Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHEAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Buried wire gage for wall shear stress measurements

A buried wire gage for measuring wall shear stress in fluid flow was studied and further developed. Several methods of making this relatively new type of gage were examined to arrive at a successful technique that is well-suited for wind-tunnel testing. A series of measurements was made to demonstrate the adequacy of a two-point calibration procedure for these gages. The buried wire gage is also demonstrated to be ideally suited for quantitative measurement of wall shear stress in wind-tunnel testing.

Murthy, V. S.↗
NASA NTRS1977

Modeling of pressure spectra in a turbulent shear flow

The development of the pressure spectrum has been followed from its separation into turbulent-turbulent and turbulent-mean square contributions to a unified spectral model. The model is obtained by Fourier transforming the integral solution to Poisson's equation for an isotropic, homogeneous, constant mean shear flow. The variations in the asymptotic form for the mean-shear spectrum is discussed. It is noted that the spectra are associated with the particular velocity field selected, and that by an appropriate choice of spectral forms, the mean-square pressure of the flow may be calculated.

Beuther, P.↗
NASA NTRS1978

Solitary Rossby waves in zonal shear flows and their interactions

Interactions of long-wave solitons propagating in shear flows are described by a coupled pair of Korteweg-de Vries equations. The basic equation of motion for the analysis is the quasi-geostrophic forecast equation, and the interaction of two wave modes is studied. The solution for mode 1-mode 2 interaction of solitary waves in an asymmetric shear flow of a barotropic atmosphere with divergence is constructed. Streamline patterns for certain flows are obtained. An unsteady solitary wave solution for a modified Korteweg-de Vries equation is derived.

Redekopp, L. G.↗
NASA NTRS1979

Fixed-base simulation study of decoupled longitudinal controls during approach and landing of a medium jet transport in the presence of wind shear

The use of decoupled longitudinal controls during the approach and landing of a typical twin-engine jet transport in the presence of wind shear was studied. The simulation included use of a localizer and flight director to capture and maintain a 3 deg glide slope. The pilot then completed the landing by using visual cues provided below an altitude of 200 m by closed-circuit television and a terrain model. The decoupled controls used constant prefilter and feedback gains to provide steady state decoupling of flight path angle, pitch angle, and forward velocity. The use of the decoupled control system improved pilot performance during the approach and at touchdown in the presence of wind shears. The pilots preferred the decoupled controls and rated the task 1 to 3 increments better on a pilot rating scale, depending on wind conditions, than was the case when conventional controls were used.

Miller, G. K., Jr.↗
NASA NTRS1978

The large-scale organized structure in free turbulent shear flow and its radiation properties

Modeling of the large-scale coherent structures in a turbulent free shear flow is described. The objective is to gain insight into the interaction between the large-scale structure and the fine-grained turbulence. Some aerodynamic sound radiation properties of the large-scale structure are examined. It is found that the dominant contributions to the radiation come from shear noise rather than self-noise. The fact that a pure tone excitation leads to broadband amplification is most probably due to the enhancement of the fine-grained turbulence by the coherent structure. Numerical modeling of the coherent structure is also discussed.

Liu, J. T. C.↗
NASA NTRS1979

Scattering and distortion of the unsteady motion on transversely sheared mean flows

It is shown that the pressure and velocity fluctuations of the unsteady motion on a transversely sheared mean flow can be expressed entirely in terms of the derivatives of two potential functions. One of these is a convected quantity that can be specified as a boundary condition and is related to a transverse component of the upstream velocity field. The other can be determined by solving an inhomogeneous wave equation whose source term is also a convected quantity that can be specified as a boundary condition in any given problem. The general theory is used to study the interaction of an unsteady flow with a semi-infinite plate embedded in a shear layer. The acoustic field produced by this interaction is calculated in the limits of low and high frequency. The results are compared with experimental one-third octave sound pressure level radiation patterns. The agreement is found to be excellent, especially in the low frequency range, where the mean-flow and convective effects are shown to have a strong influence on the directivity of the sound.

Goldstein, M. E.↗
NASA NTRS1979

Equatorial wave-mean flow interaction - A numerical study of the role of latitudinal shear

A time-dependent primitive equation model for an equatorial channel is used to assess the interaction of equatorial Kelvin and mixed Rossby-gravity waves with the mean flow. The proposed model involves a semiimplicit time-differencing scheme and a finite-difference grid in the meridional plane. It is shown that forced equatorial waves interact with mean flow to produce equatorial jets characterized by downward-moving westerly (Kelvin wave forcing) and easterly (mixed Rossby-gravity wave forcing) shear zones, respectively. For parameters characteristic of the observed waves in the equatorial stratosphere, the wave-mean flow interaction process always reduces the amplitude of any initial cross-equatorial mean wind shear. The mean flow profile tends to become symmetric about the equator as the interaction process continues.

Holton, J. R.↗
NASA NTRS1979

Decoupled longitudinal controls for shear penetration in the terminal area environment

The use of decoupled longitudinal controls is simulated for the approach and landing of a twin engine jet transport in the presence of wind shear. Decoupled or independent control of pitch angle, flight-path angle and forward velocity using constant prefilter and feedback gains was compared to conventional control of a B-737 aircraft simulator. It is found that the mean flight-path angle, the mean glideslope error and the mean deviation in indicated airspeed generally improved when decoupled controls were used in the approach. An improvement in touchdown parameters was also observed, especially in strong shear, when 44% of conventionally-controlled flights impacted short of the runway. Simulator pilots reported improved approach performance and a reduced workload when decoupled controls were used.

Miller, G. K., Jr.↗
NASA NTRS1978

Application of a trigonometric finite difference procedure to numerical analysis of compressive and shear buckling of orthotropic panels

A numerical analysis developed for the buckling of rectangular orthotropic layered panels under combined shear and compression is described. This analysis uses a central finite difference procedure based on trigonometric functions instead of using the conventional finite differences which are based on polynomial functions. Inasmuch as the buckle mode shape is usually trigonometric in nature, the analysis using trigonometric finite differences can be made to exhibit a much faster convergence rate than that using conventional differences. Also, the trigonometric finite difference procedure leads to difference equations having the same form as conventional finite differences; thereby allowing available conventional finite difference formulations to be converted readily to trigonometric form. For two-dimensional problems, the procedure introduces two numerical parameters into the analysis. Engineering approaches for the selection of these parameters are presented and the analysis procedure is demonstrated by application to several isotropic and orthotropic panel buckling problems. Among these problems is the shear buckling of stiffened isotropic and filamentary composite panels in which the stiffener is broken. Results indicate that a break may degrade the effect of the stiffener to the extent that the panel will not carry much more load than if the stiffener were absent.

Stein, M.↗
NASA NTRS1979

Jet transport performance in thunderstorm wind shear conditions

Several hours of three dimensional wind data were collected in the thunderstorm approach-to-landing environment, using an instrumented Queen Air airplane. These data were used as input to a numerical simulation of aircraft response, concentrating on fixed-stick assumptions, while the aircraft simulated an instrument landing systems approach. Output included airspeed, vertical displacement, pitch angle, and a special approach deterioration parameter. Theory and the results of approximately 1000 simulations indicated that about 20 percent of the cases contained serious wind shear conditions capable of causing a critical deterioration of the approach. In particular, the presence of high energy at the airplane's phugoid frequency was found to have a deleterious effect on approach quality. Oscillations of the horizontal wind at the phugoid frequency were found to have a more serious effect than vertical wind. A simulation of Eastern flight 66, which crashed at JFK in 1975, served to illustrate the points of the research. A concept of a real-time wind shear detector was outlined utilizing these results.

Mccarthy, J.↗
NASA NTRS1979

Optimum design of laminated plates under shear

This paper is concerned with the optimum design of plates with orthotropic layers under shear. The plates considered are the laminates of N orthotropic layers whose principal material axes coincide with the plate axes. Each layer is assumed to have the same thickness and an equal number of fibers in the direction of + alpha sub i and - alpha sub i with respect to the plate axis. The fiber directions which give the highest shear buckling stress are found by utilizing a mathematical optimization technique.

Hirano, Y.↗
NASA NTRS1979

Investigation of a reattaching turbulent shear layer Flow over a backward-facing step

The paper studies incompressible flow over a backward-facing step in order to investigate the flow characteristics in the separated shear layer, the reattachment zone, and the redeveloping boundary layer after reattachment. It is shown that turbulent intensities and shear stress reach maxima in the reattachment zone, followed by rapid decay near the surface after reattachment. In addition, it is found that downstream of reattachment, the flow returns very slowly to the structure of an ordinary turbulent boundary layer.

Kim, J.↗
NASA NTRS1979

An analysis of interface crack in adhesively bonded lap shear joints

This paper presents an analytical study of interface crack problems in adhesively bonded lap shear joints. A convenient and accurate method of analysis is developed on the basis of conservation laws in elasticity and of the fundamental relationships in fracture mechanics of interface crack problems. The problem is eventually reduced to a system of linear algebraic equations of mixed-mode stress intensity factor solutions. One of the salient features of the present approach is that the interface crack-tip stress intensity solutions can be determined accurately and directly by the information extracted from the far field. Solutions of the interface crack problems in lap shear joints have been obtained for the cases of various adhesive/adherend material systems and geometric configurations of the crack and the joint. Of particular interest is the evaluation of the mixed-mode stress intensity factors and the associated energy release rates. They are determined explicitly to illustrate the fundamental nature of the joint fracture problem.

Wang, S. S.↗
NASA NTRS1980

Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. II - Wall shear stress

Asymptotic methods are used to calculate the shear stress at the wall for the interaction between a normal shock wave and a turbulent boundary layer on a flat plate. A mixing length model is used for the eddy viscosity. The shock wave is taken to be strong enough that the sonic line is deep in the boundary layer and the upstream influence is thus very small. It is shown that unlike the result found for laminar flow an asymptotic criterion for separation is not found; however, conditions for incipient separation are computed numerically using the derived solution for the shear stress at the wall. Results are compared with available experimental measurements.

Liou, M. S.↗
NASA NTRS1980

The near field interaction between a sound pulse and a jet shear layer

The in-flow and near field of a jet which is excited by an axial mass source located in the potential core is simulated numerically, taking due account of the jet spreading, and experimentally, using a shock-tube driver. Comparison is made for both excited and unexcited jets. It is shown that many of the features observed experimentally are consequences of the instability of the mean flow profile and not of turbulence. This instability is shown to be a significant amplifier of low frequency sound. The terms responsible for this amplification are those describing action between the fluctuating velocities and the gradient of the mean flow, which were identified by Ribner as the shear noise terms. The results demonstrate that a primary component of the observed shear noise in jets is generated by the mean profile instability.

Bayliss, A.↗
NASA NTRS1980

Normal and shear impact of layered composite with a crack - Dynamic stress intensification

The dynamic response of a layered composite under normal and shear impact is analyzed by assuming that the composite contains an initial flaw in the matrix material. One of the objectives was to develop an analytical method for determining dynamic stress solutions which should lead to a numerical method which utilizes Fourier transform for the space variable and Laplace transform for the time variable. The time-dependent angle loading is separated into two parts: a symmetric and a skew-symmetric with reference to the crack plane. By superposition, the transient boundary conditions consist of applying normal and shear tractions to a crack embedded in a layered composite; one phase of the composite could represent the fiber while the other could be the matrix. Mathematically, these conditions reduce the problem to a system of dual integral equations solved in the transform plane for the transform of the dynamic stress-intensity factor.

Sih, G. C.↗
NASA NTRS1980

Pilot-aircraft system response to wind shear

The nonlinear aircraft motion and automatic control computer model of Frost and Reddy has been expanded to incorporate the human pilot into simulations of aircraft response to wind shear. Fixed-stick, autopilot, and manned computer simulations are made with an aircraft having characteristics of a Queen Air (small commuter-type aircraft) flown through longitudinal winds measured by a Doppler radar beamed along the glide slope during the SESAME '79 experiments in Oklahoma. Simulations are also made flying a model Boeing 727 through sinusoidal head wind to tail wind shears at the phugoid frequency to evaluate the response of manned aircraft in thunderstorm wind environments.

Turkel, B. S.↗
NASA NTRS1980

Pilot-aircraft system reponse to wind shear

The nonlinear aircraft motion and automatic control model is expanded to incorporate the human pilot into simulations of aircraft response to wind to wind shear. The human pilot is described by a constant gains lag filter. Two runs are carried out using pilot transfer functions. Fixed-stick, autopilot, and manned computer simulations are made with an aircraft having characteristics of a small commuter type aircraft flown through longitudinal winds measured by a Doppler radar beamed along the glide slope. Simulations are also made flying an aircraft through sinusoidal head wind and tail wind shears at the phugoid frequency to evaluate the response of manned aircraft in thunderstorm wind environments.

Turkel, B. S.↗