Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “active lattices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

647 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

In situ deformation of antigorite-olivine two-phase mixtures: Implications for dynamics and seismic anisotropy in the mantle wedge

Water released from hydrous minerals in subducting slabs reacts with the overlying plate, resulting in widespread serpentinization in the mantle wedge. Deformation of serpentinized peridotites has been invoked to explain forearc seismic anisotropy, yet studies of the mechanical properties and deformation behaviors of serpentine-bearing multiphase aggregates remain limited. Here we deformed olivine-antigorite mixtures containing 70, 50, and 20 vol.% of antigorite at 2.5 – 7.6 GPa, 673 K and strain rates of ∼10 –5 –10 –4 s –1 . Elasto-viscoplastic self-consistent simulations, constrained by synchrotron X-ray diffraction (XRD) data, were used to estimate lattice strain, stress–strain partitioning, crystallographic preferred orientations (CPO) development, and aggregate strength. Selected run products were also analyzed by electron backscatter diffraction for comparison with the CPO results obtained from XRD experiments. We found olivine transitions from A- or B-type to C-type when antigorite fraction drops to 20 vol.%, coinciding with a microstructural change from interconnected weak layers to a load-bearing framework (LBF). An additional run on a sample Atg50/Ol50 with preexisting microstructures suggested the formation of LBF was promoted by these microstructures, although the preexisting antigorite CPO has been overprinted at 20.8 % strain and could be erased completely by subsequent deformation in nature. Estimated viscosity of the two-phase mixtures suggests that low-degree serpentinization (≤20 %) in the mantle wedge may increase the strength of olivine-rich peridotite and hinder slab-mantle decoupling, whereas high-degree serpentinization (≥50–70 %) weakens the peridotite and favors decoupling if sufficient viscosity contrast (>10) develops. Seismic anisotropy shows a nonlinear dependence on antigorite fraction: antigorite CPO governs the anisotropy of the mixtures with ≥50 vol.% antigorite, whereas olivine CPO dominates at low fractions (∼20 vol.%). The presence of pre-existing microstructures reduces seismic anisotropy of the deformed mixtures, however the persistence of pre-existing CPO in actively subducting slabs remains uncertain, making their significance over geological timescales questionable.

Crystallographic preferred orientation↗
DOE OSTI2022

Contrasting Trivalent Lanthanide and Actinide Complexation by Polyoxometalates via Solution-State NMR

Deciphering the solution chemistry and speciation of actinides is inherently difficult due to radioactivity, rarity, and cost constraints, especially for transplutonium elements. In this context, the development of new chelating platforms for actinides and associated spectroscopic techniques is particularly important. In this study, we investigate a relatively overlooked class of chelators for actinide binding, namely, polyoxometalates (POMs). We provide the first NMR measurements on americium–POM and curium–POM complexes, using one-dimensional (1D) 31 P NMR, variable-temperature NMR, and spin-lattice relaxation time (T 1 ) experiments. The proposed POM–NMR approach allows for the study of trivalent f-elements even when only microgram amounts are available and in phosphate-containing solutions where f-elements are typically insoluble. The solution-state speciation of trivalent americium, curium, plus multiple lanthanide ions (La 3+ , Nd 3+ , Sm 3+ , Eu 3+ , Yb 3+ , and Lu 3+ ), in the presence of the model POM ligand PW 11 O 39 7– was elucidated and revealed the concurrent formation of two stable complexes, [M III (PW 11 O 39 )(H 2 O) x ] 4– and [M III (PW 11 O 39 ) 2 ] 11– . Interconversion reaction constants, reaction enthalpies, and reaction entropies were derived from the NMR data. The NMR results also provide experimental evidence of the weakly paramagnetic nature of the Am 3+ and Cm 3+ ions in solution. Furthermore, the study reveals a previously unnoticed periodicity break along the f-element series with the reversal of T 1 relaxation times of the 1:1 and 1:2 complexes and the preferential formation of the long T 1 species for the early lanthanides versus the short T 1 species for the late lanthanides, americium, and curium. Furthermore, given the broad variety of POM ligands that exist, with many of them containing NMR-active nuclei, the combined POM–NMR approach reported here opens a new avenue to investigate difficult-to-study elements such as heavy actinides and other radionuclides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Optimizing ensemble NV − spin properties of fluorescent diamond microparticles by systematic low pressure high temperature annealing

Low pressure high temperature annealing is a means for driving nitrogen and defect diffusion in diamond to reduce internal lattice damage without the need for technically complicated high-pressure cells. Herein, we perform a systematic time (5, 15, and 30 min) and temperature (1200 °C–1800 °C) study of effects of low-pressure high temperature annealing on photoluminescence, spin concentrations, and spin relaxation properties of NV centers in ca. 3 μm synthetic type 1b diamond particles. Annealing in the temperature range of ca. 1400 °C–1700 °C for even 5 min leads to a higher optically detected magnetic resonance contrast as compared to standard annealing at 900 °C for 2 h. Particles annealed at 1700 °C for 5 min exhibit a contrast close to about 13% as compared to about 9% for those annealed at 900 °C for 2 h. A reduction in the zero-field splitting strain parameter from E ≈ 4.5 MHz to ≈ 2.5 MHz and spectral linewidth from Δν ≈ 7 MHz to ≈ 4 MHz are observed even after 5 min annealing at 1700 °C. Improvements in these spectral parameters resulted in a roughly 2-fold reduction in the noise level of temperature monitoring experiment utilizing an ensemble of NV centers in the particles. Annealing in the temperature range of 1600 °C for 15 or 30 min or 1700 °C for 5 min resulted in NV T 1 relaxation times approaching ca. 5 ms typically observed for bulk diamond. Quantitative electron paramagnetic resonance (EPR) allowed for estimations of thermal activation energies of paramagnetic center annihilation. Monitoring the primary defect concentration (P1 and other defects with half integer spins) and utilizing second order kinetic modeling, an activation energy of 3.63 ± 0.28 eV was estimated. Alternatively, using the NV half field EPR signal and first order kinetic modeling, a similar activation energy 3.89 ± 0.29 eV was estimated.

NV centers↗
DOE OSTI2026

Electro-chemo-mechanically Driven Ni Exsolution from (Pr,Ce,Ni)O 2−δ : Controlled Nucleation Density and Enhanced Electrode Kinetics

In situ exsolution of metal nanoparticles is a promising strategy to prepare electrocatalysts with enhanced activity and resistance to agglomeration for efficient chemical transformations and energy conversion. Achieving a high nucleation density of nanoparticles under mild conditions and understanding how to tailor the process is important for performance of these electrodes in electrochemical cells. In this work, we demonstrate facile exsolution of Ni nanoparticles using fluorite-structured (Pr,Ce)O 2−δ as the support oxide, driven by electrochemical potential and aided by the metastability of Ni in the solid solution (elastic driving force). We prepare single-phase oriented thin films of (Pr,Ce,Ni)O 2−δ (NPCO) on (Zr,Y)O 2−δ (YSZ) substrates by pulsed laser deposition. With the aid of a high-throughput electrochemical cell that provides a lateral gradient in Nernst voltage, we apply in situ near-ambient pressure synchrotron X-ray photoelectron spectroscopy and ex situ atomic force microscopy to investigate the impact of electrochemical potential on Ni nucleation density. We find that metallic Ni can be successfully exsolved at 550 °C upon cathodic biasing in 20 mTorr O 2 , and its nucleation density increases with increasing electrochemical driving force/decreasing oxygen chemical potential. We further evaluate the electrochemical performance under highly reducing (fuel electrode) conditions by electrochemical impedance spectroscopy. With the exsolved Ni nanoparticles, the surface exchange coefficient of the NPCO is found to be ∼4× higher than for PCO without exsolution. This work confirms mixed conducting fluorites as beneficial host lattices for facile transition-metal exsolution and suggests the possibility for constructing an all ceria-based electrochemical cell with PCO serving as both the cathode and the anode.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Similarities and differences between nickelate and cuprate films grown on a SrTiO 3 substrate

The recent discovery of superconductivity in Sr-doped NdNiO 2 films grown on SrTiO 3 started a novel field within unconventional superconductivity. Therefore, to understand the similarities and differences between nickelate and cuprate layers on the same SrTiO 3 substrate, here based on the density functional theory we have systematically investigated the structural, electronic, and magnetic properties of NdNiO 2 / SrTiO 3 and CaCuO 2 / SrTiO 3 systems. Our results revealed a strong lattice reconstruction in the case of NdNiO 2 / SrTiO 3 , resulting in a polar film, with the surface and interfacial NiO 2 layers presenting opposite displacements. To avoid the “polar catastrophe,” the NiO 2 surface to the vacuum reconstructs as well. However, for CaCuO 2 / SrTiO 3 , the distortions of those same two CuO 2 layers were in the same direction. In addition, we found this distortion to be approximately independent of the studied range of film thickness for the nickelate films. Furthermore, we also observed a two-dimensional electron gas at the interface between NdNiO 2 and SrTiO 3 , caused by the polar discontinuity, in agreement with recent literature. For NdNiO 2 / SrTiO 3 the two-dimensional electron gas extends over several layers, while for CaCuO 2 / SrTiO 3 this electronic rearrangement is very localized at the interface between CaCuO 2 and SrTiO 3 . The electronic reconstruction found at the interface involves a strong occupation of the Ti 3 d x y state. In both cases, there is a significant electronic charge transfer from the surface Ni or Cu layers to the Ti interface layer. The interfacial Ni and Cu layers are hole and electron doped, respectively. By introducing magnetism and electronic correlation, we observed that the d 3 z 2 - r 2 orbital of Ni becomes itinerant while the same orbital for Cu remains doubly occupied, establishing a clear two- vs one-orbital active framework for the description of these systems. Furthermore, we also observed a strong magnetic reconstruction at the NdNiO 2 surface to vacuum layer where magnetism is basically suppressed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Formation and Detriments of Residual Alkaline Compounds on High-Nickel Layered Oxide Cathodes

High-nickel layered oxides LiNi x M 1-x O 2 (x ≥ 0.9) have emerged as promising cathode materials for automotive batteries due to their high energy density and lower cost. However, the formation and accumulation of surface alkaline compounds during storage hinder their mass production and commercialization. Here, in this study, a validated chemical method is employed to deconvolute and quantify the evolution of each residual lithium compound in four representative cathodes during ambient-air storage, viz., LiNiO 2 (LNO), LiNi 0.95 Co 0.05 O 2 (NC), LiNi 0.95 Mn 0.05 O 2 (NM), and LiNi 0.95 Al 0.05 O 2 (NA). Furthermore, the activation energy of the reaction between water and the cathode is determined by measuring the leached LiOH concentration at various temperatures. While residual lithium and time-of-flight secondary-ion mass spectrometry measurements collectively reveal that the air stability overall follows the trend of NM > NA ≈ NC > LNO, the aged NM exhibits the highest charge-transfer resistance and the worst electrochemical performance among the cathodes. In situ, X-ray diffraction and scanning transmission electron microscopy unveil that the aged NM is plagued by a large area of resistive spinel-like M 3–x Li x O 4 phases, leading to aggravated particle reaction heterogeneity. Finally, a one-step recalcination method is demonstrated effective in fully restoring the degraded cathodes. This work provides insights into overcoming air sensitivity issues of high-Ni cathodes.

(S)TEM↗
DOE OSTI2023

Microscopic Investigation of H 2 Reduced CuO x /Cu(111) and ZnO/CuO x /Cu(111) Inverse Catalysts: STM, AP-XPS, and DFT Studies

Understanding the reduction mechanism of ZnO/CuO x interfaces by hydrogen is of great importance for advancing the performance of industrial catalysts for CO 2 hydrogenation to methanol. Here, the reduction of pristine and ZnO-modified CuO x /Cu(111) by H 2 was investigated using ambient pressure scanning tunnelling microscopy (AP-STM), ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and density functional theory (DFT). The morphological changes and reaction rates seen for the reduction of CuO x /Cu(111) and ZnO/CuO x /Cu(111) are very different. On CuO x /Cu(111), perfect "44" and "29" structures displayed a very low reactivity towards H 2 at room temperature. A long induction period associated with an autocatalytic process was observed to enable the reduction by the removal of chemisorbed non-lattice oxygen initially and lattice oxygen sequentially at the CuO x -Cu interface, which led to formation of oxygen deficient "5-7" hex and honeycomb structures. In the final stages of the reduction process, regions of residual oxygen species and metallic Cu were seen. The addition of ZnO particles to CuO x /Cu(111) opened new reaction channels. On the ZnO sites, the dissociation of H 2 was fast and H adatoms easily migrated to adjacent regions of copper oxide. This hydrogen spillover substantially enhanced the rate of oxygen removal, resulting in the rapid reduction of the copper oxide located in the periphery of the zinc oxide islands with no signs for the reduction of ZnO. The deposited ZnO completely modified the dynamics for H 2 dissociation and hydrogen migration, providing an excellent source for CO 2 hydrogenation processes on the inverse oxide/metal system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Engineering of a Coupled Nanocomposite as a High-Performance Protonic Ceramic Fuel Cell Cathode

The lack of high-performance cathode catalysts is a salient issue that bedeviled the commercialization of protonic ceramic fuel cells (PCFCs). Here, in this work, we report a remarkable electrocatalytic activity and stability enhancement of cathode electrodes by engineering a coupled nanocomposite. The as-prepared Pr 0.3 (Ba 0.5 Sr 0.5 ) 0.7 Co 0.8 Fe 0.2 O 3−δ nanocomposite possesses a bulk cubic phase on which homogeneous and intimate orthorhombic PrCo 0.5 Fe 0.5 O 3−δ nanoparticles are uniformly decorated. X-ray diffraction and Raman spectroscopy reveal the excellent thermal stability of the nanocomposite. It achieves a high peak power density of 1.02 W cm –2 based on protonic electrolytes at 600 °C. No noticeable structural degradation is observed over ∼210 h at 550 °C according to scanning electron microscopy analysis. This work demonstrates an effective strategy to boost the performance of perovskite oxides for PCFCs via nanocomposite engineering. It may apply to other catalyst designs and discoveries, such as for batteries, electrolyzers, and membrane reactors.

08 - HYDROGEN↗
DOE OSTI2024

Trap Passivation for Reducing On-Resistance and Saturation Voltage in Wafer-Bonded InGaAs-Channel/GaN-Drain Vertical FETs

High frequency and high power are the driving forces behind semiconductor transistor technology. However, conventional devices have the tradeoff of either being high speed or high breakdown—but not both. Wafer-bonded current aperture vertical electron transistors (BAVETs) help eliminate the tradeoff by combining a high-speed III-As channel to a high-breakdown III-N drift region. The device presented herein comprises of an InAlAs gate-barrier/InGaAs channel, wafer-bonded to an InGaN/GaN drift region, with the InGaAs/InGaN interface referred to as the wafer-bonded interface (WBI). The electronic behavior of WBIs is yet less known but necessary in realizing the potential of a BAVET. Herein, strong trap activity at the WBI is shown to be the cause of abnormally high saturation voltage ( V DS_SAT ) in BAVETs. The traps cause unintentional space charge (SC) region in the drain region of the device. This causes a drain resistance, a higher ON-resistance ( R ON ), and a higher V DS_SAT . Here, the challenge is overcome by hydrogen passivation of traps at WBI by using a p-doping for the InAlAs layer, which reduces the trap-charge concentration at the WBI. Consequently, the width of the SC region is reduced and a reduction in V DS_SAT is demonstrated, wherein it reduces from >12 to 5 V.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structure of V-defects in long wavelength GaN-based light emitting diodes

The V-defect is a naturally occurring inverted hexagonal pyramid structure that has been studied in GaN and InGaN growth since the 1990s. Strategic use of V-defects in pre-quantum well superlattices or equivalent preparation layers has enabled record breaking efficiencies for green, yellow, and red InGaN light emitting diodes (LEDs) utilizing lateral injection of holes through the semi-polar sidewalls of the V-defects. In this article, we use advanced characterization techniques such as scattering contrast transmission electron microscopy, high angle annular dark field scanning transmission electron microscopy, x-ray fluorescence maps, and atom probe tomography to study the active region compositions, V-defect formation, and V-defect structure in green and red LEDs grown on (0001) patterned sapphire and (111) Si substrates. We identify two distinct types of V-defects. The “large” V-defects are those that form in the pre-well superlattice and promote hole injection, usually nucleating on mixed (Burgers vector b = ±a±c⁠) character threading dislocations. In addition, “small” V-defects often form in the multi-quantum well region and are believed to be deleterious to high-efficiency LEDs by providing non-radiative pathways. The small V-defects are often associated with basal plane stacking faults or stacking fault boxes. Furthermore, we show through scattering contrast transmission electron microscopy that during V-defect filling, the threading dislocation, which runs up the center of the V-defect, will “bend” onto one of the six {10$\overline{1}$1} semi-polar planes. In conclusion, this result is essential to understanding non-radiative recombination in V-defect engineered LEDs.

42 ENGINEERING↗
DOE OSTI2024

Accelerating the Discovery of New, Single Phase High Entropy Ceramics via Active Learning

High-entropy ceramics have garnered interest due to their remarkable hardness, compressive strength, thermal stability, and fracture toughness; yet the discovery of new high-entropy ceramics (out of a tremendous number of possible elemental permutations) still largely requires costly, inefficient, trial-and-error experimental and computational approaches. The entropy forming ability (EFA) factor was recently proposed as a computational descriptor that positively correlates with the likelihood that a 5-metal high-entropy carbide (HECs) will form the desired single phase, homogeneous solid solution; however, discovery of new compositions is computationally expensive. If you consider 8 candidate metals, the HEC EFA approach uses 49 optimizations for each of the 56 unique 5-metal carbides, requiring a total of 2744 costly density functional theory calculations. Here, we describe an orders-of-magnitude more efficient active learning (AL) approach for identifying novel HECs. To begin, we compared numerous methods for generating composition-based feature vectors (e.g., magpie and mat2vec), deployed an ensemble of machine learning (ML) models to generate an average and distribution of predictions, and then utilized the distribution as an uncertainty. Here we then deployed an AL approach to extract new training data points where the ensemble of ML models predicted a high EFA value or was uncertain of the prediction. Our approach has the combined benefit of decreasing the amount of training data required to reach acceptable prediction qualities and biases the predictions toward identifying HECs with the desired high EFA values, which are tentatively correlated with the formation of single phase HECs. Using this approach, we increased the number of 5-metal carbides screened from 56 to 15,504, revealing 4 compositions with record-high EFA values that were previously unreported in the literature. Our AL framework is also generalizable and could be modified to rationally predict optimized candidate materials/combinations with a wide range of desired properties (e.g., mechanical stability, thermal conductivity).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microkinetic simulation and fitting of the temperature programmed reaction of methanol on CeO 2 (111): H 2 and H 2 O + V production

The kinetics and mechanism for temperature programmed reaction following adsorption of an adsorbate can be better understood by simulation and fitting with comparison to experiment. A case study is presented here for the chemistry of adsorption of methanol on a CeO 2 (111) surface followed by heating. The gas products observed are CH 3 OH, CH 2 O, H 2 , H 2 O, CO, CO 2 . At low temperatures (< 500 K), there is formation of H 2 and H 2 O, where the H 2 O formation is accompanied by lattice oxygen vacancy (V) formation and is thus important in determining the selectivity towards different products. Microkinetic modeling was performed using a recently published method for fitting to gain mechanistic knowledge of the H 2 and H 2 O + V formation at < 500 K. In the kinetic models used here, most of the H 2 and H 2 O + V V formation can be explained by a mechanism in which a metastable state of hydrogen on the surface (H*) acts as an intermediate. Two possibilities were investigated for the source of the metastable H* intermediate: H* from CH bond breaking of methoxies, or promotion of H+ to H* via electron transfer from ionic methoxies absorbed in oxygen vacancies (CH 3 O - /V). From this study, we consider the latter to be more likely at < 500 K. For the H 2 O formation, it was found to be critical that H 2 O cannot dissociate directly on oxygen vacancies. Finally, catalytic chemistry was observed in simulations, including catalytic formation of oxygen vacancies. Various features of the experimental results were reproduced, including methoxies being the major carbon containing species on the surface at < 500 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis, Processing, and Use of Isotopically Enriched Epitaxial Oxide Thin Films

Isotopic engineering has emerged as a key approach to study the nucleation, diffusion, phase transitions, and reactions of materials at an atomic level. It aims to uncover mass transport pathways, kinetics, and operational and failure mechanisms of functional materials and devices. Understanding these phenomena leads to deeper insights into important physical processes, such as the transport of ions in energy conversion and storage devices and the role of active sites and supports during heterogeneous catalytic reactions. Likewise, isotopic engineering is being pursued as a means of modifying functionality to enable future technological applications. In this Account, we summarize our recent work employing isotope labeling (e.g., 18 O 2 and 57 Fe) during thin film synthesis and postgrowth processing to reveal growth mechanisms, defect chemistry, and elemental diffusion under working and extreme conditions. Isotope-resolved analysis techniques with nanometer-scale spatial resolution, such as time-of-flight secondary ion mass spectrometry and atom probe tomography, facilitate the accurate quantification of isotopic placement and concentration in our well-defined heterostructures with precisely positioned, isotope-enriched layers. By measuring the nanometer-scale redistribution between natural abundance and isotopically enriched oxygen layers during the deposition of Fe 2 O 3 and Cr 2 O 3 by molecular beam epitaxy, we identified intermixing processes driven by surface adatoms occurring both at the film growth surface and within the first few layers below the surface. Further insights into synthesis mechanisms were gained by studying the tungsten oxide thin films grown by evaporating WO 3 powder in the presence of background 18 O 2 , revealing minimal incorporation of background oxygen during the film formation process. Thermal and radiation-enhanced diffusion in epitaxial Fe and Cr oxides were precisely tracked using 18 O and 57 Fe tracer layers incorporated into model epitaxial oxide thin films. This approach has allowed us to access thermal diffusion behavior at lower temperatures than previously measured, revealing a potential changeover in diffusion mechanism. Understanding radiation-enhanced diffusion in model oxides that represent the surface layers on the structural components of nuclear reactors informs our understanding of their corrosion behavior under irradiation. Isotopic labeling can also provide unique insights into the surface exchange reactions and defect chemistry of electrocatalysts. For instance, tracking the change in 18 O concentration at the surface of an epitaxial LaNiO 3 thin film after the electrocatalytic oxygen evolution reaction revealed the participation of lattice oxygen, confirming a hypothesis that had been proposed previously. Lastly, we highlight a new direction wherein we perform in situ processing studies utilizing isotopic tracers in conjunction with model epitaxial thin films within the atom probe tomography instrument. Additionally, this Account illustrates the great potential of isotopic engineering to enable fundamental mechanistic insights into physical processes and engineer functional properties in epitaxial films, heterostructures, and superlattices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Active Cancellation of Servo-Induced Noise on Stabilized Lasers via Feedforward

Many precision laser applications require active frequency stabilization. However, such stabilization loops operate by pushing noise to frequencies outside their bandwidth, leading to large “servo bumps” that can have deleterious effects for certain applications. The prevailing approach to filtering this noise is to pass the laser through a high-finesse optical cavity, which places constraints on the system design. Here, we propose and demonstrate a different approach where a frequency error signal is derived from a beat note between the laser and the light that passes through the reference cavity. The phase noise derived from this beat note is fed forward to an electro-optic modulator after the laser, carefully accounting for relative delay, for real-time frequency correction. With a hertz-line-width laser, we show ≳20 dB noise suppression at the peak of the servo bump (approximately 250 kHz) and a noise-suppression bandwidth of approximately 5 MHz—well beyond the servo bump. By simulating the Rabi dynamics of a two-level atom with our measured data, we demonstrate substantial improvements to the pulse fidelity over a wide range of Rabi frequencies. Here, our approach offers a simple and versatile method for obtaining a clean spectrum of a narrow-line-width laser, as required in many emerging applications of cold atoms, and is readily compatible with commercial systems that may even include wavelength conversion.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

MOCVD Growth and Characterization of ZnSnN 2

Since the first few reports of its synthesis in 2011 and 20121-3, interest in ZnSnN 2 for diverse applications, including photovoltaics1,3,4, visible light photocatalysis5, and optoelectronics, has been growing. Novel nitride-based LED device designs promise high gains in efficiency at emission wavelengths into the green, amber and even red.6-8 Their realization requires the precise insertion of an ultrathin layer of ZnGeN 2 or ZnSnN 2 into the active region of an InGaAs-GaAs LED structure. While thin films of ZnSnN 2 have been synthesized by RF sputtering1,9 and by MBE 2,10,11, and thin films of ZnGeN 2 , ZnSiN 2 and their alloys by MOCVD, the synthesis of ZnSnN 2 thin films by MOCVD has not yet been reported. It is a challenging goal, given the narrow temperature window between efficient activation of ammonia and the thermal decomposition of ZnSnN 2 at near-atmospheric pressures. We report here the results of studies of ZnSnN 2 films grown on r- and c-plane sapphire substrates, GaN templates on sapphire, and In 0.15 Ga 0.85 N templates on GaN-on-sapphire, at temperatures from 500 °C to 560 °C, using tetramethyltin (TMSn), diethylzinc (DEZn), germane and ammonia. Chamber pressures were varied between 200 and 500 torr. In addition, the ratios of the cation precursors and the total cation-to-anion precursor ratios were varied. Single crystal growth, as evidenced by 2θ-ω x-ray diffraction scans, was achieved on all of these substrates. Wurtzitic (0002) ZnSnN 2 diffraction were observed at 2θ ~ 32.90 for the samples grown on c-sapphire, GaN (0001) and InGaN (0001) templates, and wurtzitic (11-20) peak at 2θ ~ 54.80 for the films grown on r-sapphire. Higher pressures and higher temperatures promoted better crystallinity and more continuous films, as revealed by scanning electron microscopy (SEM) images and 2θ-ω x-ray diffraction peak widths and intensities. Crystal quality was observed to be highly dependent on growth temperature. For example, in one series a 10 °C change in growth temperature resulting in a factor of 15 increase in diffraction peak intensity. SEM images show that films grown on the GaN templates had better uniformity in nucleation than those grown on sapphire. The presence of satellite peaks around the Bragg peak in the XRD 2θ-ω scan for a film grown on a GaN template, and the absence of satellite peaks for the films grown simultaneously on c- and r-sapphire, also indicate superior quality for the film grown on GaN. HAADF-STEM images of films grown on these templates showed smooth interfaces at the film-substrate boundary and show growth rates as high as 167 nm/h, considerably higher than reported previously for MBE growth.9,10 Electron diffraction patterns show single crystallinity. Rocking curves show FWHM as low as 0.100. RMS surfaces roughnesses, measured by atomic force microscopy, are of the order of 3 nm for 1µm x 1µm areas. Current work is focusing on optimizing growth on InGaN templates. These templates are promising for their relatively lower lattice mismatch with ZnSnN 2 . Their use is a next step toward producing LED device structures.

Jayatunga, Benthara Hewage Dinushi↗
DOE OSTI2024

Molecular-Resolution Electron Imaging of Defects and Dynamics at the Ice-Water Interface

Water crystallization into hexagonal ice (type I h ) is one of the most critical processes relevant to the Earth’s environment and human activities. However, despite recent breakthroughs in imaging non-equilibrium condensed ice structures, the ice-water interface has never been imaged at a molecular resolution. This is primarily due to the low stability of the hydrogen bonds in ice under high-resolution microscopy conditions and a lack of methods to prepare compatible samples. Here, this presentation describes the first molecular-resolution imaging of ice crystallized from liquid water and the ice-water interface using high-resolution transmission electron microscopy (HRTEM). By encapsulating deionized (DI) water between two amorphous carbon (a-C) TEM grids and subsequently freezing it with liquid N 2 on a cryo sample stage, we generated two types of ice: non-equilibrium, condensed ice from the atmosphere and encapsulated ice from the DI water (Fig. 1A). Condensed ice usually shows irregular, spherulitic shapes (Fig. 1B). Selected area electron diffraction (SAED) shows that they are a mixture of cubic and hexagonal crystals (Fig. 1C). On the contrary, encapsulated ice forms thin films that contain large-area single-crystalline regions of hexagonal ice oriented along the [0001] zone axis (Fig. 1D). Differential electron energy-loss spectroscopy (EELS) confirmed the high purity of the encapsulated ice free from organic contaminations that are common in other encapsulation methods for HRTEM such as graphene liquid cells. These single-crystalline areas are robust under the electron beam up to ~100 e/Å 2 s. Aberration-corrected HRTEM imaging in these areas achieved a line resolution of ~1.3 Å (Fig. 1E and F). This platform allows us to study near-equilibrium ice structures and dynamics at an unprecedented spatial resolution (Fig. 2). For example, we discovered subdomain-rich regions near the defective crystal edges despite the structure appearing single-crystalline according to diffraction criteria. These subdomains connect via low-angle grain boundaries with flat energy landscapes as a function of tilt angles (according to simulations), showing the high tolerance of ice to defect structures. When we tuned the sample temperature and electron flux rate, we observed radiolysis-controlled bubble generation and dissolution in ice single crystals near a steady state of bubble dynamics. Furthermore, rich beam-induced melting and recrystallization dynamics were observed at the ice-water interface with lattice resolution. These data represent the first observation of the ice-water phase transformation at the sub-nanometer level. In summary, the methods developed in this work enabled molecular-resolution observations of ice and the ice-water interface and shed light on the microstructures and phase transformation pathways. Finer control on the temperature, electron irradiation profile, and imaging detector could eventually lead to real-time observation of ice nucleation in water and address long-standing questions in the nucleation pathways.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Iodine Co-Precipitation with Calcium Carbonate in the Presence of Silica Ions - 20360

Historical releases of I-129 to the subsurface at the U.S. Department of Energy Hanford Site have resulted in large dilute plumes that cover an area of over 50 km{sup 2}. The most concentrated I-129 plume is associated with the 200 West Area in the 200-UP-1 operable unit of the Hanford Central Plateau, where peak concentrations have been measured up to 30 times the drinking water standard of 1 pCi/L. The mobility of iodine depends on many factors, including chemical speciation, pH, redox conditions, as well as the presence of organic matter, calcium carbonate minerals and microbial activities. Speciation measurements estimate that the majority of the iodine (∼76%) in Hanford groundwater exists as iodate. Information on processes that affect iodate mobility in the Hanford subsurface support evaluation of environmental management options for the I-129 plumes. Iodate can be incorporated into calcium carbonate, which is a potential mechanism of naturally attenuating radioiodine in groundwater. However, the silica content in porewater may impact the contaminant-calcium carbonate incorporation process. Silica is one of the most abundant elements in nature and can have an impact on chemical weathering of alkaline-earth carbonates in the environment. Hence, this research aims to advances knowledge of the iodine co-precipitation process with calcium carbonate in the presence of silica. This information supports the technical basis evaluation of natural attenuation for I-129. Samples for these studies were prepared using calcium carbonate-forming solutions that included certified grade sodium meta-silicate nonahydrate (Na{sub 2}SiO{sub 3}), calcium chloride dehydrate (CaCl{sub 2}.2H{sub 2}O), sodium carbonate (NaCO{sub 2}), and sodium hydroxide (NaOH) solutions for pH adjustments. Triplicate samples were prepared with silica concentrations in the solution of 0 mM, 0.5 mM and 20 mM, mixed with an iodate standard (1000 ppm of IO{sub 3}{sup -} in H{sub 2}O) and sampled over a one-week period. Preliminary data analyses suggest that less iodine remains in solution in the presence of silica (average remaining aqueous fraction 0.23±0.03 at 20 mM of Si) relative to samples without silica (0.52±0.06); an indication that more iodine has been sorbed or incorporated into precipitates. However, the mechanisms for this behavior are still under investigation and need to be interpreted relative to pore water compositions that are representative of Hanford site-specific conditions. Scanning electron microscope equipped with energy dispersive spectroscopy (SEM-EDS) analyses were performed to observe the solid phase morphology in these experiments and showed rhombohedral calcite crystals covered with amorphous Si floccules. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗