Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effects of elevated temperature exposure on the residual stress state and microstructure of PVD Cr coatings on SiC investigated via in situ X-ray diffraction and transmission electron microscopy

Pure Cr coatings are being considered as corrosion-resistant layers for SiC-SiC f composite fuel cladding in light water reactors. The residual stress state and interdiffusion behavior of Cr coatings deposited on SiC substrates using bipolar high-power impulse magnetron sputtering (B-HiPIMS) and direct current impulse magnetron sputtering (DCMS) were studied using in situ X-ray diffraction experiments at 300 °C, 700 °C, and 1200 °C. After elevated temperature exposure, evolution of the coating microstructure and coating/substrate interdiffusion was characterized by transmission electron microscopy. The compressive residual stress of the dense B-HiPIMS coating at room temperature was gradually relieved at 300 °C, while the stress transitioned to a tensile state at 700 °C. Grain growth of the Cr coating and a Cr–SiC interdiffusion layer consisting of newly formed Cr–C and Cr–Si phases were observed in the B-HiPIMS coating after exposure at 700 °C. The phases in the interdiffusion layer were identified to be Cr 7 C 3 , Cr 3 Si, and Cr 5 Si 3 C x experimentally and by thermodynamic predictions. For the DCMS coating, however, changes in residual stress and microstructure at the elevated temperatures were limited by the inherent porosity and inhomogeneous structure of the as-deposited coating. At 1200 °C, both coating types interacted rapidly with the underlying SiC substrate in the early stages of the experiment. The results from this study suggest that the characteristics of the Cr coatings do not significantly change at the reactor operating temperature of 300 °C, while changes in microstructure and stress state are expected in off-normal conditions of 700 °C and 1200 °C. Finally the results from this study suggest the B-HiPIMS coating is best-suited as a protective coating for SiC fuel cladding.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Deformation behavior of crystalline/amorphous Al-Si nanocomposites with nanolaminate or nanofibrous microstructures

Deformation mechanisms in sputter-deposited crystalline Al/amorphous Si nanocomposites with nanolaminate or nanofibrous morphology are characterized by nanoindentation, micropillar compression testing and transmission electron microscopy (TEM). The nanofibrous composite having crystalline Al nanofibers with ~40–50 nm in length and 15–20 nm in diameter embedded in amorphous Si exhibits strain hardening to a maximum flow stress of 2.9 GPa and no shear band (SB) formation in compression up to plastic strain exceeding 24%. On the other hand, nanolaminate composite that is composed of 80 nm crystalline Al layers and 20 nm amorphous Si layers exhibits catastrophic SBs starting at plastic strains in the range of 5–10%. Cross-sectional TEM of the deformed samples reveals a high density of stacking faults and twin boundaries in Al nanofibers and no microshear bands in the nanofibrous composite, suggesting plastic deformation in amorphous Si phase and crystalline Al nanofibers. Further, molecular dynamics simulations revealed that the plastic deformation in amorphous Si phase in the cosputtered films could be favored by the decrease in flow strength of amorphous Si with increasing Al solute concentration trapped in Si.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Microstructure Investigation and Mechanical Properties of Coated Zircaloy Cladding

Accident Tolerant Fuel concepts have been developed and tested in diverse research programs presently around the world. Industry teams have developed proprietary coating compositions and geometries, but significant knowledge gaps exist in terms of the resulting properties of the coating and the cladding and how those components impact each other in reactor conditions. Furthermore, the national laboratory and university teams currently studying the industry concepts are limited in their ability to freely disseminate and discuss results obtained on commercial coatings. The Advanced Fuels Campaign is therefore working to develop an understanding of ‘generic’ coatings applied to commercial nuclear cladding alloys free of these constraints. This milestone report provides insights in the microstructure of a 7-micrometer Cr coating on Zircaloy-2 and a 5- micrometer coating on Zry-4 as reference materials. SEM and TEM methods were utilized to describe and identify the interface, while nanoindentation was used to determine hardness and E-Moduli of coating and cladding material. This milestone summarizes the acquired knowledge to build a necessary verified foundation for future simulation and qualification efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Incorporating PCM-enabled thermal energy storage into 3D printable cementitious composites

This paper delineates the feasibility of incorporating microencapsulated phase change materials (mPCM) into 3D printable cementitious composite materials. A comprehensive experimental program was carried out to evaluate the impacts of mPCM on the printability, microstructures, mechanical and thermal properties of cementitious 3D printing ‘inks’. Results showed that the mPCM affected the printability of the cementitious ink material based on its physical properties (e.g., particle size) and volume loading – at lower volume loadings, mPCM increased the flowability of the cementitious ink material while leading to increased compressive strength and thermal conductivity for the hardened printed material. However, further increase in mPCM dosage led to a decrease in printability and, therefore, decrease in compressive strength and thermal conductivity as compared to the reference mixture. Here the results also showed that the inclusion of mPCM influence the printing parameters. In general, the inclusion of higher volume contents of mPCM necessitates a higher extrusion rate to achieve a desirable extrudability. Lastly, a thermal network model was formulated for 3D printed mPCM charged building components (e.g., wall). The study shows that microencapsulated PCM materials have good potential to be used in 3D printable cementitious mixtures for improving the thermal and energy performance of 3D printed buildings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An inelastic homogenization framework for layered materials with planes of weakness

Many geologic materials have a composite structure, in which macroscopic mechanical behavior is determined by the properties, shape, and heterogeneous distribution of individual constituents. In particular, sedimentary rocks commonly exhibit a layered microstructure, with distinct bedding planes that can also form planes of weakness. In this work, we present a homogenization framework for modeling inelastic layered media. The proposed constitutive model allows for distinct micro-constitutive laws for each layer, explicit representation of layer distributions, as well as incorporation of imperfect bonding at the interface between adjacent layers. No a priori assumptions are needed regarding the specific constitutive models used for the layers and interfaces, providing significant modeling flexibility. The overall framework provides a simple and physically-motivated way of defining anisotropic material behavior as an emergent property of the layered microstructure. The model is calibrated using triaxial and true-triaxial experimental data to demonstrate its ability to describe anisotropic deformation and multiple modes of failure.

58 GEOSCIENCES↗
DOE OSTI2022

GAMBL – A dual-cooled fusion blanket using SiC-based structures

We describe a novel fusion reactor blanket concept called GAMBL – GA Modular BLanket. This design concept exploits the advantages of SiC-based structures while minimizing their limitations. Material microstructures are tailored for different functions throughout the first wall and blanket, including the use of graded W/SiC composites to enhance heat transfer capabilities and resist erosion at the plasma-facing surface. The design contains a decoupled first wall and breeding blanket, which we show can provide adequate tritium breeding. By decoupling the breeding part of the blanket, we can operate at very low PbLi breeder pressure and support gravity loads in simple, radiatively-cooled structural beams that do not contain coolant. First wall performance capabilities are enhanced by eliminating constraints imposed by the deep blanket. We have performed initial fluid, thermal, mechanical and neutronics analysis of this concept to show its capabilities to meet the design requirements. R&D needs are mostly related to materials development. Except for unique manufacturing needs, no new facilities are required beyond existing or planned facilities for the US base program on steel-based DCLL blankets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Synthesis of bulk reactive Ni–Al composites using high pressure torsion

Self-propagating exothermic reactions, for instance in the nickel-aluminum (Ni-Al) system, have been widely studied to create high performance intermetallic compounds or for in-situ welding. Their easy ignition once the phase spacing is reduced below the micron scale, makes top-down methods like high-energy ball milling, ideal to fabricate such reactive nanostructures. A major drawback of ball milling is the need of a sintering step to form bulk pieces of the reactive material. However, this is not possible, as the targeted reactions would already proceed. Therefore, we investigate the ability of high pressure torsion as an alternative process, capable to produce bulk nanocomposites from powder mixtures. Severe straining of powder mixtures with a composition of 50 wt% Ni and 50 wt% Al enables fabrication of self-reactive bulk samples with microstructures similar to those obtained from ball milling or magnetron sputtering. Additionally, samples deformed at ambient temperature are highly reactive and can be ignited significantly below the Al melting point, finally predominantly consisting of Al 3 Ni 2 and Al 3 Ni, independent of the applied strain. Although the reaction proceeds first at the edge of the disk, the strain gradient present in the disks does not prevent reaction of the whole sample.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deconvoluting the Effect of Chromium and Aluminum on the Radiation Response of Wrought FeCrAl Alloys After Low-Dose Neutron Irradiation

FeCrAl alloys have been extensively investigated over the past decade as a candidate material for accident-tolerant fuel cladding in light water reactors. Here, we have completed a first of its kind study where Al and Cr concentrations are varied systematically under neutron irradiation to elucidate the post irradiation microstructural and mechanical response as a direct result of alloying content. Neutron irradiations were performed on alloys with composition Fe-(10-13)Cr-(5-7)Al in wt.% at temperatures of 214, 357, and 557°C to a dose of ~1.8 dpa (displacements per atom). Dislocation loop sizes and dispersion characteristics did not show strong compositional dependence. However, there were noticeable effects of composition on the dispersion of Cr-rich α'-precipitates, particularly a decrease in number density with increasing Al content or a decrease in Cr content. The present results confirm previous studies indicating the Cr concentration in these precipitates is lower than that expected in binary FeCr alloys and that Al can act as a destabilizing alloying element for the deleterious α'-phase.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The strong influence of Ti, Zr, Hf solutes and their oxidation on microstructure and performance of Nb 3 Sn superconductors

The strong influence of Ti, Zr, Hf solutes and their oxidation on microstructure and performance of Nb 3 Sn superconductors Over the last few years a new type of Nb 3 Sn superconducting composite based on the internal oxidation approach has emerged and has demonstrated performance significantly superior to conventional Nb 3 Sn. It requires a supply of O and the use of a Nb alloy – Nb-X, where X is a solute element that can be selectively oxidized to form oxide particles within the Nb 3 Sn. Such oxide particles not only refine Nb 3 Sn grain size, but also have the proper size to act as artificial pinning centers (APC) directly restraining fluxon motion, and thus dramatically improve superconducting properties. In this article we show that the size and volume fraction of the oxide particles determine both the levels of grain refinement and the shift in the peak field of the flux pinning force (F p -B) curve. Additionally, we explore the factors influencing these microstructure and properties, which we find include: selection of the solute element X, solute content, O content, and heat treatment. For the selection of X, we searched the periodic table for all promising candidates but focused down on the group-IVB elements (Ti, Zr, Hf) here as the drawability of Nb 3 Sn wires made from Nb-Ti, Nb-Zr, and Nb-Hf alloys has been demonstrated in the past few decades. We found that while internally oxidizing Nb-1.5at.%Ti led to negligible grain refinement and F p -B peak shift, Nb-Zr alloys led to much more dramatic results, and internally oxidizing Nb-Hf alloys led to the strongest grain refinement and F p -B peak shift. For Hf alloying in particular, we compared our internal oxidation method with another method for grain refinement, which uses Hf alloying itself without oxidation, and found that internal oxidation led to much stronger grain refinement and F p -B peak shift. We also found that higher solute content and lower reaction temperature led to stronger grain refinement and F p -B peak shift. We conclude with a discussion of the possible mechanisms for the influence of these factors.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Multiphysics and Multiscale Modeling of Coupled Transport of Chloride Ions in Concrete

Chloride ions (Cl−)-induced corrosion is one of the main degradation mechanisms in reinforced concrete (RC) structures. In most situations, the degradation initiates with the transport of Cl− from the surface of the concrete towards the reinforcing steel. The accumulation of Cl− at the steel-concrete interface could initiate reinforcement corrosion once a threshold Cl− concentration is achieved. An accurate numerical model of the Cl− transport in concrete is required to predict the corrosion initiation in RC structures. However, existing numerical models lack a representation of the heterogenous concrete microstructure resulting from the varying environmental conditions and the indirect effect of time dependent temperature and relative humidity (RH) on the water adsorption and Cl− binding isotherms. In this study, a numerical model is developed to study the coupled transport of Cl− with heat, RH and oxygen (O2) into the concrete. The modeling of the concrete microstructure is performed using the Virtual Cement and Concrete Testing Laboratory (VCCTL) code developed by the U.S. National Institute of Standards and Technology (NIST). The concept of equivalent maturation time is utilized to eliminate the limitation of simulating concrete microstructure using VCCTL in specific environmental conditions such as adiabatic. Thus, a time-dependent concrete microstructure, which depends on the hydration reactions coupled with the temperature and RH of the environment, is achieved to study the Cl− transport. Additionally, Cl− binding isotherms, which are a function of the pH of the concrete pore solution, Cl− concentration, and weight fraction of mono-sulfate aluminate (AFm) and calcium-silicate-hydrate (C-S-H), obtained from an experimental study by the same authors are utilized to account for the Cl− binding of cement hydration products. The temperature dependent RH diffusion was considered to account for the transport of Cl− with moisture transport. The temperature and RH diffusion in the concrete domain, composite theory, and Cl− binding and water adsorption isotherms are used in combination, to estimate the ensuing Cl− diffusion field within the concrete. The coupled transport process of heat, RH, Cl−, and O2 is implemented in the Multiphysics Object-Oriented Simulation Environment (MOOSE) developed by the U.S. Idaho National Laboratory (INL). The model was verified and validated using data from multiple experimental studies with different concrete mixture proportions, curing durations, and environmental conditions. Additionally, a sensitivity analysis was performed to identify that the water-to-cement (w/c) ratio, the exposure duration, the boundary conditions: temperature, RH, surface Cl− concentration, Cl− diffusion coefficient in the capillary water, and the critical RH are the important parameters that govern the Cl− transport in RC structures. In a case study, the capabilities of the developed numerical model are demonstrated by studying the complex 2D diffusion of Cl− in a RC beam located in two different climatic regions: warm and humid weather in Galveston, Texas, and cold and dry weather in North Minnesota, Minnesota, subjected to time varying temperature, RH, and surface Cl− concentrations.

composite theory↗
DOE OSTI2023

Irradiation Effects on Stability of δ-UZr2 phase in U-50 wt% Zr Alloy

U-50wt%Zr is a candidate metallic nuclear fuel with potential application in light water reactors due to its excellent thermal properties and high radiation tolerance. The Zr-rich UZr fuels possess greater swelling resistance and fission gas release characteristics compared with U-rich UZr fuels. In this current study, the δ-phase U-50wt%Zr is proton irradiated at room temperature to 1 displacement per atom (dpa) to provide insights on phase stability under irradiation conditions. High resolution characterization of Transmission Electron Microscopy (TEM) and Atom Probe Tomography (APT) characterization techniques are used to elucidate microstructural changes due to irradiation. TEM and APT results show highly oriented bcc β-Zr-rich platelet precipitates nucleating adjacent to α-U phases inside the UZr 2 matrix. Formation of this platelet morphology is characteristic of Widmänstatten structure which can be attributed to a variety of factors such as differences in thermal expansion coefficient between the phases, grain size, alloy composition, and cooling rate. The phases present are distinctly different than those observed through in situ annealing, but irradiation accelerates diffusion and phase separation kinetics. These microstructural changes in U-50wt%Zr are different from those achieved by pure thermodynamic or high temperature heavy ion irradiation experiments. Finally, our work, together with previous ones, highlight the necessity to study the U-Zr phase diagram under non-equilibrium thermodynamics conditions to support this material's deployment as a viable nuclear fuel form.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanical properties and strengthening mechanisms of cold sprayed Al-Mg alloys

This paper investigates the mechanical properties and strengthening mechanisms of cold sprayed Al-Mg alloys as a function of Mg content. Cold spray (CS) is a solid-state deposition process that can be used as a repair technique for structural components. However, the limited ductility of cold sprayed materials is an unsettled issue in CS community. Herein, reproducible, and significantly increased elongation to failure (∼15%) in as-deposited conditions is reported in CS Al-Mg binary alloys with low Mg content (≤ 2.5 wt%). Furthermore, reducing Mg content down to 2.5 wt% in CS Al-Mg binary alloys demonstrated comparable mechanical strength to its wrought counterparts. Strengthening mechanisms were analyzed in wrought and CS Al-Mg alloys based upon microstructural characteristics, such as grain size, Mg solute concentration, and dislocation density. A quantitative evaluation of yield strength revealed that grain boundary strengthening is predominant in CS Al-Mg alloys as compared with their wrought counterparts. When comparing among CS Al-Mg binary alloys of different compositions, Mg solute concentration, and dislocation density governed mechanical strength. In conclusion, the underlying mechanism for the variation of mechanical properties and strengthening mechanisms is discussed in terms of these microstructural characteristics.

Additive manufacturing↗
DOE OSTI2026

Creep Performance of Novel Composite Heating Elements for Reheat Furnace Electrification

The iron and steel industry is critical for the modern world but is also very energy intensive and is a low margin industry. Hot rolling requires reheating steel slabs to ~1250 °C for hot rolling and involves yield loss due to scale formation. Electrification of this process using resistive heating could improve yield but is currently not possible due to the poor creep resistance of MoSi2 heating elements, which need to be operated well below their maximum temperatures when mounted horizontally. To solve this problem, novel MoSi2 composite heating elements with SiBCN ceramic reinforcements are being developed using high energy ball milling and spark plasma sintering. The creep performance of different heating elements and their corresponding microstructures and electrical properties will be presented.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing

Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.

Milligan, Brian K.↗
DOE OSTI2024

Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction

Laser additive manufacturing (AM) of reaction-based metal matrix composites (MMCs) involves highly complex and non-equilibrium material transformation behavior, including melting, dissolution, precipitation, and solidification. Yet, the dynamics and interplay of these phase transformation processes remain poorly understood, posing substantial challenges in identifying the microstructure formation mechanism, and predicting and controlling the microstructure in the printed parts. Here, in this study, we performed the in-situ X-ray diffraction experiment to characterize the phase evolution dynamics of the 316L + 10 vol.%TiC system during laser melting, which provides direct and quantitative insights of the complex phase reaction and evolution dynamics under rapid heating and cooling conditions relevant to additive manufacturing of reaction-based MMCs. Further in-depth thermodynamic and kinetic calculations revealed that most of the phase evolution behavior observed in the in-situ X-ray diffraction experiment cannot be solely explained by widely used equilibrium thermodynamic models, and diffusion-controlled nonequilibrium dissolution and precipitation kinetics must be considered to elucidate the complex phase evolution behavior, including incomplete TiC dissolution, and three-step TiC precipitation. The three distinct types of precipitates generate unique hierarchical TiC micro- and nanostructures, which enhances the yield strength from 513 MPa to 877 MPa by 71 %, tensile strength from 628 MPa to 1054 MPa by 68 %, and Young's modulus from 193 GPa to 221 GPa by 14 %. The findings of our research provide the knowledge foundation for the design of unique microstructures and advanced MMC materials through laser AM.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Circular Reprocessing of Thermoset Polyurethane Foams

Thermoset polyurethane (PU) foams are widely used in industrial applications, but they cannot be recycled by conventional melt reprocessing because of their cross-linked structures. The introduction of carbamate exchange catalysts converts thermoset PU into covalent adaptable networks (CANs), which are amenable to reprocessing at elevated temperatures. However, this approach has produced solid PU films, which have fewer uses and lower commercial demand. In this work, simultaneous reprocessing and refoaming of thermoset PU foams is demonstrated by leveraging the melt-processability of PU CANs and allowing cell growth by gas generation in a twin-screw extruder. The optimal operating temperature of the refoaming process is determined through chemical, thermal, and structural analysis of PU foam extrudates. The foam-to-foam extrusion process produces controllable, continuous, and uniform foam structures, as characterized by cell diameter and cell number density. Low-density PU foams are obtained through a process simulating injection molding. The compression properties of reprocessed PU foam are compared with as-synthesized PU foam to demonstrate efficacy of the refoaming processes. These results demonstrate that PU foams can be prepared through recycling while maintaining microstructural and chemical integrity. In the future, this strategy may be applied to thermoset PU foams of various chemical compositions and shows promise for scalability.

36 MATERIALS SCIENCE↗