SEARCH · Engineering Papers

Results for “conversion efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Pilot production and testing of high efficiency wraparound contact solar cells

Modifications were made to the process sequence until a device capable of high performance and satisfactory processing yields could be fabricated on a production line. Pilot production resulted in a 2 x 4 cm screen printed dielectric wraparound contact solar cell with average 28 C, Air Mass Zero (AMO) conversion efficiencies of 14.2% and reasonable process yields. This high performance was obtained with two different back contact configurations, making the device acceptable for many applications.

Gillanders, M.↗

NASA NTRS2001

Power and Efficiency Optimized in Traveling-Wave Tubes Over a Broad Frequency Bandwidth

A traveling-wave tube (TWT) is an electron beam device that is used to amplify electromagnetic communication waves at radio and microwave frequencies. TWT's are critical components in deep space probes, communication satellites, and high-power radar systems. Power conversion efficiency is of paramount importance for TWT's employed in deep space probes and communication satellites. A previous effort was very successful in increasing efficiency and power at a single frequency (ref. 1). Such an algorithm is sufficient for narrow bandwidth designs, but for optimal designs in applications that require high radiofrequency power over a wide bandwidth, such as high-density communications or high-resolution radar, the variation of the circuit response with respect to frequency must be considered. This work at the NASA Glenn Research Center is the first to develop techniques for optimizing TWT efficiency and output power over a broad frequency bandwidth (ref. 2). The techniques are based on simulated annealing, which has the advantage over conventional optimization techniques in that it enables the best possible solution to be obtained (ref. 3). Two new broadband simulated annealing algorithms were developed that optimize (1) minimum saturated power efficiency over a frequency bandwidth and (2) simultaneous bandwidth and minimum power efficiency over the frequency band with constant input power. The algorithms were incorporated into the NASA coupled-cavity TWT computer model (ref. 4) and used to design optimal phase velocity tapers using the 59- to 64-GHz Hughes 961HA coupled-cavity TWT as a baseline model. In comparison to the baseline design, the computational results of the first broad-band design algorithm show an improvement of 73.9 percent in minimum saturated efficiency (see the top graph). The second broadband design algorithm (see the bottom graph) improves minimum radiofrequency efficiency with constant input power drive by a factor of 2.7 at the high band edge (64 GHz) and increases simultaneous bandwidth by 500 MHz.

Wilson, Jeffrey D.↗

DOE OSTI2020

Technology Demonstration of a High-Pressure Swirl Oxy-Coal Combustor

This technical report presents the exploration of the design and prototyping of a High-Pressure Swirl Oxy-coal Combustor. Pressurized oxy-coal combustion systems have the potential to improve efficiency along with an increased carbon capture rate. Reduction of flue gas at higher pressure, smaller system size, and capital cost reductions render high-pressure oxy-coal systems particularly attractive as next-generation energy-producing systems. High-pressure oxy-coal combustion systems are a recent concept, and thus operability issues of combustor designs for such systems are not fully understood. Significant challenges exist to maintain oxy-coal combustion stability at elevated pressure and a high CO 2 diluent environment. Although a body of knowledge exists for high-pressure oxygen combustion in rocket engines (or similar applications), it is yet to be strategized how these fundamental concepts can be translated to low-temperature CO 2 diluent combustion regimes. The realization of the pressurized oxy-coal based systems requires combustor components to be designed and demonstrated for an operating pressure over 10 bar. However, pressurized oxy-coal combustor design information at this pressure range and scale relevant to validate those proposed systems is currently limited. Experimental data from MWth scale oxy-coal combustors are needed to identify the optimal trade-off between net efficiency and systems size. The proposed effort is aimed at demonstrating a 1 MWth down-fired swirl Oxy-Coal combustor and investigate the interrelation between combustor operating conditions (pressure; flame stability; flue gas recirculation ratio) and conversion efficiencies to minimize oxygen requirements. One of the key challenges is to configure burner design (i.e., swirl number and injector) and operating conditions for high-pressure oxy-coal combustion systems. These experiments differ from current systems partly due to the high theoretical flame temperature and related burner operability issues associated with oxy-combustion. An ASPEN PLUS® model study for 550 MWe TIPS and ENEL pressurized oxy-coal systems with CO 2 recirculation was performed to evaluate system design, subsystems sizing, and operating condition determination. The system analysis effort included TRL and technology gap determination of subsystems and critical components. This information was scaled to develop design requirements (design pressure and flue gas recirculation: RR Flue Gas = $\frac{m_{flue}}{m_{total}}$) for the 1 MWth combustor. The effects of a wide range of carbon dioxide recirculation ratios on the thermal efficiency of ENEL and TIPS cycles are studied. The pressure of 10 bar and 80 bar are used for ENEL and TIPS cycles, respectively. The thermal efficiency of ENEL is significantly higher than the efficiency of TIPS at a pressure of less than 10 bar. The insights from system analysis were then used to design a 1 MWth swirl oxy-coal combustor. Flame temperature analysis and material strength analysis was performed to determine the combustor thickness. The structural integrity of the combustor was validated by finite element analysis using Abacus® and Hypermesh®. Feasibility of igniters and secondary burners are investigated in successful high-pressure oxy-methane combustion. The secondary burners are designed in such a way that it can operate between 100 to 500 kW firing input. Three generations of the pintle injector were designed based on swirl numbers (S=0, 0.9, and 1.2). Key pintle injector parameters such as pintle size, pintle orifice size, spray pattern were investigated by cold flow tests. Information from these tests was used to modify injector design for smooth and successful operation. A 5 mm pintle orifice size was decided upon as the optimum size for oxy-coal operation for the combustor. Shadow sizing experiments were performed to identify the atomization rate of each injector. Different coal water slurry mixtures (30 – 50% coal by wt% in the mixture) at various total momentum ratios (TMR) were investigated for this purpose. These experiments provided decisive information to choose the best design of the injector. The injector with 1.2 swirl provided higher atomization in all cases than other designs. The mean equivalent droplet size of the jet was similar at different TMR and mixture ratios using this injector, thus making it suitable for use in most cases. Therefore, the 1.2 swirl-pintle injector was chosen for the shakedown test. The combustor and other sub-systems, including feed systems and control and data acquisition, have been manufactured, assembled, and integrated. The total system integration and installation began on July 1, 2020. The shake-down tests and initial operational capability demonstration are expected to be completed by September 30, 2020.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Techno-Economic Analysis of a Thermally Integrated Solid Oxide Fuel Cell and Compressed Air Energy Storage Hybrid System

Natural-gas-fueled solid oxide fuel cell (SOFC) systems have the potential for high-efficiency conversion of carbon to power due to the underlying electrochemical conversion process while readily facilitating carbon capture through the separation of the fuel and oxidant sources. Compressed air energy storage (CAES) technology can potentially store significant quantities of energy for later use with a high round-trip efficiency and lower cost when compared with state-of-the-art battery technology. The base load generation capability of SOFC can be coupled with CAES technology to provide a potentially flexible, low-carbon solution to meet the fluctuating electricity demands imposed by the increasing share of intermittent variable renewable energy (VRE) production. SOFC and CAES can be hybridized through thermal integration to maximize power output during periods of high electrical demand and then store power when either demand is low or renewable generation reduces power prices. The techno-economics of a low-carbon hybrid SOFC and CAES system was developed and investigated in the present study. The proposed hybrid system was found to be cost-competitive with other power-generating base-load facilities when power availability was considered. The hybrid system shows increased resilience to changes in a high VRE grid market scenario.

25 ENERGY STORAGE↗

NASA NTRS1991

Characterisation of frequency doubling in Eu(2+) doped aluminosilicate fibres

The results of a series of experiments on efficient second-harmonic generation in a fiber with a Eu(2+)-doped aluminosilicate core are reported. The fiber was prepared by the seeding method with CW mode-locked radiation at 1.06 micron and produced ultrastable peak conversion efficiencies of 0.001 during mode-locked readout. Experiments were performed to determine the IR preparation intensity dependence, the stability of the output, and the type of erasure mechanisms which occur. The results are compared with those of germanosilicate fibers and some similarities and differences are discussed.

Driscoll, T. J.↗

DOE OSTI2023

AN OVERVIEW OF THE DESIGN AND PERFORMANCE TESTING OF A 275 BAR INTEGRALLY GEARED SUPERCRITICAL CO2 COMPRESSOR FOR POWER GENERATION

An integrally geared compressor-expander (compander) for supercritical CO2 (sCO2) was developed to convert thermal energy to electricity. With operating pressures of 275 bar, this turbomachine represents the state of the art in integrally geared machine architecture, hitting compressor inlet densities of 600 kg/m3 and discharge pressures of 275 bar. The product development was funded by the Department of Energy’s Energy Efficiency and Renewable Energy Office under EE0007114 to advance the state of the art in concentrated solar power applications; however, the technology itself is agnostic to heat source, and is predicted to achieve a thermal-to-electric conversion efficiency of 50% for any indirect heat source capable of providing turbine inlet temperatures of 700°C or greater. While the program encompassed the design and testing for the compressor and turbine elements, this paper will focus on the compressor design and operation. The paper will begin with an introduction to the cycle design and analysis of an indirectly heated integrally geared sCO2 compander, a discussion of the mechanical and aerodynamic design of the compressor that is a two stage radial compressor operating subcritically at 27,512 rpm, and will then proceed to describe the test facility and measured data to characterize the performance and robustness of the machine. The paper will conclude with a discussion on lessons learned throughout the course of commissioning and testing. Practical aspects of testing a compressor operating near the dome including complications relating to obtaining an accurate compressor flow map, efficiency calculations, flow unsteadiness, and associated measurement uncertainties will be discussed.

wilkes, jason↗

NASA NTRS1985

High-efficiency double-heterostructure AlGaAs/GaAs solar cells

Double-heterostructure solar cells have been fabricated from wafers prepared by using organometallic chemical vapor deposition to grow a p GaAs absorbing layer sandwiched between p(+) and n(+) AlGaAs layers. The best cell, which incorporates an abrupt AlGaAs/GaAs shallow heterojunction, exhibits a global AM1 one-sun conversion efficiency of 23 percent. The rate at which the open-circuit voltage decreases with increasing temperature is lower for the double-heterostructure cells than for GaAs shallow-homojunction cells.

Gale, R. P.↗

NASA NTRS2009

Catalysts for Efficient Production of Carbon Nanotubes

Several metal alloys have shown promise as improved catalysts for catalytic thermal decomposition of hydrocarbon gases to produce carbon nanotubes (CNTs). Heretofore almost every experiment on the production of carbon nanotubes by this method has involved the use of iron, nickel, or cobalt as the catalyst. However, the catalytic-conversion efficiencies of these metals have been observed to be limited. The identification of better catalysts is part of a continuing program to develop means of mass production of high-quality carbon nanotubes at costs lower than those achieved thus far (as much as $100/g for purified multi-wall CNTs or $1,000/g for single-wall CNTs in year 2002). The main effort thus far in this program has been the design and implementation of a process tailored specifically for high-throughput screening of alloys for catalyzing the growth of CNTs. The process includes an integral combination of (1) formulation of libraries of catalysts, (2) synthesis of CNTs from decomposition of ethylene on powders of the alloys in a pyrolytic chemical-vapor-decomposition reactor, and (3) scanning- electron-microscope screening of the CNTs thus synthesized to evaluate the catalytic efficiencies of the alloys. Information gained in this process is put into a database and analyzed to identify promising alloy compositions, which are to be subjected to further evaluation in a subsequent round of testing. Some of these alloys have been found to catalyze the formation of carbon nano tubes from ethylene at temperatures as low as 350 to 400 C. In contrast, the temperatures typically required for prior catalysts range from 550 to 750 C.

Sun, Ted X.↗

DOE OSTI2022

Surface reaction for efficient and stable inverted perovskite solar cells

We report perovskite solar cells (PSCs) with an inverted structure (often referred to as the p-i-n architecture) are attractive for future commercialization due to their easily scalable fabrication, reliable operation, and compatibility with a wide range of perovskite-based tandem device architectures. However, the power conversion efficiency (PCE) of p-i-n PSCs falls behind n-i-p (or normal) structure counterparts. This large performance gap could undermine efforts to adopt p-i-n architectures, despite their other advantages. Given the remarkable advances in perovskite bulk materials optimization over the past decade, interface engineering has become the most important strategy to push PSC performance to its limit. Here, we report a reactive surface engineering approach based on a simple post-growth treatment of 3-(Aminomethyl)pyridine (3-APy) on top of a perovskite thin film. First, the 3-APy molecule selectively reacts with surface FA+, reducing perovskite surface roughness and surface potential fluctuations associated with surface steps/terraces. Second, the reaction product on the perovskite surface decreases the formation energy of charged iodine-vacancies, leading to effective n-type doping with a reduced work function in the surface region. With this reactive surface engineering, the resulting p-i-n PSCs obtained a PCE over 25%, along with retaining 87% of the initial PCE after over 2400 h of one-sun operation at about 55 degrees C in air.

14 SOLAR ENERGY↗

DOE OSTI2022

Quantum-Cutting Luminescent Coatings for High-Efficiency, Low-Cost Solar Cells (Final Technical Report)

The objective of the project is to optimize the deposition and post-deposition annealing conditions of quantum-cutting materials to enable coatings with high photoluminescence quantum yields and optimal absorption onset. These coatings will be integrated with commercial solar photovoltaic cells to enable improved power conversion efficiency, and the quantum-cutting cell stability will be ensured using industry-standard packaging methods.

14 SOLAR ENERGY↗

NASA NTRS2001

The HP 85192B EEFet3 GaAs FET Nonlinear Model Used in the High Efficiency Microwave Power Amplifier (HEMPA)

Most nonlinear circuit analysis programs that exist today were designed primarily for transient analysis. By incorporating more accurate models in simulation programs, accurate predictions of GaAs field effect transistors (FET) behavior can be accomplished. However, should the designer need to simulate GaAs FETs that operate at high DC-to-RF conversion efficiencies, a more sophisticated model is needed. A relevant and appropriate method is called harmonic-balance, as described by Quere et al.

Sims, William Herbert, III↗

DOE OSTI2021

Plastic waste upcycling toward a circular economy

Large amounts of plastics are discarded worldwide each year, leading to a significant mass of waste in landfills and pollution to soil, air, and waterways. Upcycling is an efficient way to transform plastic waste into high-value products and can significantly lessen the environmental impact of plastic production/consumption. In this article, current advances and future directions in plastic waste upcycling technologies are discussed. In particular, this review focuses on the production of high-value materials from plastic waste conversion methods, including pyrolysis, gasification, photoreforming, and mechanical reprocessing. Plastic waste compositions, conversion products, reaction mechanisms, catalyst selection, conversion efficiencies, polymer design, and polymer modification are also explored. Furthermore, the main challenges facing the adoption and scale-up of these technologies are highlighted. Suggestions are given for focusing future research and development to increase the efficiency of upcycling practices.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2024

Endothermic Charge Separation Occurs Spontaneously in Non–Fullerene Acceptor/Polymer Bulk Heterojunction

Organic photovoltaics (OPVs) based on non-fullerene acceptors (NFAs) have achieved a power conversion efficiency close to 20%. These NFA OPVs can generate free carriers efficiently despite a very small energy level offset at the donor/acceptor interface. Why these NFAs can enable efficient charge separation (CS) with low energy losses remains an open question. Here, the CS process in the PM6:Y6 bulk heterojunction is probed by time-resolved two-photon photoemission spectroscopy. It is found that the CS, the conversion from bound charge transfer (CT) excitons to free carriers, is an endothermic process with an enthalpy barrier of 0.15 eV. The CS can occur spontaneously despite being an endothermic process, which implies that it is driven by entropy. It is further argued that the morphology of the PM6:Y6 film and the anisotropic electron delocalization restrict the electron and hole wavefunctions within the CT exciton such that they can primarily contact each other through point-like junctions. Furthermore, this configuration can maximize the entropic driving force.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Environmental and Economic Assessments and Uncertainties of Multiple Lignocellulosic Biomass Utilization for Bioenergy Products: Case Studies

Life-cycle assessment (LCA) and techno-economic analysis (TEA) were applied to assess the economic feasibility and environmental benefits of utilizing multiple biomass feedstocks for bioenergy products under three different technological pathways with consideration of uncertainties. Three cases were studied for the production of pellets, biomass-based electricity, and pyrolysis bio-oil. A Monte Carlo simulation was used to examine the uncertainties of fossil energy consumption, bioenergy conversion efficiency, stochastic production rate, etc. The cradle-to-gate LCA results showed that pellet production had the lowest greenhouse gas (GHG) emissions, water and fossil fuels consumption (8.29 kg CO2 eq (equivalent), 0.46 kg, and 105.42 MJ, respectively). The conversion process presented a greater environmental impact for all three bioenergy products. When producing 46,929 Mg of pellets, 223,380 MWh of electricity, and 78,000 barrels of pyrolysis oil, the net present values (NPV) indicated that only pellet and electricity production were profitable with NPVs of $1.20 million for pellets, and $5.59 million for biopower. Uncertainty analysis indicated that pellet production showed the highest uncertainty in GHG emission, and bio-oil production had the least uncertainty in GHG emission but had risks producing greater-than-normal amounts of GHG. Biopower production had the highest probability to be a profitable investment with 85.23%.

09 BIOMASS FUELS↗

NASA NTRS2005

Liquid-Phase Deposition of Single-Phase Alpha-Copper-Indium-Diselenide

The success of exploratory missions in outer space often depends on a highly efficient renewable energy supply, as provided by solar cells. Figure 1 shows a well-known example: The robotic vehicle "Rover," constructed for NASA s "Mars Pathfinder" mission. The solar cells for such applications not only need to have high conversion efficiency, but must possess a high specific power, thus a high power output per unit mass. Since future missions will demand for large aggregates of solar cells and space flights are expensive, the solar cells must furthermore be available at low costs (per unit power output) and - very important in outer space - have a long lifetime and a high resistance against structural damage introduced by irradiation with high-energy electrons and protons.

Cowen, J.↗

NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash-to-Gas technologies show promise in addressing the need for a proper waste management system onboard a long-duration space mission. However, there is a clear need to better understand how the initial waste preparation can affect the overall conversion efficiency. Factors such as the waste size, moisture content, and packing density can have significant impacts on the reactor performance. This paper will focus on the effects of various pre-processing steps on the overall solid-to-gas conversion on the state of the art Trash-to-Gas system developed at NASA Kennedy Space Center. These results will help inform future Trash-to-Gas technologies on what types of supporting subsystems will be necessary to operate effectively for exploration missions.

Trash to Gas↗

NASA NTRSDate not supplied

Investigating Waste Preparation Methods for Trash-to-Gas Technologies

Trash to Gas↗

DOE OSTI2021

BETO 2021 Peer Review - Improving Formate Upgrading by Cupriavidus Necator 2.3.2.111

Formate can be generated by electrocatalytic reduction of CO2 and has been proposed as a soluble intermediate for the storage of carbon and energy. Biological systems capable of assimilating formate could enable conversion of formate generated from low-cost renewable energy and waste CO2 to myriad fuels and chemicals. To that end, the goal of this project is to develop the natural formatotroph Cupriavidus necator as a robust microbial chassis for efficient conversion of formate to value-added products. Using a combination of laboratory evolution and rational engineering, we have identified mutations and genetic deletions that improve its growth rate and biomass yield on formate by 1.2X. Using RNA-seq transcriptomics, we are elucidating the mechanisms that underly these improvements and anticipate this will contribute to our understanding of formate conversion. We have also engineered C. necator to convert formate to the potential polymer precursor 2-hydroxymuconate semialdehyde (2HMS) by introducing an exogenous pathway and deleting competing pathways and demonstrated production and robust growth using a pH-stat bioreactor. Final techno-economic analysis and life-cycle assessment on biological production of 2HMS from formate will enable the DOE and other stake holders to evaluate the economic and environmental impact of this project and related technologies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗