SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technique for silicon crystal-ribbon growth from crucible, two inert wettable filaments dipped into silicon melt to guide growth of silicon sheet. Filaments clamped in place and tilted slightly away from each other and seed ribbon lowered into contact with melt to establish menisci between filaments.
Device for making small, precise rotation of objects in cramped spaces consists of V-groove machined in block of aluminum (or nylon) and flat, slotted bar clamped across groove. Device used to rotate lenses until in precise alinement with optical axis of injection laser.
Special wrench speeds nut and bolt assembly when insufficient room to hold nut behind bolthole with standard tool. C-clamp shaped box-andsocket-wrench assembly holds nut on blind side in alinement to receive bolt from open side.
Tests were carried out on 20 inch x 20 inch panels at different test conditions using free-free panels, clamped panels, and panels as installed in the KU-FRL acoustic test facility. Tests with free-free panels verified the basic equipment set-up and test procedure. They also provided a basis for comparison. The results indicate that the effect of installed panels is to increase the damping ratio at the same frequency. However, a direct comparison is not possible, as the fundamental frequency of a free-free panel differs from the resonance frequency of the panel when installed. The damping values of panels installed in the test facility are closer to the damping values obtained with fixed-fixed panels. Effects of damping tape, stiffeners, and bonded and riveted edged conditions were also investigated. Progress in the development of a simple interior noise level control program is reported.
Dynamic mechanical analysis instrumentation was used for the development of specific test methodology in the determination of engineering parameters of selected materials, esp. plastics and elastomers, over a broad range of temperature with selected environment. The methodology for routine procedures was established with specific attention given to sample geometry, sample size, and mounting techniques. The basic software of the duPont 1090 thermal analyzer was used for data reduction which simplify the theoretical interpretation. Clamps were developed which allowed 'relative' damping during the cure cycle to be measured for the fiber-glass supported resin. The correlation of fracture energy 'toughness' (or impact strength) with the low temperature (glassy) relaxation responses for a 'rubber-modified' epoxy system was negative in result because the low-temperature dispersion mode (-80 C) of the modifier coincided with that of the epoxy matrix, making quantitative comparison unrealistic.
A simple model to study low velocity transverse impact of thin plates made of fiber-reinforced composite material, in particular T300/5208 graphite-epoxy was discussed. This model predicts the coefficient of restitution, which is a measure of the energy absorbed by the target during an impact event. The model is constructed on the assumption that the plate is inextensible in the fiber direction and that the material is incompressible in the z-direction. Such a plate essentially deforms by shear, hence this model neglects bending deformations of the plate. The coefficient of restitution is predicted to increase with large interlaminar shear strength and low transverse shear modulus of the laminate. Predictions are compared with the test results of impacted circular and rectangular clamped plates. Experimentally measured values of the coefficient of restitution are found to agree with the predicted values within a reasonable error.
A heating and cooling apparatus capable of cyclic heating and cooling of a test specimen undergoing fatigue testing is discussed. Cryogenic fluid is passed through a block clamped to the speciment to cool the block and the specimen. Heating cartridges penetrate the block to heat the block and the specimen to very hot temperaures. Control apparatus is provided to alternatively activate the cooling and heating modes to effect cyclic heating and cooling between very hot and very cold temperatures. The block is constructed of minimal mass to facilitate the rapid temperature changes.
The finite element analysis of wrinkling membranes was investigated. The determination of stresses and deformations within large partly wrinkled membrane surfaces is a problem of significant technical interest in such areas as conceptual design and analysis of ultra lightweight spacecraft structures. A closed-form solution to an axisymmetric problem involving partial wrinkling of an inflated shallow membrane was obtained. In particular, a membrane in the shape of a sperical annulus was considered. The outer edge of the annulus was assumed to be fixed so that no displacements occur along the outer perimeter. The inner edge is assumed to be clamped to a rigid movable plug. Solutions for the complete stress, strain, and displacement fields under the assumption of inextensional material behavior are presented for the case of pure torsional loads applied to the plug, and for the case of pure axial loads applied to the plug.
Rayleigh's integral formula is evaluated numerically for planar radiators of any shape, with any specified velocity in the source plane using the fast Fourier transfrom algorithm. The major advantage of this technique is its speed of computation - over 400 times faster than a straightforward two-dimensional numerical integration. The technique is developed for computation of the radiated pressure in the nearfield of the source and can be easily extended to provide, with little computation time, the vector intensity in the nearfield. Computations with the FFT of the nearfield pressure of baffled rectangular plates with clamped and free boundaries are compared with the 'exact' solution to illuminate any errors. The bias errors, introduced by the FFT, are investigated and a technique is developed to significantly reduce them.
Clamped circular graphite/epoxy plates (25.4, 38.1, and 50.8 mm radii) with an 8-ply quasi-isotropic layup were analyzed for static-equivalent impact loads using the minimum-total-potential-energy method and the von Karman strain-displacement equations. A step-by-step incremental transverse displacement procedure was used to calculate plate load and ply stresses. The ply failure region was calculated using the Tsai-Wu criterion. The corresponding failure modes (splitting and fiber failure) were determined using the maximum stress criteria. The first-failure mode was splitting and initiated first in the bottom ply. The splitting-failure thresholds were relatively low and tended to be lower for larger plates than for small plates. The splitting-damage region in each ply was elongated in its fiber direction; the bottom ply had the largest damage region. The calculated damage region for the 25.4-mm-radius plate agreed with limited static test results from the literature.
The globally convergent quasi-Newton minimization algorithm and the homotopy algorithms are discussed in detail and their effectiveness in solving certain classes of highly nonlinear problems of structural analysis is demonstrated. The application of the double dogleg strategy controls the directions and step-lengths of the quasi-Newtonian algorithm and overcomes the problem of nonpositive definite Hessians being produced during the iteration process. The algorithms are applied to a centrally loaded clamped beam, the snap-through of a shallow arch, and a shallow reticulated dome.
Vibrational characteristics are determined for a previously unsolved class of problems, that of doubly-curved shallow shells having rectangular planforms, clamped along one edge and free on the other three. The solution procedure uses the Ritz method with algebraic polynomial trial functions. Convergence studies are made, and accurate frequencies and contour plots of mode shapes are presented for various curvature ratios, including spherical, circular cylindrical and hyperbolic paraboloidal shells. Particular emphasis is given to the effect of adding spanwise curvature to shells having chordwise curvature; numerous published references already exist for the case of zero spanwise curvature. The effects of changing aspect ratio, thickness ratio and Poisson's ratio are also studied.
Adaptation of diesel engine allows prestressed ceramic materials evaluated under realistic pressure, temperature, and stress without introducing extraneous stress. Ceramic specimen part of prechamber of research engine. Specimen held in place by clamp, introduces required axial compressive stress. Specimen -- cylindrical shell -- surrounded by chamber vented or pressurized to introduce requisite radial stress in ceramic. Pressure chamber also serves as safety shield in case speimen disintegrates. Materials under consideration as cylinder liners for diesel engines.
Impact damage in graphite/epoxy laminates was characterized and transient strain history during impact was correlated. The material investigated was AS-4/3501-6 graphite/epoxy. Eight-ply and sixteen-ply quasi-isotropic laminates of 45/0/-45/90 sub s and 45/0/-45/90 sub 2s layups were fabricated with strain gages embedded between plies during the strain gages and leads from the highly conductive graphite fibers. The specimens were circular plates 12.7 cm (5 in.) in diameter and clamped along their circumference. The specimens were impacted with a 185 gm impactor, dropped from heights of 1.20 m and 1.65 m. An accelerometer was attached to the back surface of the specimen opposite the impact point and was used to trigger the recording instrumentation. The transient strain data were recorded with an eight channel waveform digitizer capable of sampling data at 0.5 microsec intervals. The data were stored, processed, and plotted by means of a microcomputer. Transient strain data were correlated with results from ultrasonic inspection of the specimens.
The accuracy of the NASTRAN modal synthesis analysis was assessed by comparing it with full structure NASTRAN and nine other modal synthesis results using a nine-bay truss. A NASTRAN component mode transient response analysis was also performed on the free-free truss structure. A finite element method was developed for nonlinear vibration of beam structures subjected to harmonic excitation. Longitudinal deformation and inertia are both included in the formula. Tables show the finite element free vibration results with and without considering the effects of longitudinal deformation and inertia as well as the frequency ratios for a simply supported and a clamped beam subjected to a uniform harmonic force.
The geometric form of a space station is presented that includes a description of a plurality of modules and berthing hubs, joined by interconnections which are sideways connectable. The modules and hubs are fastened together in a triangular configuration in three dimensions. The interconnections include a pair of opposed, axially aligned, flanged ports and a clamp latch formed from a plurality of sections hinged along their length and extending circumferentially around the flanged ports. A hermetic seal is formed between the ports. A utilities connection channel extends between the ports. The channel has a shell with utilities connectors movable between an extended position to mating connectors in the modules and a withdrawn position. Assembly sequence and common module shell structure is detailed.
The useful life of the wire probe in an ultrasonic kidney stone disintegration instrument is enhanced and prolonged by attaching the wire of the wire probe to the tip of an ultrasonic transducer by means of a clamping arrangement. Additionally, damping material is applied to the wire probe in the form of a damper tube through which the wire probe passes in the region adjacent the transducer tip. The damper tube extends outwardly from the transducer tip a predetermined distance, terminating in a resilient soft rubber joint. Also, the damper tube is supported intermediate its length by a support member. The damper system thus acts to inhibit lateral vibrations of the wire in the region of the transducer tip while providing little or no damping to the linear vibrations imparted to the wire by the transducer.
This report contains the study of Low Velocity Transverse Impact Damage of graphite-epoxy T300/5208 composite laminates. The specimen, 100 mm diameter clamped plates, were impact damaged by a cantilever-type instrumented 1-inch diameter steel ball. Study was limited to impact velocity 6 m/sec. Rectangular strips, 50 mm x 125 mm, were cut from the impact-damage specimens so that the impact damage zone was in the center of the strips. These strips were tested in tension to obtain their residual strength. An energy dissipation model was developed to predict the residual strength from fracture mechanics concepts. Net energy absorbed I(a) was evaluated from coefficient of restitution concepts based on shear dominated theory of fiber-reinforced materials, with the modification that during loading and unloading the shear deformation are respectively elastic-plastic and elastic. Delamination energy I(d) was predicted by assuming that the stiffness of the laminate dropped due to debonding. Fiber-breakage energy, assumed to be equal to the difference of I(a) and I(d), was used to determine the residual strength. Predictions were compared with test results.