Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “acceleration response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

In-situ proton radiation testing of 2.4 micron wavelength extended InGaAs photodiodes at dry ice and room temperatures

We have successfully tested 290 µm diameter, 2.4 micron wavelength, Extended InGaAs photodiodes coupled with single mode fiber using 50 MeV Protons at both dry ice temperature (-72 °C) and room temperature (20 °C). The devices were reverse biased at 100 mV during the radiation run and their leakage current was continuously monitored insitu during the exposure. These devices find multiple applications in space for spectroscopy & sensing, inter-satellite optical communication links, rapid Doppler shift LIDAR, as well as inter-planetary and Earth-to-Moon communication links. Several photodiodes were tested using 50 MeV Protons with an average flux level of 2.11 × 10 7 protons/cm 2 /s, for a total fluence of 1.0 × 10 11 protons/cm 2 and total dose of 20 krad (water). Pre- and post-radiation results were also measured for leakage current vs. voltage, responsivity (quantum efficiency), and bandwidth of the Extended InGaAs photodiodes. Finally, all devices were found to be fully functional at normal operating conditions and at both dry ice and room temperature.

2.4 micron wavelength↗
DOE OSTI2022

Post-hazard condition assessment of nuclear piping-equipment systems: Novel approach to feature extraction and deep learning

Over the past decade, the use of artificial intelligence techniques in the field of health-monitoring has gained significant interest, especially for structures such as building and bridges. However, applications to industrial systems such as equipment-piping systems in nuclear plants have not been explored. Here, in this paper, it is shown that the existing techniques developed for buildings and bridges cannot be extended directly to equipment-piping systems as the response of such systems is governed by multiple localized modes unlike that in buildings and bridges. This paper proposes a new approach that consists of three key aspects: (i) a novel vector of degradation-sensitive features extracted from measured data, (ii) using a deep Artificial Neural Network (ANN) for diagnosis of degradation location and degradation severity, and (iii) consideration of uncertainty in degradation severity when training the ANN. Degradation in piping-equipment systems can occur due to flow-accelerated erosion and corrosion. These locations can potentially exhibit damage such as localized yielding or initiation of cracking due to an external event such as an earthquake. Moreover, such locations can at times go undetected by current inspection techniques. Therefore, a robust framework is needed for detection of degradation after a seismic event. This manuscript proposes a proof-of-concept framework, which utilizes data collected from sensors to generate a deep ANN database for predicting degraded locations and severity in a piping-equipment system. Degradation severity is classified as minor, moderate, and severe. In the suggested methodology, a novel vector of degradation-sensitive features is extracted from the sensor data to train the ANN. A simple piping-equipment system is selected to demonstrate feature extraction as a means to simplify pattern recognition, explore the design and parameters of an ANN, and develop a sensor placement strategy. The effectiveness of the proposed framework is demonstrated on a realistic primary safety system of a two-loop nuclear reactor. It is shown that the proposed post-hazard condition assessment framework is able to detect degraded locations along with the severity levels, including minor degradation, with considerably higher accuracy.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Ultrafast Relaxation of MLCT Excited States in Manganese Tricarbonyl Complexes: Insights from Polarization-Resolved Femtosecond X-ray Absorption Spectroscopy at the Mn and Br K-Edges

Optical absorption features that are often described as metal-to-ligand charge transfer (MLCT) bands underlie the utility of many metal coordination complexes by harnessing the energy of light to drive otherwise inaccessible chemical reactions. Excitation of these bands triggers rapid electronic dynamics that can be challenging to understand, due to complicated potential energy landscapes and highly correlated electronic and nuclear degrees of freedom in metal-containing compounds. The lowest-energy absorption bands in Mn complexes containing alpha-diimine, carbonyl, and halide ligands are particularly interesting, due to the delocalized nature of charge transfer upon excitation. Here, in this study, we report experimental ultrafast dynamics measurements for the series of compounds Mn­(CO) 3 ( R bpy)Br ( R bpy = 4,4′-disubstituted-2,2′-bipyridine; R = H, CF 3 , or NO 2 ) using polarization-resolved, femtosecond X-ray absorption spectroscopy (XAS) at both the Mn and Br K edges. The appearance of a new absorption feature in the Br pre-edge spectrum upon optical excitation reveals the instantaneous formation of an electronic hole that is partially localized on the Br atom and has a lifetime that depends on the electron withdrawing character of the R bpy ligand. For two of the complexes (R = H or CF 3 ), a large expansion of the Mn–Br distance results in a rapid redistribution of the hole and a corresponding decrease in anisotropy of the absorption feature within 50 fs, after which the absorption into the hole disappears on a time scale shorter than 300 fs. We observe a different result for the NO 2 substituted compound, for which the Mn–Br bond contracts and the absorption into the Br-centered hole persists beyond the 2 ps time scale of our measurement. The Mn pre-edge spectrum also reveals structural changes for these three complexes, but the new Mn absorption features become evident only after the nuclei respond to the initial excitation, which allows mixing of Mn 3d and 4p orbitals. The combined use of ultrafast Mn and Br K-edge spectroscopy provides unique insight into the ways in which bipyridine substitution alters the excited-state dynamics, including a very different structural response for the most strongly electron withdrawing substituent.

Otolski, Christopher J. [Univ. of Kansas, Lawrence↗
DOE OSTI2025

Closing the Accuracy Gap in Tandem Photovoltaic Testing: An Accessible and Efficient Spectral Tuning Method Using LED-Based Simulators for Research Laboratories and Industry

Accurate performance calibration of multijunction (MJ) solar cells is critical for advancing this technology toward large-scale terrestrial application, yet existing testing methods developed by photovoltaics calibration laboratories remain prohibitively complex and resource intensive for most research laboratories. Current approaches rely on expensive multisource simulators and/or intricate spectral tuning algorithms, limiting accessibility and hindering standardized comparisons of emerging MJ technologies such as perovskite-based tandems. This paper introduces a streamlined spectral irradiance adjustment method for light-emitting diode (LED)-based solar simulators, which are increasingly adopted in the photovoltaics community due to their versatility and cost-effectiveness. The method we present bins LED channels into groups based on the number of junctions of the MJ photovoltaic device under test (DUT) and their corresponding band gaps and incorporates an automated tuning algorithm that eliminates the need to adjust each channel’s irradiance individually. This tuning algorithm requires the relative spectral responsivities of both the DUT and a broadband reference cell, as well as a calibrated spectroradiometer. Measurement validation across various MJ devices, including III-V and perovskite/silicon tandems, demonstrates excellent agreement within 1% with well-established xenon-tungsten multisource simulators and associated tuning algorithms. By enabling precise spectral tuning with readily available equipment and a simple tuning algorithm, our approach bridges the measurement accuracy gap between research laboratories and accredited testing facilities, fostering more reliable device comparisons and accelerating the translation of MJ technologies into real-world energy systems.

14 SOLAR ENERGY↗
DOE OSTI2022

Solar Photovoltaics: Supply Chain Deep Dive Assessment

This is one of a series of reports and deep dive assessments produced in response to Executive Order 14017 “America’s Supply Chains,” which directs the Secretary of Energy to submit a report on supply chains for the energy sector industrial base. The Executive Order is helping the federal government to build more secure and diverse U.S. supply chains, including energy supply chains. Over the past decade, solar power has gone from an emerging, niche technology to a mature energy industry. By 2035, solar power could supply 40% or more of U.S. electricity demand, dramatically accelerating the decarbonization of buildings, transportation, and industry; and, if current technology trends continue, it could do so without increasing the price of electricity. The rapid expansion of solar energy has the potential to yield broad benefits in the form of economic activity and workforce development. The solar industry already employs roughly 230,000 people in the United States, at an average wage that is higher than the national average for most comparable positions. By decarbonizing the electricity sector by 2035, the U.S. solar industry could employ 500,000–1,500,000 people by 2030. The components that are assembled to install a photovoltaic power system are produced by a global supply chain. Photovoltaic (PV) modules (also called panels) are made of cells that use a variety of technologies. There are two leading types of solar modules used in the United States, with crystalline silicon (c-Si) modules representing 84% of the market and cadmium telluride (CdTe) modules representing 16% of the market. Modules of either type require mounting structures to provide mechanical support (racking), which may be configured to follow the sun (tracking). The output of any PV module is direct current (dc), which is almost always converted to alternating current (ac) by an inverter.

14 SOLAR ENERGY↗
DOE OSTI2025

No evidence of a reduction in the dipole polarisability at shell closures

Photoabsorption reactions have a long and productive history as probes of the response of nuclei to electromagnetic fields. In recent years, there has been a suggestion that the dipole polarisability may be reduced at shell closures, potentially due to the reduced level density. In the current paper, more recent photoabsorption strengths are reanalysed including nuclei on closed proton shells to search for a similar reduction. The previously reported reduction is not reproduced. We conclude that the previously observed reduction may be due to incomplete evaluations of the photoabsorption due to missing cross section contributions and experimental artefacts. More experimental data are necessary to draw a firm conclusion about whether shell effects persist into high excitation energies, especially data which can obviate any systematic effects and look at relative photoabsorption strengths between nuclei.

Giant dipole response↗
DOE OSTI2021

Carbonation of model cement pastes: The mineralogical origin of microstructural changes and shrinkage

This study explored the reactive processes of atmospheric carbonation and the consequences with respect to cementitious materials. Two model pastes were used: hydrated C{sub 3}S (including C-S-H and portlandite) and a paste prepared by hydrating a blend of C{sub 3}S and nanosilica (including C-S-H only). The two pastes were carbonated under accelerated conditions in the laboratory. The resulting mineralogical assemblage was examined using X-ray diffraction, thermogravimetric analysis and nuclear magnetic resonance. The microstructural changes were studied by X-ray tomography and porosimetry, and their macroscopic impacts were evaluated through gas diffusion and shrinkage measurements. The use of model pastes allowed for the evaluation of the change in solid volume induced by the carbonation of C-S-H. C-S-H decalcification and subsequent silica chain polymerisation were found responsible for carbonation shrinkage (and potentially cracking). Finally, the results highlight the protective role of portlandite: portlandite helped in limiting C-S-H decalcification and then reducing carbonation shrinkage and cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spatiotemporal Modeling of Real World Backsheets Field Survey Data: Hierarchical (Multilevel) Generalized Additive Models

Assessing photovoltaic module backsheet durability is critical to increasing module lifetime. Laboratory-based accelerating testing has recently failed to predict large scale failures of widely adopted polymeric materials. Additionally, there is a growing concern on characterizing the non-uniformity of field exposure. Therefore, data from field surveys are critical to assess the performance of component lifetimes. Using a documented field survey protocol, 19 field surveys were conducted. The focus of this survey strategy is to investigate spatial continuity in degradation modes. By combining field survey data with real-time satellite weather data, stressor / response models have been trained. Generalized additive Models (GAM) model was created to predict the value of degradation based on measured predictors. Two different GAM constructions were testing using different implementations of basis splines. The model includes variables on the environmental stressors of the system and the location of each measurement in the PV mounting structure. The incorporation of hierarchical structure into the models allowed for material specific degradation rates, while maintaining the assumption of a global trend. The model performed well with an adjusted R2 of 0.975 for yellowness index prediction.

backsheet↗
DOE OSTI2022

On the Role of Interfacial Water Dynamics for Electrochemical Stability of RuO 2 and IrO 2

Abstract Based on the coincident onsets of oxygen evolution reaction (OER) and metal dissolution for many metal‐oxide catalysts it was suggested that OER triggers dissolution. It is believed that both processes share common intermediates, yet exact mechanistic details remain largely unknown. For example, there is still no clear understanding as to why rutile IrO 2 exhibits such an exquisite stability among water‐splitting electrocatalysts. Here, we employ density functional theory calculations to analyze interactions between water and the (110) surface of rutile RuO 2 and IrO 2 as a response to oxygen evolution involving lattice oxygen species. We observe that these oxides display qualitatively different interfacial behavior that should have important implications for their electrochemical stability. Specifically, it is found that IrO 2 (110) becomes further stabilized under OER conditions due to the tendency to form highly stable low oxidation state Ir(III) species. In contrast, Ru species at RuO 2 (110) are prone to facile reoxidation by solution water. This should facilitate the formation of high Ru oxidation state intermediates (>IV) accelerating surface restructuring and metal dissolution.

Evazzade, Iman↗
DOE OSTI2025

Nature-inspired lotus-shaped fins combined with hybrid nanoparticles and metal foam for high-performance latent heat thermal energy storage

Latent heat thermal energy storage (LHTES) systems play a critical role in renewable energy integration by providing high energy density and nearly isothermal operation during phase transitions. However, their performance is often limited by slow melting/charging rates, which motivates the search for enhanced heat transfer designs. This study investigates the melting behavior of RT-82 phase change material (PCM) using novel lotus-shaped fins combined with copper metal foam and conductive graphene nanoparticles and carbon nanotubes. A two-dimensional enthalpy-porosity model in ANSYS Fluent was developed to simulate the charging/melting process, capturing non-thermal equilibrium between the foam and PCM/nano-PCM. In this study, effects of fin geometry, nanoparticle concentration, and foam porosity on melting dynamics and cost-performance trade-offs were investigated. Results showed that natural convection accelerated melting by ~12% compared to conduction-only scenarios. Optimized lotus-shaped fins with higher fin density (T3F4 and T3F10) achieved up to 63% faster melting relative to sparse configurations. Graphene nanoparticles improved thermal conductivity, with a 6% volume fraction, by reducing melting time by ~6.9%, while their combination with 75% porosity foam achieved a maximum reduction in the melting time of ~51% compared to pure PCM. Cost-performance analysis identified T3F4 as the most balanced design, offering rapid thermal response without excessive material costs, while moderate-density designs like T3S6 provided economical alternatives with acceptable performance. These results highlight the performance enhancement that can be achieved by integrating bio-inspired fins, nanoparticles, and foams, into compact and efficient LHTES for solar heating, building thermal management, and industrial waste-heat recovery applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Electro-Optic Modulation Using Metal-Free Perovskites

Electro-optic (EO) modulation is of interest to impart information onto an optical carrier. Inorganic crystals—most notably LiNbO 3 and BaTiO 3 —exhibit EO modulation and good stability, but are difficult to integrate with silicon photonic technology. Solution-processed organic EO materials are readily integrated but suffer from thermal degradation at the temperatures required in operating conditions for accelerated reliability studies. Hybrid organic–inorganic metal halide perovskites have the potential to overcome these limitations; however, these have so far relied on heavy metals such as lead and cadmium. Here, we report linear EO modulation using metal-free perovskites, which maintain the crystalline features of the inorganic EO materials and incorporate the flexible functionality of organic EO chromophores. We find that, by introducing a deficiency of cations, we reduce the symmetry in the perovskite crystal and produce thereby an increased EO response. The best-engineered perovskites reported herein showcase an EO coefficient of 14 pm V –1 at a modulation frequency of 80 kHz, an order of magnitude higher than in the nondefective materials. Furthermore, we observe split peaks in the X-ray diffraction and neutron diffraction patterns of the defective sample, indicating that the crystalline structure has been distorted and the symmetry reduced. Density functional theory (DFT) studies link this decreased symmetry to NH 4 + deficiencies. This demonstration of EO from metal-free perovskites highlights their potential in next-generation optical information transmission.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Creep deformation and cavitation in an additively manufactured Al-8.6Cu-0.4Mn-0.9Zr (wt%) alloy

Creep deformation and cavitation were investigated at 300 ºC in both tension and compression for an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr (wt%) alloy in the as-fabricated state and after various aging treatments (aging at 300 °C/200 h or 350 °C/24 h and overaging at 400 °C/200 h). Creep mechanisms at 300 °C were determined by relating the measured creep response to corresponding microstructural and X-ray computed tomography observations. In compression, alloys in the as-fabricated and two aging conditions exhibited similarly high creep resistance. Overaging (400 °C/200 h) led to substantial coarsening of intragranular θ-Al2Cu precipitates and an expected drop in their Orowan strengthening contribution. In tension, minimum strain rates comparable to those in compression were obtained at any given stress; however, upon accumulation of some plastic strain in the matrix, creep cavities started to form, leading to accelerated tertiary stage creep deformation and rupture. Cavitation occurred exclusively along melt pool boundaries due to locally enhanced diffusion enabled by (i) large grain-boundary area in adjacent fine-grained zones and (ii) localization of creep strain in nearby heat-affected zones. Although cavity growth was initially diffusion-controlled, its rate was determined by matrix creep rate, consistent with constrained cavity growth mechanisms. This study reveals how microstructural complexities induced by the additive manufacturing process affect the creep and cavitation behavior of Al-Cu-Mn-Zr alloys. The underlying creep and cavitation mechanisms uncovered in this study point to pathways that improve the high-temperature properties of additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Neural network model of the multi-mode anomalous transport module for accelerated transport simulations

Here, a neural network version of the Multi-Mode Anomalous Transport Module, known as MMMnet, has been developed to calculate plasma turbulent diffusivities in DIII-D with a calculation time suitable for control applications. MMMnet uses a simple artificial neural network structure to predict the ion thermal, electron thermal, and toroidal momentum diffusivities while reproducing Multi-Mode Model (MMM) data with good accuracy and keeping the calculation time as a fraction of that associated with MMM. Model-based control techniques require models with fast calculation times, making many existing physics-oriented predictive codes unsuitable. The control-oriented predictive code COTSIM (Control Oriented Transport SIMulator) calculates the most significant plasma dynamics in response to the different actuators while running at a speed useful for control design. In order to achieve this calculation speed, COTSIM often relies on scaling laws and control-level models. Replacing some of these scaling laws and control-level models with neural network versions of more complex physics-level models has the potential of increasing the range of validity and the level of accuracy of COTSIM without compromising its computational speed. In this work, MMMnet is integrated into COTSIM to improve the turbulent diffusivity predictions, which will in turn improve the prediction accuracy associated with the dynamics of many plasma properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

NuMI Beam Monitoring Simulation and Data Analysis Status and Progress

With the Main Injector Neutrino Oscillation Search (MINOS) experiment decommissioned, muon and hadron monitors became an important diagnostic tool for the NuMI O↵- axis vμ Appearance (NOvA) experiment at Fermilab to monitor the Neutrinos at the Main Injector (NuMI) beam. The goal of this study is to maintain the quality of the monitor signals and to establish correlations with the neutrino beam profile. And we carry out a systematic study of the response of the muon monitors to the changes in the parameters of the proton beam and lattice parameters. We report here on the progress of the beam data analysis and comparison with the simulation results.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Enabling bifacial thin film devices by developing a back surface field using Cu x AlO y

Bifacial solar cells have the potential to increase the energy yield per unit area over traditional monofacial devices without significant added cost, driving $/kWh costs lower and accelerating the adoption of solar photovoltaics. However, the performance of bifacial thin film solar cells significantly lags that achieved by crystalline silicon cells. Here we incorporate wide bandgap Cu x AlO y as a back buffer layer for CdTe devices and achieve a backside illuminated device with high current density and high fill factor. Moreover, these values remain nearly constant even as the absorber layer thickness changes, indicating that a fully-depleted device is not required for efficient charge collection. We show that this response is indicative of a back surface field, albeit with a persistent high back surface recombination velocity. By managing electron reflection, we achieved a backside illumination conversion efficiency of 7.1% and bifaciality of 0.55 for a 3.3 µm CdTe device and 8.0% and 0.62 for a 2 µm device. Future improvements can be made by identifying and incorporating a passivation material that reduces the back surface recombination velocity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Concentrating Rare Earth Elements in Coal mine drainage Using Coal Combustion Products through Abandoned Mine Land Reclamation

Rare earth elements (REEs) (including scandium, yttrium and a group of 15 lanthanides) are often considered to be critical components in the productions of renewable energy hardware, electric vehicles, health care and military equipment, and consumer electronic products. The demand of REEs has been projected to be growing at an annual rate of 5-9% in the next 25 years. In 2011, the global demand of total rare earth oxides (REOs) was estimated to be approximately 105,000 tons, which is expected to grow to 210,000 tons by 2025. China overwhelmingly dominates the current worldwide rare earth productions but has strategically restricted its exports, causing significant instability for the global market. In response to the increasing demand for REEs and the supply dominance of China, identifying alternative sources of REEs has become a critical issue for the United States and other countries. Coal, coal ash, and coal mine drainage (CMD) are considered to be the alternative sources of REEs. In the U.S., high REE concentrations have been reported to be closely associated with coal deposits, including the Appalachian Basins. When surface and/or groundwater come in contact with geologic strata containing sulfide minerals exposed by coal mining, the accelerated oxidation of sulfide minerals in the presence of ferric iron and/or oxygen can produce sulfuric acid. The process promotes the weathering of REE-bearing rocks and minerals in the host geologic strata. Compared to average river water and seawater, the concentrations of REEs can be orders of magnitude higher in CMD. In this study, we demonstrated a trap-extract-precipitate (TEP) process that can effectively recover REEs from CMD. The three-stage TEP process uses alkaline industrial by-products to capture REEs from CMD and then applies an extraction/precipitation procedure to produce a feedstock that can be economically processed to produce marketable rare earth oxides. The alkaline industrial by-products tested in this study include the residual from a water softening process (DRWP sludge) and two types of stabilized flue gas desulfurization materials (sFGDs). sFGD material is a mixture of lime (CaO) and two coal combustion by-products, calcium sulfite FGD by-product and fly ash. The objectives of this study are to (1) validate the effectiveness and feasibility; (2) determine mechanisms controlling the rare earth recovery, (3) quantify the associated economic and environmental benefits, and (4) evaluate the full-scale application. To achieve these objectives, tasks to be carried out in this proposed project are organized into three phases. In the first phase, the research team collaborated with Ohio Department of Natural Resources, American Electric Power, The Wilds (a nonprofit wildlife conservation organization), and a private landowner to carry out field investigations aimed to screen and evaluate the seasonal changes of rare earths in the CMD discharges that have high recovery potentials. Next, the recovery of REEs from CMD was tested using a series of lab-scale column and batch tests under, respectively, percolation and completely mixed conditions. Results obtained from these lab-scale studies show that all three tested solids are very effective in retaining REEs. Over 98% of the CMD REEs that contacted the solids were captured before the solids exhausted their neutralization capacities. We also determined an extraction process using a non-acid, organic ligand extraction solution that can effectively remobilize the retained REEs from the spent solids (over 90%). The REE concentrate (>7.5 wt. % of total REEs) is then formed in an aeration process. The TEP process uses environmentally benign industrial by-products and a naturally-occurring organic ligand to mitigate CMD and recover REEs. Techno-economic analysis (TEA) and life-cycle assessment (LCA) was carried out in the third phase. The engineering-economic costs and net energy, net CO2 emissions, and water and other requirements were investigated to understand the economic and environmental implications of this process. This work uses mass and energy balances from laboratory-scale experiments to estimate the economic costs and environmental impacts. The results suggest that passive treatment systems that use DRWP sludge are preferred over those that use sFGD material, because of lower economic costs ($89,300/yr with a unit cost of $86/gT-REE vs. $89,800/yr, or $278/gT-REE) and improved environmental performance across all indicators from two different impact assessment methods. These differences are largely attributable to the larger capacity of DRWP sludge in the passive treatment application. We envision this TEP process can be integrated with abandoned mine land (AML) reclamation to create an approach that can add economic incentives for AML reclamation, remediate CMD discharge, and eliminate public safety hazards and threats to local environment and ecological systems posed by AMLs. It can restore lands and communities that are adversely impacted by legacy mining.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Magnetic Field Amplification by a Plasma Cavitation Instability in Relativistic Shock Precursors

Abstract Plasma streaming instabilities play an important role in magnetic field amplification and particle acceleration in relativistic shocks and their environments. However, in the far shock precursor region where accelerated particles constitute a highly relativistic and dilute beam, streaming instabilities typically become inefficient and operate at very small scales when compared to the gyroradii of the beam particles. We report on a plasma cavitation instability that is driven by dilute relativistic beams and can increase both the magnetic field strength and coherence scale by orders of magnitude to reach near-equipartition values with the beam energy density. This instability grows after the development of the Weibel instability and is associated with the asymmetric response of background leptons and ions to the beam current. The resulting net inductive electric field drives a strong energy asymmetry between positively and negatively charged beam species. Large-scale particle-in-cell simulations are used to verify analytical predictions for the growth and saturation level of the instability and indicate that it is robust over a wide range of conditions, including those associated with pair-loaded plasmas. These results can have important implications for the magnetization and structure of shocks in gamma-ray bursts, and more generally for magnetic field amplification and asymmetric scattering of relativistic charged particles in plasma astrophysical environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Graph Neural Network-based Tracking as a Service

Recent studies have shown promising results for track finding in dense environments using Graph Neural Network (GNN)-based algorithms. However, GNN-based track finding is computationally slow on CPUs, necessitating the use of coprocessors to accelerate the inference time. Additionally, the large input graph size demands a large device memory for efficient computation, a requirement not met by all computing facilities used for particle physics experiments, particularly those lacking advanced GPUs. Furthermore, deploying the GNN-based track-finding algorithm in a production environment requires the installation of all dependent software packages, exclusively utilized by this algorithm. These computing challenges must be addressed for the successful implementation of GNN-based track-finding algorithm into production settings. In response, we introduce a ``GNN-based tracking as a service'' approach, incorporating a custom backend within the NVIDIA Triton inference server to facilitate GNN-based tracking. This paper presents the performance of this approach using the Perlmutter supercomputer at NERSC.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗