SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Preliminary investigation of inlet ingestion of a wing tip vortex

An inlet-coldpipe assembly was placed in a Mach 0.4 stream to ingest the tip vortex of a forward mounted wing. The strongest vortex was produced by a wing angle of attack of 11 degrees. The vortex displayed a tangential velocity of 57 percent of local stream velocity prior to entering the inlet, and a tangential velocity of 25 percent of local velocity at the simulated compressor-face. The total-pressure profiles measured by standard compressor-face rakes were changed by the presence of the vortex only at the highest tested inlet mass-flow ratios.

Mitchell, G. A.↗

NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 ft/sec). The stages were tested statically in a 15-inch-diameter model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 ft/sec and 900 ft/sec stages. For the 1050 ft/sec stage, the design-speed forward-radiated power level was about 7 db higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗

NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan: Tabulation and plots of test data

Noise and wake structure measurements in a ducted fan were conducted. The tip speed was kept at subsonic levels. The anechoic platform used during the test is described. The following conditions are reported: (1) one third octave band analyses of the fan noise data, (2) narrow band analyses of the fan noise for selected test conditions, (3) narrow band sound power level data for all fan test conditions, and (4) velocity and air angle evaluation of blade wake data.

Magliozzi, B.↗

NASA NTRS1973

Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

The technology of impregnated materials is described and some inherently advantageous characteristics of impregnated cathodes are discussed. Thermionic emission measurements are presented for oxide coated and impregnated cathodes. Five cathode configurations with barium oxide impregnated porous tungsten inserts and/or tips have been fabricated and tested. Reliability, durability, and stability of operation are characterized. One of the cathodes has accumulated over 9000 operational hours, another has been cycled on and off more than 800 times.

Hudson, W. R.↗

NASA NTRS1973

High tip speed fan inlet noise reduction using treated inlet splitters and accelerating inlets (quiet engine program fan C scale model)

A series of inlet suppression tests were run on a supersonic tip speed fan which employed an acoustically treated cowl wall, treated splitters and elevated average throat Mach numbers in various combinations. Results show appreciable fan noise reductions at high fan speeds; 15-18 PNdB. On the basis of inlet total pressure recovery loss per PNdb of noise reduction, an inlet with no splitters produced the most efficient design. However, greater reduction in noise was achieved with one splitter in the inlet. It was also noted that moderate increases in inlet Mach number increased noise in the acoustically treated inlets and that Mach numbers in excess of 0.65 were required before net noise reduction was realized.

Kazin, S. B.↗

NASA NTRS1973

Experimental investigation of model variable-geometry and ogee tip rotors.

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that several variable-geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance.

Landgrebe, A. J.↗

NASA NTRS1973

Performance of a single-stage transonic compressor with a blade-tip solidity of 1.5 and comparison with 1.3 and 1.7 solidity stages

The overall and blade-element performance of a transonic compressor stage with a tip solidity of 1.5 is presented over the stable operating range at rotative speeds from 50 to 100 percent of design speed. State peak efficiency of 0.82 was obtained at a weight flow of 29.4 kg.sec (200.4 (kg/sec)/m2 of annulus area) and a pressure ratio of 1.71. Stall margin at design speed was 14 percent. A comparison of three stages in a solidity study showed that the performance of the 1.5 solidity stage and the 1.3 solidity stage were nearly identical but that the performance of the 1.7 solidity stage was significantly lower.

Osborn, W. M.↗

NASA NTRS1973

Acoustic testing of a 1.5 pressure ratio low tip speed fan with a serrated rotor (QEP fan B scale model)

A scale model of the bypass flow region of a 1.5 pressure ratio, single stage, low tip speed fan was tested with a serrated rotor leading edge to determine its effects on noise generation. The serrated rotor was produced by cutting teeth into the leading edge of the nominal rotor blades. The effects of speed and exhaust nozzle area on the scale models noise characteristics were investigated with both the nominal rotor and serrated rotor. Acoustic results indicate the serrations reduced front quadrant PNL's at takeoff power. In particular, the 200 foot (61.0 m) sideline noise was reduced from 3 to 4 PNdb at 40 deg for nominal and large nozzle operation. However, the rear quadrant maximum sideline PNL's were increased 1.5 to 3 PNdb at approach thust and up to 2 PNdb at takeoff thust with these serrated rotor blades. The configuration with the serrated rotor produced the lowest maximum 200 foot (61.0 m) sideline PNL for any given thust when the large nozzle (116% of design area) was employed.

Kazin, S. B.↗

NASA NTRS1974

Performance of a 1.15-pressure-ratio axial-flow fan stage with a blade tip solidity of 0.5

The overall and blade-element performance of a low-solidity, low-pressure-ratio, low-tip-speed fan stage is presented over the stable operating range at rotative speeds from 90 to 120 percent of design speed. At design speed a stage peak efficiency of 0.836 was obtained at a weight flow of 30.27 kilograms per second and a pressure ratio of 1.111. The pressure ratio was less than design pressure ratio, and the design energy input into the rotor was not achieved. A mismatch of the rotor and stator blade elements resulted due to the lower than design pressure ratio of the rotor.

Osborn, W. M.↗

NASA NTRS1974

Acoustic results of supersonic tip speed fan blade modification

A supersonic tip speed single stage fan was modified with the intent of reducing multiple pure tone (MPT) or buzz saw noise. There were three modifications to the blades from the original design. The modifications to the blade resulted in an increase in cascade throat area causing the shock to start at a lower corrected fan speed. The acoustic results without acoustically absorbing liners showed substantial reduction in multiple pure tone levels. However, an increase in the blade passing frequency noise at takeoff fan speed accompanied the MPT reduction. The net result however, was a reduction in the maximum 1000-foot (304.8 m) altitude level flyover PNL. For the case with acoustic treatment in the inlet outer wall, the takeoff noise increased relative to an acoustically treated baseline. This was largely due to the increased blade passing frequency noise which was not effectively reduced by the liner.

Jutras, R. R.↗

NASA NTRS1974

High-tip-speed fiber composite compressor blades: Vibration and strength analysis

An analytical procedure is described which couples composite mechanics computer codes with NASTRAN. This procedure was used to perform a detailed analysis of a high-tip-speed fiber composite compressor fan blade. The results indicate that the various vibration modes of this blade are highly coupled. Mechanical load ply stresses are well below the corresponding room temperature strengths. Lamination residual stresses are likely to cause transply cracks and interply delamination. Transply cracks and relaxation of root fixity decrease the vibrational frequencies whereas centrifugal stiffening increases them. Comparisons of results for various parameters are presented in tabular and graphical form.

Chamis, C. C.↗

NASA NTRS1973

Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

Hudson, W. R.↗

NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 fps). The stages were tested statically in a 15-in.-dia model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 and 900 fps stages. For the 1050 fps stage, the design-speed forward-radiated power level was about 7 dB higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗

NASA NTRS1974

High-tip-speed fiber composite compressor blades - Vibration and strength analyses

Chamis, C. C.↗

NASA NTRS1974

Multiple pure tone noise generated by fans at supersonic tip speeds

The existence of clusters of pure tones at integral multiples of shaft speed has been noted for supersonic-tip-speed operation of fans and compressors. A continuing program to explore this phenomenon, often called combination-tone noise, has been in effect for several years. This paper reviews the research program, which involves a wide range of engines, compressor rigs, and special apparatus. Elements of the aerodynamics of the blade-associated shock waves are outlined and causes of blade-to-blade shock inequalities, responsible for the multiple tones, are described.

Sofrin, T. G.↗

NASA NTRS1975

Redesigned rotor for a highly loaded, 1800 ft/sec tip speed compressor fan stage 1: Aerodynamic and mechanical design

A highly loaded, high tip-speed fan rotor was designed with multiple-circular-arc airfoil sections as a replacement for a marginally successful rotor which had precompression airfoil sections. The substitution of airfoil sections was the only aerodynamic change. Structural design of the redesigned rotor blade was guided by successful experience with the original blade. Calculated stress levels and stability parameters for the redesigned rotor are within limits demonstrated in tests of the original rotor.

Halle, J. E.↗

NASA NTRS1975

An application of the Ogee tip

Wind tunnel tests show that the aerodynamic performance of a rectangular 3-D wing is increased by changing its tip to an ogee shape. Potential gains in both cruise and climb performances for a modified Beech Baron aircraft indicate that incremental changes in performance are on the order of the data scatter associated with applied flight test techniques.

Vogel, J. M.↗

NASA NTRS1975

A new arc heater shroud test technique for thermo-structural testing of full-scale, nose-tip skirt materials

An arc heater shroud test technique was developed for thermostructural testing of full-scale, missile nose tip-skirt assemblies. Reentry trajectory simulation is provided by changing the arc heater operation in a prescribed manner through manual and automatic controls. Excellent test repeatability allows screening of materials by direct comparison of test results. Continuous recordings of model surface temperature, pressure, heat flux, and model internal temperatures are made at several locations during the test.

Williams, R. R.↗