Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Estimated shuttle loading emissions

As space shuttle tanks are loaded with N2O4, pressurization gas is displaced and at the same time N2O4 entering the tank evaporates and mixes with the pressurization gas remaining in the tank. Further addition of N2O4 to the tank requires venting of this mixture of N2O4/NO2 vapor and pressurization gas, which must be scrubbed prior to atmospheric release. A computer analysis was performed to estimate concentrations, flow rates, and total quantities vented during the planned fast fill/slow fill cycles of 125 gallon and 640 gallon space shuttle tanks. With helium as the pressurization gas, total vent quantities were estimated to be 4.5 and 24 pounds N2O4, respectively, for the two tank sizes.

Bowman, T. E.↗

The surface of Io - Geologic units, morphology, and tectonics

The geologic units, morphology and tectonics evident on a preliminary geological map obtained from best-resolution Voyager 1 images and a preliminary pictorial map of the surface of Io are discussed. Nine volcanic units are identified on the surface which are composed of mountain materials, intervent, layered and eroded layered plains, and wall and floor, pit crater flow, shield crater flow, fissure flow and crater cone units associated with volcanic vents, along with seven types of structural features. The cumulative volcanic crater size distribution of 170 Ionian vents with craters greater than 14 km is similar to that of impact craters on other solar system bodies, with a surplus of small craters and a preponderance of volcanic vents in the Io equatorial zone. The observed surface morphologies provide evidence for a mixture of silicates and sulfur as the dominant surface material. Lineaments and grabens are also apparent on the surface, in a common planetary grid pattern.

Schaber, G. G.↗

On the geometric form of volcanoes - Comment

The model of Lacey et al. (1981) accounting for the geometric regularity and approximate cone shape of volcanoes is discussed. It is pointed out that, contrary to the model, volcano eruptions do not occur randomly in elevation and azimuth, but are commonly restricted to summit vents and a few well defined flank zones, so that the form of a volcano is determined by its vent locations and styles of eruption. Other false predictions of the model include the constancy of lava volumes at all vent elevations, the increase in volcano radius as the square root of time, a critical height for volcano growth, the influence of planetary gravity on volcano height and the negligible influence of ash falls and flows and erosional deposition. It is noted that the model of Shteynberg and Solov'yev, in which cone shape is related to stresses due to increasing cone height, may provide a better understanding of volcano morphology.

Wood, C. A.↗

Contamination Measurements During Ius Thermal Vacuum Tests in A Large Space Chamber

The levels of contamination that originate from inside the IUS equipment support section (ESS) due to outgassing from electronics components and wiring operating at elevated temperatures (80-160 F) were investigated. Pressure was measured inside and outside the ESS. Mass deposition measurements were made with quartz crystal microbalances (QCM) facing into and away from ESS vents. The OCM's were operated at -50 C and -180 C using thermoelectrically and cryogenically cooled QCM's. Gaseous nitrogen flow inside the ESS was used to obtain the effective molecular flow vent area of the ESS, which was evaluated to be 359 sq cm (56 sq in) compared to the 978 sq cm (150 sq in) estimated by an earlier atmosphere pressure billowing test. The total outgassing rate of the ESS materials at a temperature of 60 C (140 F) decays with a time constant of 11.5 hours based on pressure measurements during the hot cycle. A time constant of 22 hours was estimated for the fraction of the outgassing which will condense on a -50 C surface. In contrast, the time constant is only 10.1 hours for the outgassing material which condenses on a surface at -180 C. A surface at -180 C collects approximately one half of the material vented from the ESS which impinges on it. Pressure measurements show very good correlation with the mass deposition measurements.

C R Mullen↗

Review of NASA ACLS research

An experimental investigation was conducted to evaluate a method of maintaining stability of an air cushion vehicle and also to evaluate several concepts to brake and steer an ACLS-equipped vehicle. The investigation used a modified airboat equipped with an air cushion landing system. The pressure relief door stability concept was characterized by the ACLS pressure time histories. The pressure relief doors vented excess cavity and lobe pressures and consistently maintained vehicle heave and pitch stability. Braking concepts were characterized by the average deceleration of the vehicle. Reduced lobe flow and cavity venting braking concepts were evaluated in this program. The cavity venting concept demonstrated the best performance, producing decelerations on the test vehicle on the same order as moderate braking with conventional wheel brakes. Steering concepts were evaluated by recording the path taken while attempting to follow a prescribed maneuver. The steering concepts evaluated included using rudders only, using differential lobe flow, and using rudders combined with a lightly loaded, nonsteering center wheel. The latter concept proved to be the most accurate means of steering the vehicle on the ACLS, producing translational deviations which, while two to three times higher than those from conventional nose gear steering, were still felt to provide reasonably precise steering control for this type vehicle.

Daugherty, R. H.↗

Radar Observations of Fissure-fed Basaltic Lava Flows, Craters of the Moon, Idaho

Changes in surface roughness of lava flows, estimated from dual polarization, synthetic aperture, X and L band side-looking airborne radar images, were tested as a means of locating fissure vent areas. If lava textures proess from smooth, near-vent shelly pahoehoe to hummocky pahoehoe to aa with distance from fissure vents, then radr images of the lava flows would show a progression from dark to brighter tones due to the flows' increasing radar back-scatter.

Martel, L.↗

Mixing-induced fluid destratification and ullage condensation

In many applications, on-orbit storage and transfer of cryogens will require forced mixing to control tank pressure without direct venting to space. During a no-vent transfer or during operation of a thermodynamic vent system in a cryogen storage tank, pressure control is achieved by circulating cool liquid to the liquid-vapor interface to condense some of the ullage vapor. To measure the pressure and temperature response rates in mixing-induced condensation, an experiment has been developed using Freon 11 to simulate the two-phase behavior of a cryogen. A thin layer at the liquid surface is heated to raise the tank pressure, and then a jet mixer is turned on to circulate the liquid, cool the surface, and reduce the pressure. Many nozzle configurations and flow rates are used. Tank pressure and the temperature profiles in the ullage and the liquid are measured. Initial data from this ground test are shown correlated with normal-gravity and drop-tower dye-mixing data. Pressure collapse times are comparable to the dye-mixing times, whereas the times needed for complete thermal mixing are much longer than the dye-mixing times.

Meserole, Jere S.↗

The geology of Pine and Crater Buttes: Two basaltic constructs on the far eastern Snake River Plain

The emplacement history and petrochemical evolution of the volcanics associated with Pine Butte, Crater Butte, and other nearby vents are developed and described. Four major vents were identified in the study area and their associated eruptive products were mapped. All of the vents show a marked physical elongation or linear orientation coincident with the observed rift set. Planetary exploration has revealed the importance of volcanic processes in the genesis and modification of extraterrestrial surfaces. Interpretation of surface features has identified plains-type basaltic volcanism in various mare regions of the Moon and the volcanic provinces of Mars. Identification of these areas with features that appear analogous to those observed in the Pine Butte area suggests similar styles of eruption and mode of emplacement. Such terrestrial analogies serve as a method to interpret the evolution of volcanic planetary surfaces on the inner planets.

Mazierski, Paul F.↗

An analysis of bipropellant neutralization for spacecraft refueling operations

Refueling of satellites on orbit with storable propellants will involve venting part or all of the pressurant gas from the propellant tanks. This gas will be saturated with propellant vapor, and it may also have significant amounts of entrained fine droplets of propellant. The two most commonly used bipropellants, monomethyl hydrazine (MMH) and nitrogen tetroxide (N2O4), are highly reactive and toxic. Various possible ways of neutralizing the vented propellants are examined. The amount of propellant vented in a typical refueling operation is shown to be in the range of 0.2 to 5% of the tank capacity. Four potential neutralization schemes are examined: chemical decomposition, chemical reaction, condensation and adsorption. Chemical decomposition to essentially inert materials is thermodynamically feasible for both MMH and N2O4. It would be the simplest and easiest neutralization method to implement. Chemical decomposition would require more complex control. Condensation would require a refrigeration system and a very efficent phase separator. Adsorption is likely to be much heavier. A preliminary assessment of the four neutralization shemes is presented, along with suggested research and development plans.

Kauffman, David↗

Lava fountain heights at Pu'u 'O'o, Kilauea, Hawaii - Indicators of amount and variations of exsolved magma volatiles

Factors most important in determining fountain height in Hawaiian-type basaltic eruptions were assessed on the basis of theoretical calculations and observations at Pu'u 'O'o vent, east rift zone of Kilauea, Hawaii. It is shown that fountain height is very sensitive to changes in exsolved gas content (and, thus, can be used to estimate variability in exsolved gas content) and relatively insensitive to large variations in volume flux. Volume flux was found to be the most important parameter determining the equilibrium vent diameter. The results of calculations also indicate that there was a general increase in magma gas content over the first 20 episodes of the Pu'u 'O'o eruption and that gas depletion took place in the conduit beneath the vent during repose periods.

Head, James W., III↗

Reducing Thrusts In Solid-Fuel Rockets

Thrust-terminating system conceived to reduce thrust of solid-propellant rocket motor in controlled manner such that thrust loads not increased or decreased beyond predictable levels. Concept involves explosively cutting opposing venting pairs in case of rocket motor above nozzles to initiate venting of chamber and reduction of thrust. Vents sized and numbered to control amount and rate of reduction in thrust.

Bement, Laurence J.↗

Joint JSC/GSFC two-TDRS navigation certification results for STS-29, STS-30, and STS-32

The procedures used and the results obtained in the joint Johnson Space Center (JSC)/Goddard Space Flight Center (GSFC) navigation certification of the two-Tracking and Data Relay Satellite (TDRS) S-band tracking configuration for support of low- to medium-inclination (28.5 to 62 degrees) Shuttle missions (STS-29 and STS-30) and Shuttle rendezvous missions (STS-32) are described. The objective of this certification effort was to certify the two-TDRS configuration for nominal Space Transportation System (STS) on-orbit navigation support, thereby making it possible to significantly reduce the ground tracking support requirements for routine STS on-orbit navigation. JSC had the primary responsibility for certification of the two-TDRS configuration for STS support, and GSFC supported the effort by performing Ground Network (GN) and Space Network (SN) tracking data evaluation, parallel orbit solutions, and solution comparisons. In the certification process, two types of orbit determination solutions were generated by JSC and by GSFC for each tracking arc evaluated, one type using TDRS-East and TDRS-West tracking data combined with ground tracking data (the reference solutions) and one type using only TDRS-East and TDRS-West tracking data. The two types of solutions were then compared to determine the maximum position differences over the solution arcs and whether these differences satisfied the navigation certification criteria. The certification criteria were a function of the type of Shuttle activity in the tracking arc, i.e., quiet, moderate, or active. Quiet periods included no attitude maneuvers or ventings; moderate periods included one or two maneuvers or ventings; and active periods included more than two maneuvers or ventings. The results of the individual JSC and GSFC certification analyses for the STS-29, STS-30, and STS-32 missions and the joint JSC/GSFC conclusions regarding certification of the two-TDRS S-band configuration for STS support are presented.

Schmidt, Thomas G.↗

Review and test of chilldown methods for space-based cryogenic tanks

The literature for tank chilldown methods applicable to cryogenic tankage in the zero gravity environment of earth orbit is reviewed. One method is selected for demonstration in a ground based test. The method selected for investigation was the charge-hold-vent method which uses repeated injection of liquid slugs, followed by a hold to allow complete vaporization of the liquid and a vent of the tank to space vacuum to cool tankage to the desired temperature. The test was conducted on a 175 cubic foot, 2219 aluminum walled tank weighing 329 pounds, which was previously outfitted with spray systems to test nonvented fill technologies. To minimize hardware changes, a simple control-by-pressure scheme was implemented to control injected liquid quantities. The tank cooled from 440 R sufficiently in six charge-hold-vent cycles to allow a complete nonvented fill of the test tank. Liquid hydrogen consumed in the process is estimated at 32 pounds.

Chato, David J.↗

Clast sizes in terrestrial and Martian ignimbrite lag deposits

A theoretical model for predicting the sizes of clasts which may be expected in proximal ignimbrite deposits on the earth and Mars is developed. The model can provide an explanation of the eruption mechanism. It takes into account the inside and outside conditions of a vent from which a large-scale pyroclastic flow takes place. The drag forces exerted by the dusty gas on relatively large clasts are also taken into account. The sizes of the largest clasts that contribute to a proximal lag breccia deposit can thus be deduced. The analysis has shown that the pressure at the surface vent level in an ignimbrite-forming eruption is independent of the planetary atmospheric pressure; the gravity and vent size then become the major factors controlling the size of the largest clast which can be erupted.

Wilson, Lionel↗

Review and test of chilldown methods for space-based cryogenic tanks

The literature for tank chilldown methods applicable to cryogenic tankage in the zero gravity environment of earth orbit is reviewed. One method is selected for demonstration in a ground based test. The method selected for investigation was the charge-hold-vent method which uses repeated injection of liquid slugs, followed by a hold to allow complete vaporization of the liquid and a vent of the tank to space vacuum to cool tankage to the desired temperature. The test was conducted on a 175 cubic foot, 2219 aluminum walled tank weighing 329 pounds, which was previously outfitted with spray systems to test nonvented fill technologies. To minimize hardware changes, a simple control-by-pressure scheme was implemented to control injected liquid quantities. The tank cooled from 440 R sufficiently in six charge-hold-vent cycles to allow a complete nonvented fill of the test tank. Liquid hydrogen consumed in the process is estimated at 32 pounds.

Chato, David J.↗

Analysis of a space emergency ammonia dump using the FLOW-NET two-phase flow program

Venting of cryogenic and non-cryogenic fluids to a vacuum or a very low pressure will take place in many space-based systems that are currently being designed. This may cause liquid freezing either internally within the flow circuit or on external spacecraft surfaces. Typical ammonia flow circuits were investigated to determine the effect of the geometric configuration and initial temperature, pressure, and void fraction on the freezing characteristics of the system. The analysis was conducted also to investigate the ranges of applicability of the FLOW-NET program. It was shown that a typical system can be vented to very low liquid fractions before freezing occurs. However, very small restrictions in the flow circuit can hasten the inception of freezing. The FLOW-NET program provided solutions over broad ranges of system conditions, such as venting of an ammonia tank, initially completely filled with liquid, through a series of contracting and expanding line cross sections to near-vacuum conditions.

Navickas, J.↗

Impact contribution of prebiotic reactants to Earth

A study was performed to explore the effectiveness of comets for chemical evolution. The concentration of amino acids in various terrestrial environments was mathematically explored as there is evidence that amino acids formed as a result of cometary impact. First, the initial concentration of amino acids in surface environment after cometary impact was estimated. The effect of hydrothermal vents, ultra-violet rays, and clays was taken into consideration. Next, the absorption of amino acids by clay particles before degradation by ultra-violet light was analyzed. Finally, the effectiveness of clays, ultra-violet, and hydrothermal vents as sinks for cometary amino acids was compared. A mathematical model was then developed for the production of impact deposits on Earth for the past 2 Ga, and the relative thickness distribution was computed for impact deposits produced in 2 Ga. The reported relative thickness distribution of tillites and diamicites of all ages agrees with the thickness calculated from this impact model. This suggests that many of the ancient tillites and diamicites could be of impact origin. The effectiveness of comets was explored on the chemical evolution of amino acids. The effect of sinks such as clays, submarine vents, and UV light on amino acid concentration was considered. Sites favorable to chemical evolution of amino acids were examined, and it was concluded that chemical evolution could have occurred at or above the surface even during periods of intense bombardment of the Earth more than 3.8 billion years ago.

Aggarwal, Hans R.↗

Water cooling system for an air-breathing hypersonic test vehicle

This study provides concepts for hypersonic experimental scramjet test vehicles which have low cost and low risk. Cryogenic hydrogen is used as the fuel and coolant. Secondary water cooling systems were designed. Three concepts are shown: an all hydrogen cooling system, a secondary open loop water cooled system, and a secondary closed loop water cooled system. The open loop concept uses high pressure helium (15,000 psi) to drive water through the cooling system while maintaining the pressure in the water tank. The water flows through the turbine side of the turbopump to pump hydrogen fuel. The water is then allowed to vent. In the closed loop concept high pressure, room temperature, compressed liquid water is circulated. In flight water pressure is limited to 6000 psi by venting some of the water. Water is circulated through cooling channels via an ejector which uses high pressure gas to drive a water jet. The cooling systems are presented along with finite difference steady-state and transient analysis results. The results from this study indicate that water used as a secondary coolant can be designed to increase experimental test time, produce minimum venting of fluid and reduce overall development cost.

Petley, Dennis H.↗