Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Wind tunnel investigation of an oblique wing transport model at mach numbers between 0.6 and 1.4

Models of three practical oblique-wing transport configurations were tested in the NASA Ames 11 foot wind tunnel. The three configurations used a common forward fuselage, wing, and support system but employed different aft fuselage sections simulating alternate propulsion system installations. These included an integrated propulsion system, pylon-mounted nacelles, and clean (no propulsion system) configuration. The tests were conducted over a Mach number range from 0.6 to 1.4 and at sweep angles from 0 to 60 degrees. The nominal unit Reynolds number was 1.83 million per meter and the angle of attack range was -3 to +6 degrees. The models were mounted in the tunnel by means of a lower blade support system. The interference effects of this lower blade and the flow inclination were determined by using an image blade system and testing the configuration in both the upright and inverted positions.

Black, R. L.↗
NASA NTRS1953

A low-speed experimental study of the directional characteristics of a sharp-nosed fuselage through a large angle-of-attack range at zero angle of sideslip

Static yawing moments and some instantaneous yawing moments are presented through a range of angle of attack at zero sideslip angle for a plain fuselage model having a sharp conical nose and for the fuselage with several nose modifications, one of which consisted of a ring located at different stations along the nose. Some circumferential pressure measurements at one station on the body at several angles of attack are also presented.

PROTUBERANCES-BODIES↗
NASA NTRS1998

Monte Carlo Computational Modeling of the Energy Dependence of Atomic Oxygen Undercutting of Protected Polymers

A Monte Carlo computational model has been developed which simulates atomic oxygen attack of protected polymers at defect sites in the protective coatings. The parameters defining how atomic oxygen interacts with polymers and protective coatings as well as the scattering processes which occur have been optimized to replicate experimental results observed from protected polyimide Kapton on the Long Duration Exposure Facility (LDEF) mission. Computational prediction of atomic oxygen undercutting at defect sites in protective coatings for various arrival energies was investigated. The atomic oxygen undercutting energy dependence predictions enable one to predict mass loss that would occur in low Earth orbit, based on lower energy ground laboratory atomic oxygen beam systems. Results of computational model prediction of undercut cavity size as a function of energy and defect size will be presented to provide insight into expected in-space mass loss of protected polymers with protective coating defects based on lower energy ground laboratory testing.

Banks, Bruce A.↗
NASA NTRS1972

Asymmetric lateral-directional characteristics of pointed bodies of revolution at high angles of attack

A low-speed wind-tunnel investigation was conducted in order to determine the cause of asymmetric yawing moments produced by long pointed fuselage nose shapes at high angles of attack. Force tests were conducted with a cone, tangent-ogive model, and a paraboloid of revolution over a range of Reynolds numbers from 0.15 million to 0.35 million for an angle-of-attack range from 0 deg to 75 deg and an angle-of-sideslip range of plus or minus 30 deg. Tuft and smoke flow-visualization tests were also conducted to aid in the analysis. Large asymmetric yawing moments were obtained for the cone and tangent-ogive body at high angles of attack (of the order of 40 to 60 deg). These large moments were caused by asymmetric shedding of vortex sheets off the long pointed nose. The asymmetric moments could be eliminated by use of symmetrically arranged strikes on the nose. The paraboloid of revolution did not produce a strong asymmetric flow field at high angles of attack and did not exhibit asymmetric moments.

Coe, P. L., Jr.↗
NASA NTRS1957

Experimental static aerodynamic forces and moments at high subsonic speeds on a missile model during simulated launching from the midsemispan location of a 45 degree sweptback wing-fuselage-pylon combination

An investigation was made at high subsonic speeds in the Langley high-speed 7- by 10-foot tunnel to determine the static aerodynamic forces and moments on a missile model during simulated launching from the midsemispan location of a 45 degree sweptback wing-fuselage-pylon combination. The results indicated significant variations in all the aerodynamic components with changes in chordwise location of the missile. Increasing the angle of attack caused increases in the induced effects on the missile model because of the wing-fuselage-pylon combination. Increasing the Mach number had little effect on the variations of the missile aerodynamic characteristics with angle of attack except that nonlinearities were incurred at smaller angles of attack for the higher Mach numbers. The effects of finite wing thickness on the missile characteristics, at zero angle of attack, increase with increasing Mach number. The effects of the pylon on the missile characteristics were to causeincreases in the rolling-moment variation with angle of attack and a negative displacement of the pitching-moment curves at zero angle of attack. The effects of skewing the missile in the lateral direction relative to and sideslipping the missile with the wing-fuselage-pylon combination were to cause additional increments in side force at zero angle of attack. For the missile yawing moments the effects of changes in skew or sideslip angles were qualitatively as would be expected from consideration of the isolated missile characteristics, although there existed differences in theyawing-moment magnitudes.

Alford, William J↗
NASA NTRS1980

Flow Visualization Study of the F-14 Fighter Aircraft Configuration

Water tunnel studies were performed to qualitatively define the flow field of the F-14. Particular emphasis was placed on defining the vortex flows generated at high angles of attack. The flow visualization tests were conducted in the Northrop water tunnel using a 1/72 scale model of the F-14 with a wing leading-edge sweep of 20 deg. Flow visualization photographs were obtained for angles of attack up to 55 deg and sideslip angles up to 10 deg. The F-14 model was investigated to determine the vortex flow field development, vortex path, and vortex breakdown characteristics as a function of angle of attack and sideslip. Vortex flows were found to develop on the highly swept glove and on the upper surface of the forebody. At 10 deg of sideslip, the windward glove vortex shifted inboard and broke down farther forward than the leeward glove vortex. This asymmetric breakdown of the vortices in sideslip contributes to a reduction in the lateral stability above 20 deg angle of attack. The initial loss of directional stability is a consequence of the adverse sidewash from the windward vortex and the reduced dynamic pressure at the vertical tails.

Lorincz, D. J.↗
NASA NTRS1981

Force and moment, flow-visualization, and boundary-layer tests on a shuttle orbiter model at Mach 6

Force and moment, flow visualization, and boundary layer state tests were conducted using two 0.004 scale shuttle orbiter models. The force and moment tests were conducted for an angle of attack range from 20 to 40 deg and for Reynolds numbers based on reference length from 0.4 million to 3.6 million. Schlieren photographs were obtained for each angle of attack and Reynolds number. The boundary layer state tests, which were conducted using hot film sensors mounted in a separate model, were conducted over the same range of conditions as the force tests. Test results were combined to show that changes in the boundary layer on a typical hypersonic force test model affect measurement of the axial force coefficient and that the state of the local boundary layer is important for interpreting hypersonic aerodynamic test results.

Calloway, R. L.↗
NASA NTRS1985

Identification of integro-differential systems for application to unsteady aerodynamics and aeroelasticity

Integrodifferential equations for unsteady aerodynamic and aeroelastic phenomena are identified by means of several approaches. When the product of the frequency of motion and maximum time delay is much smaller than unity, the integral term can be approximated by a constant; when greater than unity, however, approximation of the integral is not possible. Approximations of integrodifferential models are needed to obtain identifiability. While the least-squares method may be used for model determination, the maximum likelihood technique is needed for accurate parameter estimation. High angle of attack and post stall/spin regions appear to have characteristics that can be satisfied by indicial models.

Gupta, N. K.↗
NASA NTRS1997

Full-Potential Modeling of Blade-Vortex Interactions

A study of the full-potential modeling of a blade-vortex interaction was made. A primary goal of this study was to investigate the effectiveness of the various methods of modeling the vortex. The model problem restricts the interaction to that of an infinite wing with an infinite line vortex moving parallel to its leading edge. This problem provides a convenient testing ground for the various methods of modeling the vortex while retaining the essential physics of the full three-dimensional interaction. A full-potential algorithm specifically tailored to solve the blade-vortex interaction (BVI) was developed to solve this problem. The basic algorithm was modified to include the effect of a vortex passing near the airfoil. Four different methods of modeling the vortex were used: (1) the angle-of-attack method, (2) the lifting-surface method, (3) the branch-cut method, and (4) the split-potential method. A side-by-side comparison of the four models was conducted. These comparisons included comparing generated velocity fields, a subcritical interaction, and a critical interaction. The subcritical and critical interactions are compared with experimentally generated results. The split-potential model was used to make a survey of some of the more critical parameters which affect the BVI.

Jones, Henry E.↗
NASA NTRS2000

Subsonic and Transonic Dynamic Stability Characteristics of the X-33

Dynamic stability testing was conducted on a 2.5% scale model of the X-33 technology demonstrator sub-orbital flight-test vehicle. This testing was conducted at the NASA Langley Research Center (LaRC) l6-Foot Transonic Wind Tunnel with the LaRC High-speed Dynamic Stability system. Forced oscillation data were acquired for various configurations over a Mach number range of 0.3 to 1.15 measuring pitch, roll and yaw damping, as well as the normal force due to pitch rate and the cross derivatives. The test angle of attack range was from -2 to 24 degrees, except for those cases where load constraints limited the higher angles of attack at the higher Mach numbers. A variety of model configurations with and without control surfaces were employed, including a body alone configuration. Stable pitch damping is exhibited for the baseline configuration throughout the angle of attack range for Mach numbers 0.3, 0.8, and 1.15. Stable pitch damping is present for Mach numbers 0.9 and 0.6 with the exception of angles 2 and 16 degrees, respectively. Constant and stable roll damping were present for the baseline configuration over the range of Mach numbers up to an angle of attack of 16 degrees. The yaw damping for the baseline is somewhat stable and constant for the angle of attack range from -2 to 8 degrees, with the exception of Mach numbers 0.6 and 0.8. Yaw damping becomes highly unstable for all Mach numbers at angles of attack greater than 8 degrees.

Tomek, D.↗
NASA NTRS1992

Failure detection and fault management techniques for flush airdata sensing systems

Methods based on chi-squared analysis are presented for detecting system and individual-port failures in the high-angle-of-attack flush airdata sensing system on the NASA F-18 High Alpha Research Vehicle. The HI-FADS hardware is introduced, and the aerodynamic model describes measured pressure in terms of dynamic pressure, angle of attack, angle of sideslip, and static pressure. Chi-squared analysis is described in the presentation of the concept for failure detection and fault management which includes nominal, iteration, and fault-management modes. A matrix of pressure orifices arranged in concentric circles on the nose of the aircraft indicate the parameters which are applied to the regression algorithms. The sensing techniques are applied to the F-18 flight data, and two examples are given of the computed angle-of-attack time histories. The failure-detection and fault-management techniques permit the matrix to be multiply redundant, and the chi-squared analysis is shown to be useful in the detection of failures.

Whitmore, Stephen A.↗
NASA NTRS1972

Space shuttle: Stability and control effectiveness at high and low angles of attack and effects of variations in engine shround, fin, and drag petal configurations for the Boeing 0.008899-scale pressure-fed ballistic recoverable booster, model 979-160

Experimental aerodynamic investigations were carried out in the Boeing transonic and supersonic wind tunnels on a 0.008899-scale model of a proposed pressure-fed ballistic recoverable booster (BRB) configuration. The purpose of the test program was to determine the stability and control effectiveness of the basic configuration at high and low angles of attack, and to conduct parametric studies of various engine shroud, fin, and drag petal configurations. Six-component force data and base pressure data were obtained over a Mach number range of 0.35 to 4.0 at angles of attack of -5 to 25 and 55 to 85 at zero degrees sideslip and over a sideslip range of -10 to +10 at angles of attack ranging from -10 to 72.5. Two-component force data were also obtained with a fin balance on selected runs.

Hanson, R. L.↗
NASA NTRS1996

Comparison of Turbulence Models for Nozzle-Afterbody Flows with Propulsive Jets

A numerical investigation was conducted to assess the accuracy of two turbulence models when computing non-axisymmetric nozzle-afterbody flows with propulsive jets. Navier-Stokes solutions were obtained for a Convergent-divergent non-axisymmetric nozzle-afterbody and its associated jet exhaust plume at free-stream Mach numbers of 0.600 and 0.938 at an angle of attack of 0 deg. The Reynolds number based on model length was approximately 20 x 10(exp 6). Turbulent dissipation was modeled by the algebraic Baldwin-Lomax turbulence model with the Degani-Schiff modification and by the standard Jones-Launder kappa-epsilon turbulence model. At flow conditions without strong shocks and with little or no separation, both turbulence models predicted the pressures on the surfaces of the nozzle very well. When strong shocks and massive separation existed, both turbulence models were unable to predict the flow accurately. Mixing of the jet exhaust plume and the external flow was underpredicted. The differences in drag coefficients for the two turbulence models illustrate that substantial development is still required for computing very complex flows before nozzle performance can be predicted accurately for all external flow conditions.

Compton, William B., III↗
NASA NTRS1958

Elliptic Cones Alone and with Wings at Supersonic Speed

To help fill the gap in the knowledge of aerodynamics of shapes intermediate between bodies of revolution and flat triangular wings, force and moment characteristics for elliptic cones have been experimentally determined for Mach numbers of 1.97 and 2.94. Elliptic cones having cross-sectional axis ratios from 1 through 6 and with lengths and base areas equal to circular cones of fineness ratios 3.67 and 5 have been studied for angles of bank of 0 degree and 90 degrees. Elliptic and circular cones in combination with triangular wings of aspect ratios 1 and 1.5 also have been considered. The angle-of-attack range was from 0 degree to about 16 degrees, and the Reynolds number was 8 x 10(6), based on model length. In addition to the forces and moments at angle of attack, pressure distributions for elliptic cones at zero angle of attack have been determined. The results of this investigation indicate that there are distinct aerodynamic advantages to the use of elliptic cones.

Jorgensen, Leland H↗
NASA NTRS1976

Wind-tunnel testing with a rotary-balance apparatus to simulate aircraft spin motions

Experiments have been conducted in the Ames 12-Foot Pressure Wind Tunnel on a simple airplane-like model using a rotary-balance apparatus to simulate a steady spin motion at high angles of attack. Tests were run at Mach numbers of 0.1 and 0.25 over a wide Reynolds number range with the angle of attack varying from 45 to 90 deg. During previous tests of the same research model, some difficulties were experienced with measurement accuracy in the low-to-medium range of Reynolds number because of limitations in the sensitivity of selected force balances. For the present tests, special balances were built to provide accurate measurements of the nose and tail contributions to spin motions and improvements were made to the overall test apparatus. The results of this test, including some interesting hysteresis effects with spin rate, are described. Some of the problems associated with rotary-balance tests at high Reynolds numbers are discussed. A new large-scale rotary apparatus now nearing completion for use in the Ames 12-Foot and 11- by 11-Foot Wind Tunnels is described briefly.

Malcolm, G. N.↗
NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack V : spoilers and ailerons on rectangular wings

This report covers the fifth of a series of systematic investigations in which lateral control devices are compared with particular reference to their effectiveness at high angles of attack. The present report deals with tests of spoilers and ordinary ailerons on rectangular Clark y wing models. In an effort to obtain satisfactory control throughout the entire angle-of-attack range that can be maintained in flight, various spoilers were tested in combination with two sizes of previously tested ordinary ailerons - one of average proportions and the other short and wide. In addition, one large spoiler was tested alone. It was found that when ailerons and spoilers are used together the full effect of both is not obtained if the spoilers are located directly in front of the ailerons. With the proper combination of spoiler and aileron, however, it is possible to obtain satisfactory rolling control up to high angles of attack (15 degrees to 20 degrees), together with favorable yawing moments and small control forces. A moderate amount of rolling control with favorable yawing moments and small control forces was obtained with the large spoiler alone.

Weick, Fred E↗
NASA NTRS1956

Some Effects of Roll Rate on the Longitudinal Stability Characteristics of a Cruciform Missile Configuration as Determined from Flight Test for a Mach Number Range of 1.1. to 1.8

A model of a cruciform missile configuration having a low-aspect-ratio wing equipped with flap-type controls was flight tested in order to determine stability and control characteristics while rolling at about 5 radians per second. Comparison is made with results from a similar model which rolled at a much lower rate. Results showed that, if the ratio of roll rate to natural circular frequency in pitch is not greater than about 0.3, the motion following a step disturbance in pitch essentially remains in a plane in space. The slope of normal- force coefficient against angle of attack C(sub N(sub alpha)) was the same as for the slowly rolling model at 0 degrees control deflection but C(sub N(sub alpha)) was much higher for the faster rolling model at about 5 degrees control deflection. The slope of pitching-moment coefficient against angle of attack C(sub m(sub alpha)) as determined from the model period of oscillation was the same for both models at 0 degrees control deflection but was lower for the faster rolling model at about 5 degrees control deflection. Damping data for the faster rolling model showed considerably more scatter than for the slowly rolling model.

Lundstrom, Reginald R↗
NASA NTRS1976

Effects of Mach number and afterbody length on aerodynamic side forces at zero sideslip on symmetric bodies at high angles of attack

Wind-tunnel measurements of side force over the Mach number range of 0.25 to 2 for pointed forebody-alone and for ogive-cylinder models of various fineness ratios up to 16, are presented. The angle of attack where side force first occurs (onset), where it returns to zero (upper limit), and its magnitude are examined. The onset angle depends only on body geometry, longer bodies having lower onset angles. The upper limit, which is about 80 deg at M = 0.25, decreases with Mach number. The maximum side forces decrease with increasing Mach number, approaching zero within the Mach number range of 0.8 to 1.2; within this range, the Mach number at which the forces approach zero varies directly with forebody slenderness.

Keener, E. R.↗