Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Direct numerical simulation of single-species and binary-species boundary layers at high pressure

Direct numerical simulations of single-species and binary-species temporal boundary layers at high pressure are performed. The main objective is to investigate flow physics in a binary-species boundary layer at high pressure, with special attention to mass diffusion. The working fluids are nitrogen in the single-species cases, and a mixture of nitrogen and methane in the binary-species cases. An investigation of mean profiles shows that velocity and temperature profiles have steep gradients near the wall, whereas the mass fraction profiles do not have a steep gradient. This result indicates that the similarity law between velocity, temperature and mass fraction does not hold true in the binary-species boundary layer. The comparison of turbulent fluctuations shows that the qualitative characteristics of velocity and temperature are similar to each other. In contrast, profiles of mass fraction fluctuations are largely different from those of velocity and temperature. This result indicates that mass diffusion is not similar to momentum and thermal diffusions in binary-species boundary layers.

Toki, Takahiko↗
NASA NTRS1984

Inlet boundary layer effects in an axial compressor rotor. I - Blade-to-blade effects

This paper discusses experimental data measured on the blading and downstream of an isolated compressor rotor with thick inlet endwall boundary layers. The objective of the study was to compare these results with data acquired previously with thin inlet boundary layers and to assess the impact of inlet boundary layer thickness on the secondary flow. Flow visualization results showed the powerful impact of the hub corner stall and how at the same near stall flow coefficient where with thin inlet boundary layers the blade was separated at midspan, with thick inlet boundary layers it was attached. It was also shown that while secondary flow was very weak, it did produce sufficient radial redistribution to cause an apparent negative loss at the blade root.

Wagner, J. H.↗
NASA NTRS1986

Tables for correcting airfoil data obtained in the Langley 0.3-meter transonic cryogenic tunnel for sidewall boundary-layer effects

Tables for correcting airfoil data taken in the Langley 0.3-meter Transonic Cryogenic Tunnel for the presence of sidewall boundary layer are presented. The corrected Mach number and the correction factor are minutely altered by a 20 percent change in the boundary layer virtual origin distance. The sidewall boundary layer displacement thicknesses measured for perforated sidewall inserts and without boundary layer removal agree with the values calculated for solid sidewalls.

Jenkins, R. V.↗
NASA NTRS1988

Effects of free-stream turbulence on turbulent boundary layers with mild adverse pressure gradients

The influence of near isotropic free-stream turbulence on the shape factors and skin friction coefficients of turbulent boundary layers is presented for the cases of zero and mild adverse pressure gradients. With free-stream turbulence, improved fluid mixing occurs in boundary layers with adverse pressure gradients relative to the zero pressure gradient condition, with the same free-stream turbulence intensity and length scale. Stronger boundary layers with lower shape factors occur as a result of a lower ratio of the integral scale of turbulence to the boundary layer thickness, and to vortex stretching of the turbulent eddies in the free-stream, both of which act to improve the transmission of momentum from the free-stream to the boundary layers.

Hoffmann, J. A.↗
NASA NTRS1989

The influence of free-stream turbulence on turbulent boundary layers with mild adverse pressure gradients

The influence of near isotropic free-stream turbulence on the shape factors and skin friction coefficients of turbulent boundary layers is presented for the cases of zero and mild adverse pressure gradients. With free-stream turbulence, improved fluid mixing occurs in boundary layers with adverse pressure gradients relative to the zero pressure gradient condition, with the same free-stream turbulence intensity and length scale. Stronger boundary layers with lower shape factors occur as a result of a lower ratio of the integral scale of turbulence to the boundary layer thickness, and to vortex stretching of the turbulent eddies in the free-stream, both of which act to improve the transmission of momentum from the free-stream to the boundary layers.

Hoffmann, J. A.↗
NASA NTRSDate not supplied

Computational Study of Low-Speed Boundary-Layer Laminar-Turbulent Transition over a 30º Swept Plate in a Channel

Reliable boundary-layer laminar-turbulent transition predictions are critical for the design of aircraft that use natural or controlled laminar flow to achieve low drag and better fuel efficiency. During cruise flight through low turbulence, the three-dimensional boundary layer over swept surfaces can transition prematurely due to stationary crossflow instabilities induced by surface roughness. Parabolized stability equations analyses have been successfully used to explain the different phases of the transition process under well controlled perturbations such as steps or discrete roughness elements. However, methodologies are still lacking to model the boundary layer receptivity to distributed random roughness, and the following non-linear instability stages leading to transition. For engineering applications, several semi-empirical methods based on linear amplification factors or local helicity have found growing adoption, but their reliability is limited by their level of simplification and the sparsity of data they are based on. To address this gap, a new study of the effect of distributed random surface roughness on crossflow transition was started, using a 30◦ swept plate as a test vehicle. The plate, which is mounted in the 2 Foot × 3 Foot Low-Speed Boundary-Layer Channel at the NASA Langley Research Center, has been tested with micro-scale roughness of varied geometry near the leading edge. In order to analyze the flow in the test section and prepare Direct Numerical Simulations with resolved roughness, Reynolds-Averaged Navier-Stokes (RANS) simulations of the flow over the plate installed in the wind tunnel test section were performed using the Langtry-Menter transition model with stationary crossflow extension. This paper presents the results of these simulations, with comparison to the experiment.

ARMD↗
NASA NTRS1984

Numerical simulation of boundary-layer transition

The transition to turbulence in boundary layers was investigated by direct numerical solution of the nonlinear, three-dimensional, incompressible Navier-Stokes equations in the half-infinite domain over a flat plate. Periodicity was imposed in the streamwise and spanwise directions. A body force was applied to approximate the effect of a nonparallel mean flow. The numerical method was spectra, based on Fourier series and Jacobi polynomials, and used divergence-free basis functions. Extremely rapid convergence was obtained when solving the linear Orr-Sommerfeld equation. The early nonlinear and three-dimensional stages of transition, in a boundary layer disturbed by a vibrating ribbon, were successfully simulated. Excellent qualitative agreement was observed with either experiments or weakly nonlinear theories. In particular, the breakdown pattern was staggered or nonstaggered depending on the disturbance amplitude.

Spalart, P. R.↗
NASA NTRS1993

Structure of turbulence in three-dimensional boundary layers

This report provides an overview of the three dimensional turbulent boundary layer concepts and of the currently available experimental information for their turbulence modeling. It is found that more reliable turbulence data, especially of the Reynolds stress transport terms, is needed to improve the existing modeling capabilities. An experiment is proposed to study the three dimensional boundary layer formed by a 'sink flow' in a fully developed two dimensional turbulent boundary layer. Also, the mean and turbulence field measurement procedure using a three component laser Doppler velocimeter is described.

Subramanian, Chelakara S.↗
NASA NTRS1987

Boundary layer simulator (BLIMPJ) improvement

Improvements were made to advance the current Boundary Layer Integral Matrix Procedure - Version J (BLIMPJ) containing previously modeled simplified calculation methods accounting for surface roughness, relaminarization, and thick boundary layer effects. These improvements have potential applications in the design of the future Orbit Transfer Vehicles (OTV) engines. The coded wall roughness module was validated successfully against measured data from the LeRC 60-15 degree half-angle conical nozzle. The relaminarization model was modified to include wall cooling and roughness based on a set of test data from the same nozzle. The model was compared against typical data sets for validation in different flow regimes. The thrust loss calculation for thick boundary layer effects was computerized where the iterations between TDK and BLIMPJ proceeded automatically until convergence was achieved. An example is given for a typical OTV nozzle with an area ratio 1293.

Praharaj, S. C.↗
NASA NTRS1972

An analysis of the relaxation of laminar boundary layer on a flat plate after passage of an interface with application to expansion-tube flows

The relaxation of the accelerating-gas boundary layer to the test-gas boundary layer over a flat plate in an expansion tube is analyzed. Several combinations of test gas and acceleration gas are considered. The problem is treated in two conically similar limits: (1) when the time lag between the arrival of the shock and the interface at the leading edge of the plate is very large, and (2) when this lag is negligible. The time-dependent laminar-boundary-layer equations of a binary mixture of perfect gases are taken as the flow-governing equations. This coupled set of differential equations, written in terms of the Lam-Crocco variables, has been solved by a line-relaxation finite-difference techniques. The results presented include the Stanton number and the local skin-friction coefficient as functions of shock Mach number and the nondimensional distance-time variable. The results indicate that more than 95 percent of the test-gas boundary layer exists over a length, measured from the leading edge of the plate, equal to about three-tenths of the distance traversed by the interface in the free stream.

Gupta, R. N.↗
DOE OSTI2024

Mechanisms and models of the turbulent boundary layers at transcritical conditions

Computational models for high-pressure transcritical turbulence in wall-modeled large-eddy simulation typically rely on wall-function models to overcome the need for resolving the boundary layer structures. However, the mechanisms and models of turbulent boundary layer at transcritical conditions remain poorly understood since the near-wall flow and heat transfer are significantly affected by the enhanced fluctuations and steep gradients in thermodynamic properties. Here, to address this issue, we study the mechanisms of transcritical turbulent boundary layers and wall-attached models at transcritical conditions. It is shown that the real-fluid variable-property effects are associated with the coupling between the near-wall cycle and the wall-normal coherent motions in the outer layer, resulting in the amplification of turbulent energy in the outer layer and noticeable energy transfer between the log-layer and the outer layer; hence, turbulence in the log-layer is modulated by the outer layer. Based on this underlying physical principle, we propose the characteristic velocity and length scales for the attached eddy at transcritical conditions, and extend the attached eddy model to transcritical turbulent boundary layers by introducing a mixed scaling that incorporates both inner and outer scalings. We show that the new characteristic scales and extended attached-eddy model perform well in characterizing the structures in transcritical turbulent boundary layers.

Li, Fangbo↗
NASA NTRS1990

Computation and turbulence modeling for three-dimensional boundary layers including turbomachinery rotor flows

A method is developed for predicting the behavior of three-dimensional, turbulent boundary layers occurring in internal flows, including those on turbomachinery rotor blades. These boundary layers are complex, turbulent, and subject to Coriolis and centrifugal forces. The major thrust of this paper is the development and use of an algebraic Reynolds stress model (ARSM) that captures the changes in turbulent flow structure arising from curvature, rotation, and three dimensionality. The prediction of pressure-driven secondary flow agrees well with the measured data, and all three turbulence models (k-epsilon, algebraic eddy viscosity, and ARSM) show the same level of agreement. The prediction of boundary-layer development on rotor blades shows much better agreement with measurements with the ARSM. It is essential to employ higher-order turbulence models to capture the effects of rotation, curvature, and three dimensionality on boundary layers in turbomachinery.

Zhang, J.↗
NASA NTRS2006

Optimal Control of Shock Wave Turbulent Boundary Layer Interactions Using Micro-Array Actuation

The intent of this study on micro-array flow control is to demonstrate the viability and economy of Response Surface Methodology (RSM) to determine optimal designs of micro-array actuation for controlling the shock wave turbulent boundary layer interactions within supersonic inlets and compare these concepts to conventional bleed performance. The term micro-array refers to micro-actuator arrays which have heights of 25 to 40 percent of the undisturbed supersonic boundary layer thickness. This study covers optimal control of shock wave turbulent boundary layer interactions using standard micro-vane, tapered micro-vane, and standard micro-ramp arrays at a free stream Mach number of 2.0. The effectiveness of the three micro-array devices was tested using a shock pressure rise induced by the 10 shock generator, which was sufficiently strong as to separate the turbulent supersonic boundary layer. The overall design purpose of the micro-arrays was to alter the properties of the supersonic boundary layer by introducing a cascade of counter-rotating micro-vortices in the near wall region. In this manner, the impact of the shock wave boundary layer (SWBL) interaction on the main flow field was minimized without boundary bleed.

Anderson, Bernhard H.↗
NASA NTRS1990

Effects of shock on the stability of hypersonic boundary layers

A set of linearized shock boundary conditions is derived, which is then imposed at the shock to account for the interaction of the shock wave with the boundary/shock layer instability wave; these boundary conditions are used to study the effect of shock on hypersonic boundary layer stability under the assumption of quasi-parallel flow. The result show that the shock has little effect on the boundary layer instability (subsonic first and second mode disturbances) when the shock is located outside the boundary layer edge. When the shock is located near the boundary layer edge, it exerts a stabilizing influence on the first and second modes. The shock also induces unstable supersonic modes with oscillatory structure in the shock layer, but these modes grow slower than the subsonic modes.

Chang, Chau-Lyan↗
NASA NTRS1985

Magnetic field properties of the distant magnetotail magnetopause and boundary layer

Models incorporating merging between dayside magnetosheath and magnetosphere field lines predict the location of the magnetotail boundary layer and bending of magnetotail field lines in the direction of the IMF. Previous observations supporting these models are reviewed, and a case of dense magnetotail boundary layer plasma and strongly bent field lines observed by ISEE 3 is examined. Observations of boundary layer plasma within a tangential discontinuity magnetopause are discussed. The model to explain this phenomenon requires that interconnected magnetotail and magnetosheath field lines leave the magnetotail via a narrow 'window'. Field lines in the dense boundary layer plasma veer away from the aberrated x axis more than those in the void magnetotail lobes in order to pass through the windows. Magnetosheath plasma must enter the magnetotail lobes through the windows at all downstream distances in order to supply he observed tailward flux of lobe plasma.

Sibeck, D. G.↗
NASA NTRS1972

On the calculation of three dimensional laminar boundary layer flows

An approximation which reduces the computation of three dimensional, laminar, compressible, boundary layer equations to the problem of solving two dimensional type boundary layer equations is presented. A comparison of this method with a fully three dimensional boundary layer calculation is provided.

Fillo, J. A.↗