Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “density lithium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Overcoming Anode Instability in Solid‐State Batteries through Control of the Lithium Metal Microstructure

Abstract Enabling the lithium metal anode (LMA) in solid‐state batteries (SSBs) is the key to developing high energy density battery technologies. However, maintaining a stable electrode–electrolyte interface presents a critical challenge to high cycling rate and prolonged cycle life. One such issue is the interfacial pore formation in LMA during stripping. To overcome this, either higher stack pressure or binary lithium alloy anodes are used. Herein, it is shown that fine‐grained ( d = 20 µm) polycrystalline LMA can avoid pore formation by exploiting the microstructural dependence of the creep rates. In a symmetric cell set‐up, i.e., LiǀLi 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO)ǀLi, fine‐grained LMA achieves > 11.0 mAh cm −2 compared to ≈ 3.6 mAh cm −2 for coarse‐grained LMA ( d = 295 µm) at 0.1 mA cm −2 and at moderate stress of 2.0 MPa. Smaller diffusion lengths (≈ 20 µm) and higher diffusivity pathway along dislocations ( D d ≈ 10 −7 cm 2 s −1 ), generated during cell fabrication, result in enhanced viscoplastic deformation in fine‐grained polycrystalline LMA. The electrochemical performances corroborate well with estimated creep rates. Thus, microstructural control of LMA can significantly reduce the required stack pressure during stripping. These results are particularly relevant for “anode‐free” SSBs wherein both the microstructure and the mechanical state of the lithium are critical parameters.

25 ENERGY STORAGE↗
DOE OSTI2025

Modeling Structured Electrodes and Graded Porosity for Improving Discharge Rate Capability in Ultra-Thick Graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 Batteries

Long-range electric vehicles (EVs) require high-energy-density batteries that also meet the power demands of high current charge and discharge. Ultra-thick (>100 μm) Lithium-ion battery electrodes are critical to enable this need, but slow ion transport in conventional uniform electrodes (UEs) reduces battery capacity at increasing charge/discharge rates. We present a 3D computational analysis on the impact of structured electrode (SE) and graded electrode (GE) geometries on the discharge rate capability of ultra-thick graphite|LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) battery cells based on the footprint of a commercial EV pouch cell. SE cathodes with either a “grid” or “line” geometry and GEs with two layers of porosity were modeled. Based on the results of 230 models, we found that the electrolyte volume fraction is a key parameter that impacts capacity improvements in UEs, GEs, and SEs at 2 C–6 C discharge rates. SEs have the greatest discharge rate capability, outperforming GEs and UEs due to reduced Lithium-ion concentration gradients across the electrode thickness, which mitigates electrolyte depletion at high rates. The best SE model has a “grid” geometry with gravimetric and volumetric energy density improvements of 0.9%–4% at C/2–2 C and 18%–24% at 4 C–6 C relative to UEs.

25 ENERGY STORAGE↗
DOE OSTI2025

Porous and Amorphous Mn x Mo 3 S 13 Chalcogel Electrode for High-Capacity Conversion-Based Lithium-Ion Batteries

While Li-ion batteries (LIBs) are a leading energy storage technology, their energy densities are limited by the low capacity of conventional intercalation cathodes, driving interest in high energy-density Li–S batteries that make use of conversion chemistry. Achieving high capacity, reversibility, and cycle stability, and controlling volume changes in conversion batteries during the charge–discharge process, however, remains challenging. Here, in this study, we present a porous, amorphous, sulfide-based Mn x Mo 3 S 13 chalcogel, which concurrently offers high capacity and cycle stability. The solution-processable room temperature synthesized Mn x Mo 3 S 13 (x = 0.25) chalcogel exhibits a local structure that resembles the Mo 3 S 13 cluster with Mn 2+ distributed across the Mo 3 S 13 matrix, as determined by synchrotron X-ray pair distribution function (PDF) and extended X-ray absorption fine structure (EXAFS). Ab initio molecular dynamics (AIMD) simulations reveal that Mn 2+ incorporation shortens the polysulfide chain in the gel matrix compared to the Mo 3 S 13 chalcogel, while forming a coordination environment with disulfide groups, analogous to the experimental findings. A Li/Mn 0.25 Mo 3 S 13 half-cell delivers 897 mAh g –1 capacity during the first discharge and retains 571 mAh g –1 capacity after 100 cycles at a C/3 rate. Distribution of relaxation time (DRT) unveils a stable solid–electrolyte interphase (SEI) formation upon cycling that enables charge–discharge reversibility. Here, the enhanced capacity retention and cycle stability compared to those of the Li/Mo 3 S 13 cell are attributed to the reduced dissolution of active mass into the electrolyte, facilitated by the formation of shorter polysulfide chains within the Mn 0.25 Mo 3 S 13 structure and the strong affinity of Lewis-acidic Mn 2+ for polysulfide anions generated during the charge–discharge process of the Li/Mn 0.25 Mo 3 S 13 cell. Thus, this work illustrates a design principle of material for high-capacity and cycle-stable Li-metal sulfide batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Experimental study on a novel three-phase absorption thermal battery with high energy density applied to buildings

Buildings contribute to 75% of total electricity consumption and 80% of peak electricity demand in the United States. A significant portion of building electricity consumption goes to space conditioning. Therefore, using thermal energy storage (TES) to decouple the building electricity consumption and the fluctuating space-conditioning load has significant potential to shift peak electricity demand and improve the stability of the grid. To provide effective TES within the spatial constraints in buildings, a three-phase absorption thermal battery (TATB) system with very high energy storage density was designed and studied. The TATB stores low-temperature heat in hydrate crystals of salts and supports space conditioning through absorption systems. In this study, a benchtop TATB using lithium chloride (LiCl) hydrate crystals as the storage material was tested under practical operating conditions for its energy storage density and discharge rate. We report the TATB successfully generated LiCl hydrate crystals during charging mode and then dissolved the crystals during discharging mode. A material-based energy storage density of 300 kWh/m 3 (specific energy of 903 kJ/kg) was achieved with a discharge rate of up to 1.3 kW thermal energy. The test results verified the high performance of the TATB and encouraged further development of this technology.

25 ENERGY STORAGE↗
DOE OSTI2023

Fluorinated High-Voltage Electrolytes To Stabilize Nickel-Rich Lithium Batteries

As state-of-the-art (SOA) lithium-ion (Li-ion) batteries approach their specific energy limit (~250 Wh kg -1 ), layer-structured, nickel-rich (Ni-rich) lithium transition metal oxide-based cathode materials, e. g., LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811), have attracted great interest owing to their practical high specific capacities (>200 mAhg -1 ). Coupled with their high average discharge voltages (~4 V vs Li/Li + ), Ni-rich cathode-based lithium batteries possess a great potential to achieve much higher specific energies (>350 Wh kg -1 at the cell level) than the SOA Li-ion counterparts. In addition, Ni-rich oxides are low-cost battery cathode materials due to their low cobalt contents. However, Ni-rich cathode-based lithium batteries suffer quick capacity degradations upon cycling, particularly at high upper cutoff voltages (e.g., ≥= 4.5 V vs Li/Li + ), due to crystal structure changes of the active cathode materials and parasitic side reactions at the electrolyte/electrode interfaces. In this study, a fluorinated-solvent-based, high-voltage stable electrolyte (HVE), i.e., 1 M Li bis(trifluoromethanesulfonyl)imide (LiTFSI) in fluoroethylene carbonate (FEC), bis(2,2,2-trifluoroethyl) carbonate (FDEC), and methyl (2,2,2-trifluoroethyl) carbonate (FEMC) with Li difluoro(oxalate)borate (LiDFOB) additive, was formulated and evaluated in Li/NMC811 battery cells. Further, to the best of our knowledge, this class of electrolyte has not been investigated for Ni-rich cathode-based lithium batteries. Li/NMC811 cells with HVE exhibited a superior long-term cycle performance stability, maintaining ~80% capacity after ~500 cycles at a high cutoff voltage of 4.5 V (vs Li/Li + ) than a baseline carbonate-solvent-based electrolyte (BE). The superior cycle stability of the Li/NMC811 cells is attributed to the inherently high-voltage stability of HVE, supported by the physical and electrochemical analyses. This conclusion is supported by our density functional theory (DFT) modeling where HVE shows a less tendency of deprotonation/oxidation than BE, leading to the observed cycle stability. The findings in this study are important to help tackle the technical challenges facing Ni-rich cathode-based lithium batteries to realize their high energy density potentials with a long cycle life.

25 ENERGY STORAGE↗
DOE OSTI2024

A weakly ion pairing electrolyte designed for high voltage magnesium batteries

High-voltage rechargeable magnesium batteries (RMBs) are potential alternatives to lithium-ion batteries owing to the low cost and high abundance of magnesium. However, the parasitic reactions of the latter with many electrolytes greatly hinders the stability and kinetics of Mg plating/stripping. Here we report a new and easily accessible solvent-designed electrolyte, which effectively solves the difficulty of ion pair dissociation and facilitates fast nanoscale Mg nucleation/growth using simple Mg(TFSI)2 as the salt, enabling a facile interfacial charge transfer process. Dendrite-free Mg plating/stripping is maintained for over 7000 hours (∼10 months) at a practical areal capacity of 2 mA h cm−2. The high-voltage stability of these electrolytes is demonstrated by benchmarking with polyaniline||Mg full cells with an operating voltage up to 3.5 V that exhibit stable cycling at a 2C rate with 99% coulombic efficiency after 400 cycles. This work opens up new frontiers in coupling low-cost electrolytes with next-generation high-voltage cathode materials for fast-charging RMBs with long life and high energy densities.

Li, Chang↗
DOE OSTI2020

ELM Suppression by Boron Powder Injection and Comparison with Lithium Powder Injection on EAST

Type I edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST) were completely suppressed via boron powder injection into the X-point region of an upper-single null configuration over a wide range of operating conditions (2.8 < P aux < 7.5 MW, 3.8 × 10 19 < n e < 6 × 10 19 m -3 , RF-only and RF + NBI heating scenarios, both grad-B drift directions, and even He ion majority plasmas) (Sun et al. in Nucl. Fusion, 2020). A window of edge B concentration for stable long pulse operation was identified: too low and ELMs return, too high and the discharge suffers radiative collapse. The injection of boron powder above the minimum for ELM suppression coincided with the occurrence of an edge harmonic oscillation detected in magnetics (both on the high-field side and low-field side), in AXUV diodes near the upper X-point, divertor Dα emission, and in a range of other diagnostics (Diallo et al. in: Proceedings of 2020 IAEA fusion energy conference, 2021). Furthermore, no harmonic oscillation was observed when ELMs were present, and stored energy was slightly increased at constant density during ELM suppression. Core tungsten emission during ELM suppression either increased or decreased relative to ELMy H-mode, but the W emission was maintained at acceptable levels. The threshold B injection rate was measured for several conditions, and found to increase with heating power. Li powder injection into comparable discharges also resulted in a short phase of ELM suppression, but density and stored energy both decreased due to the strong pumping effect of lithium; no edge harmonic oscillation was observed with Li injection, indicating that the ELM suppression mechanisms differ. The new set of B-seeded, ELM-suppressed discharges exhibited certain characteristics of quiescent H-mode (Burrell et al. in Phys Plasmas 8:2153, 2001), but did not require high shear, counter beams, etc. The wide operating window and compatibility with RF-only discharges paves the way for future experiments targeting long pulse H-mode discharges with complete ELM suppression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Development and Applications of an eReaxFF Force Field for Graphitic Anodes of Lithium-Ion Batteries

Graphene is one of the most promising materials for lithium-ion battery anodes due to its superior electronic conductivity, high surface area for lithium intercalation, fast ionic diffusivity and enhanced specific capacity. A reliable description of many battery processes requires an explicit description of electrochemical interactions involving electrons. A detailed atomistic modeling of electronic conduction and non-zero voltage simulations of graphitic materials require the inclusion of an explicit electronic degree of freedom. To enable large length- and time-scale simulations of electron conduction in graphitic anodes, we developed an eReaxFF force field concept describing graphitic materials with an explicit electron. The newly developed force field, verified against quantum chemistry-based data describing, amongst others, electron affinities and equation of states, reproduces the qualitative behavior of electron conductivity in pristine and imperfect graphitic materials at different applied temperatures and voltages. In addition, excess electron localization near a defect site estimated from eReaxFF simulations agree quite well with the corresponding density functional theory calculations. Here, our eReaxFF simulations show the initiation of lithium-metal-plating driven by electron transfer from the graphene surface to the exposed lithium ions demonstrating the method’s potential for studying lithium-graphene interactions with explicit electrons and explain many unresolved electrode and electrode-electrolyte interface processes.

25 ENERGY STORAGE↗
DOE OSTI2023

Assessing the Intrinsic Roles of Key Dopant Elements in High–Nickel Layered Oxide Cathodes in Lithium–Based Batteries

A rational compositional design is critical for utilizing LiNiO 2 -based cathodes with Ni contents > 90% as promising next-generation cathode materials. Unfortunately, the lack of a fundamental understanding of the intrinsic roles of key elements, such as cobalt, manganese, and aluminum, makes the rational compositional design of high-Ni cathodes with a limited range of dopants (<10%) particularly challenging. Here, with 5% single-element doped cathodes, viz., LiNi 0.95 Co 0.05 O 2 , LiNi 0.95 Mn 0.05 O 2 , and LiNi 0.95 Al 0.05 O 2 , along with undoped LiNiO 2 (LNO), the influences of the dopants are systematically examined through a control of cutoff charge energy density and a common practice of cutoff charge voltage. Comprehensive investigations into the electrochemical properties, combined with in-depth analyses of the structural and interfasial stabilities and electrolyte decomposition pathways through advanced characterizations, unveil the following: i) the intrinsic role of dopants regulates the cathode energy density or state-of-charge and, more critically, the occurrence of H2–H3 phase transition, which essentially dictates cyclability; ii) undoped LNO can be stabilized well with the avoidance of H2–H3 phase transition; and iii) Co provides more merits overall with an optimized electrochemical operating condition. Finally, this work provides guidance for the compositional design of high-energy-density high-Ni cathodes and sheds light on the challenges of removing Co.

25 ENERGY STORAGE↗
DOE OSTI2022

Rational solvent molecule tuning for high-performance lithium metal battery electrolytes

Electrolyte engineering improved cycling of Li metal batteries and anode-free cells at low current densities; however, high-rate capability and tuning of ionic conduction in electrolytes are desirable yet less-studied. In this study, we design and synthesize a family of fluorinated-1,2-diethoxyethanes as electrolyte solvents. The position and amount of F atoms functionalized on 1,2-diethoxyethane were found to greatly affect electrolyte performance. Partially fluorinated, locally polar –CHF 2 is identified as the optimal group rather than fully fluorinated –CF 3 in common designs. Paired with 1.2 M lithium bis(fluorosulfonyl)imide, these developed single-salt-single-solvent electrolytes simultaneously enable high conductivity, low and stable overpotential, >99.5% Li||Cu half-cell efficiency (up to 99.9%, ±0.1% fluctuation) and fast activation (Li efficiency >99.3% within two cycles). Combined with high-voltage stability, these electrolytes achieve roughly 270 cycles in 50-μm-thin Li||high-loading-NMC811 full batteries and >140 cycles in fast-cycling Cu||microparticle-LiFePO 4 industrial pouch cells under realistic testing conditions. The correlation of Li + –solvent coordination, solvation environments and battery performance is investigated to understand structure–property relationships.

25 ENERGY STORAGE↗
DOE OSTI2022

Suppressing Chemical Corrosions of Lithium Metal Anodes

In this study, the lithium metal anode is essential for next-generation high-energy-density rechargeable Li-metal batteries. Although extensive studies have been performed to prolong the cycle life of Li-metal batteries, the calendar life, which associates with the chemical corrosion of Li metal in liquid electrolytes, has not been quantitatively understood. Here, by combing the titration gas chromatography method and cryogenic focused ion beam, a quantitative relationship between the chemical corrosion rate and electrochemically deposited Li morphology in various liquid electrolyte systems is established. It has been identified that the corrosion rate is dominated by the porosity of the deposited Li. The larger the porosity of deposited Li has, the faster the corrosion rate will be. Strategies to mitigate the chemical corrosion on Li thus to extend the calendar life of Li-metal batteries are further proposed. By strictly controlling the stacking pressure during Li plating, Li deposits with ultra-low porosity can be achieved, suppressing the corrosion rate to 0.08 ± 0.16%/day compared with 1.71 ± 0.19%/day of the high-porosity Li.

25 ENERGY STORAGE↗
DOE OSTI2023

Mechanistic understanding of aging behaviors of critical-material-free Li 4 Ti 5 O 12 //LiNi 0.9 Mn 0.1 O 2 cells with fluorinated carbonate-based electrolytes for safe energy storage with ultra-long life span

Behind-the-meter storage (BTMS) systems - a viable method to minimize potential risk of blackout events and stabilize the grid - require a different type of cost-effective energy storage with excellent safety, ultra-long (>20 years) cycle life and reasonable energy density compared that of electric vehicles. To increase the energy density and reduce the cost of a long-term cyclable lithium-titanate-based cell, it is required to employ a critical-material-free high voltage cathode and an electrolyte with good electrochemical and transport properties. In this report the long-term electrochemical performance and behaviors of selected critical-material-free Li 4 Ti 5 O 12 (LTO)//LiNi 0.9 Mn 0.1 O 2 (LNMO) full cells for BTMS applications are evaluated and analyzed in the optimized voltage range of 1.4-2.7 V at 45 degrees C with different fluorinated carbonate-based electrolytes. The fluoroethylene carbonate (FEC)-based electrolyte cell shows the highest capacity retention of 57.9% and Coulombic efficiency (CE) of 99.96% after 1000 cycles, potentially attributed to a dense, homogenous and less resistive LiF-rich solid-electrolyte interphase (SEI) layer formed on the surface of LTO that may mitigate electrolyte decomposition and maintain relatively low cell impedance during cycling. The 3,3,3-fluoroethylmethyl carbonate (F-EMC)-based electrolyte cell, however, presents the worst performance with lower capacity and a sharp decrease of CE, due to unstable and non-uniform SEI formation and continuous oxidative electrolyte decomposition. This mechanistic understanding of cell aging behaviors and failure mechanisms with detailed analysis of surface chemistry and electrode morphology can guide design of new electrode chemistries and electrolyte formulations for the development of BTMS batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Tailoring Interfaces in Solid-State Batteries Using Interfacial Thermochemistry and Band Alignment

Solid-state lithium ion batteries have enhanced thermal stability compared to batteries using liquid electrolytes. Although their practical implementation is limited by undesired side reactions between the electrode and electrolyte, different modification strategies have been proposed to stabilize these reactive interfaces. These approaches have been primarily based upon bulk materials properties, however, which may not necessarily be representative of the chemistry at the solid/solid interface. In this work, first principles calculations and X-ray scattering experiments are used to elucidate molecular-level reactivity and develop design principles for tailored interfaces based on surface and interfacial properties. Because of its well-known instability, the interface between the Li metal anode and the lithium lanthanum titanate (LLTO) solid electrolyte is applied as a model system. Density functional theory calculations are used to describe bulk, surface, and interfacial thermochemistry of the Li/LLTO system, and interfacial reconstruction is probed using ab initio molecular dynamics. These simulations of the Li/LLTO interface demonstrate facile decomposition concomitant with reduction of Ti 4+ ions. Based on further insights from computational analysis of the surface band edge positions, La 2 O 3 is proposed as an interlayer coating and is shown to provide an energetic barrier for interfacial charge transfer and decomposition reactions from X-ray reflectivity measurements and theoretical calculations. The findings in this work suggest that design strategies based on surface and interfacial properties can be used to kinetically stabilize electrode/electrolyte interfaces in solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ion Size Effects on the Thermodynamic, Kinetic, and Mechanical Properties during Ion Exchange in Solid-State Electrolytes

Ion exchange offers a pathway to impose residual compressive stresses to mitigate the electro-chemo-mechanical cracking of solid-state electrolytes such as lithium lanthanum zirconium oxide. This study uses a coupled multiscale framework (integrating density functional theory (DFT), molecular dynamics (MD), and continuum modeling) to examine how exchange ion size influences stress, diffusion, fracture toughness, and electronic properties. Larger isovalent ions (Na + , Ag + , K + ) were exchanged with Li + , with DFT confirming their preference for octahedral 96h sites and a linear relationship between ion size and chemical free expansion coefficient. MD simulations reveal stress and concentration effects on exchange ion diffusivity at elevated temperatures, with Na + and Ag + maintaining favorable mobility while K + showing concentration-dependent clustering. Continuum modeling predicts the range of fracture strength improvements and the required ion exchange concentration profile. It was shown that a 5% surface exchange concentration can induce ∼0.6 GPa of surface compressive stress using Na + and ∼1.0 GPa of surface compressive stress using Ag + . On the other hand, larger ion exchange species may penalize Li + diffusivity by increasing the activation volume and activation energy. Interestingly, Na + has a negligible penalty on Li-ion diffusivity. The room temperature Li + ion diffusivity is reduced by ∼40% with Ag + ion exchange. Electronic band structure analysis shows no size-dependent change in the bandgap, though Ag + introduces localized defect states near the valence band maximum. This study highlights ion size as a key factor in optimizing LLZO properties, offering a framework to improve the solid-state battery performance.

Jagad, Harsh D. [Brown Univ., Providence, RI (Unit↗
DOE OSTI2021

Limiting Current in Nanostructured Block Copolymer Electrolytes

The next-generation electrolytes for lithium batteries must be able to conduct ions at sufficiently high current densities; yet this regime is rarely studied directly. The limiting current density of an electrolyte quantifies the highest possible rate of ion transport under an applied dc potential. Herein, we report on the limiting current density in twelve nanostructured polystyrene-block-poly(ethylene oxide) (PS-b-PEO, or SEO) copolymer electrolytes. We find that the limiting current at a given salt concentration increases systematically with increasing volume fraction of the PEO block (φ EO ). In contrast, the effective-medium theory, commonly used to analyze conductivity in block copolymer electrolytes, predicts that limiting current is independent of φ EO . To resolve this conundrum, the ionic conductivity, the mutual diffusion coefficient of the salt, and the steady-state current fraction of the block copolymer electrolytes were measured. These measurements enable predictions of limiting current with no adjustable parameters using the concentrated solution theory. We found quantitative agreement between experimentally measured limiting current densities and predictions based on the concentrated solution theory. This work sheds light on how to reliably measure and predict limiting current density in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2026

Anode-less Solid-State Li–S Batteries Enabled by Fe-Stabilized Polysulfides

Anode-less solid-state lithium-sulfur batteries (SSLSBs) with lithium sulfide (Li 2 S) as the cathode promise a high energy density and ease of manufacturing. However, Li 2 S is plagued by poor conductivity, sluggish activation kinetics, and a poor cycle life. Here, in this study, we report an FeCl 3 -activated Li 2 S (FLS) cathode with solid-state polysulfide intermediates generated through a redox reaction between FeCl 3 and Li 2 S. This strategy is shown to boost the electrical conductivity of Li 2 S by 7 orders of magnitude and lower the activation barrier. During cycling, Fe plays a significant role in stabilizing the highly active polysulfide species, contributing to the exceptional electrochemical performance. The FLS cathode achieves 80% capacity retention over 500 cycles with >99% Li 2 S utilization. Furthermore, a Li-metal-free (anode-less) full cell retained over 80% of its initial capacity after 240 cycles. This work underscores the promise of leveraging Fe-stabilized polysulfides in enabling high-energy, long-lasting, solid-state Li-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Vibrational Entropy Contribution to Mixing Free Energy of Ni-Rich LiNi 1- y Co y O 2

First principles density-functional-theory calculations are performed of the mixing free energy of the layered oxide LiNi 1-y Co y O 2 , a model Li-ion-battery cathode material, at 1000 K. Analysis of internal energy, LN exchange, configurational entropy and vibrational entropy are combined to obtain the net mixing free energy. The vibrational entropy requires a more indirect treatment than the other terms; analysis based on heat capacity is presented here, to show that the vibrational entropy is of comparable magnitude to the configurational entropy, and it tends to promote solid-solution behavior in LiNi 1-y Co y O 2 .

25 ENERGY STORAGE↗
DOE OSTI2023

High-Performance Low-Cobalt Cathode Materials for Li-ion Batteries

The layer-structured Li[Ni x Co y Mn 1-x-y ]O 2 (NCM) cathode materials have been the best choice for increasing electric vehicle driving distance per charge. The high Ni layered oxide represents successfully commercialized NCM cathodes (such as NCM622 and NCA) in lithium-ion batteries (LIBs) for EV applications due to their high energy density and acceptable cycling stability. However, the price of cobalt, the key element within LIBs for stability, has nearly tripled over the past few years due to increased demand from the cell phone industry. As mentioned in the DOE Funding Opportunity Announcement, the current materials shortage will also cause speculation for a future global shortage. Therefore, to meet the requirement and sustainability of the next-generation long-range and low-cost EVs, developing cathode materials with low-Co content to achieve higher energy density and lower cost is both essential and urgent. The overarching objective of this work is to develop stabilized NCM cathode materials with low Co content (namely LiNi x Co y Mn 1-x-y O 2 , y ≤ 0.04) to meet DOE’s goal of reducing Co loading below 50 mg Wh -1 while maintaining energy density greater than 600 Wh kg -1 based on cathode material. Via various dopings and coatings scalable methods, we explored and enhanced the cycling performance of low-cobalt cathodes. The final obtained NCM cathodes paired with graphite anode aim to deliver batteries with a high initial specific energy density of over 240 Wh kg -1 and a low capacity fading rate of less than 20% in 1000 cycles under a C/3 discharge rate. To accomplish this goal, a multidisciplinary team with several co-investigators has been formed from three organizations: The Pennsylvania State University (PSU), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL). The PI and co-investigators are Dr. Donghai Wang (PI) from PSU with expertise in the synthesis of nanostructured materials and manipulation of interfacial properties of electrochemically active materials, Dr. Jagjit Nanda, with substantial knowledge of and expertise in state-of-the-art cathodes from ORNL, Dr. Chao-Yang Wang with significant experience in advanced cell design and fabrication and cell diagnostics from PSU, and Dr. Chongmin Wang with world-wide known expertise of advance atomic scale characterization of electrode materials from PNNL. Furthermore, this project will leverage and synergistically work with the current DOE-funded programs on battery materials at PSU and ORNL and electrode materials characterization at PNNL. During this funded period, we have accomplished milestones stated as follows: • Scale up production of LiFePO 4 (LFP) coated NCM811 with a production of 300g/batch. Fifteen (≥2 Ah) pouch cells with LFP-coated NCM811 cathode are delivered. Self-evaluated pouch cells in PSU show superior over 80% capacity retention performance even after 1500 cycles at C/3 rate. • Various cations (Al, Ti, Zr, and Mo) substitute cobalt in low-cobalt partially and Co-free cathodes. Their effects on crystal structure and electrochemical behavior are explored. • Phosphate compounds as coating materials represent promising surface protection precursors for low-cobalt cathode materials. Therefore, several metal phosphates were selected for improving the NMC cycling performance and are regarded as effective approaches for a scalable and practical surface protection method. • Production of NCM92, where Nickel content is 92% among transition metals, is scaled up from synthesis to coating and heat treatment procedures. Fifteen 2.7Ah pouch cells with Ti-doped NCM92 cathodes and industrial graphite anode are delivered to Idaho National Lab for testing.

25 ENERGY STORAGE↗