Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alloy development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at.%Cu alloy

Microstructure formation of a hypo-eutectic Al-11Cu (atom percent) alloy during solidification after laser melting has been studied by transmission electron microscopy (TEM). The evolution of the solid-liquid-interface velocity, V SL , during the solidification process has been determined from direct observation by in-situ TEM. This enabled correlating V SL with development of four distinct microstructure zones. Crystal growth mode transitions from planar to cellular, cellular to dendritic, dendritic to cellular, and cellular to planar, have been observed for the accelerating solid-liquid-interface. The transition from coupled two-phase growth to the single-phase growth occurred for V SL = V a = (0.80±0.05) m/s, where V a is the velocity of absolute stability, at the onset of banded morphology grain formation. The in-situ and post-mortem TEM uniquely permitted determination of the non-equilibrium solidus for the rapidly solidifying Al-11Cu alloy. Experimental evidence for solute clustering and chemical ordering tendencies at length scales on the order of ≤ 5nm has been detected in the single-phase regions of the banded grains. The structural features of the single-phase bands have been interpreted as signatures of ‘frozen in’ configurations present in the liquid boundary layer adjacent to the growing crystal, which has a width of about 3nm. Finally, the nano-scale spatiotemporal resolution experimental TEM studies performed here provided quantitative metrics, e.g. the solidification interface velocity dependent solute concentration of the α-Al phase and the near-atomic scale structure in the single-phase bands, that are uniquely suitable for comparison with theory and model predictions for solidification microstructure development in multicomponent alloys after laser melting.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Improved Models of Long-Term Creep Behavior of High Performance Structural Alloys

In this program, QuesTek Innovations LLC, a leader in the field of computational materials design, proposes to develop a robust creep-modeling toolkit that expands its computational Materials by Design® technology, in order to predict the long-term creep performance of materials for base alloys and weldments in fossil energy systems under wide thermal and mechanical conditions. The Material Database Group of NIMS (National Institute for Material Science, JAPAN) provides reliable public data for long-term creep behavior over 300,000 hours (> 34 years) for a variety of materials including high Cr steels along with seminal work performed by EPRI (Electric Power Research Institute) on creep failure of these steels. QuesTek would rely on these premier institutions for experimental data needed to calibrate models. The developed tool has wider applications than the state-of-the-art modeling tools. It includes the effects of chemistry variations, microstructure variation (weldments) etc .which is lacking in many available models requiring the model to be calibrated to large number of datasets for accurate predictions. A model based on fundamental mechanism has promises in application to different materials, other than the demonstrated material (Grade 91 steels) in the current program. As a result of such an effort, we envision greatly advancing the state-of-the-art modeling tools for creep life assessments of different materials.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Achieving strong and stable nanocrystalline Al alloys through compositional design

Abstract Al alloys often suffer from low mechanical strength and lack high-temperature microstructural and mechanical robustness. A series of binary and ternary nanocrystalline (NC) Al transition metal alloys with supersaturated solid solution and columnar nanograins have been recently developed by using magnetron sputtering, manifesting a new realm of mechanical properties and thermal stability. Distinct solutes cause evident differences in the phase transformations and efficiencies for grain refinement and crystalline-to-amorphous transition. Certain sputtered Al-TM alloys have shown room-temperature mechanical strengths greater than 2 GPa and outstanding thermal stability up to 400 °C. In addition, the NC Al alloys show mechanical anisotropy and tension–compression asymmetry, revealed by micromechanical tests. Through the process encapsulating various compositionally distinct systems, we attempt to illuminate the solute effects on grain refinement and properties and more importantly, tentatively unravel the design criteria for high-strength and yet thermally stable NC Al alloys. Graphic Abstract

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid data acquisition and machine learning-assisted composition design of functionally graded alloys via wire arc additive manufacturing

Abstract The lack of high-quality datasets in materials science hinders artificial intelligence (AI)-driven alloy design. To address this challenge, wire arc additive manufacturing (WAAM) was employed to fabricate graded alloys, generating extensive data for machine learning (ML)-assisted property prediction. ML models were developed using high-throughput experiments, computational models, and genetic algorithm to optimize feature selection, successfully predicting hardness and porosity. The ML model demonstrated its efficacy by designing a gradient alloy with enhanced properties. However, scaling up revealed uncertainties in tensile property and porosity due to differences in size and thermal conditions between the designed alloy build and the gradient print used to construct the ML model. This underscores the need for uncertainty quantification and process optimization in WAAM-driven alloy design. Our work advances AI-integrated additive manufacturing, offering a rapid approach to exploring process–structure–property relationships and accelerating materials development.

Wang, Xin↗
DOE OSTI2024

A Critical Review on the History of Fabricating Monolithic U-Mo Fuel Plates

Fabrication of uranium-molybdenum alloy fuels has been occurring since the early 2000s in support of the development of a high-uranium-density low-enrichment fuel for use in high-performance research and test reactors which operate at relatively low temperatures. The primary fuel form—a thin foil of uranium, alloyed with 10wt% molybdenum, which is coated in a layer of zirconium and then encapsulated with aluminum 6061 as a cladding material—was developed over a number of years.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Crystallographic texture formation in Fe-9wt%Si alloy during deformation and phase transition at high pressure

SUMMARY The seismic anisotropy of the Earth's solid inner core has been the topic of much research. It could be explained by the crystallographic preferred orientation (CPO) developing during convection. The likely phase is hexagonal close-packed iron (hcp), alloyed with nickel and some lighter elements. Here we use high energy synchrotron X-rays to study CPO in Fe-9wt%Si, uniaxially compressed in a diamond anvil cell in radial geometry. The experiments reveal that strong preferred orientation forms in the low-pressure body-centred cubic (bcc) phase that appears to be softer than pure iron. CPO is attributed to dominant {110}<111> slip. The onset of the bcc→hcp transition occurs at a pressure of ≈15 GPa, and the alloy remains in a two phase bcc + hcp state up to 40 GPa. The hcp phase forms first with a distinct {11$\bar{2}$0} maximum perpendicular to compression. Modelling shows that this is a transformation texture, which can be described by Burgers orientation relationship with variant selection. Experimental results suggest that bcc grains oriented with <100> parallel to compression transform into hcp first. The CPO of the hcp changes only slowly during further pressure and deviatoric stress increase at ambient temperature. After heating to 1600 K, a change in the hcp CPO is observed with alignment of (0001) planes perpendicular to compression that can be interpreted as dominant (0001)<11$\bar{2}$0> slip, combined with {10$\bar{1}$2}<$\bar{1}$011> mechanical twinning, which is similar to the deformation modes suggested previously for pure hcp iron at inner core conditions.

Vasin, Roman N.↗
DOE OSTI2022

Improving Structural Integrity of Direct Laser-Deposited Ni – Co – Cr – Al – Y Superalloys by Alloy Modification

Abstract Ni- and Co-based M–Cr–Al–Y (M = Ni and/or Co), dual phase β and γ/γ′, β—Ni–Al, γ—Ni(Co, Cr), and γ′—Ni3–Al superalloys exhibit several beneficial high-temperature (>1000 °C) (2012 °F) strength and corrosion resistance properties. Our study investigates the feasibility of fabricating a commercially available Ni–Co–Cr–AlY alloy (tradename “Amdry 386”) using laser directed energy deposition (laser-DED). A significant challenge for laser fabrication of bulk Amdry 386 (A386) structures stems from the presence of relatively higher amounts of the β phase than γ/γ′ phases. While prior studies report laser fabrication of these materials in coating and cladding configurations, bulk structures have not been realized. To investigate these challenges, this study was developed to systematically evaluate the effects of modifying the A386 alloy by adding 10, 20, and 30% by weight of a Ni–20%Cr (Ni–Cr) alloy (mainly γ/γ′). Laser-DED-fabricated A386 coupons exhibited a metastable, rapidly solidified β-rich microstructure typical to laser processes. The A386 + Ni–Cr mixtures were processed using laser-DED, and small coupons from each composition were evaluated using SEM, XRD, and microhardness to characterize the as-processed microstructure. Thermodynamic modeling was performed to determine the phase evolution as a function of the alloy composition. The dominating phase switches from β to γ/γ’ between the A386 and A386 + 10% Ni–Cr mixtures, but the increase in structural integrity is not observed until the Ni–Cr additions reach a minimum of 20%. Our results show that the alloy chemistry can be successfully modified to improve the structural integrity of laser-processed structures.

Engineering↗
DOE OSTI2023

Design, Fabrication, and Screening of Environmental‐Thermal Barrier Coatings Prepared by Ultrafast High‐Temperature Sintering

Abstract The demand for more efficient gas turbines relies heavily on the development of new environmental‐thermal barrier coatings (ETBCs). However, there is still uncertainty about which alloys and composites will be used for the next generation of turbine blades, as well as the most promising coating materials. Herein, an ETBCs development strategy is presented by integrating the coating design, synthesis, and screening using an ultrafast high temperature sintering (UHS) technique to accelerate coating improvements. The initial basis for composition selection is their thermal expansion mismatch with the substrate alloys; for which a temperature‐dependent coefficient of thermal expansion database is created. By combining tape casting method with the UHS technique a high‐throughput synthesis of single and multi‐layer coatings are realized with different compositions, layer stacking sequences, and layer thicknesses. To evaluate the coatings, thermal cycling tests from room temperature to 1300 °C are conducted. The approach enabled coatings on objects with complex geometries, multi‐layer ETBCs, and porosity tailoring by using staged UHS that runs with different temperatures and durations. The fast iteration strategy is more cost‐effective for the screening of ETBCs compared to conventional methods and greater throughput which can be further extended for rapid optimization of other materials systems.

Xie, Hua↗
DOE OSTI2022

Quarterly Management Document – FY22, 3rd Quarter, Multi-pass Hybrid Laser Arc Welding of Alloy 740H

During the 3rd quarter of FY22, progress was made on modeling and simulation of deep penetration laser welding of Alloy 740H. Advances in the modeling of residual stress development arising from the calculated temperature field of the solidifying weld pool were made to understand the development of solidification cracking. Additionally, preliminary modeling of the temperature field within the weld pool of a wobbling laser heat source was performed. The maximum temperature of the weld pool was found to vary with time. These result will allow modeling of deep penetration laser welding using a wobbling laser to mitigate weld defects and cracking. Also, additional characterization of hybrid laser arc welds indicated that these welds were not defect-free as originally thought and the current HLA welds would not be acceptable under criteria outlined in the ASME Boiler and Pressure Vessel Code, Section IX. Therefore, additional welding trails with variation of the welding parameters and HLA welding configurations are required to produce welds acceptable under the Section IX criteria. It was shown that considerable reduction of HLAW defects had been achieved with each successive welding campaign. Therefore additional variation of HLAW parameters may still yield the desired defect-free welds, however, options for alternate HLAW configurations as well as plate preheating are outlined as contingency plans to obtain suitable welds. These additional (unplanned) HLAW trial may prevent subsequent milestones from being achieved within the original budget.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Imaging transient solidification behavior

Solidification processing offers the first opportunity to control microstructure, properties, and performance in metallic alloy components. Until recently, microstructural evaluations were limited to post-solidification characterization by destructive methods. We review the development of time-resolved, in situimaging techniques capable of capturing solid-liquid interfacial evolution in metallic alloys with high spatial and temporal resolution underdiverse solidification conditions relevant for applications ranging from conventional directional solidification, crystal growth, and casting,to welding and additive manufacturing. These experiments enable direct visualization of transient behaviors that would otherwise remain unknown, uniquely providinginsights into the physics that impact microstructure and defect development and strategies for microstructuralcontrol and defect mitigation. Understanding microstructural evolution and the characteristics that form under various solidification conditions is essential for the development of multiscale, experimentallyinformed predictive modeling. This is highlightedby solidification simulations that utilize in situmeasurements of solidification dynamics from state-of-the-art experimental techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Comparative Analysis of Austenitized Steel Microstructures Due to Induction and Conventional Heating in High Magnetic Field

While magnetic field-assisted processing shows promise in improving alloys’ mechanical properties, insufficient descriptions of heating methods hinder development of tailored processing pathways. This study investigates how induction and conventional heating affect microstructures of near-eutectoid Fe–C steel with and without 9 T magnetic field. Conventionally heated samples in field showed more austenite grain growth compared to inductively heated counterparts. Annealing twin frequency increased under field, with twin density increases not fully explained by larger grain sizes.

Hurley, Megan [University of Florida, Gainesville]↗
DOE OSTI2022

Effects of helium cavity size and morphology on the strength of pure titanium

In this study, high-purity α-titanium was implanted with helium to observe cavity morphology – size, number density, and form (i.e., bubbles vs. voids) – effects on materials strength. Increasing implantation temperatures lead to an Arrhenius-type (i.e., exponential) increase in cavity size, a transition from spherical bubbles to faceted voids, and a marked increase in strength (~20–50%). Implanted samples deformed uniformly in contrast to nano-compression of unimplanted or alloyed titanium, but pillars with the largest faceted voids developed a type of bulging localized deformation. Affected voids were repeatedly sheared, becoming rough and shrunken. Dislocation-cavity interactions and the role of helium content within cavities are considered.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Valley splitting correlations across a silicon quantum well containing germanium

Quantum dots in SiGe/Si/SiGe heterostructures host coherent electron spin qubits, which are promising for future quantum computers. The silicon quantum well hosts near-degenerate electron valley states, creating a low-lying excited state that is known to reduce spin qubit readout and control fidelity. The valley energy splitting is dominated by the microscopic disorder in the SiGe alloy and at the Si/SiGe interfaces, and while Si devices are compatible with large-scale semiconductor manufacturing, achieving a uniformly large valley splitting energy across a many-qubit device spanning mesoscopic distances is an outstanding challenge. In this work we study valley splitting variations in a 1D quantum dot array, formed in a Si 0.972 Ge 0.028 quantum well, manufactured by Intel. We observe correlations in valley splitting, at both sub-100 nm (single gate) and > 1 μm (device) lengthscales, that are consistent with alloy disorder-dominated theory and simulation. Our results develop the mesoscopic understanding of Si/SiGe heterostructures necessary for scalable device design.

Marcks, Jonathan C. [Argonne National Laboratory (↗
DOE OSTI2020

Defect-mediated metastability and carrier lifetimes in polycrystalline (Ag,Cu)(In,Ga)Se 2 absorber materials

Using a combination of optical and electrical measurements, we develop a model for metastable defects in Ag-alloyed Cu(In,Ga)Se 2 , one of the leading thin film photovoltaic materials. By controlling the pre-selenization conditions of the back contact prior to the growth of polycrystalline (Ag,Cu)(In,Ga)Se 2 absorbers and subsequently exposing them to various stresses (light soaking and dark-heat), we explore in this paper the nature and role of metastable defects on the electro-optical and photovoltaic performance of high-efficiency solar cell materials and devices. Positron annihilation spectroscopy indicates that dark-heat exposure results in an increase in the concentration of the selenium–copper divacancy complex (V Se –V Cu ), attributed to depassivation of donor defects. Deep-level optical spectroscopy finds a corresponding increase of a defect at Ev+0.98 eV, and deep-level transient spectroscopy suggests that this increase is accompanied by a decrease in the concentration of mid-bandgap recombination centers. Time-resolved photoluminescence excitation spectroscopy data are consistent with the presence of the V Se –V Cu divacancy complex, which may act as a shallow trap for the minority carriers. Light-soaking experiments are consistent with the V Se –V Cu optical cycle proposed by Lany and Zunger, resulting in the conversion of shallow traps into recombination states that limit the effective minority carrier recombination time (and the associated carrier diffusion length) and an increase in the doping density that limits carrier extraction in photovoltaic devices.

14 SOLAR ENERGY↗
DOE OSTI2021

An efficient numerical model for predicting residual stress and strain in parts manufactured by laser powder bed fusion

Abstract Computational modeling of additively manufactured structures plays an increasingly important role in product design and optimization. For laser powder bed fusion processes, the accurate modeling of stress and distortion requires large amount of computational cost due to very localized heat input and evolving complex geometries. The current study takes advantage of a graphics processing unit accelerated explicit finite element analysis code and approximated heat conduction analysis to predict the macroscopic thermo-mechanical behavior in laser selective melting. Adjacent layers and tracks were lumped to reduce the number of time steps and elements in the finite element model. The effects of track and layer grouping on prediction accuracy and solution efficiency are investigated to provide a guidance for a cost-effective simulation. Thin-wall builds from Inconel alloy 625 (IN625) powders were simulated by applying the developed modeling approach to get the detailed residual stress and distortion at a computational speed 50 times higher than conventional approach. Under repeated heating and cooling cycles, a high tensile stress was produced near surfaces of a build due to a larger shrinkage on surface than that in central area. It is also shown that horizontal stresses concentrate near the root and top layers of the IN625 build. The predicted residual elastic strain distribution was validated by the experimental measurement using x-ray synchrotron diffraction.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Metal Hydride Compressor for High-Pressure (875 bar) Hydrogen Delivery

Metal hydride hydrogen compression utilizes a reversible heat-driven interaction of a hydride-forming metal alloy with hydrogen gas. This paper reports on the development of a laboratory scale two-stage Metal Hydride Compressor (MHC) system with a feed pressure of 150 bar delivering high purity H2 gas at outlet pressures up to 875 bar. Stage 1 and stage 2 AB 2 metal hydrides are identified based on experimental characterization of the pressure-composition-temperature (PCT) behavior of candidate materials. The selected metal hydrides are each combined with expanded natural graphite, increasing the thermal conductivity of the composites by an order of magnitude. These composites are integrated in two compressor beds with internal heat exchangers that alternate between hydrogenation and dehydrogenation cycles by thermally cycling between 20 °C and 150 °C. The prototype compressor achieved compression of hydrogen from 150 bar to 700 bar with an average flow rate of 33.6 g/hr.

08 HYDROGEN↗
DOE OSTI2023

Advances in Binder Jet Additive Manufacturing

Binder Jetting is a powerful additive manufacturing technology due to its low cost and wide range of types of materials it can shape. The industry partner ExOne has a range of binder jet products for applications such as casting tools, composite layup tools, single-alloy metal components, and more. As such, research and development is of high interest in the area of specialized binders for each type of material, processing technology that improves reliability and quality, and materials to enhance the performance of the final parts. Thus, this work focuses on developing novel binders for sand tools and metal prints, new capabilities in multi-material printing, and build monitoring and correction. The result of this work includes a novel binder system that makes binder jet sand stronger than concrete while still being water soluble, a casting binder that is environmentally friendly and produces better surface finishes on castings, and a binder for metals that reduces the residual carbon.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Study of Support Effects for the Water-Gas-Shift Reaction over Cu

The water–gas-shift (WGS) reaction was studied on a series of supported Cu catalysts in which the MgAl 2 O 4 (MAO) support was modified by depositing ZnO, CeO 2 , Mn2O 3 and CoO using Atomic Layer Deposition (ALD). Addition of Cu by one ALD cycle gave rise to catalysts with nominally 1-wt% Cu. A 1.1-wt% Cu/MAO catalyst prepared by ALD exhibited twice the dispersion but ten times the WGS activity of a 1-wt% Cu/MAO catalyst prepared by impregnation, implying that the reaction is structure sensitive. However, Cu catalysts prepared with the ZnO, CeO 2 , and Mn 2 O 3 films showed negligible differences from that of the Cu/MAO catalyst, implying that these oxides did not promote the reaction. Cu catalysts prepared on the CoO film showed a slightly lower activity, possibly due to alloy formation. The implications of these results for the development of better WGS catalysts is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗