final system. Geometry choices considered include building block complexity, symmetry of the unit cell, and effects of vertex, edge, and face connectivity of the unit cell. Mechanical properties considered include strength scaling, modulus scaling, and structural performance of the joint, including proof load, shear load, mass, and loading area; as well as validation and verification opportunities. Manufacturability metrics include cost and time, manufacturing method (COTS versus custom), and tolerances required. Automated constructability metrics include local effects of loads imparted to the structure by the robot and assembly complexity, encompassing the ability of the robot to clamp and number of placement motions needed for assembly.

Ochalek, Megan E.↗
DOE OSTI2024

Engineering a non-Hermitian second-order topological insulator state in quasicrystals

Non-Hermitian topological phases have gained immense attention due to their potential to unlock novel features beyond Hermitian bounds. PT -symmetric (parity time-reversal symmetric) non-Hermitian models have been studied extensively over the past decade. In recent years, the topological properties of general non-Hermitian models, regardless of the balance between gains and losses, have also attracted vast attention. Here, we propose a non-Hermitian second-order topological (SOT) insulator that hosts gapless corner states on a two-dimensional quasicrystalline lattice (QL). We first construct a non-Hermitian extension of the Bernevig-Hughes-Zhang model on a QL generated by the Amman-Beenker tiling. This model has real spectra and supports helical edge states. Corner states emerge by adding a proper Wilson-mass term that gaps out the edge states. We propose two variations of the mass term that result in fascinating characteristics. In the first variation, we obtain a purely real spectra for the second-order topological phase. In the latter, we get a complex spectra with corner states localized at only two corners due to the higher-order non-Hermitian skin effect of the edge modes. Furthermore, our findings pave a path to engineering exotic SOT phases where corner states can be localized at designated corners.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1992

Effect of low-speed impact damage and damage location on behavior of composite panels

An investigation of the effects of low-speed impact damage on the compression and tension strength of thin (less than .05 inches thick) and moderately thick (between .12 and .17 inches thick) composite specimens was conducted. Impact speeds ranged from 50 to 550 ft/sec (impact energies from .25 to 30.7 ft-lb) and impact locations were near or away from a lateral unloaded edge. In this study, thin tension-loaded or compression-loaded specimens with only 90 deg and +/- 40 deg plies which were impacted away from the unloaded edge suffered less reduction in maximum load-carrying capability due to impact damage than the same specimens impacted near the unloaded edge. Unlike the thin laminates, failure loads of thicker compression-loaded specimens with a similar stacking sequence were independent of impact location. Failure loads of thin tension-loaded specimens with 0 deg plies were independent of impact location while failure loads of thicker compression-loaded specimens with 0 deg plies were dependent upon impact location. A finite-element analysis of strain distributions across the panel width indicated that high axial strains occur near the unloaded edges of postbuckled panels, indicating that impacts near the unloaded edge would significantly effect the behavior of postbuckled panels.

Jegley, Dawn↗
NASA NTRS2000

Towards Development of Microcalorimeter Arrays of Mo/Au Transition-Edge Sensors with Bismuth Absorbers

We report on our progress towards the development of arrays of X-ray microcalorimeters as candidates for the high resolution x-ray spectrometer on the Constellation-X mission. The microcalorimeter arrays (30 x 30) with appropriate pixel sizes (0.25 mm. x 0.25 mm) and high packing fractions (greater than 96%) are being developed. Each individual pixel has a 10 micron thick Bi X-ray absorber that is shaped like a mushroom to increase the packing fraction, and a Mo/Au proximity effect superconducting transition edge sensor (TES). These are deposited on a 0.25 or 0.5 micron thick silicon nitride membrane with slits to provide a controllable weak thermal link to the sink temperature. Studies are underway to model, test and optimize the TES pixel uniformity, critical current, heat capacity and the membrane thermal conductance in the array structure. Fabrication issues and procedures, and results of our efforts based on these optimizations will be provided.

Tralshawala, Nilesh↗
DOE OSTI2022

Near‐Cloud Aerosol Retrieval Using Machine Learning Techniques, and Implied Direct Radiative Effects

Abstract There is a lack of satellite‐based aerosol retrievals in the vicinity of low‐topped clouds, mainly because reflectance from aerosols is overwhelmed by three‐dimensional cloud radiative effects. To account for cloud radiative effects on reflectance observations, we develop a Convolutional Neural Network and retrieve aerosol optical depth (AOD) with 100–500 m horizontal resolution for all cloud‐free regions regardless of their distances to clouds. The retrieval uncertainty is 0.01 + 5%AOD, and the mean bias is approximately −2%. In an application to satellite observations, aerosol hygroscopic growth due to humidification near clouds enhances AOD by 100% in regions within 1 km of cloud edges. The humidification effect leads to an overall 55% increase in the clear‐sky aerosol direct radiative effect. Although this increase is based on a case study, it highlights the importance of aerosol retrievals in near‐cloud regions, and the need to incorporate the humidification effect in radiative forcing estimates.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1961

STOL Characteristics of a Propeller-Driven, Aspect-Ratio-10, Straight-Wing Airplane with Boundary-Layer Control Flaps, as Estimated from Large-Scale Wind-Tunnel Tests

A study is presented of the improvements in take-off and landing distances possible with a conventional propeller-driven transport-type airplane when the available lift is increased by propeller slipstream effects and by very effective trailing-edge flaps and ailerons. This study is based on wind-tunnel tests of a 45-foot span, powered model, with BLC on the trailing-edge flaps and controls. The data were applied to an assumed airplane with four propellers and a wing loading of 50 pounds per square foot. Also included is an examination of the stability and control problems that may result in the landing and take-off speed range of such a vehicle. The results indicated that the landing and take-off distances could be more than halved by the use of highly effective flaps in combination with large amounts of engine power to augment lift (STOL). At the lowest speeds considered (about 50 knots), adequate longitudinal stability was obtained but the lateral and directional stability were unsatisfactory. At these low speeds, the conventional aerodynamic control surfaces may not be able to cope with the forces and moments produced by symmetric, as well as asymmetric, engine operation. This problem was alleviated by BLC applied to the control surfaces.

Weiberg, James A↗
NASA NTRS2000

Stator Loading Measurements Behind a Fan With Trailing Edge Blowing

The problem of aircraft noise pollution around airports has become increasingly important as those areas have become more densely populated. Currently, the removal of older noisier aircraft from operation is reducing noise levels around airports; however, with air traffic projected to increase by about 5% over the next decade the number of commercial aircraft operating in the world is expected to be about 17,700 by the year 2007. To keep noise levels around airports from increasing as a result of traffic increases, it is important to investigate new methods of noise reduction. The objective of this work is to provide a better understanding of the effects that trailing edge blowing has on stator unsteady loading. This is done by presenting flowfield and stator loading data from experiments conducted with and without trailing edge blowing.

Waitz, Ian A.↗
NASA NTRS2021

EXEP: Catching the rays- modeling the stray light background of a starshade.

Diffraction and reflection from the optical edges is the dominant source of stray light from a starshade. However, recent progress in optical edge design has led to much reduced predictions of stray light deriving from this source. Secondary sources now also play a role; these sources arise from two or more reflections from the starshade structure. These multiple reflections allow light to reach the telescope from parts of the structure that are shaded from direct sunlight. Here we analyze the secondary sources for the starshade model developed as part of the NASA’s S5 starshade technology development and show the effects of optical edge mechanical design variants and mitigations.

Stegman, Matthew↗
NASA NTRS1984

The influence of leading-edge load alleviation on supersonic wing design

A theoretical and experimental program to assess the effect of leading-edge load constraints on wing design and performance was conducted. For a planform characterized by a highly swept leading edge on the inboard region, linear theory was used to design camber surfaces which produced minimum drag-due-to-lift at the design lift coefficient of 0.08 and a design Mach number of 2.4. In an effort to delay the formation of leading edge vortices which often occur on highly swept wings, two approaches were used in the design criteria to limit the loadings on the leading edge. One wing was constrained to have the normal Mach number less than one everywhere along the leading edge and the second wing was constrained to have a pressure coefficient of zero on the leading edge. Force tests were run on the two constrained wings, on a flat reference wing and on an optimized wing with no leading edge constraints. All wings had identical planforms and thicknesses and were tested over a range of Mach numbers from 1.8 to 2.8 and a range in angles of attack from -5 deg to 8 deg. A comparison of the experimental performance of these four models is shown. Correlations of these results with theoretical predictions and flow visualization photographs are also included.

Darden, C. M.↗
NASA NTRS1996

Probabilistic Simulation of Progressive Fracture in Bolted-Joint Composite Laminates

This report describes computational methods to probabilistically simulate fracture in bolted composite structures. An innovative approach that is independent of stress intensity factors and fracture toughness was used to simulate progressive fracture. The effect of design variable uncertainties on structural damage was also quantified. A fast probability integrator assessed the scatter in the composite structure response before and after damage. Then the sensitivity of the response to design variables was computed. General-purpose methods, which are applicable to bolted joints in all types of structures and in all fracture processes-from damage initiation to unstable propagation and global structure collapse-were used. These methods were demonstrated for a bolted joint of a polymer matrix composite panel under edge loads. The effects of the fabrication process were included in the simulation of damage in the bolted panel. Results showed that the most effective way to reduce end displacement at fracture is to control both the load and the ply thickness. The cumulative probability for longitudinal stress in all plies was most sensitive to the load; in the 0 deg. plies it was very sensitive to ply thickness. The cumulative probability for transverse stress was most sensitive to the matrix coefficient of thermal expansion. In addition, fiber volume ratio and fiber transverse modulus both contributed significantly to the cumulative probability for the transverse stresses in all the plies.

Minnetyan, L.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet-pressure data were obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top-mounted twin inlets. Data are presented from wind tunnel tests conducted at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27-deg and angles of sideslip up to 12-deg. Trimmed aerodynamic characteristics and inlet performance were compared for three different leading-edge extension (LEX) configurations. The effects of wing leading- and trailing-edge flaps on the inlet were also determined. Maneuver performance was calculated from combined force and inlet-pressure data. The largest of the three LEX sizes tested gave the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗
NASA NTRS1982

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet pressure data are obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top mounted twin inlets. Data are presented from tests conducted in the Ames Unitary Wind Tunnels at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27 deg. and angles of sideslip up to 12 deg. Trimmed aerodynamic characteristics and inlet performance are compared for three different leading edge extension (LEX) configurations. The effects of wing leading and trailing-edge flaps on the inlet are also determined. Maneuver perfromance is calculated form combined force and inlet pressure data. The largest of the three LEX sizes tested gives the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗
NASA NTRS1985

An experimental investigation of apex fence flaps on delta wings

The effects on leading edge vortex formation produced by apex fences mounted on two delta wings were examined in a subsonic wind tunnel. Pressure data were collected on the upper surface of the test wings and oil flow and bubble flow visualizations were performed. The deflections studied were 74, 90 and 65 deg in one-sided and two-sided configurations. Full span and semi-span delta wing planforms were used. Relatively small, symmetrically deployed apex fences provided enhanced upper surface suction which, in some angle-of-attack situations, could lead to a pitch-up force. Asymmetrically-deployed fences showed promise for yaw control at high angles of attack, althouh the force effectiveness has yet to be quantified.

Vess, R. J.↗
NASA NTRS1990

Connection between leading-edge sweep, vortex lift, and vortex strength for delta wings

An effort is made to clarify the effect of leading-edge sweep on the vortex lift and leading-edge vortex strength of a slender wing; while it is often assumed that increasing sweep enhances vortex lift and strength, the opposite is the case. The suction analogy is used in association with numerical and experimental data to derive simple formulas yielding the actual relationship for delta wings. The difference between vortex lift and nonlinear lift is highlighted.

Hemsch, Michael J.↗