Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design augmentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Feasibility of water injection into the turbine coolant to permit gas turbine contingency power for helicopter application

A system which would allow a substantially increased output from a turboshaft engine for brief periods in emergency situations with little or no loss of turbine stress rupture life is proposed and studied analytically. The increased engine output is obtained by overtemperaturing the turbine; however, the temperature of the compressor bleed air used for hot section cooling is lowered by injecting and evaporating water. This decrease in cooling air temperature can offset the effect of increased gas temperature and increased shaft speed and thus keep turbine blade stress rupture life constant. The analysis utilized the NASA-Navy-Engine-Program or NNEP computer code to model the turboshaft engine in both design and off-design modes. This report is concerned with the effect of the proposed method of power augmentation on the engine cycle and turbine components. A simple cycle turboshaft engine with a 16:1 pressure ratio and a 1533 K (2760 R) turbine inlet temperature operating at sea level static conditions was studied to determine the possible power increase and the effect on turbine stress rupture life that could be expected using the proposed emergency cooling scheme. The analysis showed a 54 percent increse in output power can be achieved with no loss in gas generator turbine stress rupture life. A 231 K (415 F) rise in turbine inlet temperature is required for this level of augmentation. The required water flow rate was found to be .0109 kg water per kg of engine air flow.

Vanfossen, G. J.↗
NASA NTRS1982

Space Shuttle Orbiter onboard rendezvous navigation

Much of the work that the Space Shuttle will perform requires a capability to rendezvous with other orbiting objects. The formulation and design philosophy behind the Space Shuttle Orbiter rendezvous navigation system are the subjects of this paper. The current rendezvous navigation design incorporates a Kalman filter to estimate the relative position and velocity. The filter is augmented with state elements for the estimation of colored measurement noise and acceleration modeling errors. Several measurement types are available to the filter: a manual optical sighting device, an automatic optical tracking instrument, and a rendezvous radar which provides range and range rate measurements as well as the line of sight direction. The filter also includes a technique for detecting highly improbable measurements and excluding them from Kalman processing.

Little, M. J.↗
NASA NTRS1993

Status report of RMS active damping augmentation

A status report of Remote Manipulator System (RMS) active damping augmentation is presented. Topics covered include: active damping augmentation; benefits of RMS ADA; simulated payload definition; sensor and actuator definition; ADA control law design; Shuttle Engineering Simulator (SES) real-time simulation; and astronaut evaluation.

Gilbert, Mike↗
NASA NTRS1997

Development of an Apparatus for Wind Tunnel Dynamic Experiments at High-alpha

A unique experimental apparatus that allows a wind tunnel model two degrees of freedom has been designed and built. The apparatus was developed to investigate the use of new methods to augment aircraft control in the high angle of attack regime. The model support system provides a platform in which the roll-yaw coupling at high angles of attack can be studied in a controlled environment. Active cancellation of external effects is used to provide a system in which the dynamics are dominated by the aerodynamic loads acting on the wind tunnel model.

Pedreiro, Nelson↗
NASA NTRS1997

Development of an Apparatus for Wind Tunnel Dynamic Experiments at High-alpha

A unique experimental apparatus that allows a wind tunnel model two degrees of freedom has been designed and built. The apparatus was developed to investigate the use of new methods to augment aircraft control in the high angle of attack regime. The model support system provides a platform in which the roll-yaw coupling at high angles of attack can be studied in a controlled environment. Active cancellation of external effects is used to provide a system in which the dynamics are dominated by the aerodynamic loads acting on the wind tunnel model.

Pedreiro, Nelson↗
NASA NTRS2001

Empirical Requirements Analysis for Mars Surface Operations Using the Flashline Mars Arctic Research Station

Living and working on Mars will require model-based computer systems for maintaining and controlling complex life support, communication, transportation, and power systems. This technology must work properly on the first three-year mission, augmenting human autonomy, without adding-yet more complexity to be diagnosed and repaired. One design method is to work with scientists in analog (mars-like) setting to understand how they prefer to work, what constrains will be imposed by the Mars environment, and how to ameliorate difficulties. We describe how we are using empirical requirements analysis to prototype model-based tools at a research station in the High Canadian Arctic.

Clancey, William J.↗
DOE OSTI2022

Progress Towards a Predictive Eagle Behavior and Risk Modeling Framework: Overview and Recent Validation Efforts

This presentation summarizes progress to date of the U.S. Department of Energy project, "Development of a computational framework for modeling golden eagles (Aquila chrysaetos) near wind farms," which focuses on stochastic behavioral modeling of soaring raptors across landscape, facility, and turbine spatiotemporal scales. This publicly available, open-source modeling framework includes behavioral models based on three different underlying principles: energy minimization at landscape scale, behavioral heuristics at landscape-facility scale, and data-driven behaviors at the facility-micro-scale. We will briefly overview the key advancements in the behavioral modeling state of the art, which leverages multiple high-resolution telemetry data sources combined with high-fidelity atmospheric flow modeling insights. We then present preliminary results from a validation study in Altamont, California. This new study involves a novel application of the Stochastic Soaring Raptor Simulator (SSRS), in a new geographic locale, to understand facility scale eagle movement patterns over time scales representative of a wind project's lifetime. For this desktop analysis (that does not depend on any high-performance computing resources), SSRS simultaneously considers a variety of wind conditions and eagle approach vectors toward a project site of interest. This work demonstrates the integration of publicly available landscape-scale atmospheric datasets, our recently improved engineering updraft models (see presentation from Thedin et al.), and our energy minimization behavioral models within the SSRS framework. While we only present results from a single behavioral model, the integration of these three modeling components forms the foundation for our more sophisticated behavioral models (see presentations from Brandes et al., Sandhu et al.) that are under active development. Results are presented in the form of presence maps, which may be applied to estimate risk to wildlife, augment ground survey data, inform wind-plant operations, or incorporated into wind-plant designs.

agent-based modeling↗
DOE OSTI2026

Performance enhancement of direct-drive shock-augmented ignition inertial fusion implosions through shock timing optimization

Shock-augmented ignition (SAI) [R. H. H. Scott et al., Phys. Rev. Lett. 129, 195001 (2022)] is an alternative inertial confinement fusion concept that is designed to achieve high energy gain by combining improved resilience to instabilities with enhanced fuel compression. In SAI, lower implosion velocities can improve hydrodynamic stability and limited laser intensities reduce the excitation of detrimental laser-plasma instabilities, enabling greater areal density accumulation. Here we report an experimental investigation of SAI using a series of warm D 2 implosions. By timing the augmenting shock to arrive at the implosion center immediately prior to peak compression, the areal density and hot-spot pressure increase by 50% and 112%, respectively, relative to unoptimized designs. Ignition-scale simulations reproduce the observed timing dependence and demonstrate the potential of SAI for inertial fusion energy.

Direct drive↗
NASA NTRS2013

Sabots, Obturator and Gas-In-Launch Tube Techniques for Heat Flux Models in Ballistic Ranges

For thermal protection system (heat shield) design for space vehicle entry into earth and other planetary atmospheres, it is essential to know the augmentation of the heat flux due to vehicle surface roughness. At the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (HFFAF) ballistic range, a campaign of heat flux studies on rough models, using infrared camera techniques, has been initiated. Several phenomena can interfere with obtaining good heat flux data when using this measuring technique. These include leakage of the hot drive gas in the gun barrel through joints in the sabot (model carrier) to create spurious thermal imprints on the model forebody, deposition of sabot material on the model forebody, thereby changing the thermal properties of the model surface and unknown in-barrel heating of the model. This report presents developments in launch techniques to greatly reduce or eliminate these problems. The techniques include the use of obturator cups behind the launch package, enclosed versus open front sabot designs and the use of hydrogen gas in the launch tube. Attention also had to be paid to the problem of the obturator drafting behind the model and impacting the model. Of the techniques presented, the obturator cups and hydrogen in the launch tube were successful when properly implemented

obturators↗
NASA NTRS1974

Variable geometry for supersonic mixed-compression inlets

Study of two-dimensional and axisymmetric supersonic mixed-compression inlet systems has shown that the geometry of both systems can be varied to provide adequate transonic airflow to satisfy the airflow demand of most jet engines. Collapsing geometry systems for both types of inlet systems provide a generous amount of transonic airflow for any design Mach number inlet system. However, the mechanical practicality of collapsing centerbodies for axisymmetric inlet systems is doubtful. Therefore, translating centerbody axisymmetric inlets with auxiliary airflow systems to augment the transonic airflow capability are an attractive alternative. Estimates show that the capture mass-flow ratio at Mach number 1.0 can be increased approximately 0.20 for a very short axisymmetric inlet system designed for Mach number 2.37. With this increase in mass-flow ratio, even variable-cycle engine transonic airflow demand can be matched without oversizing the inlet at the design Mach number.

Sorensen, N. E.↗
NASA NTRSDate not supplied

An Evaluation of Extended Reality Technologies for Use in Verification Testing at NASA 2024 HRP IWS Abstract

BACKGROUND At NASA, verification testing is the formal process of ensuring that a product conforms to requirements set by a project or program. Some verification methods, such as Demonstrations and Test, require either the end product or a mockup of the product with sufficient fidelity to stand-in for the product during the test. Traditionally, these mockups have been physical (e.g., foam-core and wood) but there is growing interest in exploring new methods for testing with these mockups. These methods include virtual reality (VR), mixed reality, and augmented reality which are collectively referred to as eXtended Reality (XR) technologies. VR has already been adopted and used by many in the aerospace industry as a tool for use in early design phases (e.g., developmental testing) and may have the most potential for use in verification tests. Benefits of using VR mockups offer cost effectiveness, ease of iteration, simulation of hazardous conditions (e.g., an egress through a hatch with smoke obscuring vision), and the ability to simulate microgravity conditions, which are challenging to do with physical mockups. However, the validity of test results obtained from VR mockup demonstrations or testing, compared to the current gold standard of physical mockups, remains uncertain. It is unlikely that there is one clean answer as there are many different types of verification outcomes and each XR technology must be evaluated on its own merits. This is not an issue during developmental testing as the design is still in flux and the total success of the design is not dependent upon the results of a developmental test. Verification tests, however, only happen once, assuming no change to the design, and the results are used to certify the product. Therefore, establishing the validity of XR mockup-based verification outcomes is essential before considering them for any use in verification tests. OBJECTIVE AND METHOD To address this concern, the Human Research Program has funded a project to explore and qualify how XR technologies might be used in verification demonstration and testing at NASA. Currently, we are conducting a review of the literature on the utilization of XR mockups for design activities, prototyping, and user testing. We are employing the Strengths, Weaknesses, Opportunities, and Threats (SWOT) analysis method to identify the pros, cons, and barriers to adoption of XR technologies for verification testing at NASA. Additionally, we are developing a framework to guide the deployment of XR mockups for verification tests. Building upon available evidence from the literature and subject-matter expert feedback, our goal for the framework is to provide guidelines for which forms of XR mockups are suitable for a given verification test, when only physical mockups should be employed and to highlight areas for which more evidence is needed. To further refine our framework and to contribute to the body of evidence, we are planning a lab-based experiment comparing a VR mockup to a physical twin for a set of select verification outcomes. ANTICIPATED RESULTS In this presentation, we will present the work we conducted to evaluate XR technologies for use in verification tests at NASA. We will summarize and report our findings from the SWOT analysis and our lab-based study, and we will present the current state of the XR Technologies for Verification Testing framework. We will conclude by summarizing remaining work and future directions for the project. Technologies for Verification Testing framework. We will conclude by summarizing remaining work and future directions for the project.

Extended Reality↗
NASA NTRS1992

Truss topology optimization with simultaneous analysis and design

Strategies for topology optimization of trusses for minimum weight subject to stress and displacement constraints by Simultaneous Analysis and Design (SAND) are considered. The ground structure approach is used. A penalty function formulation of SAND is compared with an augmented Lagrangian formulation. The efficiency of SAND in handling combinations of general constraints is tested. A strategy for obtaining an optimal topology by minimizing the compliance of the truss is compared with a direct weight minimization solution to satisfy stress and displacement constraints. It is shown that for some problems, starting from the ground structure and using SAND is better than starting from a minimum compliance topology design and optimizing only the cross sections for minimum weight under stress and displacement constraints. A member elimination strategy to save CPU time is discussed.

Sankaranarayanan, S.↗
NASA NTRS2016

Large-Scale V/STOL Experimental Investigations of an Ejector-Lift Fighter and a Twin Tilt-Nacelle Transport

In the 1980s NASA Aeronautics was actively involved in full-scale wind tunnel testing of promising VSTOL aircraft concepts. This presentation looks at two, a multi-role fighter and a subsonic tactical transport. Their strengths and weaknesses are discussed with some of the rationale that ultimately led to the selection of competing concepts for production, namely the V-22 Osprey and the F-35 Lightning. The E7-A STOVL multi-role fighter was the product of an aircraft development program in the late 1980s by NASA, the Defense Advanced Research Projects Agency (DARPA), the Canadian Department of Industry Science and Technology (DIST), and industry partners General Dynamics and Boeing Dehavilland. The program was conducted an in response to increasing US-UK interest in supersonic STOVL fighters. The objective was to design an aircraft that could replace most existing close air support-air combat fighters with a single aircraft that had some of the qualities of an air superiority fighter and the deployment flexibility of a VSTOL aircraft. The resulting E7-A concept was a delta-wing supersonic fighter that used a fuselage-mounted thrust augmenting ejector and a ventral deflecting jet nozzle for vertical lift. The Grumman Aircraft Company, the Navy, and NASA developed the Design-698 (D-698) subsonic tactical transport in response to the Navy's Type A VSTOL utility aircraft requirement. The objective was to develop a subsonic utility transport with the operational flexibility of a helicopter, but with greater speed and range. The D-698 employs two high-bypass turbofan engines mounted on a dumbbell that rotates through ninety degrees for vertical takeoff and cruise flight. Movable vanes positioned in the exhaust flow provide control in hover with the need for reaction control jets. The presentations concluding comments suggest that technology advances in the last thirty-years may justify the value of revisiting some of these concepts.

Powered Lift↗
NASA NTRS1992

Spacecraft flight control system design selection process for a geostationary communication satellite

The Earth's first artificial satellite, Sputnik 1, slowly tumbled in orbit. The first U.S. satellite, Explorer 1, also tumbled out of control. Now, as we launch the Mars observer and the Cassini spacecraft, stability and control have become higher priorities. The flight control system design selection process is reviewed using as an example a geostationary communication satellite which is to have a life expectancy of 10 to 14 years. Disturbance torques including aerodynamic, magnetic, gravity gradient, solar, micrometeorite, debris, collision, and internal torques are assessed to quantify the disturbance environment so that the required compensating torque can be determined. Then control torque options, including passive versus active, momentum control, bias momentum, spin stabilization, dual spin, gravity gradient, magnetic, reaction wheels, control moment gyros, nutation dampers, inertia augmentation techniques, three-axis control, reactions control system (RCS), and RCS sizing, are considered. A flight control system design is then selected and preliminary stability criteria are met by the control gains selection.

Barret, C.↗
NASA NTRS1999

Development of a 12-Thrust Chamber Kerosene /Oxygen Primary Rocket Sub-System for an Early (1964) Air-Augmented Rocket Ground-Test System

Airbreathing/Rocket combined-cycle, and specifically rocket-based combined- cycle (RBCC), propulsion systems, typically employ an internal engine flow-path installed primary rocket subsystem. To achieve acceptably short mixing lengths in effecting the "air augmentation" process, a large rocket-exhaust/air interfacial mixing surface is needed. This leads, in some engine design concepts, to a "cluster" of small rocket units, suitably arrayed in the flowpath. To support an early (1964) subscale ground-test of a specific RBCC concept, such a 12-rocket cluster was developed by NASA's Marshall Space Flight Center (MSFC). The small primary rockets used in the cluster assembly were modified versions of an existing small kerosene/oxygen water-cooled rocket engine unit routinely tested at MSFC. Following individual thrust-chamber tests and overall subsystem qualification testing, the cluster assembly was installed at the U. S. Air Force's Arnold Engineering Development Center (AEDC) for RBCC systems testing. (The results of the special air-augmented rocket testing are not covered here.) While this project was eventually successfully completed, a number of hardware integration problems were met, leading to catastrophic thrust chamber failures. The principal "lessons learned" in conducting this early primary rocket subsystem experimental effort are documented here as a basic knowledge-base contribution for the benefit of today's RBCC research and development community.

Pryor, D.↗
NASA NTRS1980

Landing flying qualities evaluation criteria for augmented aircraft

The criteria evaluated were: Calspan Neal-Smith; Onstott (Northrop Time Domain); McDonnell-Douglas Equivalent System Approach; R. H. Smith Criterion. Each criterion was applied to the same set of longitudinal approach and landing flying qualities data. A revised version of the Neal-Smith criterion which is applicable to the landing task was developed and tested against other landing flying qualities data. Results indicated that both the revised Neal-Smith criterion and the Equivalent System Approach are good discriminators of pitch landing flying qualities; Neal-Smith has particular merit as a design guide, while the Equivalent System Approach is well suited for development of appropriate military specification requirements applicable to highly augmented aircraft.

Radford, R. C.↗
NASA NTRS2000

Metrology Mount and Optics Mandrels

This document is the Final Report for NASA Grant NAG8-1198 from NASA Marshall Space Flight Center (MSFC) to the Smithsonian Astrophysical Observatory (SAO). The Grant is entitled "Metrology Mount and Optics Materials." This final report is required by the terms of the Grant. The period of performance was from September 15, 1995 through January 14, 1999. Total funding received by SAO from MSFC for this effort was, $254,000. Mr. Lester Cohen carried out most of the work at SAO, but received limited support from other engineers, technicians, and designers. Dr. Harvey Tananbaum, the Principal Investigator for the grant provided overall direction and work- assessment. The Grant has had two funding augmentations to its basic amount and has, over time, emphasized three different research areas - each of which has been an extension of earlier research. The research activity was in 2 areas: (1) Expert opto-structural studies related to separation mechanics and effects of electro formed nickel X-ray mirrors. and (2) Design, fabrication and evaluation of a low force metrology and assembly station for light weight full shell electroformed X-ray mirrors.

Tananbaum, H.↗
NASA NTRS1981

A flight investigation of static stability, control augmentation, and flight director influences on helicopter IFR handling qualities

A flight experiment was conducted using the NASA-Army V/STOLAND UH-1H variable-stability helicopter to investigate the influence of several longitudinal-static-stability, control-augmentation, and flight-director parameters on helicopter flying qualities during terminal area operations in instrument conditions. This experiment, which was part of a joint NASA/FAA program pertaining to helicopter IFR airworthiness, was designed to corroborate and extend previous ground simulation results obtained in this program. Variations examined included stable and neutral longitudinal control position gradients, rate-damping and attitude-command augmentation, and raw data versus flight-director displays. Pilot rating results agreed excellently with the ground simulation data, indicating an adequate instrument capability with rate-damping augmentation and neutral statics and the need for pitch-roll attitude augmentation to achieve a satisfactory system.

Lebacqz, J. V.↗