Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Computer programs for calculating the static longitudinal aerodynamic characteristics of wing-body-tail configurations

Four computer programs developed to calculate the longitudinal aerodynamic characteristics of wing-body and wing-body-tail combinations are presented. The R1307 program is based on a linear method and is limited to the small range of angles of attack for which the lift and moment characteristics of wings and bodies are linear with angle of attack. The CRSFLW program is based on a crossflow method of predicting the forces and moments on bodies alone or wing-body combinations over a large angle of attack range. The SUBSON program predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at subsonic speeds and at angles of attack for which symmetrical pairs of vortices are shed from the body nose and the leading and side edges of the lifting surfaces. Program SUPSON predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at supersonic speeds in the same angle-of-attack range. A description of the use of each program, instructions for preparation of input, a description of the output, program listings, and sample cases for each program are included.

Mendenhall, M. R.↗
NASA NTRS1983

Hypersonic slender-wedge analysis with gradual change in angle of attack

The behavior of a narrow cross-section wedge wing moving at a high Mach number and subjected to an angle of attack changing exponentially with time is investigated. This type of wedge wing is commonly employed as a lifting surface in hypersonic vehicles. The time history of wall shear, heat transfer, displacement thickness, and viscous induced pressure are determined. Results show that for the same change in angle of attack, the flow attains the final steady state much faster when the change is exponential than when the change is made impulsively. In addition, the unsteady character of the flow is primarily confined to the initial stages of the change in the angle of attack.

Gupta, R. N.↗
NASA NTRS1960

An Experimental Investigation of Boundary-Layer Control for Drag Reduction of a Swept-Wing Section at Low Speed and High Reynolds Numbers

An investigation of laminar boundary-layer control by suction for purposes of drag reduction at low speed and high Reynolds numbers has been conducted in the Ames 12-Foot Pressure Wind Tunnel. The model was a 72.96-inch-chord wing panel, swept back 30 deg., which was installed between end plates to approximate a wing of infinite span. The airfoil section employed was a modified NACA 66-012 in the streamwise direction. Tests were limited to controlling the flow over only the upper surface of the model. Seventeen individually controllable suction chambers were provided below the surface to induce flow through 93 spanwise slots in the surface between the 0.0052- and 0.97-chord stations. Tests were made at angles of attack of 0 deg., +/- 1.0 deg., +/- 1.5 deg., and -2.0 deg. for Reynolds numbers from approximately 1.5 x 10(exp 6) to 4.0 x 10(exp 6) per foot. In general, essentially full-chord laminar flow was obtained for all conditions with small suction quantities. Minimum profile-drag coefficients of about 0.0005 to 0.0006 were obtained for the slotted surface at maximum values of the Reynolds number; these values include the Power required to induce suction as an equivalent drag.

Gault, Donald E.↗
NASA NTRS1977

Aerodynamic characteristics of a canard-controlled missile at Mach numbers of 1.5 and 2.0.

A typical missile model with nose mounted canards and cruciform tail surfaces was tested in the Ames 6- by 6-Foot Wind Tunnel to determine the contributions of the component aerodynamic surfaces to the static aerodynamic characteristics at Mach numbers of 1.5 and 2.0 and Reynolds number of 1 million based on body diameter. Data were obtained at angles of attack ranging from -3 deg to 12 deg for various stages of model build-up (i.e., with and without canard and/or tail surfaces). Results were obtained both with the model unrolled and rolled 45 deg. For the canard and tail arrangements investigated, the model was trimmable at angles of attack up to about 10 deg with canard deflections of 9 deg. Also, the tail arrangements studied provided ample pitch stability. there were no appreciable effects of model roll orientation.

Kassner, D. L.↗
NASA NTRS1981

Wing-alone aerodynamic characteristics for high angles of attack of supersonic speeds

An experiment was conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The wings tested varied in aspect ratio from 0.5 to 4.0 and in taper ratio from 0 to 1.0. The wings were tested at angles of attack ranging rom -5 deg to 60 deg and at Mach number from 1.60 to 4.60. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surfaces. Presented and discussed are results showing the effects of aspect ratio, taper ratio, Mach number, and angle of attack on force and moment coefficients and center of pressure locations. Also included are tabulations of the pressure measurements.

Stallings, R. L., Jr.↗
NASA NTRSDate not supplied

Computational Analysis of a Multiple-Nozzle Supersonic Retropropulsion Configuration

Supersonic retropropulsion is an enabling capability to land large payloads on the surface of Mars. The retropropulsion flowfield is a highly dynamic environment with strong shocks, free shear layers, and plumes opposing high-speed flow. For flight vehicles with large aerodynamic surface area, such as NASA concepts for human Mars exploration, retropropulsion can induce significant aerodynamic interference forces and moments on the vehicle during powered flight. A multiple-nozzle configuration from upcoming, inert gas, sub-scale, supersonic wind tunnel testing is simulated at Mach 2.4 conditions for angles of attack of 0 and 10 degrees and thrust coefficients of 0.5, 1.0, and 2.5. This paper examines changes in the resulting flowfield, surface pressures, and integrated forces with thrust force coefficient and angle of attack using a Detached Eddy Simulation approach.

retropropulsion↗
NASA NTRS1978

Comparison of aerodynamic data measured in air and Freon-12 wind-tunnel test mediums

An experimental investigation was carried out to measure two dimensional static aerodynamic characteristics of a 65 sub l-213 airfoil in air and Freon-12 (dichlorodifluoromethane) test mediums at corresponding test conditions. The purpose of the tests was to compare measurements in the two test mediums and to evaluate reported methods of converting Freon-12 data to equivalent air values. The test article was a two dimensional wing instrumented to measure chordwise surface pressure distributions. The parameters considered were Mach numbers from 0.6 to 1.0, angles of attack of zero deg and 1 deg, and Reynolds numbers based on model chord from 2,000,000 to 21,000,000. The agreement between data measured in the two test mediums is further improved by application of the transonic or area ratio similarity laws. Where flow conditions are characterized by surface shocks or stall, the effects of flow separation may not be identically reflected in the Freon-12 data, even when converted in accordance with existing similarity laws.

Weller, W. H.↗
NASA NTRS1960

Subsonic Flight Tests of a 1/7-Scale Radio-Controlled Model of the North American X-15 Airplane with Particular Reference to High Angel-of-Attack Conditions

An investigation of the subsonic stability and control characteristics of an unpowered 1/7-scale model based on the North American X-15 airplane was conducted by using a radio-controlled model launched from a helicopter and flown in free-gliding flight. At angles of attack below about 20 deg. where the model motions represent those of the X-15 airplane, the model was found to be both longitudinally and laterally stable, and the all-movable tail surfaces were found to be very effective. The model could also be flown at much higher angles of attack where the model motions did not necessarily represent those of the airplane because of slight geometrical differences and Reynolds number effects, but these test results are useful in evaluating the effectiveness at these angles of the type of lateral control system used in the X-15 airplane. In some cases, the model was flown to angles of attack as high as 60 or 70 deg. without encountering divergent or uncontrollable conditions. For some flights in which the model was subjected to rapid maneuvers, spinning motions were generated by application of corrective controls to oppose the direction of rotation. Rapid recoveries from this type of motion were achieved by applying roll control in the direction of rotation.

Hewes, Donald E.↗
NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗
NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗
NASA NTRS1960

An Experimental Investigation and Correlation of the Heat Reduction to Nonporous Surfaces Behind a Porous Leading Edge Through Which Coolant is Ejected

A configuration of a wing segment having constant chord thickness, 0 deg. sweep, a porous steel semicircular leading edge, and solid Inconel surfaces was tested in a Mach number 2.0 ethlyene-heated high-temperature air jet. Measurements were made of the wing surface temperatures at chordwise stations for several rates of helium flow through the porous leading edge. The investigation was conducted at stagnation temperatures ranging from 500 F to 2,400 F, at Reynolds numbers per foot ranging from 0.3 x 10(exp 7) to 1.2 x 10(exp 7), and at angles of attack of 0, +/- 5, and +/- 15 deg. The results indicated that the reduction of wing surface temperatures with respect to their values for no coolant flow, depended on the helium coolant flow rates and the distance behind the area of injection. The results were correlated in terms of the wall cooling parameter and the coolant flow-rate parameter, where the nondimensional flow rate was referenced to the cooled area up to the downstream position. For the same coolant flow rate, lower surface temperatures are achieved with a porous-wall cooling system. However, since flow-rate requirements decrease with increasing allowable surface temperatures, the higher allowable wall temperatures of the solid wall as compared to the structurally weaker porous wall- sharply reduce the flow-rate requirements of a downstream cooling system. Thus, for certain flight conditions it is possible to compensate for the lower efficiency of the downstream or solid-wall cooling system. For example, a downstream cooling system using solid walls that must be maintained at 1,800 F would require less coolant for Mach numbers up to 5.5 than would a porous-wall cooling system for which the walls must be maintained at temperatures less than or equal to 9000 F.

Witte, William G.↗
NASA NTRS1983

Heating analysis of bent-nose biconics at high angles of attack using the parabolized Navier-Stokes equations

A method based on the Parabolized Navier-Stokes equations is used to calculate the flow field and heat transfer of lifting entry vehicles. The method is based on the Bean and Warming implicit algorithm and uses a new procedure for preventing departure solutions. Calculations are carried out for blunt on-axis and bent biconics, assuming a perfect gas and laminar flow, and compared with available heat transfer, surface pressure and shock shape measurements for a range of Mach numbers and angles of attack. In all calculations presented here, the starting solution is obtained from available inviscid and boundary layer codes. Good agreement with experiment is indicated. Thus, the method provides an accurate and rather inexpensive procedure for calculating three-dimensional flows at supersonic Mach numbers.

Stephenson, B. L.↗
NASA NTRS2009

Deployable Aeroshell Flexible Thermal Protection System Testing

Deployable aeroshells offer the promise of achieving larger aeroshell surface areas for entry vehicles than otherwise attainable without deployment. With the larger surface area comes the ability to decelerate high-mass entry vehicles at relatively low ballistic coefficients. However, for an aeroshell to perform even at the low ballistic coefficients attainable with deployable aeroshells, a flexible thermal protection system (TPS) is required that is capable of surviving reasonably high heat flux and durable enough to survive the rigors of construction handling, high density packing, deployment, aerodynamic loading and aerothermal heating. The Program for the Advancement of Inflatable Decelerators for Atmospheric Entry (PAIDAE) is tasked with developing the technologies required to increase the technology readiness level (TRL) of inflatable deployable aeroshells, and one of several of the technologies PAIDAE is developing for use on inflatable aeroshells is flexible TPS. Several flexible TPS layups were designed, based on commercially available materials, and tested in NASA Langley Research Center's 8 Foot High Temperature Tunnel (8ft HTT). The TPS layups were designed for, and tested at three different conditions that are representative of conditions seen in entry simulation analyses of inflatable aeroshell concepts. Two conditions were produced in a single run with a sting-mounted dual wedge test fixture. The dual wedge test fixture had one row of sample mounting locations (forward) at about half the running length of the top surface of the wedge. At about two thirds of the running length of the wedge, a second test surface drafted up at five degrees relative to the first test surface established the remaining running length of the wedge test fixture. A second row of sample mounting locations (aft) was positioned in the middle of the running length of the second test surface. Once the desired flow conditions were established in the test section the dual wedge test fixture, oriented at 5 degrees angle of attack down, was injected into the flow. In this configuration the aft sample mounting location was subjected to roughly twice the heat flux and surface pressure of the forward mounting location. The tunnel was run at two different conditions for the test series: 1) 'Low Pressure', and 2) 'High Pressure'. At 'Low Pressure' conditions the TPS layups were tested at 6W/cm2 and 11W/cm2 while at 'High Pressure' conditions the TPS layups were tested at 11W/cm2 and 20W/cm2. This paper details the test configuration of the TPS samples in the 8Ft HTT, the sample holder assembly, TPS sample layup construction, sample instrumentation, results from this testing, as well as lessons learned.

Hughes, Stephen J.↗
NASA NTRS1979

Laminar and turbulent flows over spherically blunted cone and hyperboloid with massive surface blowing

Numerical solutions are presented for the flow over a spherically blunted cone and hyperboloid with massive surface blowing. Time-dependent viscous shock-layer equations are used to describe the flow field. The boundary conditions on the body surface include a prescribed blowing-rate distribution. The governing equations are solved by a time-asymptotic finite-difference method. Results presented here are only for a perfect gas-type flow at zero angle of attack. Both laminar and turbulent flow solutions are obtained. It is found that the effect of the surface blowing on the laminar flow field is to smooth out the curvature discontinuity at the sphere-cone juncture point, which results in a positive pressure gradient over the body. The shock slope increases on the downstream portion of the body as the surface blowing rate is increased. The turbulent flow with surface blowing is found to redevelop a boundary-layer-like region near the surface. The effects of this boundary-layer region on the flow field and heating rates are discussed.

Kumar, A.↗
NASA NTRS1984

Leading edge flap system for aircraft control augmentation

Traditional roll control systems such as ailerons, elevons or spoilers are least effective at high angles of attack due to boundary layer separation over the wing. This invention uses independently deployed leading edge flaps on the upper surfaces of vortex stabilized wings to shift the center of lift outboard. A rolling moment is created that is used to control roll in flight at high angles of attack. The effectiveness of the rolling moment increases linearly with angle of attack. No adverse yaw effects are induced. In an alternate mode of operation, both leading edge flaps are deployed together at cruise speeds to create a very effective airbrake without appreciable modification in pitching moment. Little trim change is required.

Rao, D. M.↗
NASA NTRS1959

An Investigation of the Pitching-Moment Contribution of a High Horizontal Tail on an Unswept-Wing and Body Combination at Mach Numbers from 0.80 to 1.40

An investigation has been conducted to determine the effects of a high positioned horizontal tail on a wing-body configuration having a thin unswept wing of aspect ratio 3.09. Lift and pitching-moment coefficients were obtained for Mach numbers from 0.80 to 1.40 at Reynolds numbers of 1.0 and 1.5 million and for angles of attack to 20 deg. An experimental study of the pitching-moment contribution of the horizontal tail indicated that the marked destabilizing effect of the horizontal tail at high angles of attack for Mach numbers of 0.80 to 1.00 was associated with the formation of completely separated flow on the upper surface of the wing. Computations of the interference effects of the wing-body combination on the tail for Mach numbers of 0.80 and 0.94 and high angles of attack confirmed this conclusion. For a Mach number of 1.40, and high angles of attack, computations disclosed that the destabilizing effect primarily resulted from the trailing vortices of the wing. Two modifications to the basic wing plan form, which consisted of chord extensions, were generally unsuccessful in reducing the destabilizing contributions of the horizontal tail at high angles of attack.

Lippmann, Garth W.↗
NASA NTRS1999

Reactivity of CF(n) (n = 1-3) Radicals with a Silica Surface

The trends in reactivity of CF(n) radicals with SiO2 and the site selectivity of the attack are studied using two different cluster models. The reaction barriers for the most energetically favorable reaction are computed. It is shown that CF(n) radicals are fairly unreactive towards SiO2.

Ricca, Alessandra↗
NASA NTRS1976

An experimental and computational investigation of the flow field about a transonic airfoil in supercritical flow with turbulent boundary-layer separation

A combined experimental and computational research program is described for testing and guiding turbulence modeling within regions of separation induced by shock waves incident in turbulent boundary layers. Specifically, studies are made of the separated flow the rear portion of an 18%-thick circular-arc airfoil at zero angle of attack in high Reynolds number supercritical flow. The measurements include distributions of surface static pressure and local skin friction. The instruments employed include highfrequency response pressure cells and a large array of surface hot-wire skin-friction gages. Computations at the experimental flow conditions are made using time-dependent solutions of ensemble-averaged Navier-Stokes equations, plus additional equations for the turbulence modeling.

Rubesin, M. W.↗