SEARCH · Engineering Papers

Results for “Visual Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1982

Computational and experimental studies of light twin aerodynamic interference

The results of an analytical and experimental study of aerodynamic interference effects for a light twin aircraft are presented. Both the influence of a body (either fuselage or nacelle) on a wing and the influence of a wing on a body are studied. The wing studied uses a new natural laminar flow airfoil with variable camber movable trailing edge. A three-dimensional panel method program utilizing surface source and surface doublet singularities was used to design wing-nacelle and wing-fuselage fairings. Experiments were conducted using a 1/6 scale reflection plane model. Forces, pressures, and surface flow visualization results are presented. Results indicate that potential flow analysis is useful to guide the design of intersection fairings, but experimental tuning is still required. While the study specifically addressed a light twin aircraft, the methods are applicable to a wide variety of aircraft.

Thomson, W. G.↗

NASA NTRS1983

Magnus effects at high angles of attack and critical Reynolds numbers

The Magnus force and moment experienced by a yawed, spinning cylinder were studied experimentally in low speed and subsonic flows at high angles of attack and critical Reynolds numbers. Flow-field visualization aided in describing a flow model that divides the Magnus phenomenon into a subcritical region, where reverse Magnus loads are experienced, and a supercritical region where these loads are not encountered. The roles of the spin rate, angle of attack, and crossflow Reynolds number in determining the boundaries of the subcritical region and the variations of the Magnus loads were studied.

Seginer, A.↗

NASA NTRS1985

A redetermination of the luminosity, distance, and reddening of Beta Lyrae

The most likely distance to the Beta Lyrae system is redetermined to lie at 370 pc, corresponding to a distance modulus of 7.8 mag, while the correct modulus value probably lies in the 7.7-8.0 mag range, corresponding to a distance range between 345 and 400 pc. On the basis of Wilson's (1974) model, the phase-averaged absolute visual magnitude of the primary component is -4.1 mag; this star is therefore a very luminous giant, classifiable as B8.5 or B9, with a luminosity class of II-Ib. The present data are based on optical and IUE scans of the brightest visual companion to Beta Lyrae, HD 174664, together with an analysis of the H line profiles in its spectrum.

Dobias, J. J.↗

NASA NTRS1986

Experimental study of effects of forebody geometry on high angle of attack static and dynamic stability

A series of low speed wind tunnel tests on a generic fighter model with a cylindrical fuselage were made to investigate the effects of forebody shape on static and dynamic lateral/directional stability. Five forebodies, including a chine nose of unconventional cross-sectional shape, were tested. Conventional force tests were conducted to determine static stability characteristics and single degree-of-freedom free-to-roll tests were used to study the wing rock susceptibility of the model with the various forebodies. Flow visualization data were obtained to aid in analysis of the complex flow phenomena involved. The results show that forebody cross-sectional shape can strongly effect both static and dynamic (roll) stability at high angles of attack. Large variations in stability were obtained for the various forebody geometries. These characteristics result from the impact of cross-sectional shape on forebody vortex development, the behavior of the vortices at sideslip conditions, and their interaction with the wing and empennage flow fields.

Brandon, J. M.↗

NASA NTRS1986

Experimental study of effects of forebody geometry on high angle of attack static and dynamic stability and control

A series of low-speed wind tunnel tests on a generic airplane model with a cylindrical fuselage were made to investigate the effects of forebody shape and fitness ratio, and fuselage/wing proximity on static and dynamic lateral/directional stability. In addition, some preliminary testing to determine the effectiveness of deflectable forebody strakes for high angle of attack yaw control was conducted. During the stability investigation, 11 forebodies were tested including three different cross-sectional shapes with fineness ratios of 2, 3, and 4. In addition, the wing was tested at two longitudinal positions to provide a substantial variation in forebody/wing proximity. Conventional force tests were conducted to determine static stability characteristics, and single-degree-of-freedom free-to-roll tests were conducted to study the wing rock characteristics of the model with the various forebodies. Flow visualization data were obtained to aid in the analysis of the complex flow phenomena involved. The results show that the forebody cross-sectional shape and fineness ratio and forebody/wing proximity can strongly affect both static and dynamic (roll) stability at high angles of attack. These characteristics result from the impact of these factors on forebody vortex development, the behavior of the vortices in sideslip, and their interaction with the wing flow field. Preliminary results from the deflectable strake investigation indicated that forebody flow control using this concept can provide very large yaw control moments at stall and post-stall angles of attack.

Brandon, J. M.↗

NASA NTRS1988

Holocinematographic Velocimeter

Holographic movies used to study turbulent flows. High-speed movie composed of single-exposure holograms of tracer particles in each of two simultaneous orthogonal views of flow. Time resolution set by movie frame rate, and total time limited by length of movie. Data from system used to verify results of theoretical models and numerical simulations of turbulence, visualize and measure coherent structures in "non-simple" turbulent flows, to examine mechanisms operative in various turbulence-control/drag-reduction concepts.

Weinstein, Leonard M.↗

NASA NTRS1988

Status of NASA/Army rotorcraft research and development piloted flight simulation

The status of the major NASA/Army capabilities in piloted rotorcraft flight simulation is reviewed. The requirements for research and development piloted simulation are addressed as well as the capabilities and technologies that are currently available or are being developed by NASA and the Army at Ames. The application of revolutionary advances (in visual scene, electronic cockpits, motion, and modelling of interactive mission environments and/or vehicle systems) to the NASA/Army facilities are also addressed. Particular attention is devoted to the major advances made in integrating these individual capabilities into fully integrated simulation environment that were or are being applied to new rotorcraft mission requirements. The specific simulators discussed are the Vertical Motion Simulator and the Crew Station Research and Development Facility.

Condon, Gregory W.↗

NASA NTRS1989

Flow-field characteristics and normal-force correlations for delta wings from Mach 2.4 to 4.6

An experimental investigation has been conducted to determine the upper-surface flowfield types and the normal-force characteristics of a series of delta wing models at supersonic speeds. Flow-visualization data were used to classify the flowfields into seven primary types: shockless attached flow, separation bubble, classical vortex, vortex with shock, shock with no separation, shock-induced separation, and separation bubble with shock. The pressure distributions were integrated to obtain upper and lower surface normal-force loadings. A minimal effect of sweep was observed on the upper-surface normal force at constant Mach number and a minimal effect of Mach number was noted for the 75 deg delta wing lower-surface normal force. The normal-force coefficients for all test conditions were correlated, and a single empirical equation was formulated from which the normal-force coefficient could be calculated as a function of Mach number, angle of attack, and wing aspect ratio.

Covell, Peter F.↗

NASA NTRS1989

Flow visualization study of grooved surface/surfactant/air sheet interaction

The effects of groove geometry, surfactants, and airflow rate have been ascertained by a flow-visualization study of grooved-surface models which addresses the possible conditions for skin friction-reduction in marine vehicles. It is found that the grooved surface geometry holds the injected bubble stream near the wall and, in some cases, results in a 'tube' of air which remains attached to the wall. It is noted that groove dimension and the use of surfactants can substantially affect the stability of this air tube; deeper grooves, surfactants with high contact angles, and angled air injection, are all found to increase the stability of the attached air tube, while convected disturbances and high shear increase interfacial instability.

Reed, Jason C.↗

NASA NTRS1991

Experimental and analytical studies of flow through a ventral and axial exhaust nozzle system for STOVL aircraft

Flow through a combined ventral and axial exhaust nozzle system was studied experimentally and analytically. The work is part of an ongoing propulsion technology effort at NASA Lewis Research Center for short takeoff, vertical landing (STOVL) aircraft. The experimental investigation was done on the NASA Lewis Powered Lift Facility. The experiment consisted of performance testing over a range of tailpipe pressure ratios from 1 to 3.2 and flow visualization. The analytical investigation consisted of modeling the same configuration and solving for the flow using the PARC3D computational fluid dynamics program. The comparison of experimental and analytical results was very good. The ventral nozzle performance coefficients obtained from both the experimental and analytical studies agreed within 1.2 percent. The net horizontal thrust of the nozzle system contained a significant reverse thrust component created by the flow overturning in the ventral duct. This component resulted in a low net horizontal thrust coefficient. The experimental and analytical studies showed very good agreement in the internal flow patterns.

Esker, Barbara S.↗

NASA NTRS1990

Visualization of the flow about a delta wing maneuvering in pitch to very high angle of attack

An experimental program of unsteady aerodynamic measurements has been carried out in one of the 7 ft by 10 ft low-speed wind tunnels at NASA Ames Research Center. Flow-visualization measurements on a delta wing model of AR = 1.0 with sharp leading edges were carried out by means of a thin planar sheet of laser light fixed in the test section at a convenient angle to the flow direction. Smoke images of the fluid motion and vortex structure above the model were recorded photographically and later analyzed to determine such information as the positions of the cores and occurrence of bursting. Large amplitude transient motion involving post stall angle of attack excursions produced significant hysteresis in the vortex burst location and was reflected in the measured aerodynamic loads.

Jarrah, M. A. M.↗

NASA NTRS1991

Experimental and analytical studies of flow through a ventral and axial exhaust nozzle system for STOVL aircraft

Esker, Barbara S.↗

NASA NTRS1992

Hypersonic aerodynamic/aerothermodynamic testing capabilities at Langley Research Center

Capabilities of the Langley Hypersonic Facilities Complex that consists of nine blowdown-to-vacuum wind tunnels are reviewed. These tunnels complement one another to provide ranges of Mach number from 6 to 20, unit Reynolds number from 0.03 to 40 million per ft, and normal shock density ratio from 2 to 12. Topics under consideration include the basic components of each facility, status, and upgrades recently performed; instrumentation and testing techniques routinely used to measure forces and moments, surface pressures, surface temperature-time histories, flow properties within the shock layer about the model via survey probes, and flow visualization; and data acquisition systems and upgrades performed via a NASA revitalization program.

Miller, C. G., III↗

NASA NTRS1994

Control of Wind Tunnel Operations Using Neural Net Interpretation of Flow Visualization Records

Neural net control of operations in a small subsonic/transonic/supersonic wind tunnel at Lewis Research Center is discussed. The tunnel and the layout for neural net control or control by other parallel processing techniques are described. The tunnel is an affordable, multiuser platform for testing instrumentation and components, as well as parallel processing and control strategies. Neural nets have already been tested on archival schlieren and holographic visualizations from this tunnel as well as recent supersonic and transonic shadowgraph. This paper discusses the performance of neural nets for interpreting shadowgraph images in connection with a recent exercise for tuning the tunnel in a subsonic/transonic cascade mode of operation. That mode was operated for performing wake surveys in connection with NASA's Advanced Subsonic Technology (AST) noise reduction program. The shadowgraph was presented to the neural nets as 60 by 60 pixel arrays. The outputs were tunnel parameters such as valve settings or tunnel state identifiers for selected tunnel operating points, conditions, or states. The neural nets were very sensitive, perhaps too sensitive, to shadowgraph pattern detail. However, the nets exhibited good immunity to variations in brightness, to noise, and to changes in contrast. The nets are fast enough so that ten or more can be combined per control operation to interpret flow visualization data, point sensor data, and model calculations. The pattern sensitivity of the nets will be utilized and tested to control wind tunnel operations at Mach 2.0 based on shock wave patterns.

Buggele, Alvin E.↗

NASA NTRS1995

CaseMIDAS - A reactive planning architecture for the man-machine integration design and analysis system

MIDAS is a set of tools which allow a designer to specify the physical and functional characteristics of a complex system such as an aircraft cockpit, and analyze the system with regard to human performance. MIDAS allows for a number of static analyses such as military standard reach and fit analysis, display legibility analysis, and vision polars. It also supports dynamic simulation of mission segments with 3d visualization. MIDAS development has incorporated several models of human planning behavior. The CaseMIDAS effort has been to provide a simplified and unified approach to modeling task selection behavior. Except for highly practiced, routine procedures, a human operator exhibits a cognitive effort while determining what step to take next in the accomplishment of mission tasks. Current versions of MIDAS do not model this effort in a consistent and inclusive manner. CaseMIDAS also attempts to address this issue. The CaseMIDAS project has yielded an easy to use software module for case creation and execution which is integrated with existing MIDAS simulation components.

Pease, R. Adam↗

NASA NTRS1996

ICASE/LaRC Symposium on Visualizing Time-Varying Data

Time-varying datasets present difficult problems for both analysis and visualization. For example, the data may be terabytes in size, distributed across mass storage systems at several sites, with time scales ranging from femtoseconds to eons. In response to these challenges, ICASE and NASA Langley Research Center, in cooperation with ACM SIGGRAPH, organized the first symposium on visualizing time-varying data. The purpose was to bring the producers of time-varying data together with visualization specialists to assess open issues in the field, present new solutions, and encourage collaborative problem-solving. These proceedings contain the peer-reviewed papers which were presented at the symposium. They cover a broad range of topics, from methods for modeling and compressing data to systems for visualizing CFD simulations and World Wide Web traffic. Because the subject matter is inherently dynamic, a paper proceedings cannot adequately convey all aspects of the work. The accompanying video proceedings provide additional context for several of the papers.

Banks, D. C.↗

NASA NTRS1996

Bubble Dynamics on a Heated Surface

In this work, we study the combined thermocapillary and natural convective flow generated by a bubble on a heated solid surface. The interaction between gas and vapor bubbles with the surrounding fluid is of interest for both space and ground-based processing. On earth, the volumetric forces are dominant, especially, in apparatuses with large volume to surface ratio. But in the reduced gravity environment of orbiting spacecraft, surface forces become more important and the effects of Marangoni convection are easily unmasked. In order to delineate the roles of the various interacting phenomena, a combined numerical-experimental approach is adopted. The temperature field is visualized using Mach-Zehnder interferometry and the flow field is observed by a laser sheet flow visualization technique. A finite element numerical model is developed which solves the two-dimensional momentum and energy equations and includes the effects of bubble surface deformation. Steady state temperature and velocity fields predicted by the finite element model are in excellent qualitative agreement with the experimental results. A parametric study of the interaction between Marangoni and natural convective flows including conditions pertinent to microgravity space experiments is presented. Numerical simulations clearly indicate that there is a considerable difference between 1-g and low-g temperature and flow fields induced by the bubble.

Kassemi, Mohammad↗

NASA NTRS1998

Preliminary In-Flight Loads Analysis of In-Line Launch Vehicles using the VLOADS 1.4 Program

To calculate structural loads of in-line launch vehicles for preliminary design, a very useful computer program is VLOADS 1.4. This software may also be used to calculate structural loads for upper stages and planetary transfer vehicles. Launch vehicle inputs such as aerodynamic coefficients, mass properties, propellants, engine thrusts, and performance data are compiled and analyzed by VLOADS to produce distributed shear loads, bending moments, axial forces, and vehicle line loads as a function of X-station along the vehicle's length. Interface loads, if any, and translational accelerations are also computed. The major strength of the software is that it enables quick turnaround analysis of structural loads for launch vehicles during the preliminary design stage of its development. This represents a significant improvement over the alternative-the time-consuming, and expensive chore of developing finite element models. VLOADS was developed as a Visual BASIC macro in a Microsoft Excel 5.0 work book on a Macintosh. VLOADS has also been implemented on a PC computer using Microsoft Excel 7.0a for Windows 95. VLOADS was developed in 1996, and the current version was released to COSMIC, NASA's Software Technology Transfer Center, in 1997. The program is a copyrighted work with all copyright vested in NASA.

Graham, J. B.↗