Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Photocatalytic and photoelectrochemical performance of Ta{sub 3}N{sub 5} microcolumn films fabricated using facile reactive sputtering

This paper presents the photocatalytic and photoelectrochemical (PEC) properties of Ta{sub 3}N{sub 5} microcolumn films. The highlights include (1) overcoming the fundamental barrier of standard reactive sputtering for fabricating microcolumns; (2) preventing unnecessary complexity from complicating facile sputtering; (3) an alternative but effective approach for fabricating Ta{sub 3}N{sub 5} without using caustic NH{sub 3} gases; (4) investigating morphology tuning for favorable photocatalysis and PEC reactions; and (5) elucidating the relationships of the structures, morphologies, and properties of Ta{sub 3}N{sub 5} microcolumns. High-resolution transmission electron microscopy and selective-area electron diffraction verified the polycrystallinity of Ta{sub 3}N{sub 5} microcolumns, of which the elemental compositions and stoichiometry were measured using electron-probe energy dispersive spectroscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy. The corresponding band gap was determined to be approximately 2.1 eV. The sample exhibited a superior photodegradation capability; the photodegradation rate constant k was determined to be approximately 1.4 times higher than that of P25 under UV irradiation. A photocatalytic and PEC cycling test indicated the photodegradation reusability and photostability of the Ta{sub 3}N{sub 5} microcolumns. The incident photon-to-current efficiency performance reached 6%, suggesting that these microcolumns hold potential for application in PEC devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sputter-deposited low-stress boron carbide films

Significant challenges have been faced in the manufacturing of low-stress B 4 C films. Here, we demonstrate a set of process parameters for direct-current magnetron sputter deposition of smooth, high-purity, amorphous B 4 C films with near-zero total residual stress and with thicknesses up to 10 μm. Films are characterized by a combination of high-energy ion scattering, x-ray diffraction, electron microscopy, and stress measurements based on substrate curvature. In order to facilitate the process transfer to other sputtering geometries, the favorable deposition conditions are correlated with distributions of landing energies and incident angles of depositing species estimated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Based on such simulations, a decrease in compressive stress with increasing Ar working gas pressure is attributed to the corresponding broadening of the angular distribution of depositing species and associated atomic shadowing effects.

36 MATERIALS SCIENCE↗

High-Power Impulse Magnetron Sputter Deposition of Boron Carbide with Full-Face Erosion Magnetron and Mixed Ar-Ne Plasma

Boron carbide (B 4 C) is an attractive inertial confinement fusion ablator material. The fabrication of B4C ablators by magnetron sputtering requires process optimization. To increase process flexibility, here we explore high-power impulse magnetron sputter (HiPIMS) deposition of B 4 C in pure Ar and mixed Ar-Ne plasmas. Here, the results show that higher plasma discharge currents can be reached with a mixed Ar-Ne plasma in the entire working pressure range studied (5 𝑡𝑜 50 mTorr). At 45 mTorr with 10% of Ne in the Ar-Ne mix, high peak target current densities of ~1 A cm −2 were demonstrated. Films deposited with such a mixed Ar-Ne plasma with a full-face erosion magnetron source on substrates biased at −25 V exhibited higher density and improved mechanical properties, albeit with higher compressive residual stresses compared to the case of HiPIMS deposition in a pure Ar plasma. This work demonstrates additional process flexibility of the HiPIMS discharge mode for the deposition of B 4 C coatings.

Ablator capsule↗

ELM sputter erosion modeling of a tungsten coated small angle slot divertor in DIII-D

We modeled plasma edge localized mode (ELM) sputter erosion for a Small Angle Slot divertor with a tungsten coated region (SAS-VW), designed for experiments in the DIII-D tokamak, and proposed for use in future advanced tokamaks. The simulations use a free-streaming, 1000 eV, C +6 and D +1 ELM impingement model, with SOLPS-ITER, ITMC-DYN, and REDEP/WBC code packages for background plasma, material response, and erosion/redeposition respectively. The results show ELM'ing plasma gross and net tungsten erosion fluxes of the mixed-material C/W surface peaking at the slot entrance region, and an order of magnitude higher than for non-ELMs. The per-pulse erosion, however, remains low, of order 0.5 nm, due to expected moderate ELM frequencies and duration in DIII-D. Here, the ELMs result in a ~25x higher peak sputtered W current leaving the divertor slot region, towards the core plasma, compared to the ELM-free plasma case. The time-integrated escape current, however, may not significantly affect core plasma high-Z contamination concerns, for a 1% ELM duty factor, but may be an issue for higher frequency ELMs. In general, the modeling results appear favorable for effective testing of the SAS-VW divertor in DIII-D, and extrapolation to innovative divertor designs in future ITER-like and DEMO fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Origin of preferential sputtering in a-SiO{sub 2} during ion beam synthesis of nanocrystals

Ion implantation into a-SiO{sub 2} leads to the self-assembly of nanocrystal arrays having application in optical and nonvolatile memory devices. It was recently noted that nanocrystal nucleation occurs in oxide regions exhibiting variations in oxygen concentration resulting from preferential sputtering. Here we report quantum-mechanical calculations that probe the atomic-scale dynamics following ion-induced low-energy recoils and show that preferential sputtering does not result directly from short-time collisional processes. These processes do, however, result in a population of loosely bound oxygen atoms connected to the amorphous network by a single Si-O bond. Thus, the well-known diffusion and relaxation processes that control stable defect formation at long times following recoil events lead to variations in O concentration in damaged regions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Self-Sputtering Far above the Runaway Threshold: An Extraordinary Metal-Ion Generator

When self-sputtering is driven far above the runaway threshold voltage, energetic electrons are made available to produce 'excess plasma' far from the magnetron target. Ionization balance considerations show that the secondary electrons deliver the necessary energy to the 'remote' zone. Thereby, such a system can be an extraordinarily prolific generator of usable metal ions. Contrary to other known sources, the ion current to a substrate can exceed the discharge current. For gasless self-sputtering of copper, the usable ion current scales exponentially with the discharge voltage.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The Effects of Sputtering Target Preparation and Deposition Temperature on ZnTe:Cu Film Properties

A back contact containing a sputtered ZnTe:Cu interface layer can produce high-performing thin-film CdS/CdTe photovoltaic devices. We have found that varying the ZnTe:Cu sputtering target fabrication processes and deposition temperature can affect material properties of the ZnTe:Cu films and the resulting device performance. Two different target 'recipes' with various copper contents were used to study changes in the compositional, structural, optical, and electrical properties of ZnTe:Cu films. Substrate temperature during deposition was also varied to investigate the temperature dependence of the films. It was found that the target recipe, Cu concentration in the target, and deposition temperature affect the composition of the ZnTe:Cu films, which impacts their structural, optical, and electrical properties.

14 SOLAR ENERGY↗

Crystallographic texture control of sputtered HfN thin films using low oxygen partial pressures

The authors studied the development of crystallographic texture in hafnium nitride (HfN) films deposited by off-normal incidence reactive magnetron sputtering at room temperature. Films are prepared with and without added oxygen in N{sub 2}/Ar mixtures. Texture measurements were performed by x-ray pole figure analysis of the (111) and (200) diffraction peaks. The authors found that HfN deposited at 40 deg. without added oxygen has a strong <100> fiber texture with no in-plane alignments showing the dominance of thermodynamic effects in the course of texture evolution. Oxygen is deliberately introduced into the sputtering gas ambient to study its effects on microstructure formation. As the oxygen partial pressure (O{sub 2} pp) is increased in the range of 1.33x10{sup -5} to 1.33x10{sup -4} Pa, HfN out-of-plane orientation changed to <111> with a substantial in-plane alignment in <100> direction as well. In this case, texture analysis of each individual diffraction peak revealed the existence of two populations of grains indicating a competition between (111) and (200) planes. A transition towards hafnium oxynitride phases occurred at high O{sub 2} pp's. The authors propose that oxygen presence during deposition reduces the adatom surface mobility, which enables kinetic effects to govern the texture formation and thus leads to a biaxial alignment in HfN films.

36 MATERIALS SCIENCE↗

Effect of pulse frequency on the ion fluxes during pulsed dc magnetron sputtering

The ion fluxes and energies which impinge on the substrate during the deposition of chromium nitride by asymmetric bipolar pulsed dc reactive magnetron sputtering have been analyzed using energy resolved mass spectrometry. It has been found that there is a remarkable increase in ion flux at higher pulse frequencies and that the peak ion energy is directly related to the positive voltage overshoot of the target voltage. The magnitude of the metal flux depositing on the substrate is consistent with a 'dead time' of {approx}0.7 {mu}s at the start of the on period. The variation of the ion flux with pulse frequency has been explained by a simple model in which the ion density during the on period has a large peak which is slightly delayed from the large negative voltage overshoot which occurs at the start of the on pulse due to increased ionization at that time. This is consistent with the previously observed phenomena in pulsed sputtering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of deposition pressure and pulsed dc sputtering on pumping properties of Ti-Zr-V nonevaporable getter films

The performance of a UHV vessel can be improved with a new CERN technology nonevaporable getter (NEG) coating, which is already widely used for accelerator vacuum chambers. Better understanding of the processes involved in NEG film deposition, activation, and poisoning should allow optimization and engineering of the film properties, which are necessary for a particular application. Ti-Zr-V NEG films were created by magnetron sputtering from a single Ti-Zr-V target, and the NEG performance and morphology dependence on deposition pressure, sputtering conditions, and substrate surface roughness have been investigated. It was found that the average grain size of the Ti-Zr-V film was 5-6 nm and was broadly independent of the substrate material and deposition conditions. However, film topography and density were shown to depend very much on the substrate surface roughness and deposition conditions. Rough substrates, high working pressures, and the absence of ion bombardment produced open columnar structures, whereas smooth substrates, ion assistance, and low pressures produced much denser layers. X-ray photoelectron spectroscopy studies have shown that full regeneration occurred at 300 degree sign C but film activation started at temperatures of as low as 160 degree sign C. The CO sticking probability reaches its maximum after activation at 250 degree sign C and is found to be up to 0.3 with a pumping capacity in the range of 0.8-1.2 ML. The samples activated at 160 degree sign C have a reduced pumping speed and capacity by an order of magnitude.

36 MATERIALS SCIENCE↗

Nitrogen stabilized reactive sputtering of optimized TiO{sub 2-x} photocatalysts with visible light reactivity

Photoreactive and visible light responsive nonstoichiometric mixed-phase titania was prepared by reactive direct current magnetron sputtering. Trace amounts of nitrogen were added for process stabilization without being incorporated into the films. Based on the CO{sub 2} photoreduction tests and structural and optical characterization, the influence of the trace nitrogen on the sputtered nonstoichiometric TiO{sub 2} was studied and was compared to nitrogen-doped titania.

36 MATERIALS SCIENCE↗

Transparent conducting Si-codoped Al-doped ZnO thin films prepared by magnetron sputtering using Al-doped ZnO powder targets containing SiC

Transparent conducting Al-doped ZnO (AZO) thin films codoped with Si, or Si-codoped AZO (AZO:Si), were prepared by radio-frequency magnetron sputtering using a powder mixture of ZnO, Al{sub 2}O{sub 3}, and SiC as the target; the Si content (Si/[Si+Zn] atomic ratio) was varied from 0 to 1 at. %, but the Al content (Al/[Al+Zn] atomic ratio) was held constant. To investigate the effect of carbon on the electrical properties of AZO:Si thin films prepared using the powder targets containing SiC, the authors also prepared thin films using a mixture of ZnO, Al{sub 2}O{sub 3}, and SiO{sub 2} or SiO powders as the target. They found that when AZO:Si thin films were deposited on glass substrates at about 200 degree sign C, both Al and Si doped into ZnO acted as effective donors and the atomic carbon originating from the sputtered target acted as a reducing agent. As a result, sufficient improvement was obtained in the spatial distribution of resistivity on the substrate surface in AZO:Si thin films prepared with a Si content (Si/[Si+Zn] atomic ratio) of 0.75 at. % using powder targets containing SiC. The improvement in resistivity distribution was mainly attributed to increases in both carrier concentration and Hall mobility at locations on the substrate corresponding to the target erosion region. In addition, the resistivity stability of AZO: Si thin films exposed to air for 30 min at a high temperature was found to improve with increasing Si content.

36 MATERIALS SCIENCE↗

Effects of pulsed sputtering frequency on the uniformity of Al:ZnO's transparent conductive oxide properties for solar cell applications

Bipolar pulsed magnetron sputtering is used to deposit Al doped ZnO (AZO) on a glass substrate for a transparent conducting oxide in a solar cell structure. A 5x25 in.{sup 2} AZO target was sputtered by 50-250 kHz bipolar pulsed dc power supply to deposit a 400x400 mm{sup 2} area by swinging back and forth. Sheet resistance, surface morphology, and optical transmittance were measured at different positions on 16 witness samples (small glass slides) to evaluate uniformity. In the thickness of 800 nm, the average value of sheet resistance was 30 {Omega}/{open_square} and the average resistivity was 2.1x10{sup -3} {Omega} cm. Transmittance was 50%-80% over the visible range. The nonuniformities of thickness, transmittance, and resistivity in the 400x400 mm{sup 2} area were 5.8%, 0.8%, and within 9.5%, respectively.

14 SOLAR ENERGY↗

Microstructure and chemical wet etching characteristics of AlN films deposited by ac reactive magnetron sputtering

The influence of the surface morphology of a molybdenum underlayer on the crystallinity and etchability of reactively sputtered c-axis oriented aluminum nitride thin films was investigated. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, high resolution x-ray diffraction, and defect selective chemical etching were used to characterize the microstructure of the Mo and AlN films. 1000 nm thick films of AlN with a full width at half maximum (FWHM) of the x-ray rocking curve ranging from 1.1 deg. to 1.9 deg. were deposited on 300 nm thick Mo underlayers with a FWHM of around 1.5 deg. The Ar pressure during the Mo deposition had a critical effect on the Mo film surface morphology, affecting the structure of the subsequently deposited AlN films and, hence, their wet etching characteristics. AlN films deposited on Mo sputtered at a relatively high pressure could not be etched completely, while AlN films deposited on low pressure Mo etched more easily. Postdeposition etching of the Mo surface in Ar rf discharge prior to deposition of the AlN film was found to influence the formation of AlN residuals that were difficult to etch. Optimal rf plasma etching conditions were found, which minimized the formation of these residuals.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High rate reactive magnetron sputter deposition of Al-doped ZnO with unipolar pulsing and impedance control system

Al-doped ZnO (AZO) films were deposited on quartz glass substrates, unheated and heated to 200 deg. C, using reactive sputtering with a special feedback system of discharge impedance combined with midfrequency pulsing. A planar Zn-Al alloy target was connected to the switching unit, which was operated in a unipolar pulse mode. The oxidation of the target surface was precisely controlled by a feedback system for the entire O{sub 2} flow ratio including ''the transition region''. The deposition rate was about 10-20 times higher than that for films deposited by conventional sputtering using an oxide target. A deposition rate of AZO films of 390 nm/min with a resistivity of 3.8x10{sup -4} {Omega} cm and a transmittance in the visible region of 85% was obtained when the films were deposited on glass substrates heated to 200 deg. C with a discharge power of 4 kW.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of working pressure on physical properties of tungsten-oxide thin films sputtered from oxide target

Tungsten-oxide films were deposited on glass substrates from a metal-oxide target by nonreactive radio-frequency sputtering. The authors have studied the effect that changing Ar gas pressure has on the electrical, optical, and chemical composition in the thin films. Resistivity of WO{sub 3} changed ten orders of magnitude with working gas pressure values from 20 to 80 mTorr. Thin films deposited at 20 mTorr of Ar sputtering pressure showed lower resistivity and optical transmittance. X-ray photoelectron spectroscopy (XPS) measurements revealed similar chemical composition for all samples irrespective of Ar pressure used. However, XPS analyses of the evolution of W 4f and O 1s peaks indicated a mixture of oxides dependent on the Ar pressure used during deposition.

36 MATERIALS SCIENCE↗

Orientation-dependent ion beam sputtering at normal incidence conditions in FeSiAl alloy

The authors have performed Ar+ broad ion beam sputtering of a polycrystalline Fe-Si-Al alloy at normal incidence at energies varying from 6 to 10 keV. Sputtering results in the formation of etch pits, which can be classified in three shapes: triangular, rectangular, and square. As each grain of individual orientation exhibits a certain type of pattern, the etch pits were correlated with the crystal orientations by electron backscattered diffraction technique.

36 MATERIALS SCIENCE↗

Lithium phosphorus oxynitride solid-state thin-film electrolyte deposited and modified by bias sputtering and low temperature annealing

Amorphous lithium phosphorus oxynitride (LiPON) solid-state thin-film electrolyte has been deposited and characterized. The thin films were prepared by rf magnetron sputtering under various substrate biases. By fabricating under different substrate biases and applying low temperature annealing (473 K), the properties of the LiPON thin-film electrolytes and the electrolyte/cathode interfaces were modified. The ionic conductivity as high as 9.4x10{sup -4} S m{sup -1} can be obtained by depositing at optimal bias. The performances of the consequently fabricated SnO{sub 2}/LiPON/LiMn{sub 2}O{sub 4} all-solid-state lithium ion thin-film batteries were improved using the bias sputtering technique, due to the enhanced the ionic conductivity and uniform interface.

36 MATERIALS SCIENCE↗