Results for “Transient sources” — Page 36

NASA NTRS2003

Transient Modeling of Hybrid Rocket Low Frequency Instabilities

A comprehensive dynamic model of a hybrid rocket has been developed in order to understand and predict the transient behavior including instabilities. A linearized version of the transient model predicted the low-frequency chamber pressure oscillations that are commonly observed in hybrids. The source of the instabilities is based on a complex coupling of thermal transients in the solid fuel, wall heat transfer blocking due to fuel regression rate and the transients in the boundary layer that forms on the fuel surface. The oscillation frequencies predicted by the linearized theory are in very good agreement with 43 motor test results obtained from the hybrid propulsion literature. The motor test results used in the comparison cover a very wide spectrum of parameters including: 1) four separate research and development programs, 2) three different oxidizers (LOX, GOX, N2O), 3) a wide range of motor dimensions (i.e. from 5 inch diameter to 72 inch diameter) and operating conditions and 4) several fuel formulations. A simple universal scaling formula for the frequency of the primary oscillation mode is suggested.

Karabeyoglu, M. Arif↗

NASA NTRS1984

Transient flow combustion

Non-steady combustion problems can result from engine sources such as accelerations, decelerations, nozzle adjustments, augmentor ignition, and air perturbations into and out of the compressor. Also non-steady combustion can be generated internally from combustion instability or self-induced oscillations. A premixed-prevaporized combustor would be particularly sensitive to flow transients because of its susceptability to flashback-autoignition and blowout. An experimental program, the Transient Flow Combustion Study is in progress to study the effects of air and fuel flow transients on a premixed-prevaporized combustor. Preliminary tests performed at an inlet air temperature of 600 K, a reference velocity of 30 m/s, and a pressure of 700 kPa. The airflow was reduced to 1/3 of its original value in a 40 ms ramp before flashback occurred. Ramping the airflow up has shown that blowout is more sensitive than flashback to flow transients. Blowout occurred with a 25 percent increase in airflow (at a constant fuel-air ratio) in a 20 ms ramp. Combustion resonance was found at some conditions and may be important in determining the effects of flow transients.

Tacina, R. R.↗

NASA NTRS2002

Characteristics of Transients in the Galactic Bulge

Biweekly X-ray observations of the Galactic Bulge with the Rossi X-Ray Timing Explorer Proportional Counter Array for 5 years have built up statistics for different kinds of source behavior for low-mass binaries with neutron stars. The relation between the characteristic behaviors is not known. A typical transient may rise fast and decay exponentially in brightness and repeat this cycle after short (1/2 yr) or long intervals (20 yr). But an X-ray source also may be steady for an extended period (years) before the disk can become quiescent. It fades in the same way as do the transients which immediately decay. These sources have been reported to be very cool in quiescence; either not substantially heated by outbursts, or cooled very quickly. There are 3 sources active during the last 5 years which were long lasting transients which turned off and 1 which turned on. We will compare their X-ray characteristics in outburst, and in so far as available with Chandra, in quiescence.

Swank, Jean H.↗

NASA NTRS1999

The Bright Gamma-Ray Transient GRO J1838-0145: Multiwavelength Studies of X-Ray Novae

We completed the observational work regarding the bright gamma-ray transient GRO J1838-014 that might be a representative of a new class of gamma-ray sources in our Galaxy. A bright gamma-ray flare was detected by EGRET in June 1996. Its time variability (approx. weeks) and the absence of a clearly identified radio-loud (-approx. 1 Jy) blazar in its error box are crucial for our interpretation of GRO J1838-014 as an object different from gamma-ray blazars or isolated pulsars. We also observed the error box with ASCA and SAX pointings without identifying obvious candidate counterparts. The X-ray flux in quiescence, if any, is quite low, and canonical X-ray binary systems are also excluded. GRO J1838-014 is not the only non-blazar gamma-ray transients detected by EGRET in the Galactic plane. An analysis of CGRO Cycle 4 data is being completed in collaboration with R. Mukherjee and J. Mattox with the discussion of other interesting unidentified sources. Pulsars embedded in transient gaseous surroundings (maybe in binary systems) or compact objects in special systems are plausible candidates. A theoretical analysis is being developed. We also continued the study of Galactic X-ray novae, in particular of systems producing radio jets such as GRS 1915+10. The use of Green Bank Interferometer data (of which the MT is the chair of the executive committee) has been of great use to GRO and other satellite missions. We completed a study of X-ray/radio outbursts of GRS 1915+10 with BSAX and Ryle radiotelescope data and CGRO/BATSE simultaneous data. We also continued our theoretical work on gamma-ray bursts.

Tavani, Marco↗

NASA NTRSDate not supplied

Validation of Transient Spacecraft Refueling Model with Gateway Breadboard Test Data

The ability to refuel spacecraft on-orbit is a key enabling technology for deep space human exploration. On-orbit refueling requires priming a pressurized liquid propellant from a source tank into fluid transfer lines at vacuum conditions, which could result in excessive surge pressures beyond the system’s qualified operating limits and potentially damage hardware. Another source of potentially damaging surge pressures is the water hammer transient that occurs when the isolation valves are closed to pause or end the refueling operation. Therefore, it is imperative to employ numerical models during the development of flight hardware to parametrically characterize system performance over a wide range of operating conditions to minimize the risk of exceeding pressure limits during flight. Since rapid pressure transients can be difficult to model accurately, it is important to validate those models with test data. As part of the Gateway bipropellant refueling system development, a simplified fluidic breadboard system was created using water as a simulant for fuel to support early program risk reduction of refueling operations. The objectives of breadboard testing were to gather performance data to characterize and demonstrate critical refueling operations and to validate numerical models that can be extended to predicting flight system performance. A description of the breadboard test article and the results of numerical model validation is presented. The model is shown to have very good agreement with test data.

Refueling↗

NASA NTRS1980

A probable 1970 hard X-ray outburst by 4U0041+32

Balloon observations of a hard X-ray burst in 1970 most likely associated with the highly variable high-latitude X-ray source 4U 0041+32 are reported. The observation of X-ray flux at a density of about 0.06 photons/sq cm per sec from a previously unknown source at r.a. O h 45 min, dec 33 + or - 3 deg was made by a scintillation telescope on February 4, 1970. The spectrum was found to be very hard between 25 and 300 keV, with radiation in the form of a well-collimated beam causing the excess counting rate over a period of 30 min. Further observations on September 25, 1970 indicated the object had faded to an intensity below 0.01 photons/sq cm per sec. The power law spectrum obtained during the February burst is observed to differ from those of other hard transients and hard compact binary X-ray sources by the fact that it extends to 300 keV, its apparent lack of pulsation and its not being associated with an early-type giant or supergiant companion.

Laros, J. G.↗

NASA NTRS2006

The Swift-BAT Hard X-ray Transient Monitor

The Burst Alert Telescope (BAT) on the Swift satellite is a large field of view instrument that continually monitors the sky to provide the gamma-ray burst trigger for Swift. An average of more than 70% of the sky is observed on a daily basis. The survey mode data is processed on two sets on time scales: from one minute to one day as part of the transient monitor program, and from one spacecraft pointing (approx.20 minutes) to the full mission duration for the hard X-ray survey program. The transient monitor has recently become public through the web site http:// swift.gsfc.nasa.gov/docs/swift/results/transients/. Sky images are processed to detect astrophysical sources in the 15-50 keV energy band and the detected flux or upper limit is calculated for >100 sources on time scales up to one day. Light curves are updated each time that new BAT data becomes available (approx.10 times daily). In addition, the monitor is sensitive to an outburst from a new or unknown source. Sensitivity as a function of time scale for catalog and unknown sources will be presented. The daily exposure for a typical source is approx.1500-3000 seconds, with a 1-sigma sensitivity of approx.4 mCrab. 90% of the sources are sampled at least every 16 days, but many sources are sampled daily. It is expected that the Swift-BAT transient monitor will become an important resource for the high energy astrophysics community.

Krimm, Hans↗

NASA NTRS1986

Wave propagation in anisotropic medium due to an oscillatory point source with application to unidirectional composites

The far-field displacements in an infinite transversely isotropic elastic medium subjected to an oscillatory concentrated force are derived. The concepts of velocity surface, slowness surface and wave surface are used to describe the geometry of the wave propagation process. It is shown that the decay of the wave amplitudes depends not only on the distance from the source (as in isotropic media) but also depends on the direction of the point of interest from the source. As an example, the displacement field is computed for a laboratory fabricated unidirectional fiberglass epoxy composite. The solution for the displacements is expressed as an amplitude distribution and is presented in polar diagrams. This analysis has potential usefulness in the acoustic emission (AE) and ultrasonic nondestructive evaluation of composite materials. For example, the transient localized disturbances which are generally associated with AE sources can be modeled via this analysis. In which case, knowledge of the displacement field which arrives at a receiving transducer allows inferences regarding the strength and orientation of the source, and consequently perhaps the degree of damage within the composite.

Williams, J. H., Jr.↗

NASA NTRS2004

Baseline Testing of Ultracapacitors for the Next Generation Launch Technology (NGLT) Project

The NASA John H. Glenn Research Center initiated baseline testing of ultracapacitors for the Next Generation Launch Transportation (NGLT) project to obtain empirical data for determining the feasibility of using ultracapacitors for the project. There are large transient loads associated with NGLT that require either a very large primary energy source or an energy storage system. The primary power source used for these tests is a proton exchange membrane (PEM) fuel cell. The energy storage system can consist of devices such as batteries, flywheels, or ultracapacitors. Ultracapacitors were used for these tests. Ultracapacitors are ideal for applications such as NGLT where long life, maintenance-free operation, and excellent low-temperature performance is essential. State-of-the-art symmetric ultracapacitors were used for these tests. The ultracapacitors were interconnected in an innovative configuration to minimize interconnection impedance. PEM fuel cells provide excellent energy density, but not good power density. Ultracapacitors provide excellent power density, but not good energy density. The combination of PEM fuel cells and ultracapacitors provides a power source with excellent energy density and power density. The life of PEM fuel cells is shortened significantly by large transient loads. Ultracapacitors used in conjunction with PEM fuel cells reduce the transient loads applied to the fuel cell, and thus appreciably improves its life. PEM fuel cells were tested with and without ultracapacitors, to determine the benefits of ultracapacitors. The report concludes that the implementation of symmetric ultracapacitors in the NGLT power system can provide significant improvements in power system performance and reliability.

Eichenberg, Dennis J.↗

NASA NTRS2005

Baseline Testing of Ultracapacitors for the Next Generation Launch Technology (NGLT) Project

The NASA John H. Glenn Research Center initiated baseline testing of ultracapacitors for the Next Generation Launch Transportation (NGLT) project to obtain empirical data for determining the feasibility of using ultracapacitors for the project. There are large transient loads associated with NGLT that require either a very large primary energy source or an energy storage system. The primary power source used for these tests is a proton exchange membrane (PEM) fuel cell. The energy storage system can consist of devices such as batteries, flywheels, or ultracapacitors. Ultracapacitors were used for these tests. Ultracapacitors are ideal for applications such as NGLT where long life, maintenance-free operation, and excellent low-temperature performance is essential. State-of-the-art symmetric ultracapacitors were used for these tests. The ultracapacitors were interconnected in an innovative configuration to minimize interconnection impedance. PEM fuel cells provide excellent energy density, but not good power density. Ultracapacitors provide excellent power density, but not good energy density. The combination of PEM fuel cells and ultracapacitors provides a power source with excellent energy density and power density. The life of PEM fuel cells is shortened significantly by large transient loads. Ultracapacitors used in conjunction with PEM fuel cells reduce the transient loads applied to the fuel cell, and thus appreciably improves its life. PEM fuel cells were tested with and without ultracapacitors, to determine the benefits of ultracapacitors. The report concludes that the implementation of symmetric ultracapacitors in the NGLT power system can provide significant improvements in power system performance and reliability.

Eichenberg, Dennis J.↗

NASA NTRS1982

Persistent X-ray emission from a gamma-ray burst source

A quiescent X-ray source detected with the Einstein X-ray Observatory in a location consistent with that of an intense gamma ray burst is shown to be also consistent with the location of the 1928 optical transient, the likely optical counterpart of the gamma ray burst source GBS0117-29. The system appears to be underluminous in X-rays by a factor of 10; possible reasons for this are discussed. The observed X-ray flux would require an accretion rate of about 10 to the -14th (d/1 kpc/)-squared solar masses per year, which is probably too low to be consistent with published nuclear flash models for gamma bursts, unless the distance is substantially greater than about 1 kpc or the burst recurrence time is greater than about 50 yrs, or the accretion rate is highly variable. Such a long recurrence time appears to be inconsistent with the detection of the optical burst.

Grindlay, J. E.↗

NASA NTRS1971

Voltage-programed control of turboalternator load

A power source and load-control concept was designed and tested for use with a Brayton cycle turboalternator. The concept provides power that adjusts to a range of loads while controlling alternator speed and isolating load-switching transients. The concept is also applicable to power-generating sources other than the Brayton cycle.

Young, R. N.↗

NASA NTRSDate not supplied

On Predicting Transient Pressure in Vacuum Systems Featuring Getter Materials

Getter materials have been used to reduce pressure or partial pressures in a variety of vacuum applications ranging from vacuum tubes to space flight science instruments. Testing of getter materials has tended to emphasize the capacity of candidate materials to collect specific gas species in sufficient quantities to size them in these applications. When determining a getter material’s capacity, it is typically subjected to enough excess target gas to ensure it sorbs as quickly as possible. However, when both the gas source strength and the getter’s sorption rate exhibit transient decay behavior, such data is not sufficient to predict the targeted species’ partial pressure within a vacuum system as a function of time.

M. S. Woronowicz↗

NASA NTRSDate not supplied

On Predicting Transient Pressure in Vacuum Systems Featuring Getter Materials

Getter materials have been used to reduce pressure or partial pressures in a variety of vacuum applications ranging from vacuum tubes to space flight science instruments. Testing of getter materials has tended to emphasize the capacity of candidate materials to collect specific gas species in sufficient quantities to size them in these applications. When determining a getter material’s capacity, it is typically subjected to enough excess target gas to ensure it sorbs as quickly as possible. However, when both the gas source strength and the getter’s sorption rate exhibit transient decay behavior, such data is not sufficient to predict the targeted species’ partial pressure within a vacuum system as a function of time.

M. S. Woronowicz↗

NASA NTRSDate not supplied

On Predicting Transient Pressure in Vacuum Systems Featuring Getter Materials

Getter materials have been used to reduce pressure or partial pressures in a variety of vacuum applications ranging from vacuum tubes to space flight science instruments. Testing of getter materials has tended to emphasize the capacity of candidate materials to collect specific gas species in sufficient quantities to size them in these applications. When determining a getter material’s capacity, it is typically subjected to enough excess target gas to ensure it sorbs as quickly as possible. However, when both the gas source strength and the getter’s sorption rate exhibit transient decay behavior, such data is not sufficient to predict the targeted species’ partial pressure within a vacuum system as a function of time.

Michael Woronowicz↗

NASA NTRS2011

All-Sky Monitoring of Variable Sources with Fermi GBM

Using the Gamma ray Burst Monitor (GBM) on Fermi, we monitor the transient hard X-ray/soft gamma ray sky. The twelve GBM NaI detectors span 8 keV to 1 MeV, while the two BGO detectors span 150 keV to 40 MeV. We use the Earth occultation technique to monitor a number of sources, including X-ray binaries, AGN, and solar flaring activity. Our monitoring reveals predictable and unpredictable phenomena such as transient outbursts and state changes. With GBM we also track the pulsed flux and spin frequency of accretion powered pulsars using epoch-folding techniques. Searches for quasi-periodic oscillations and X-ray bursts are also possible with GBM all-sky monitoring. Highlights from the Earth Occultation and Pulsar projects will be presented including our recent surprising discovery of variations in the total flux from the Crab. Inclusion of an all-sky monitor is crucial for a successful future X-ray timing mission.

Wilson-Hodge, Colleen A.↗

NASA NTRS1986

Some energy considerations in gamma ray burst location determinations by an anisotropic array of detectors

The anisotropic array of detectors to be used in the Burst and Transient Experiment (BATSE) for locating gamma ray burst sources is examined with respect to its ability to locate those sources by means of the relative response of its eight detectors. It was shown that the energy-dependent attenuation effects of the aluminum window covering each detector has a significant effect on source location determinations. Location formulas were derived as a function of detector counts and gamma ray energies in the range 50 to 150 keV. Deviation formulas were derived and serve to indicate the location error that would be cuased by ignoring the influence of the passive absorber.

Young, J. H.↗

NASA NTRS1987

Latitudinal dependence of solar wind speed

The data of King (1979, 1983) and of Hoeksema et al. (1982, 1983) are used to investigate the solar-cycle evolution of solar wind bulk speed as a function of source magnetic field strength. The effects of solar transient events are removed. The data suggest that the latitudinal gradient in background solar wind speed is steepest at solar minimum and broadest at solar maximum. The lowest and highest background speeds are found to remain fairly constant throughout the solar cycle. A function developed for the background solar wind speed is inserted into the improved kinematic code of Hakamada and Akasofu (1982), and solar wind speed and IMF are simulated for two periods in the solar cycle. The observed parameters for specific coronal hole passage are well reproduced by the analysis.

Fry, C. D.↗