Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compressible flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Prospects for Nonlinear Laser Diagnostics in the Jet Noise Laboratory

Two experiments were conducted to test whether optical methods, which rely on laser beam coherence, would be viable for off-body flow measurement in high-density, compressible-flow wind tunnels. These tests measured the effects of large, unsteady density gradients on laser diagnostics like laser-induced thermal acoustics (LITA). The first test was performed in the Low Speed Aeroacoustics Wind Tunnel (LSAWT) of NASA Langley Research Center's Jet Noise Laboratory (JNL). This flow facility consists of a dual-stream jet engine simulator (with electric heat and propane burners) exhausting into a simulated flight stream, reaching Mach numbers up to 0.32. A laser beam transited the LSAWT flow field and was imaged with a high-speed gated camera to measure beam steering and transverse mode distortion. A second, independent test was performed on a smaller laboratory jet (Mach number < 1.2 and mass flow rate < 0.1 kg/sec). In this test, time-averaged LITA velocimetry and thermometry were performed at the jet exit plane, where the effect of unsteady density gradients is observed on the LITA signal. Both experiments show that LITA (and other diagnostics relying on beam overlap or coherence) faces significant hurdles in the high-density, compressible, and turbulent flow environments similar to those of the JNL.

Herring, Gregory C.↗
NASA NTRS1991

Second-order closure models for supersonic turbulent flows

Recent work on the development of a second-order closure model for high-speed compressible flows is reviewed. This turbulent closure is based on the solution of modeled transport equations for the Favre-averaged Reynolds stress tensor and the solenoidal part of the turbulent dissipation rate. A new model for the compressible dissipation is used along with traditional gradient transport models for the Reynolds heat flux and mass flux terms. Consistent with simple asymptotic analyses, the deviatoric part of the remaining higher-order correlations in the Reynolds stress transport equations are modeled by a variable density extension of the newest incompressible models. The resulting second-order closure model is tested in a variety of compressible turbulent flows which include the decay of isotropic turbulence, homogeneous shear flow, the supersonic mixing layer, and the supersonic flat-plate turbulent boundary layer. Comparisons between the model predictions and the results of physical and numerical experiments are quite encouraging.

Speziale, Charles G.↗
NASA NTRS1982

Solution of viscous internal flows on curvilinear grids generated by the Schwarz-Christoffel transformation

The combination of an orthogonal, curvilinear coordinate generation procedure with a stable forward marching viscous flow solution technique is presently employed in the solution of flow fields for arbitrary, axisymmetric ducts. Coordinate generation is accomplished by means of both potential lines and plane potential flow streamlines. Since the coordinate streamlines approximate actual ones, the equations of motion for viscous compressible flow can be parabolized in order to solve for both the boundary layer and the core flow in a single streamwise pass. The method's versatility is demonstrated by two examples of viscous compressible swirling flow through complex radial gas turbine passages.

Anderson, O. L.↗
DOE OSTI2019

Detonation propagation for shock-driven, subsonic and supersonic confiner flow

In this work, we study the compressible flow dynamics of two-dimensional, steady detonation wave propagation in a high explosive (HE) confined by aluminium (Al) or stainless steel (SS), outside of which is an air layer. We examine how the thickness of the confinement affects the subsonic detonation driving zone structure (DDZ) and the detonation speed (D 0 ), demonstrating a strong dependence on whether the oblique shock-driven flow in the confiner is supersonic, as for SS, or subsonic, as for Al. A characteristic path analysis is used to examine the information flow from the material boundaries through the supersonic flow regions in both the HE and confiner that can impact the sonic surfaces bounding the subsonic flow regions. It is shown that the nature of gas-dynamic wave reflection off the SS–air or Al–air boundary can significantly influence the DDZ and D 0 .

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1991

Second-order closure models for supersonic turbulent flows

Recent work by the authors on the development of a second-order closure model for high-speed compressible flows is reviewed. This turbulence closure is based on the solution of modeled transport equations for the Favre-averaged Reynolds stress tensor and the solenoidal part of the turbulent dissipation rate. A new model for the compressible dissipation is used along with traditional gradient transport models for the Reynolds heat flux and mass flux terms. Consistent with simple asymptotic analyses, the deviatoric part of the remaining higher-order correlations in the Reynolds stress transport equation are modeled by a variable density extension of the newest incompressible models. The resulting second-order closure model is tested in a variety of compressible turbulent flows which include the decay of isotropic turbulence, homogeneous shear flow, the supersonic mixing layer, and the supersonic flat-plate turbulent boundary layer. Comparisons between the model predictions and the results of physical and numerical experiments are quite encouraging.

Speziale, Charles G.↗
NASA NTRS1991

On the linear stability of compressible plane Couette flow

The linear stability of compressible plane Couette flow is investigated. The correct and proper basic velocity and temperature distributions are perturbed by a small amplitude normal mode disturbance. The full small amplitude disturbance equations are solved numerically at finite Reynolds numbers, and the inviscid limit of these equations is then investigated in some detail. It is found that instability can occur, although the stability characteristics of the flow are quite different from unbounded flows. The effects of viscosity are also calculated, asymptotically, and shown to have a stabilizing role in all the cases investigated. Exceptional regimes to the problem occur when the wavespeed of the disturbances approaches the velocity of either of the walls, and these regimes are also analyzed in some detail. Finally, the effect of imposing radiation-type boundary conditions on the upper (moving) wall (in place of impermeability) is investigated, and shown to yield results common to both bounded and unbounded flows.

Duck, Peter W.↗
NASA NTRS1981

Computer program for aerodynamic and blading design of multistage axial-flow compressors

A code for computing the aerodynamic design of a multistage axial-flow compressor and, if desired, the associated blading geometry input for internal flow analysis codes is presented. Compressible flow, which is assumed to be steady and axisymmetric, is the basis for a two-dimensional solution in the meridional plane with viscous effects modeled by pressure loss coefficients and boundary layer blockage. The radial equation of motion and the continuity equation are solved with the streamline curvature method on calculation stations outside the blade rows. The annulus profile, mass flow, pressure ratio, and rotative speed are input. A number of other input parameters specify and control the blade row aerodynamics and geometry. In particular, blade element centerlines and thicknesses can be specified with fourth degree polynomials for two segments. The output includes a detailed aerodynamic solution and, if desired, blading coordinates that can be used for internal flow analysis codes.

Crouse, J. E.↗
NASA NTRS1983

Effects of flow separation and cove leakage on pressure and heat-transfer distributions along a wing-cove-elevon configuration at Mach 6.9

External and internal pressure and cold-wall heating-rate distributions were obtained in hypersonic flow on a full-scale heat-sink representation of the space shuttle orbiter wing-elevon-cove configuration in an effort to define effects of flow separation on cove aerothermal environment as a function of cove seal leak area, ramp angle, and free-stream unit Reynolds number. Average free-stream Mach number from all tests was 6.9; average total temperature from all tests was 3360 R; free-stream dynamic pressure ranged from about 2 to 9 psi; and wing angle of attack was 5 deg (flow compression). For transitional and turbulent flow separation, increasing cove leakage progressively increased heating rates in the cove. When ingested mass flow was sufficient to force large reductions in extent of separation, increasing cove leakage reduced heating rates in the cove to those for laminar attached flow. Cove heating-rate distributions calculated with a method that assumed laminar developing channel flow agreed with experimentally obtained distributions within root-mean-square differences that varied between 11 and 36 percent where cove walls were parallel for leak areas of 50 and 100 percent.

Deveikis, W. D.↗
NASA NTRS1991

Computation of saddle point of attachment

Low-speed flows over a cylinder mounted on a flat plate are studied numerically in order to confirm the existence of a saddle point of attachment in the flow before an obstacle, to analyze the flow characteristics near the saddle point theoretically, and to address the significance of the saddle point of attachment to the construction of external flow structures, the interpretation of experimental surface oil-flow patterns, and the theoretical definition of three-dimensional flow separation. Two numerical codes, one for an incompressible flow and another for a compressible flow, are used for various Mach numbers, Reynolds numbers, grid sizes, and numbers of grid points. It is pointed out that the potential presence of a saddle point of attachment means that a line of 'oil accumulation' from both sides of a skin-friction line emanating outward from a saddle point can be either a line of separation or a line of attachment.

Hung, Ching-Mao↗
NASA NTRS1994

Numerical comparison of convective heat transfer augmentation devices used in cooling channels of hypersonic vehicles

Hypersonic vehicles are exposed to extreme thermal conditions compared to subsonic aircraft; therefore, some level of thermal management is required to protect the materials used. Normally, hypersonic vehicles experience the highest temperatures in the nozzle throat, and aircraft and propulsion system leading edges. Convective heat transfer augmentation techniques can be used in the thermal management system to increase heat transfer of the cooling channels in those areas. The techniques studied in this report are pin-fin, offset-fin, ribbed and straight roughened channel. A smooth straight channel is used as the baseline for comparing the techniques. SINDA '85, a lumped parameter finite difference thermal analyzer, is used to model the channels. Subroutines are added to model the fluid flow assuming steady one dimensional compressible flow with heat addition and friction. Correlations for convective heat transfer and friction are used in conjunction with the fluid flow analysis mentioned. As expected, the pin-fin arrangement has the highest heat transfer coefficient and the largest pressure drop. All the other devices fall in between the pin-fin and smooth straight channel. The selection of the best heat augmentation method depends on the design requirements. A good approach may be a channel using a combination of the techniques. For instance, several rows of pin-fins may be located at the region of highest heat flux, surrounded by some of the other techniques. Thus, the heat transfer coefficient is maximized at the region of highest heat flux while the pressure drop is not excessive.

Maldonado, Jaime J.↗
NASA NTRS1996

Vapor Flow Patterns During a Start-Up Transient in Heat Pipes

The vapor flow patterns in heat pipes are examined during the start-up transient phase. The vapor core is modelled as a channel flow using a two dimensional compressible flow model. A nonlinear filtering technique is used as a post process to eliminate the non-physical oscillations of the flow variables. For high-input heat flux, multiple shock reflections are observed in the evaporation region. The reflections cause a reverse flow in the evaporation and circulations in the adiabatic region. Furthermore, each shock reflection causes a significant increase in the local pressure and a large pressure drop along the heat pipe.

Issacci, F.↗
NASA NTRS1985

An adaptive finite element procedure for compressible high speed flows

A practical finite element-based solution procedure for high-speed inviscid compressible flow problems is described. The method provides time-accurate solutions to the coompressible Euler equations, and is computationally more efficient than the one-step Taylor-Galerkin approach and better suited for implementation on the modern generation of vector computers. The method is coupled to an adaptive mesh refinement process that enables steady state solutions of improved quality to be obtained.

Loehner, R.↗
NASA NTRS1988

On the instability of hypersonic flow past a wedge

The instability of a compressible flow past a wedge is investigated in the hypersonic limit. Particular attention is given to the Tollmien-Schlichting waves governed by triple-deck theory though some discussion of inviscid modes is given. It is shown that the attached shock has a significant effect on the growth rates of Tollmien-Schlichting waves. Moreover, the presence of the shock allows for more than one unstable Tollmien-Schlichting wave. Indeed, an infinite discrete spectrum of unstable waves is induced by the shock, but these modes are unstable over relatively small but high frequency ranges. The shock is shown to have little effect on the inviscid modes considered by previous authors and an asymptotic description of inviscid modes in the hypersonic limit is given.

Cowley, Stephen↗
NASA NTRS1990

On the instability of hypersonic flow past a wedge

The instability of a compressible flow past a wedge is investigated in the hypersonic limit. Particular attention is paid to Tollmien-Schlichting waves governed by triple-deck theory though some discussion of inviscid modes is given. It is shown that the attached shock can have a significant effect on the growth rates of Tollmien-Schlichting waves. Moreover, the presence of the shock allows for more than one unstable Tollmien-Schlichting wave. Indeed an infinite discrete spectrum of unstable waves is induced by the shock, but these modes are unstable over relatively small but high frequency ranges. The shock is shown to have little effect on the inviscid modes considered by previous authors and an asymptotic description of inviscid modes in the hypersonic limit is given.

Cowley, Stephen↗
NASA NTRS2018

Aerodynamics and Aeroacoustic Sources of a Coaxial Rotor

Vehicles with coaxial, contra-rotating rotor systems (CACR) are being considered for a range of applications. Design parameters are identified that effect the fundamental aerodynamics and fluid dynamic features of a CACR in hover, vertical, and edgewise flight. Understanding the fluid dynamic features is a precursor to studying the aeroacoustics of a coaxial rotor. Rotor performance was computed initially using Navier-Stokes solver with prescribed blade section aerodynamic properties, the results validated against generic experimental test cases. Using a A 2D potential flow code and 2D OVERFLOW compressible-flow Navier-Stokes solver, the fluid dynamics of blade interactions was simplified and broken into a 2D blade crossing problem, with crossing locations and velocity fields from the rotor results to understand circulation, thickness, compressibility, shed vorticity, downwash, and viscosity effects. A calculation tool has been developed to identify time and location of blade overlap and BVI time location for CACR. Specific aerodynamic phenomena that occur for each noise source relevant to CACR are presented, along with computational tools to predict these occurrences.

Aeroacoustic↗
NASA NTRS2001

Thermal Analysis of a Carbon Fiber Rope Barrier for Use in the Reusable Solid Rocket Motor Nozzle Joint-2

This study provides for development and verification of analysis methods used to assess performance of a carbon fiber rope (CFR) thermal barrier system that is currently being qualified for use in Reusable Solid Rocket Motor (RSRM) nozzle joint-2. Modeled geometry for flow calculations considers the joint to be vented with the porous CFR barriers placed in the "open' assembly gap. Model development is based on a 1-D volume filling approach where flow resistances (assembly gap and CFRs) are defined by serially connected internal flow and the porous media "Darcy" relationships. Combustion gas flow rates are computed using the volume filling code by assuming a lumped distribution total joint fill volume on a per linear circumferential inch basis. Gas compressibility, friction and heat transfer are included in the modeling. Gas-to-wall heat transfer is simulated by concurrent solution of the compressible flow equations and a large thermal 2-D finite element (FE) conduction grid. The derived numerical technique loosely couples the FE conduction matrix with the compressible gas flow equations, Free constants that appear in the governing equations are calibrated by parametric model comparison to hot fire subscale test results. The calibrated model is then used to make full-scale motor predictions using RSRM aft dome environments. Model results indicate that CFR thermal barrier systems will provide a thermally benign and controlled pressurization environment for the RSRM nozzle joint-2 primary seal activation.

Clayton, J. Louie↗