SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Rapid-solidification processing yields alloys with improved properties. Study undertaken to extend favorable property combinations of I/M 2XXX alloys through recently developed technique of rapid-solidification processing using powder metallurgy(P/M). Rapid-solidification processing involves impingement of molten metal stream onto rapidly-spinning chill block or through gas medium using gas atomization technique.
This paper describes the research program initiated at the NASA Lewis Research Center for the study of rapid solidification of high temperature materials, with the major purpose for the development of advanced high-temperature and heat-flux materials for aircraft and aerosphace applications. Particular attention is given to the development of three alloys: Ni-aluminides, Nb-alloys, and Cu-alloys. Rapid solidification processing yielded alloys with novel microstructures, very fine grain sizes, reduced chemical segregation, and metastable extended solid solutions.
This Final Report covers the activities completed under the optional program of the NASA HOST Contract, NAS3-23288. The initial effort of the optional program was report-in NASA CR189221, which consisted of high temperature strain controlled fatigue tests to study the effects of thermomechanical fatigue, multiaxial loading, reactive environments, and imposed stresses. The baseline alloy used in the tests included B1900+Hf (with or without coating) and wrought INCO 718. Tests conducted on B1900+Hf included environmental tests using various atmospheres (75 psig oxygen, purified argon, or block exposures) and specimen tests of wrought INCO 718 included tensile, creep, stress rupture, TMF, multiaxial, and mean stress tests. Results of these testings were used to calibrate a CDA model for INCO 718 alloy and to develop modifications or corrections to the CDA model to handle additional failure mechanisms. The Socie parameter was found to provide the best correlation for INCO multiaxial loading. Microstructural evaluations consisting of optical, Scanning Electron Microscopy (SEM), and Transmission Electron Microscopy (TEM) techniques, and surface replication techniques to determine crack initiation lives provided data which were used to develop life prediction models.
This report presents the results of an investigation of the corrosion of aluminum alloy sheet materials used in aircraft. It has for its purpose to study the causes of corrosion embrittlement in duralumin-type alloys and the development of methods for its elimination. The report contains results, obtained in an extensive series of weather-exposure tests, which reveal the extent to which the resistance of the materials to corrosion was affected by variable factors in their heat treatment and by the application of various surface protective coatings. The results indicate that the sheet materials are to be regarded as thoroughly reliable, from the standpoint of their permanence in service, provided proper precautions are taken to render them corrosion-resistant.
Gas turbine engines for future subsonic transports will likely have higher pressure ratios which will require nickel-base superalloy disks with temperature capability up to 1400 F, an increase of about 200 F over current engines. Several advanced disk alloys are being developed to fill this need. One of these, CH98, is a promising candidate for gas turbine engines and is being studied in NASA's AST Program. Additions of the refractory elements tungsten and niobium have been shown to improve tensile and creep properties while maintaining good high temperature fatigue crack growth resistance. Further improvements in creep and crack growth resistance can be achieved with a coarse grain microstructure. The purpose of the present study is aimed at providing a detailed assessment of 0.2 percent creep rates for coarse grain CH98 with tungsten and niobium additions over a range of temperatures and stresses of interest to disk applications.
Gas turbine engines for future subsonic transports will probably have higher pressure ratios which will require nickelbase superalloy disks with 1300 F to 1400 F temperature capability. Several advanced disk alloys are being developed to fill this need. One of these, CH98, is a promising candidate for gas turbine engines and is being studied in NASA's AST Program. For AST applications, compressor/turbine disks must withstand temperatures of 1300 F for several hundred hours over the life of the engine. Additions of the refractory elements tungsten and niobium to CH98 could improve tensile and creep properties, however, the impact on high temperature fatigue crack growth is uncertain. In this paper, these three key properties, tensile, 0.2 percent creep, and fatigue crack growth of CH98 with and without tungsten and niobium additions will be assessed at l300 F.
Gas turbine engines for future subsonic transports will probably have higher pressure ratios which will require nickelbase superalloy disks with 1300 to 1400 F temperature capability. Several advanced disk alloys are being developed to fill this need. One of these, CH98, is a promising candidate for gas turbine engines and is being studied in NASA s Advanced Subsonic Technology (AST) program. For large disks, residual stresses generated during quenching from solution heat treatments are often reduced by a stabilization heat treatment, in which the disk is heated in the range of 1500 to 1600 F for several hours followed by a static air cool and age. The reduction in residual stress levels lessens distortion during machining of disks. Previous work on CH98 has indicated that stabilization treatments will decrease creep capability, however, tungsten additions appear to improve the creep capability of stabilized and aged CH98. In this study, a systematic variation of tungsten additions to CH98 was investigated. Specifically, the 1300 F tensile, creep, and fatigue crack growth properties of stabilized CH 98 were assessed with varying levels of tungsten additions.
Ceramics are generally stable to higher temperatures than most metals and alloys. Thus the development of high temperature structural ceramics has been an area of active research for many years. While the dream of a ceramic heat engine still faces many challenges, niche markets are developing for these materials at high temperatures. In these applications, ceramics are exposed not only to high temperatures but also aggressive gases and deposits. In this chapter we review the response of ceramic materials to these environments. We discuss corrosion mechanisms, the relative importance of a particular corrodent, and, where available, corrosion rates. Most of the available corrosion information is on silicon carbide (SIC) and silicon nitride (Si3N4) monolithic ceramics. These materials form a stable film of silica (SO2) in an oxidizing environment. We begin with a discussion of oxidation of these materials and proceed to the effects of other corrodents such as water vapor and salt deposits. We also discuss oxidation and corrosion of other ceramics: precurser derived ceramics, ceramic matrix composites (CMCs), ceramics which form oxide scales other than silica, and oxide ceramics. Many of the corrosion issues discussed can be mitigated with refractory oxide coatings and we discuss the current status of this active area of research. Ultimately, the concern of corrosion is loss of load bearing capability. We discuss the effects of corrosive environments on the strength of ceramics, both monolithic and composite. We conclude with a discussion of high temperature wear of ceramics, another important form of degradation at high temperatures.
Aircraft propulsion engines for the High Speed Civil Transport which may be developed early in the 21st century will require significantly different durability requirements than those which currently power civil aircraft. The durability will be more difficult to achieve because it is expected that the new aircraft engines will have to operate at near maximum power for more than half of each flight compared to 5 to 10 percent for typical current aircraft. To meet this requirement, a team of NASA, Pratt & Whitney Aircraft, and General Electric personnel have been formed to develop an appropriate alloy for the mission. This report summarizes the work performed by a part of that team up to the retirement of one of its members, R.L. Dreshfield. The prime purpose of the report is to assemble the data obtained in a single document so that it may be more accessible to those who may wish to pursue it at a later date.
As the required service temperatures for superalloys increases, so do the demands on testing for development of these alloys. Non-contact measurement of creep of refractory metals using electrostatic levitation has been demonstrated at temperatures up to 2300 C using samples of only 20-40 mg. These measurements load the spherical specimen by inertial forces due to rapid rotation. However, the first measurements relied on photon pressure to accelerate the samples to the high rotational rates of thousands of rotations per second, limiting the applicability to low stresses and high temperatures. Recent advances in this area extend this measurement to higher stresses and lower-temperatures through the use of an induction motor to drive the sample to such high rotational speeds. Preliminary results on new measurements on new materials will be presented.
A paper describes the Thermal Infrared Sensor (TIRS), a QWIP-based instrument intended to supplement the Operational Land Imager (OLI) for the Landsat Data Continuity Mission (LDCM). The TIRS instrument is a far-infrared imager operating in the pushbroom mode with two IR channels: 10.8 and 12 microns. The focal plane will contain three 640x512 QWIP arrays mounted on a silicon substrate. The silicon substrate is a custom-fabricated carrier board with a single layer of aluminum interconnects. The general fabrication process starts with a 4-in. (approx.10-cm) diameter silicon wafer. The wafer is oxidized, a single substrate contact is etched, and aluminum is deposited, patterned, and alloyed. This technology development is aimed at incorporating three large-format infrared detecting arrays based on GaAs QWIP technology onto a common focal plane with precision alignment of all three arrays. This focal plane must survive the rigors of flight qualification and operate at a temperature of 43 K (-230 C) for five years while orbiting the Earth. The challenges presented include ensuring thermal compatibility among all the components, designing and building a compact, somewhat modular system and ensuring alignment to very tight levels. The multi-array focal plane integrated onto a single silicon substrate is a new application of both QWIP array development and silicon wafer scale integration. The Invar-based assembly has been tested to ensure thermal reliability.
GRCop-42 (Cu-4 at.% Cr-2 at.% Nb) is a copper (Cu)-chromium (Cr)-niobium (Nb) alloy that NASA developed for use in rocket propulsion components that required high thermal conductivity, excellent creep resistance, low-cycle fatigue life, and strength at elevated temperatures, such as combustion chamber liners and fuel injector face plates. Using powder bed fusion (PBF) 3D printing, NASA Marshall Space Flight Center (MSFC) and NASA Glenn Research Center (GRC) successfully printed near-fully-dense GRCop-42 components that may equal to or exceed their traditionally manufactured predecessors. This Technical Memorandum serves to summarize the process that was developed to achieve 3D printable near-fully-dense and functional GRCop-42.
Elementum 3D, in partnership with NASA-MSFC under an ACO, seeks to help further increase launch performance and reduce launch and mission cost by advancing novel additively manufactured (AM) aluminum materials for large-scale complex rocket components and launch vehicle structures. The proposed outcome of this ACO is to advance large-scale directed energy deposition (DED) of highstrength aluminum alloys through process development, characterization, and testing.
The overall Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development and Additive Manufacturing Deployment (“X-P4AM”) project objective is to drastically reduce the time-to-market barriers for new additive alloys of interest in automotive and aerospace applications, through computational alloy design with rapid screening and down- selection via synthesis of candidate alloys with rapid solidification. The project will also refine the technology in high pressure gas atomization to improve the production of commercial quantities of selected powders with high powder yields and enhanced powder quality. A new aluminum (Al) alloy based on an Al-Ce-X composition, enhanced powder production, and optimized AM build parameterization provided a critical step in widespread adoption of AM technology for automotive applications, in this case. The individual background and capabilities of the Party are ideally suited to the successful execution of this work. The included work enhanced the Contractors’ AM capabilities, a core competency of the Contractors, and developed a close working relationship with the Participant in the area of aluminum powder alloys and their end use.
In this work, to develop advanced reduced-activation ferritic-martensitic (RAFM) steels for fusion reactor structural applications, both carbonitride- and carbide-strengthened castable nanostructured alloys (CNAs) were explored for higher densities of MX (M = Ti/Ta/V/etc. and X = C/N) nanoprecipitates. Additionally, systematic comparisons between the two types of CNAs indicated generally similar microstructures and comparable tensile properties and creep resistance. However, the carbide-CNAs did show some advantages over the carbonitride-CNAs in terms of the uniformly distributed higher density of MC nanoprecipitates, greater Charpy impact upper shelf energies, less deuterium retention and swelling, and potentially less transmutation-induced composition changes and consequently thermodynamically more stable carbides. The carbide-CNAs showed the best-balanced high performance in the examined properties, in contrast to the significantly varied performance of oxide-dispersion-strengthened alloys and the generally lower performance of current RAFM steels.
A model has been developed that determines the size of Liquid (sub 11) droplets generated during application of ultrasonic energy (as a function of amplitude) to immiscible alloys. The initial results are in accordance with experimental results based on Succinonitrile - Glycerol "alloys" and pure tin dispersions. Future work will take into account the importance of other effects, e.g., thermo-vibrational convection, sound attenuation, viscosity variations, and compositional changes.
The overall Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development (“X-P4AM”) project objective is to drastically reduce the time-to-market barriers for new additive alloys of interest in automotive and aerospace applications, through computational alloy design with rapid screening and down- selection via synthesis of candidate alloys with rapid solidification. The project will also refine the technology in high pressure gas atomization to improve the production of commercial quantities of selected powders with high powder yields and enhanced powder quality. A new aluminum (Al) alloy based on high entropy composition, enhanced powder production, and optimized AM build parameterization provided a critical step in widespread adoption of AM technology for automotive applications, in this case. The individual backgrounds and capabilities of the Parties are ideally suited to the successful execution of this work. The included work enhanced the Contractors’ AM capabilities, a core competency of the Contractors, and develop a close working relationship with the Participant in the area of aluminum powder alloys and their end use.
Three numerical techniques are employed to analyze the influence of thermosolutal convection on defect formation in directionally solidified (DS) alloys. The finite-element models are based on the Boussinesq approximation and include the plane-front model and two plane-front models incorporating special dendritic regions. In the second model the dendritic region has a time-independent volume fraction of liquid, and in the last model the dendritic region evolves as local conditions dictate. The finite-element models permit the description of nonlinear thermosolutal convection by treating the dendritic regions as porous media with variable porosities. The models are applied to lead-tin alloys including DS alloys, and severe segregation phenomena such as freckles and channels are found to develop in the DS alloys. The present calculations and the permeability functions selected are shown to predict behavior in the dendritic regions that qualitatively matches that observed experimentally.