Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Heterogeneous photo-Fenton-like degradation of emerging pharmaceutical contaminants in wastewater using Cu-doped MgO nanoparticles

In this study, a facile thermal decomposition method was utilized to synthesize Cu-doped MgO nanoparticles possessing mesoporosity. These mesoporous Cu doped MgO nanoparticles were shown to be efficient photo-Fenton-like catalysts for the degradation of emerging pharmaceutical contaminants in wastewater and were able to completely oxidize salicylic acid within 1 hour under optimized conditions. Tetracycline was shown to be converted to other intermediates with a large portion of it undergoing full mineralization. Batch experiments were conducted to demonstrate the effects of Cu loading on MgO, overall catalyst loading, and H 2 O 2 concentration on the salicylic acid and tetracycline conversion and rate constants. Quenching experiments revealed that both •OH radicals or HO 2 •/•O 2 - radicals were involved in the reaction, with the latter showing a higher contribution. The surface dissolution of MgO was shown to facilitate a high pH environment which completely prevented Cu from leaching out of the catalyst while retaining high activity. The catalyst reusability was shown to be satisfactory with high activity and conversion being preserved over five cycles.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Investigation of fouling mechanisms for diesel engine exhaust heat recovery

The effect of diesel engine exhaust fouling on heat and mass exchangers for waste heat recovery is investigated. Experiments are conducted for a range of operating conditions relevant to the use of the waste heat from a diesel engine for powering a 2.71 kW capacity absorption heat pump. Thermal resistances of fouling layers as well as their effects on pressure drop are determined, and the underlying mechanisms for deposition and removal are investigated. Fouling layer effects are most severe for the lowest coolant temperatures and 100% generator load. At these conditions, the fouling thermal resistance is approximately 70% of the total resistance, and the ratio of the steady-state pressure drop to the baseline pressure drop is 3.25. Flow induced shear is found to be the primary growth inhibiting mechanism at high exhaust velocities. Findings from this study can guide heat exchanger design for a variety of waste heat recovery systems.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Maximizing oil production from water alternating gas (CO 2 ) injection into residual oil zones: The impact of oil saturation and heterogeneity

Residual oil zones (ROZs) are widespread reservoirs, characterized by oil at residual saturation, either underlying oil fields (brownfield) or lateral (greenfield) to such fields. These reservoirs have the potential to produce volumes of oil sufficiently significant to make appreciable impacts on the US’s oil reserves and associated incidental CO 2 sequestration. The objective of this study is to improve our understanding the impact of heterogeneous and low oil saturations, in brownfield ROZs, on the effectiveness of water alternating gas (WAG) injection strategies. ROZs occur in the Permian Basin and elsewhere, and operators are using CO 2 injection for enhanced oil recovery (EOR) in these zones. The consensus model for the formation of ROZs is that they were formed by the effect of faster regional aquifer flow, acting over millions of years. Both the magnitude of oil saturation and the spatial distribution of oil differ from water-flooded main pay zones (MPZs). To explore the most effective injection strategies, we conducted simulations of CO 2 injection into synthetic geologic reservoirs. These simulations focused on injection into reservoirs subject to either man-made waterflooding or long-term natural waterflooding. By exploring the impact of varying: oil saturation; well patterns; reservoir heterogeneity; and permeability anisotropy, we attempt to quantify the factors that most influence the effectiveness of WAG injection. WAG ratios (the ratio of injected water and CO 2 , in reservoir volumes) of interest are those that either minimize the net CO 2 utilization ratios or maximize oil production rates. In general, the most effective WAG ratios for ROZs, are consistently less than those observed undergoing CO 2 injection in the same geologic reservoir models after traditional (man-made) waterflooding. This work demonstrates that most favorable WAG ratios for oil production in ROZs are different from those in traditional MPZs because of oil saturation differences. Therefore, CO 2 injection into both zones or directly copying WAG injection designs from MPZs to ROZs might not maximize oil production.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Technology, technology, technology: An integrated assessment of deep decarbonization pathways for the Canadian oil sands

As a party to the Paris Agreement, Canada has an ambitious climate target of net-zero emissions by 2050. The country also holds the world's third largest oil reserves in the Alberta oil sands. Given increasing emissions from the oil sands sector, achieving Canada's net-zero target requires significant oil sands decarbonization. If, while phasing out fossil fuels, there is still a demand for Canadian oil sands, then the decarbonization of the resource production process becomes crucial. In this study, we use an enhanced version of the Global Change Analysis Model (GCAM) with a detailed unconventional oil sector for Canada, including mining and in situ resources. We ask, what is the future of the oil sands sector in deeply decarbonized global and Canadian economies? We address this question under four mitigation scenarios with varying global net-zero GHG emissions constraints, three additional representative lower carbon extraction technologies available for the oil sands sector, as well as global direct air capture (DAC) deployment. We find that lower carbon technology deployment allows a 20%–44% increase in oil sands production by 2050 for scenarios with net-zero GHG emissions in 2100 or 2075. DAC helps maintain oil sands production in the most ambitious global decarbonization scenario (net-zero GHG by 2050), without which low international oil demand makes Canadian oil sands production uncompetitive. Canadian oil sands production thus depends highly on the availability of lower carbon extraction technologies and international oil demand, which to a certain extent relies on the availability and global deployment of negative emissions technologies.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

La 3+ and Y 3+ interactions with the carboxylic acid moiety at the liquid/vapor interface: Identification of binding complexes, charge reversal, and detection limits

Specific interactions of yttrium and lanthanum ions with a fatty acid Langmuir monolayer were investigated using vibrational sum frequency spectroscopy. The trivalent ions were shown to interact with the charged form of the carboxylic acid group from nanomolar concentrations (<300 nM). Analysis of the spectral features from both the symmetric and the asymmetric carboxylate modes reveals the presence of at least three distinct coordination structures linked to specific binding configurations. Although the same species were identified for both La 3+ and Y 3+ , they display a different concentration dependence, highlighting the ion-specificity of the interaction. From the analysis of the response of interfacial water molecules, the reversal of the surface charge, as well as the formation of yttrium hydroxide complexes, were detected upon increasing the amount of salt in solution. The binding interaction and kinetics of absorption are sensitive to the solution pH, showing a distinct ion speciation in the interfacial region when compared to the bulk. Changing the subphase pH or adding a monovalent background electrolyte that promotes deprotonation of the carboxylic acid headgroup could further improve the detection limit of La 3+ and Y 3+ to concentrations < 100 nM. These findings demonstrate that nM concentrations of trace metals contaminants, typically found on monovalent salts, can significantly influence the binding structure and kinetics in Langmuir monolayers.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

A physics-informed and hierarchically regularized data-driven model for predicting fluid flow through porous media

This paper presents a new deep learning data-driven model for predicting structure dependent pore-fluid velocity fields in rock. The model is based on a Convolutional Auto-Encoder (CAE) artificial neural network capable of learning from image data generated by direct numerical simulations of fluid flow through pore-structures, such as by Lattice Boltzmann or molecular dynamics methods. The main novelty of the model in comparison to previous CAE-based data-driven approaches consists of three parts. The first is a methodology for decomposing the full-domain of the porous media into sub-regions, or “sub-domains”, in order to reduce the overall size of the CAE, batch process the sub-domains in parallel, and enable the CAE to learn local and generalizable nonlinear mappings of pore-fluid velocities. The second consists of embedding the finite difference solutions of the incompressible Navier-Stokes and continuity equations into convolutional layers prior to the CAE in order to provide the CAE with knowledge of fluid dynamics physics (PhyFlow). The third main novelty is that the training of the CAE is regularized with a hierarchical loss function that encourages the learning of fluid flow patterns (in a way similar to ranked modes in principal component analysis), ranking from most to least important. This is shown to increase the stability in learning, reduce over-fitting, and promote interpretability of the CAE neural network layers (HierCAE). The comprehensive new data-driven model, which we call the PhyFlow-HierCAE model, is shown to exhibit improved accuracy and generalizability of flow field predictions over conventional CAE models, attributable to the embedded physical knowledge and the hierarchical regularization, as well as realize orders of magnitude speed-ups in computation times as a surrogate for the direct numerical simulations. Examples of training and forward predictions on unseen pore-structures are provided and evaluated for data from Lattice Boltzmann and molecular dynamics simulations of pore-fluid flow. The model is shown to be a fast and accurate emulator (or “surrogate”) for predicting effective permeability of unseen pore-structures based on learning from relatively small direct numerical simulation datasets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ultralow Thermal Conductivity in Cs–Sb–Se Compounds: Lattice Instability versus Lone-Pair Electrons

Lone-pair electrons (LPE) are known to lead to large anharmonicity in materials and thus to low lattice thermal conductivity (k). Materials with LPE typically have lower k than those with similar compositions but without LPE. In this study, we investigate thermal transport properties in Cs-Sb-Se ternary compounds by first principles methods and show that LPE do not necessarily guarantee the lowest k.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2023

Evolution of Pore Structure in Organic-Lean and Organic-Rich Mudrocks

The pore structure of mudrocks is a key characteristic to evaluate flow behavior through these rocks. Although significant advances have been made to resolve pore characteristics, porosity evolution, or pore connectivity, there is still insufficient knowledge linking porosity evolution to flow and transport in mudrocks. To better understand these links, we conducted very small-angle (VSANS) and small-angle neutron scattering (SANS) experiments on 13 sets of mudrocks from global locations, characterized by differences in composition, maturity, and depositional environment. Our results indicate that a homogeneous pore structure reflects a stable and low-energy depositional environment. Organic-lean mudrocks mainly contain pores <10 nm, which restricts flow and is beneficial for, e.g., caprock seal integrity. Increasing maturity as a result of increasing burial depth, and therefore, temperature leads to porosity evolution. In organic-rich mudrocks (ORMs), this happens through the generation of organic matter pores and pore preservation around diagenetically formed carbonates. ORMs mainly contain macropores (>50 nm), favoring production from, e.g., unconventional reservoirs. SANS-derived pore size distributions will help to better understand fluid imbibition and flow properties in mudrocks through comprehensive quantitative characterization of the nano- to micron scale pore network conduits and their relationships to burial diagenesis.

58 GEOSCIENCES↗
DOE OSTI2020

Surface Reactivity Analysis of the Crude Oil–Brine–Limestone Interface for a Comprehensive Understanding of the Low-Salinity Waterflooding Mechanism

Low-salinity waterflooding (LSWF) has proven to improve oil recovery in carbonate formations through rock wettability alteration, although the underlying mechanism remains elusive. Multivalent ionic exchange and calcite dissolution have usually been investigated using geochemical analysis in secondary coreflooding. In this work, coreflooding, in tertiary mode, coupled with a surface reactivity analysis approach was employed to investigate the interplay of wettability alteration mechanisms such as mineral dissolution, electrostatic bond attraction, and the effect of pH at in situ conditions. Improved oil recovery (IOR) in tertiary mode observed by coreflooding in Indiana limestone rocks showed an ionic strength dependence, that is, reducing brine ionic strength resulted in an increase in oil recovery. Coreflooding results showed that the seawater and low-salinity brines deprived of Mg 2+ ions resulted in the lowest IOR in tertiary mode, indicating the significance of Mg 2+ on IOR in limestone rocks. Similar results were observed through the contact angle measurement showing the limestone rock wettability state dependence on ionic strength and the effect of Mg2+ ions. Surface reactivity analysis showed an increase in solution pH, Ca 2+ and Mg 2+ ions concentration in the effluent solution from the coreflooding in tertiary mode using low salinity brines (about 40 and 20% increase in the effluent composition for Ca 2+ and Mg 2+ , respectively). These changes in solution composition were used to calculate the in situ oil–brine and rock–brine zeta potential using a validated surface complexation model, showing the changes of zeta potential as brine is injected into limestone rocks. The results show that using seawater-like brine in tertiary mode resulted in no mineral dissolution or ionic exchange. However, improved oil recovery (IOR) using such seawater-like brine was due to wettability alteration caused by reduced electrostatic bond attraction associated with Mg 2+ ions [from 2.6 × 10 –13 (mol/m 2 ) 2 for formation water salinity to 1.5 × 10 –13 (mol/m 2 ) 2 for seawater salinity]. Using low-salinity brines in tertiary mode improved oil recovery by mineral dissolution, resulting in oil desorption and an increase in solution pH. Finally, the increase in solution pH also resulted in reduced electrostatic bond attraction which lead to rock wettability alteration using low-salinity brines.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2026

Microstructure, Transport, and Mechanics of Compacted Clay Simulated at the 0.1 μm Scale (1400 Smectite Clay Particles) Using a Coarse-Grained Model with Explicit Counterions

Clay-rich geomaterials play a critical role in many subsurface systems. The macroscale properties of these materials (low permeability, high ionic conductivity, high swelling pressure, etc.) are sensitive to molecular-level adsorption and hydration interactions at clay−water interfaces. Efforts to develop multiscale simulation approaches to predict these properties reveal a scale gap between atomistic simulations (typically limited to systems smaller than 10 nm) and continuum-scale models (which use computational grid elements with dimensions ≳ 10 μm). In this study, we present a coarse-grained (CG) framework that partly bridges this gap by simulating compacted smectite clay assemblages with dimensions of 0.1 μm containing 1,400 clay particles across a range of dry densities (1,050 to 1,850 kg·m −3 ) and Na/Ca counterion compositions (Na fraction ranging from 0.2 to 1). The simulated systems, along with their reconstructed binary three-dimensional pore networks, are used to evaluate the microstructure, pore size distribution, tortuosity, ion diffusivity, and swelling pressure of compacted smectite clay. Results show that our approach captures important features of the mesoscale heterogeneity of compacted clays, including tactoid formation, hierarchical porosity, and anisotropic pore networks. Results also reveal how compaction and counterion composition govern emergent behaviors, including dominant pore sizes, directional transport, and electrochemical response. This work highlights the potential of CG simulations to bridge molecular and continuum scales and to advance geotechnical and environmental applications involving clay-rich materials as well as related nanoporous media such as geopolymers and calcium-silicate-hydrate. However, the results also suggest that accurate prediction of certain microstructural and mechanical properties (e.g., swelling pressure) may require even larger-scale systems on the order of 1 μm.

02 PETROLEUM↗
DOE OSTI2020

Fast Advective Water Flow through Nanochannels in Clay Interlayers: Implications for Moisture Transport in Soils and Unconventional Oil/Gas Production

Water flow in nanometer or sub-nanometer hydrophilic channels bears special importance in diverse fields of science and engineering. However, the nature of such water flow remains elusive. In this work, we report our molecular-modeling results on water flow in a sub-nanometer clay interlayer between two montmorillonite layers. We show that a fast advective flow can be induced by evaporation at one end of the interlayer channel, that is, a large suction pressure created by evaporation (~818 MPa) is able to drive the fast water flow through the channel (~0.88 m/s for a 46 Å-long channel). Scaled up for the pressure gradient to a 2 μm particle, the velocity of water is estimated to be about 95 μm/s, indicating that water can quickly flow through a μm-sized clay particle within seconds. The prediction seems to be confirmed by our thermogravimetric analysis of bentonite hydration and dehydration processes, which indicates that water transport at the early stage of the dehydration is a fast advective process, followed by a slow diffusion process. The possible occurrence of a fast advective water flow in clay interlayers prompts us to reassess water transport in a broad set of natural and engineered systems such as clay swelling/shrinking, moisture transport in soils, water uptake by plants, water imbibition/release in unconventional hydrocarbon reservoirs, and cap rock integrity of supercritical CO 2 storage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗